Search

The planned China fusion engineering test reactor (CFETR) needs one or more negative-ion-based neutral beam injectors (N-NBIs) with a beam energy of 500 or even 1000 keV. In order to prepare for CFETR, a prototype of CFETR N-NBI is being designed. The prototype needs an acceleration grid power supply (AGPS) rated at 200 kV/25 A with a maximum pulselength reaches to 3600 s. The AGPS adopted a single-stage inverter-type high-voltage power supply (HVPS). The output voltage ripple is an important specification of the AGPS, which can affect the efficiency and stability of N-NBI system by influencing the beam divergence. However, the conventional methods cannot be used to limit the output voltage ripple of the inverter-type HVPS used as AGPS of CFETR N-NBI prototype. This paper simplified the AGPS to an insulated three-phase three-level (TPTL) dc–dc converter connected with a dual dc link. The working process of the TPTL dc–dc converter with duty-cycle modulation has been analyzed, and two main continuous conduction modes are described. The influence of key parameters such as duty cycle of inverter, leakage inductance of transformer, and output current on output voltage ripple is analyzed. Based on the analysis results, a so-called combined control strategy was proposed to keep the output voltage ripple at a level. The proposed strategy is suitable for the cases where the object output voltage is below 175 kV. Some simulations were carried out by using MATLAB/Simulink. The results showed that the analysis in this paper is reliable and the proposed control strategy has a good performance. [ABSTRACT FROM AUTHOR]

This paper proposes an active resonance circuit based on multiple series gaps (MSG) with voltage-dividing network and self-charging trigger device. The working principle of active resonance circuit, MSG, and triggering device is described in detail. To determine the optimal parameter setting of MSG, the effects of the voltage frequency, equalizing resistance, and voltage-dividing capacitance on the voltage distribution of MSG are analyzed by simulation. To realize the interrupting process of short fault current and determine the operation requirements of the main devices of precharge direct current (dc) circuit breaker, a simulation model of interrupting short fault current is performed. Furthermore, an experiment of four-series gaps is presented to verify the turn-on characteristic of the MSG and an experiment of artificial current zero is set up to testify the feasibility of the active resonance circuit. The simulation and experimental results show that the active resonance circuit proposed in this paper can generate an artificial zero current and is suitable for precharge dc circuit breaker. [ABSTRACT FROM AUTHOR]

The acceleration grid power supply (AGPS) is an important part of the neutral beam injector (NBI) system. With the increase in NBI power, the requirement for output voltage of the AGPS is becoming higher and higher, even reaching to 1000 kV. As the inverter-type high voltage power supply uses inverters located at the lower voltage side to regulate and cut off the output voltage, it is very suitable for high-voltage applications. The proposed scheme for the AGPS of the International Thermonuclear Experimental Reactor (ITER) NBI system comprises five stages, where each stage has an inverter-type power supply with an output voltage of 200 kV. This paper investigates the inverter-type power supply based on neutral point clamped three-phase three-level (TPTL) inverter and three-phase step-up transformer, which is equivalent to an insulated TPTL dc–dc converter connected with a dual dc link. In order to design a preferable controller for the inverter-type power supply, the topology and principles of the TPTL dc–dc converter with duty cycle modulation have been analyzed. It indicates that only when the converter operates at a large duty cycle, the output voltage ripple can be limited to ±5%. Hence, the small signal model of the converter at a duty cycle larger than 2/3 is established. Following the mathematical model, a single-loop PID controller has been designed and a 400 V/6 A prototype has been built. Simulation and experimental results verify the correctness of the theoretical analysis. The system achieves a lower output voltage ripple and fast dynamic response. [ABSTRACT FROM AUTHOR]

When small currents are interrupted by a vacuum switch, it is well known that the chopping current and the associated overvoltage are observed. Many investigations on the current-chopping phenomena in alternating-current (ac) circuits have been carried out, but there are no data available on inverter circuits in spite of their recent wide application to synchronous motor systems. In this paper, chopping-current levels and the overvoltages in an inverter circuit under a simple three-level pulsewidth-modulated control are investigated. As a result, the mean chopping-current level is three to four times higher than that in an ac circuit. In particular, high chopping currents occur only when the timing of the current interruption by the vacuum switch synchronizes with that of the inverter's switching, which we call “double chopping.” High chopping current due to double chopping might be harmful since the high overvoltage proportional to the chopping-current level could damage the insulation of electric equipment. However, we experimentally confirmed that a typical surge suppressor could reduce overvoltage. [ABSTRACT FROM AUTHOR]