Search

Studies have been taken into the breakdown voltage jitter of corona-stabilized switch at high repetition rate up to several kHz. It is thought that the gas recovery affect the jitter of breakdown voltage directly at high repetition rate, because the gas switch will breakdown at a low voltage if the gas cannot fully recover. The breakdown voltage jitter is called voltage jitter in the following paper. However, based on the experimental results, the voltage jitter still exists at low repetition rate, even at single-shot mode. This is not explained by the previous studies. In this paper, voltage jitter below 100 Hz of a corona-stabilized switch is investigated experimentally. A corona-stabilized switch is introduced, using a cylindrical electrode as the cathode and a plane electrode as the anode. The gas used between the electrodes is SF6. A negative pulse with a maximum width of 30~\mu \texts is used to charge this switch. The tested factors include gas pressure, gap space, repetition rate, and switch geometry. Experimental results show that voltage jitter is mainly affected by the gas pressure and switch geometry. It is seen that voltage jitter decreases as gas pressure increases and a suitable cathode geometry presents a low voltage jitter. Critical volume is a region close to the highly stressed electrode, where the presence of an electron will lead to an electron avalanche which attains a critical size and hence leads to a stabilizing corona. Critical volume is introduced to explain the experimental results. It is found that less voltage jitter can be achieved with a smaller and more concentrated critical volume, as well as efficient corona stabilization. The results indicate that voltage jitter may be reduced by optimize the critical volume at low repetition rate. [ABSTRACT FROM PUBLISHER]

Bipolar junction transistors (BJTs) have been widely studied and used in nanosecond high-voltage pulse generators due to the advantages of fast switching speed and high repetitive frequency. Usually the Marx-type circuit is used to raise the peak value of output pulses. In this paper, a traditional BJT-Marx circuit using charging resistors is analyzed theoretically and experimentally. Based on the results, the structure of a circuit is changed to decrease the isolation voltage across the resistors, and diodes are used to replace charging resistors to block capacitors discharging to resistors. Experimental results showed that the three Marx generators proposed in this paper output pulses with higher voltage amplitude, and the last improved circuit outputs pulses with faster fall times at a higher efficiency. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

In this paper, a compact circuit topology is presented for pulsed power generation with a semiconductor opening switch (SOS). Such circuits require the generation of a fast forward current through the diode, followed by a reverse current that activates the recovery process. In general, magnetic switches are used to switch the diode current from forward to reverse. Therefore, adjustment of the output voltage of an SOS pulser is difficult. This paper introduces a circuit that allows an adjustable output voltage of the pulser. A solution is realized with a premagnetizing circuit on the primary winding of a pulse transformer (PT), so that a third winding is not needed. The primary capacitor voltage can now be varied while maintaining proper saturation of the PT. [ABSTRACT FROM PUBLISHER]

Megavolt-class-triggered switches play a key role in large-induction voltage adder accelerators. This paper introduces a 2.8-MV, low-inductance, low-jitter, electrical-triggered, gas SF6 switch. The main section is a $V/n$ switch and the pretrigger section is a trigatron switch. Based on electric field simulation, experiment, and analysis, the structure and spacing of gaps, location of trigger disk, diaphragm, and switch inductance are all discussed. The primary test indicates that the switch can be operated in the range of 0.85–2.76 MV with the pressure of the SF6 changing from 0.1 to 0.9 MPa. The self-breakdown voltage is linearly related to the logarithm of the pressure, as the gap spacing and the voltage rise time are fixed. Three working modes were observed: self-breakdown, self-triggered, and ex-triggered. In the triggered modes, the switch jitter is <3 ns and the switch inductance is usually below 150 nH. [ABSTRACT FROM AUTHOR]

The basic structure and work mechanism of laser-triggered vacuum switch (LTVS) are introduced briefly in this paper, and the processes of primary plasma production and expansion are analyzed as well. A series of experiments has been carried out with different gap voltages, laser wavelengths, laser energies, polarity configuration modes, switch structures, focal lengths, and laser waveforms. The switch structure is modified to improve the heavy-current capability of the switch, and the gap distance is increased to improve the voltage capacity. The special design of the trigger structure can reduce the dependence on the laser energy of the switch and the time delay. A new laser waveform of LTVS multiple wave crests could further decrease the laser energy, and it is the research basis of laser trigger miniaturization and its application in the LTVS. [ABSTRACT FROM PUBLISHER]

This paper describes the design and implementation of a three-phase resonant converter with low ripple and high control accuracy. Based on a three-phase LCC-type resonant converter—which has advantages of low ripple, high-efficiency, and high-power density compared with a single-phase converter—a high-voltage power supply with low ripple (<0.1%) was designed. In addition to the general merits of an LCC-type resonant converter operating at continuous conduction mode—including soft switching, low conduction loss, and current source characteristics—the proposed scheme uses only one phase under a light-load condition by having different leg designs of the gate drive circuit and snubber parameters. This allows the design to overcome the operational constraints of the general LCC-type resonant converter. The distinctive design of the three-phase converter structure provides high efficiency and low ripple not only during rated operation, but also under light-load conditions. In order to analyze the high performance of the proposed scheme from no load to rated load, a PSPICE simulation was carried out. Comparison results with a conventional LCC-type resonant converter based on a single-phase structure are analyzed from the viewpoints of output ripple, losses, and operable load range. Using the proposed converter, a 20-kV, 20-kW high-voltage dc power supply design and implementation was presented with a superior gate drive circuit. Finally, the superiority of the proposed converter was verified through a simulation and experimental results. It was experimentally confirmed that the developed power supply achieves high performance in terms of efficiency (98%), operable load range (0.5–20 kV), and low ripple (0.05%), with a high power density. [ABSTRACT FROM PUBLISHER]