Search

The multigap gas switch has been widely used in liner transformer drivers (LTDs), but there is still room for improvement on its self-breakdown and triggering characteristics. In this paper, based on the circuit model of the six-gap gas switch, the gap voltage distribution during the charging and triggering process is analyzed, and the optimization on self-breakdown and triggering characteristics by mounting resistors and capacitors in parallel with switch gaps are theoretically and experimentally investigated. The results indicate that compared with the original switch, when the self-breakdown voltage is about ±90 kV, the standard deviation is reduced from 7.5 to less than 3 kV; for a charging voltage of ±80 kV and by operating at 60% working coefficient, when the negative trigger voltage is 75 kV, the jitter of the switch is reduced from 6.1 to 1.4 ns. [ABSTRACT FROM AUTHOR]

The meat grinder is a basic circuit for inductive pulsed-power supply (IPPS). Based on meat grinder, the Institute of Advanced Technology proposed a circuit called the slow transfer of energy through capacitive hybrid (STRETCH) meat grinder, in which an Integrated Gate Commutated Thyristors (IGCT) is selected as the main switch. Tsinghua University proposed the STRETCH meat grinder with inverse current commutation with semiconductor devices (ICCOS) in which the main switch is replaced by a thyristor and the ICCOS subcircuit is introduced to turn off the main switch. To reduce the opening switch voltage and increase the current turning-off capacity for IPPS, this paper presents a novel circuit topology named the meat grinder with self-charged capacitor and thyristors (SECTs). The key idea of the SECT topology is to turn off the primary current by the energy transfer capacitor, which is precharged. The meat grinder with SECT has larger capacity than the STRETCH meat grinder because it replaces the IGCT with a thyristor and is simpler than the STRETCH meat grinder with ICCOS because it only needs one capacitor. The suggested circuit is more suitable for IPPS module with high energy density. Simulation and experiment have been carried out to validate the circuit. [ABSTRACT FROM PUBLISHER]

The series configuration of fast semiconductor switches seems to be the key component in the high-voltage and fast rising time pulse generation. In this approach, two important issues must be considered. The first is to provide a safe operating condition for the switches in transient intervals. The second is to design a gate drive system with the capability of driving a large number of discrete devices simultaneously. The aim of this paper is to obviate these two requirements. First, different factors affecting the unbalanced voltage sharing between the series switches are discussed. In this investigation, the switch-to-ground parasitic capacitance effect has been recognized as the major effect on the unbalanced voltage sharing in the transient interval. Two schemes for abating this effect are proposed. To solve the unbalanced voltage distribution, the structure with a snubber circuit in the clamp mode operation is suggested. This scheme can be used for any number of switches without destructively affecting their behavior. In addition, the output pulse with a fast rising time could be obtained by the proposed gate drive system. In order to evaluate the operation of the proposed structure, a stacked switch with the voltage capability of 36 kV is tested experimentally. The characteristics of the obtained pulse are the fast rising time (69.5 ns) with the dV/dt of 460 kv/ \mu \texts and the wide range of the pulsewidth adjusting to 0.5–15 \mu \texts . In addition, the voltage variance of the switches level in the series structure is about 10%. [ABSTRACT FROM AUTHOR]

When small currents are interrupted by a vacuum switch, it is well known that the chopping current and the associated overvoltage are observed. Many investigations on the current-chopping phenomena in alternating-current (ac) circuits have been carried out, but there are no data available on inverter circuits in spite of their recent wide application to synchronous motor systems. In this paper, chopping-current levels and the overvoltages in an inverter circuit under a simple three-level pulsewidth-modulated control are investigated. As a result, the mean chopping-current level is three to four times higher than that in an ac circuit. In particular, high chopping currents occur only when the timing of the current interruption by the vacuum switch synchronizes with that of the inverter's switching, which we call “double chopping.” High chopping current due to double chopping might be harmful since the high overvoltage proportional to the chopping-current level could damage the insulation of electric equipment. However, we experimentally confirmed that a typical surge suppressor could reduce overvoltage. [ABSTRACT FROM AUTHOR]

It is difficult to design a standard gate driver for optimal switching control of a static induction thyristor (SI-Thy) because of its unique internal structure and the direct commutation switching characteristic between the gate and cathode terminals during the transient turn-on and turn-off switching phases. Therefore, it is important to develop a simple and effective gate driver for achieving optimal fast turn-on and stable switching operations in an SI-Thy under hard-switching conditions. To achieve faster turn-on switching time with shorter gate delay time, impedance matching between the SI-Thy and the turn-on driving circuit component in the gate driver can be realized with additional circuit modification through this paper. To ensure higher stabilities in the turn-off switching phase, forced commutation techniques and additional auxiliary circuits in the gate driver have been devised to suppress the latchup and to eliminate potential ringing possibility. We have demonstrated that our designed and tested gate driver for realizing optimal switching characteristics of an SI-Thy is effective, particularly in the gate driving circuits for various pulsed-power switching applications. [ABSTRACT FROM PUBLISHER]

This paper describes the construction and experimental tests of a 12-kV high-voltage high-action generator based on reverse-switching dynistor (RSD) assembly. The main RSD unit consists of seven 76-mm-diameter dynistor pieces connected in series with a blocking voltage of about 2.4 kV, a magnetic switch based on a 1K101 amorphous alloy core, the trigger system based on a saturable transformer, and a 16-mm RSD assembly; the trigger current could reach 2 kA in amplitude with 1-\mu\s duration under 10 kV. The working voltage rate of this RSD unit is about 8–12 kV. Experiment on a 2.2-mF capacitor test bed under 12 kV working voltage, the switch current amplitude reached 150 kA with 300-\mu\s duration; the transferred charge is about 26.5 C and the action is 2.94 \MA^2\s, respectively. [ABSTRACT FROM AUTHOR]