Search

This paper proposes unconventional control techniques for a portable power supply consisting of electric double-layer capacitors (EDLCs), a dc–dc converter, and a low-impedance load such a plasma load. Between the EDLCs and the plasma load consuming high power, a dc–dc converter is required to control the output voltage from the rapidly decreasing voltage of EDLCs. In addition, the dc–dc converter should maintain a set point by responding to arcs occurred in plasma process. This paper proposed hybrid analog and digital controls for a nonideal boost converter which was setup by theoretical analysis. The proposed system is verified with experiment and simulation. As a result, the proposed control method can maintain the constant output voltage longer than a traditional analog pulsewidth modulation control. [ABSTRACT FROM AUTHOR]

Power supplies have played crucial role to improve and extend plasma applications. Several dc, pulsed, and radio frequency (RF) stabilized power supplies have been developed over a wide range of frequencies and voltage waveforms. However, the influence of voltage waveform on the plasma densification, mainly due to the secondary electrons emission from the electrodes, has not been quite explored. This paper proposes an asymmetric pulsed bipolar power supply, adjustable in frequency, amplitude, pulsewidth, and number of pulses for generation of cold plasmas. Short period positive pulses, between longer negative pulses, increase greatly the secondary electron emission from the electrodes and, consequently, the plasma ionization rate. Short pulses (ns) are obtained by the phase shift between each carrier, and the high-intensity pulses are obtained by cascading the cell submodules in a half-bridge cascade topology, using a modular half-bridge converter configuration. The intensity of the positive and negative pulses can be varied independently. There is no unintended dc voltage level between the electrodes, which appear in RF plasmas. The plasma generated in this way is free of electric arc and can be kept stable within a broader range of operating parameters, mainly the voltage and the working gas pressure. [ABSTRACT FROM AUTHOR]

This paper describes a high-frequency pulsed-power generator for various industrial applications such as water treatment, food and medical apparatus for sterilization, or polluted gas treatment. The system is made of silicon-controlled rectifier as a main trigger switch, capacitors, two-stage magnetic pulse compression stages, and a linear transformer to generate a maximum of 120-kV, 5-kA pulse. The parameters obtained through the development are: output voltage: 120 kV (maximum), pulse repetition ration: 300 pulse per second, pulsewidth: 0.25~\mu \texts , and mean power: 30 kW. The designed pulsed-power generator is confirmed to be used effectively for many high-voltage pulsed-power applications related to environmental industry by simulation and experiments. [ABSTRACT FROM AUTHOR]

A 200 kJ pulsed power system (PPS) has been built up to drive pulsed plasma devices. This PPS consists of two 100 kJ capacitor bank modules, each comprising of five capacitors of each 178~\mu \textF , a discharge switch, and a pulse-shaping unit. When both the banks are charged simultaneously to −15 kV using full charging technique, it delivers a peak current 100 kA at the load (damping resistor and pulse-shaping inductor). Later on, a plasma system will be attached at the load which will also have an inductive and resistive effect. A fiber-optic triggering unit controls both the modules and there exists a flexibility of sometimes operating a single module only, besides there are provisions for further up gradation of the PPS to a targeted 600 kJ. Prior to this development, PSpice simulation was carried out to estimate the parameters of the circuit components to achieve the required wave pulse with precision. Using these parameters, a design of the PPS was made keeping into account about the critical issues involved and the ratings of the components, some of which were fabricated in house. This paper basically includes the criticality surrounding the operation of a high-energy long-pulse PPS under negative operating voltage. [ABSTRACT FROM AUTHOR]

This paper presents a power electronics converter to generate bipolar high-voltage pulses using low-voltage dc source. Converter is designed based on charging of different capacitors by a predetermined switching pattern and their discharging on the load for pulsed power applications. Low number of power electronics devices and bulky transformer elimination are main advantages of the proposed converter. According to new findings, bipolar high-voltage pulses may lead to higher efficiency in many applications, such as food sterilization industry. The proposed pulse generator generates bipolar controllable pulses with a modular circuit structure based on a capacitor-switched network. Experimental results are presented to verify the analysis. [ABSTRACT FROM AUTHOR]

This paper presents a high-voltage pulsed-power system based on low-voltage switch–capacitor units that are connected to a current source for several applications such as plasma systems. A modified positive buck–boost converter topology is used to utilize the current source concept, and a series of low-voltage switch–capacitor units is connected to the current source in order to provide a high voltage with a high voltage stress (dv/dt) as demanded by the loads. This pulsed-power converter is flexible in terms of energy control because the stored energy in the current source can be adjusted by changing the current magnitude to significantly improve the efficiency of various systems with different requirements. The output-voltage magnitude and stress (dv/dt) can be controlled by a proper selection of components and control algorithm to turn on and off the switching devices. [ABSTRACT FROM PUBLISHER]

This paper describes the construction and experimental tests of a 12-kV high-voltage high-action generator based on reverse-switching dynistor (RSD) assembly. The main RSD unit consists of seven 76-mm-diameter dynistor pieces connected in series with a blocking voltage of about 2.4 kV, a magnetic switch based on a 1K101 amorphous alloy core, the trigger system based on a saturable transformer, and a 16-mm RSD assembly; the trigger current could reach 2 kA in amplitude with 1-\mu\s duration under 10 kV. The working voltage rate of this RSD unit is about 8–12 kV. Experiment on a 2.2-mF capacitor test bed under 12 kV working voltage, the switch current amplitude reached 150 kA with 300-\mu\s duration; the transferred charge is about 26.5 C and the action is 2.94 \MA^2\s, respectively. [ABSTRACT FROM AUTHOR]