Search

As part of the ongoing China Fusion Engineering Test Reactor (CFETR) studies, this work focused on the study of the electromagnetic (EM) loads distribution on inboard (IB) and outboard (OB) blanket vertical segments. In this paper, a major central disruption scenario with a 36-ms linear current quench was performed in the ANSYS finite element software. EM forces and moments, both on the single module and the complete blanket segment, were calculated for the updated helium-cooled ceramic breeder (HCCB) blanket. Furthermore, the effect of EM loads with respect to poloidal segmentations on the back plate (BP) was studied. Results show that the EM forces and moments in the IB blanket barely changed, but in the OB blanket, great changes occurred. With poloidal segmentations increasing, EM forces loads on the BP will be reduced. This paper may provide important data to support subsequent optimization of the BP of CFETR and could also be a technical reference for other fusion organizations. [ABSTRACT FROM AUTHOR]

This paper has introduced two important indexes, turn-off surge voltage (TSV) on power switch and peak positive pole potential (PPPP) of storage batteries, which can be used to evaluate switching transient process of high-voltage energy storage system. Research on them is of great significance to power switch choice and high-voltage isolation design in engineering applications. Power switch response process at the turning off moment and transient process in freewheel stage have been analyzed by the established small-signal model of single power switch; then, a power switch test platform for hybrid energy storage system was built to verify it. Taking pulsed-power supply charging device with a novel inductor of low resistance and high inductance as a research object, this paper has analyzed dynamic process of the TSV and the PPPP at the turning off moment through establishing state space model of the whole system. Comparison shows that the numerical curves match the simulated curves well. Finally, the exactness of the employed model has been further verified in two pulse capacitor charging experiments. [ABSTRACT FROM AUTHOR]

In this paper, a new configuration of dielectric-barrier discharge (DBD) reactor with three electrodes was manufactured and used to produce ozone. Designed flatly, this reactor is capable of establishing three different discharge modes from type of the volume and surface discharges, without modifying its internal structure. The aim of presenting this paper is to experimentally analyze the three discharge modes and their combination using a second channel to produce ozone. The two reactor channels are identical in terms of dimensions, material, and manufacturing process. Two frequency-adjustable pulse generators of the same electrical characteristics and two high-voltage transformers were used in the course of the experiments. The applied sinusoidal voltage is from 0 to 12 kVp-p. The frequency range was determined and fixed for all three discharge modes for the highest ozone concentration at a fluctuation rate of 1 L/min. Effects of increasing the applied voltage on the obtained concentration from the three different discharge modes were experimentally analyzed. Using the provided inlets–outlets, the effect of flowing gas through the length and width of the discharge area on ozone concentration was investigated, and appropriate flow directions were determined for the flowing gas under either of the three discharge modes. Experimentally results have been done for this three discharge modes as well as hybrid modes. The maximum ozone production rate achieved up to 14.52 g/h in the series combination of two different volume discharge. At 96% oxygen purity, ozone production yield, in two modes volume discharge VaDBD and surface discharge SDBD, have been improved up to 529.87 g/kWh. However, the total input power of the entire system is 120.2 W. [ABSTRACT FROM AUTHOR]

In inertial confinement fusion, the scientific issues include the generation and transport of driver energy, the pellet design, the uniform target implosion physics, and the realistic nuclear fusion reactor design. In this paper, we present a pellet injection into a power reactor in heavy-ion inertial fusion (HIF). We employ a magnetic correction method to reduce the pellet alignment error in HIF reactor chamber, including the gravity, the reactor gas drag force, and the injection errors. We found that the magnetic correction device proposed in this paper is effective to construct a robust pellet injection system with a sufficiently small pellet alignment error. [ABSTRACT FROM AUTHOR]

This paper will describe the influence of mesh geometry on the homogeneity of discharges, power, and efficiency of ozone generation. Homogeneous discharges increase the efficiency of the generation of ozone. Geometry of mesh electrodes affects the power and type of discharges, concentration, and efficiency of the ozone generation. The analysis of selected results indicates the need for the use of mesh electrodes with a small cross section at least $0.1\times0.1$ mm2 mesh to obtain a homogeneous discharge. The mechanism by which the geometry of mesh electrodes on the homogeneity of discharge is illustrated in this paper. Homogeneous discharges increase the efficiency of the generation of ozone that reduces the cost of ozone production. The results of the experimental studies show an increase in the average efficiency of 60% of the ozone generation and a 20% reduction in the demand for power with the constant concentration of ozone, justifies the problem. [ABSTRACT FROM AUTHOR]

This paper presents a shutdown dose rate (SDR) calculation to estimate a newly developed preliminary concept of the equatorial port model for the Korean fusion demonstration reactor (K-DEMO). The equatorial port model was designed to provide effective radiation shielding abilities adopting the port shielding block and labyrinth structure, which was integrated into the modified K-DEMO neutronic analysis model by the Monte Carlo automatic modeling system. A rigorous two-step method was applied to couple transport (MCNP) and activation (FISPACT) codes according to three steps of calculation procedures. The results of neutron flux and decay gamma transport calculation for the equatorial port area have been indicated in this paper. The SDR calculation result near the equatorial port area reveals that a dose level in the equatorial port interspace was below $100~\mu $ Sv/h after 12 days of the shutdown. Shielding blocks and two labyrinth structures prove that they effectively attenuate neutrons on the current concept of the equatorial port model. [ABSTRACT FROM AUTHOR]

High-voltage power supplies (HVPSs) are widely used to supply vacuum tubes. The amount of delivered energy from the HVPS to the tube is an important issue during the vacuum arc in the tube. The conventional protection mechanism consists of a shunt crowbar which diverts the fault current from the tube to itself as a parallel path. The crowbar circuit is usually built of the devices without the turn-off capability. It is a drawback since the output of the power supply is shortened for a long time. Thus, the restoration time of these power supplies is excessive. This demerit can have detrimental effects on mission-critical applications. In this paper, the insulated-gate bipolar transistor (IGBT)-based crowbar structure is studied to overcome this issue. In the proposed protection mechanism, the crowbar can be reopened intentionally after closing. A theoretical analysis is presented to compare power supply performance in the presence of the conventional crowbar with the IGBT-based crowbar. The experimental results are presented to demonstrate the practical considerations of the proposed crowbar structure and its appropriate performance. This paper shows that HVPS has more fault resiliency and less restoration time with the proposed IGBT-based crowbar. [ABSTRACT FROM AUTHOR]

This paper embodies the results of experimental studies of a dielectric barrier discharge low-temperature nonequilibrium plasma reactor that runs in air and nitrogen at atmospheric-pressure conceived for surface treatment applications. A homemade reactor, of typical plane-to-plane geometry with the dielectric covering the upper electrode which is stressed by a high voltage (40 kV, 3–20 kHz) is used. Electrical signals (current and voltage), optical emission spectroscopy records, and total light emission measured by photomultiplier have been analyzed and used to distinguish different plasma regimes which are studied for the treatment of a lignocellulosic material (sugarcane bagasse). In the filamentary discharge regime, the gas temperature of few tens of degree Celsius above the ambient one was determined, the electronic temperature of some electronvolts and electron density in the range of 1012–1013 cm−3 were estimated. Plasma treated pellets of sugarcane bagasse were analyzed by diffuse reflectance infrared Fourier transform spectrometry and the relative results obtained under filamentary discharge regime have shown significant degradation of the lignin macromolecule. It has been shown important modifications on the lignocellulosic material, namely, the plasma attacks drastically the lignin bonds. Strong modification of lignin was observed near wavenumber of 3400 cm−1, due to stretching vibrations of OH, and for the band 1114 cm−1 which is related to C=C and C=O stretching. Severe decrease of the band intensity 1596 cm−1, which due to C=C stretching and C=O, is also a result of the treatments done in this paper. [ABSTRACT FROM AUTHOR]

One of the conceptual designs of the breeder blanket for a European demonstration fusion power station (DEMO) is the water-cooled lithium lead (WCLL) concept. The design development of the WCLL blanket in recent years has undergone the evolution of the neutronics model employing the MCNP code, with key changes in radial lengths and thickness as well as dimensional differences in inner structures such as breeding zone, shielding zones, and manifold. Furthermore, there has also been a significant increase in projected fusion power. Such changes were made with respect to its nuclear, thermohydraulic, and thermomechanical performances. In this paper, neutronic characteristics of WCLL modules were analyzed in terms of fusion power increase and dimensional changes of the blanket geometry presented in DEMO 2014 and 2015 models. For comparison, outboard and inboard blanket modules of the equatorial region were selected. Investigated neutronic characteristics include activity, decay heat, and contact dose rates. The numerical experiment was carried out with MCNP particle transport code and FISPACT/FISPACT-II activation calculation codes with EAF-2010/TENDL-2015 nuclear data libraries. [ABSTRACT FROM AUTHOR]

Photoelectric characteristics are an important reference for high-voltage discharges and are closely related to the excited mode of the high-voltage source. In this paper, we built a large-scale volume dielectric barrier discharge (DBD) system, which is composed of multilayer parallel-plate DBD electrodes and is excited by a high-voltage source in the power density modulation (PDM) mode. Subsequently, we analyzed the applied energy equation and evaluated the DBD systems photoelectric characteristics. The results show that the energy values of different applied voltage cycles during a PDM period exhibit significant differences. However, the average energy in a PDM period is approximately constant. Moreover, the equivalent capacitance of the DBD cell is a function of both the applied voltage and energy density. For the DBD cell, with the increase in both the applied voltage and energy loaded on the DBD cell, the total equivalent capacitance ($C$) is approximately constant, the dielectric capacitance ($C_{\mathrm{ d}}$) increases exponentially and decreases linearly, while the discharge gap capacitance ($C_{\mathrm{ g}}$) decreases and increases in the same cases. In addition, the relative intensities of the discharge emission increase and the energy efficiency ratios of the relative photoquantum yield of active species decline with the increase in both the applied voltage and energy density loaded on the DBD cell. The experimental results have been analyzed by evaluating the influence of the electrical parameters, and the underlying physical principles have been discussed. This paper clearly demonstrates that the photoelectric characteristics of the DBD reactor are significantly influenced by both the applied voltage and energy density, thus providing helpful insights into the energy evaluation and application of high-voltage discharges. [ABSTRACT FROM AUTHOR]

The increased usage of diesel fuel of late has led the researchers to pay more attention toward abatement of increased emission of oxides of nitrogen (NOx) in the engine exhaust. The focus is, therefore, lies in providing a technique that is economical, feasible, and long lasting. The combination of electric discharge plasma with adsorbent/catalyst derived out of solid waste can be one such possible technique. In this paper, waste foundry sand from foundry industry and red mud or bauxite residue from aluminum industry have been used. Diesel engine exhaust under dry condition was exposed to an oxidizing discharge plasma environment. The plasma-treated exhaust was subjected to either adsorption over waste foundry sand or catalysis over red mud. Studies were carried out in the laboratory environment with 20% loading of diesel generator. The oxidizing plasma environment was either with direct plasma or with indirect plasma in which case ozone injection into the exhaust was accomplished. The ozone-adsorbent cascading system has resulted in about 87% NOx reduction in the dry exhaust case. The effect of O3:NO ratio was discussed from the point of NO/NO2. [ABSTRACT FROM AUTHOR]

Nonlinear transmission lines (NLTLs) have been studied over the past several years to generate high-power radio frequency signals. Their operation consists of a lumped line based on the nonlinear behavior of the LC section components, capacitors or inductors, as a function of the applied voltage or current, respectively. However, considering high-power signals, the application of these devices using nonlinear ceramic capacitors as the capacitive lumped lines are restricted to frequencies around 100 MHz since at high voltages, parasitic impedances in the line structure limit the maximum operating frequency. On the other hand, the use of variable capacitance diodes has enabled the operation of NLTLs at higher frequencies. This paper provides the results of a study of NLTLs for RF generation based on silicon carbide Schottky diodes. The principle of operation and its simplified theory are presented. Initially, the voltage dependence of the diode capacitance is modeled. Experimental and simulation results are compared. Frequency oscillations around 200 MHz were generated. The extraction of the radio frequency energy is realized, and the radiation of the electromagnetic wave is performed using double-ridged horn antennas. Finally, some parameters are analyzed, and all results discussed. [ABSTRACT FROM AUTHOR]

Air-borne micrometer and submicrometer particles produced by anthropogenic sources contaminate atmospheric air, especially in large cities where both population and industrial activities are higher leading to a reduced air quality. Recent research has pointed out particles less than 2.5 \mum in diameter (PM2.5) as a potential health hazard. To address this issue, stricter legislation has been put into force to reduce PM2.5 emissions. This paper is focused on the development of an impulsive microelectrostatic precipitation technology for charging and removal of fine air-borne particles in an economically feasible way. In this paper, a compact coaxial precipitator has been developed for possible indoor air cleaning applications. High-voltage impulses together with dc voltage have been used for energization of the reactor as it has been shown to enhance the precipitation efficiency. This precipitation system has been used for removal of fumes and fine air-borne particles from ambient air. In addition to the experimental part, analytical work has been conducted to optimize the electrostatic precipitation process and to reduce its power consumption. [ABSTRACT FROM PUBLISHER]

This paper describes a study on the high-voltage compact solid-state pulsed-power modulator for parallel reactor operation. The current capacity of the pulsed modulator has been improved to drive multiple reactors in parallel. The pulse discharge switch uses the IXYK120N120C3 (1200 V/120 A) insulated-gate bipolar transistor for a high current output. The gate driver has been improved according to the characteristics of the replaced switch. The output specifications of the modified pulsed-power modulator are a maximum output voltage of 40 kV, a maximum output current of 300 A, a pulsewidth ranging from 1.5 to $5~\mu \text{s}$ , a maximum repetition rate of 3 kHz, and an average power of 13 kW. The modulator has the dimensions of $450 \times 475 \times 600$ mm3, a maximum peak power of 12 MW, and a maximum power density of 93 kW/L. A resistive load experiment and a plasma reactor parallel drive test were performed. Four parallel reactors were driven using one modulator. In addition, a 50% reduction in the concentration of toluene was obtained through the experiment of the toluene gas treatment using only parallel plasma reactors. [ABSTRACT FROM AUTHOR]

Dielectric barrier discharge (DBD) is a promising technology for ozone generation. In this paper, each electrode consists of tungsten rod and quartz glass. To improve the discharging efficiency, the air of the used quartz tube was evacuated. Moreover, to evaluate the performance of ozone formation, the electrical characteristics of volume DBD (VDBD) (two electrodes) and coupled VDBD (three electrodes and seven electrodes) are investigated. Under the condition of the same electric field using the COMSOL Software, the density of the current pulses is shifted to the right in the current waveforms. The results of ozone production show that a dynamic balance between ozone formation and ozone decomposes is complex at high frequency and high flow rate. The highest energy yield is 1650 g/kWh at a specific input energy of 0.6545 J/L. [ABSTRACT FROM AUTHOR]

The steady state with duty cycle time 0.3–0.5 of Chinese fusion engineering testing reactor (CFETR) is a big challenge. To realize this goal, the divertor should be reliable. At the preconceptual phase of CFETR design, reliability engineering is engaged to determine how reliable of divertor is and how much level of reliability of divertor should be. The plasma facing components (PFCs), base plate, and support frame have been considered during the reliability analysis for the divertor modules. The relation of the reliability between a divertor system and its modules has been analyzed. The relations between steady-state operation with duty cycle time 0.3–0.5 and the reliability of divertor is studied in this paper. How the reliability of components, modules, and divertor system affects the duty cycle time of CFETR is also analyzed. To meet the requirement of duty cycle time, the lowest reliability level of divertor system is 0.3679 and its mean time to fail is only 1 year. The divertor system with such low reliability requires that each module should have a relative high reliability of 0.9794, and then, the PFCs should have higher reliability of 0.9930. These results are then must become the requirements for the engineering design of CFETR divertor in the future. [ABSTRACT FROM AUTHOR]

The new tokamak generation will be characterized by the necessity of full remote maintenance for most of the critical components. Because no human intervention can be envisaged, the remote systems will have to prove high reliability and rescue capabilities. The availability of the fusion facility will have to be maximized, as a consequence, the efficiency of the maintenance equipment will become a key factor. To fulfill these constraints, the remote maintenance principles will need to be simplified as much as possible and be taken into account at the early stages of the tokamak design. This is an iterative process between Tokamak and Maintenance designs in order to reach the best possible tradeoff. Such an exercise of this iterative work was done on the China Fusion Engineering Test Reactor (CFETR) preliminary design. Main targets were established in the view of optimization of the remote maintenance, then an assessment of the first maintenance scenario, envisaged for the in-vessel components, was done and alternative solutions were proposed. This process was repeated during meetings with the tokamak subsystem owners. This paper will present the results of a first phase of optimization that can represent the current state of the remote maintenance design for CFETR. The work has provided guidelines for main tokamak subsystems such as the magnet configuration, the blanket and divertor modularity, the neutron shielding and cryostat arrangement, and the transfer and hot cell configuration. It also produced some innovative solutions for the overall maintenance scheme like the implementation of a hot cell at the top of the tokamak hall avoiding cask transfers. On this basis a CFETR maintenance scenario is proposed. [ABSTRACT FROM AUTHOR]

The international thermonuclear experimental reactor poloidal field converter unit is comprised of four converter bridges, dc reactors, dc switches, etc., and most are nonstandard. To evaluate the performance of these equipments, a high-power dc test platform has been built to carry out the steady-state current test and impulse current test. The latter is significant to verify the fault suppression capability of products. The dc test platform can output the rated 400-kA impulse current. The principle design and structure of the dc test platform is introduced in this paper. The transient large current in impulse current test could cause huge impact reactive power and grid voltage sag. The impact is analyzed by theoretical calculation and simulation. A static var compensator system is added to suppress the transient effects of the reactive power. A predictive reactive power control strategy is proposed to improve the dynamic response. The comparisons with the traditional control demonstrate that the proposed control is effective in compensating impact reactive power and it also performs well on inhibiting the grid voltage sag. [ABSTRACT FROM AUTHOR]

The halogen volatile organic compound (VOC) is a common industrial pollutant, mainly including trichloroethylene, dichloromethane, trichloroacetic acid, chloro-fluoro-carbons, carbon tetrachloride, trihalomethans, chlorodifuoromethanes, hydrofluorocarbons, and some other fluor alkaline, ether, and amine. The halogen VOCs have reproductive toxicity, immunotoxicity, and neurotoxicity. The traditional methods for treating them include masking method, dilution method, chemical oxidation method, incineration method, UV oxidation method, photocatalytic oxidation method, absorption method, and biological method. In this paper, advantages and disadvantages of traditional methods have been studied and analyzed. A new plasma technology has been put forward, which has the advantage of the rapid reaction to ambient temperature, wide applications, system compactness, simplicity of operation and short residual time, and the plasma technology is especially appropriate for the decomposition of VOCs. At present, as for the control of VOCs, the plasma technology has drawn much attention as an energy-saving technology. In this paper, the equipment for the decomposition of halogen VOCs has been analyzed, including the plasma rectors, power characteristics, operation conditions, and the decomposition mechanisms of C2HCl3, CH2Cl2, C2H3Cl3, CCl4, CHCl3, CF4, C2F6, and SF6 have been investigated and concluded. Finally, it is concluded that the combination of the plasma technology with traditional methods would be main direction of study in the future. [ABSTRACT FROM AUTHOR]

Based on the urgent needs for modularization and miniaturization of the inductive pulsed power supply system, this paper proposes the conceptual design and comparison of 100-kJ inductive storage power modules including four circuit topologies, three of which are proposed in our previous researches. The four circuit topologies are the STRETCH meat grinder, the XRAM with STRETCH meat grinder unit, the XRAM with strongly coupled inductors, and the XRAM with magnetic flux compression effect. The maximum load current of each constructed module is set to be 50 kA and its pulsewidth is at least 5 ms, which are the same as the main electrical properties of an existing 100-kJ capacitive module. A comparative study on energy density among the constructed inductive modules and the existing capacitive module is carried out in depth. Results show that the inductive modules, considering the volume of semiconductor switches and their control circuits, have higher energy density than that of the capacitive module. Among four constructed inductive modules, the XRAM with strongly coupled inductors module has the highest inductive energy density, and the XRAM with magnetic flux compression effect module has relatively better comprehensive performance. This paper offers the theoretical analysis foundation for investigating the inductive pulse power supply with higher energy. [ABSTRACT FROM PUBLISHER]

This paper investigated hydroxyl radicals and hydrogen peroxide formation under a needle-plate electrode configuration using positive-polarity dc discharges generated in air, nitrogen, and helium. The discharge mode in air and nitrogen was found to change above ultrapure water; initially, a nanosecond pulse discharge was observed, transitioning to a diffuse discharge due to the increasing conductivity of the water. The discharge in helium was a nanosecond pulse discharge and the repetition rate increased with increasing water conductivity. It was found that hydroxyl radicals contribute to 7%, 78%, and 70% of hydrogen peroxide formation when using the ultrapure water in air, nitrogen, and helium, respectively. It is suggested that hydroxyl radicals are formed by water reactions with energetic positive ions and the neutral particles, such as N2+, He+, O, H, and HO2. Part of hydrogen peroxide is directly formed from atoms and radical reactions with water in nitrogen and helium, while oxygen reactions are heavily involved for hydrogen peroxide formation in air. A fluorophotometry method, using terephthalic acid, was used to directly quantify the formation of hydroxyl radicals and compared with the tert-butanol method. [ABSTRACT FROM AUTHOR]

A pulsed discharge plasma (PDP) system with a multineedle-to-plate geometry electrode was applied in this paper to investigate the regeneration of granular activated carbon (GAC) spent with phenol in the PDP system. Regeneration percentage of the GAC under different conditions of initial solution conductivity and pH values was studied to clarify the regeneration of the GAC by the PDP. Formation of hydrogen peroxide (H2O2) with the same solution conditions was also investigated in this paper. The obtained results show that there was the same changing trend of GAC regeneration and H2O2 formation under different solution conditions, which clarify the critical effect of •OH on the GAC regeneration in the PDP system. The methods of scanning electron microscope (SEM), Brunauer–Emmett–Teller, Boehm titration, and Fourier transform infrared spectroscopy (FTIR) were used in this paper to demonstrate the medication of the GAC by the PDP treatment. The obtained results show that the regenerated GAC could recover a partial pore structure compared with the original GAC by the SEM analysis. The surface area, micropore volume, and total pore volume of the regenerated GAC increased, while the mesopore volume and the macropore volume decreased on the regenerated GAC; comparing with the original GAC, there was higher amount of acidic functional groups and lower amount of basic functional groups on the surface of the regenerated GAC; the intensities of O–H, C=C, C=O, and C–O enhanced significantly by the FTIR analysis. [ABSTRACT FROM AUTHOR]

Triple dc plasma torch system was used for the synthesis of nanoparticles. Three thermal plasma jets are ejected from each plasma torch and they are merged into a strong single plasma plume. Since the feedstock is injected into the jet merging area, this system is suitable for refractory nanoparticle synthesis and enable to high production yield caused by the complete evaporation is possible. In this paper, numerical simulation was carried out to analyze thermal plasma characteristic inside a reactor according to the plasma-forming gas and carrier gas compositions: Ar, Ar–H2, and Ar–N2 plasma; Ar, He, and N2 carrier gas. Then, it was comparatively interpreted with the actually synthesized nanoparticle in order to understand the condensation process of nanoparticles. It was revealed that the thermal environment is able to control readily in the triple torch system by the operating condition depending on the target materials. [ABSTRACT FROM AUTHOR]

In this paper, we discuss and demonstrate the potential of normally-on GaN high-electron-mobility transistors (HEMTs) as opening switches in miniaturized pulsed-power circuits. The high-breakdown electric field of GaN (~3 MV/cm) makes it possible to fabricate high-voltage devices in small dimensions, resulting in smaller parasitics and faster switching times. GaN HEMTs as opening switches are compatible with inductive topologies, which offer more than one order of magnitude higher energy density than capacitive topologies, allowing further miniaturization of pulsed-power systems. In this work, we demonstrate the application of fabricated 1.5-kV normally-on GaN HEMTs on an inductive switching topology, resulting in 300-fold voltage step-up, which makes it possible to generate high-voltage pulses with a low-voltage dc source in miniaturized circuits. [ABSTRACT FROM AUTHOR]

Theoretically, the energy conversion efficiency of the synchronous induction coil launcher (SICL) can reach 100%, but at present, the test data show that the highest current is only a little higher than 20%, which shows that the efficiency of the coil launcher has a lot of room for improvement. In this paper, three improved schemes are proposed for the topology of the traditional crowbar circuit based on the pulse capacitor to improve the electromechanical energy conversion efficiency of the electromagnetic coil launcher. They are main circuit breaking, crowbar break-off circuit, and crowbar circuit with inductor, respectively. In order to verify the feasibility of the above three methods, a five-stage coil launcher was simulated and analyzed. Then, based on the model, three improved circuits were calculated and analyzed by the finite-element simulation software. The results show that all of the three methods can improve the efficiency of energy conversion to a certain extent. Both the first and second methods have limited effect on increasing efficiency. In addition, they need to add some expensive equipment such as circuit breaker. So, they are not recommended. The third way of increasing an inductor in the crowbar circuit could increase the muzzle velocity and efficiency obviously. The muzzle velocity increased from 30.6 to 35 m/s. The effect of armature capture is reduced which is worthy of recommendation. [ABSTRACT FROM AUTHOR]

This paper proposed the use of a ringer, a self-switched inductive storage system, for applications involving reluctance accelerators, a kind of electromagnetic launcher, and compatible with applications where portability is a requirement. There will be shown three different useful approximations for the analysis of the ringer, employed as a power source for a reluctance accelerator. First, it described the equations governing the que behavior of an ideal unloaded ringer, and then the equations for the ringer with an uncoupled inductive load, and ultimately a Lagrangian model for the ringer as an inductive power source for a reluctance accelerator, capable to make predictions about the currents through the circuits and the exit speed of the projectile for a given firing. The accuracy of the predictions made with the third approximation, the Lagrangian model, was tested experimentally. [ABSTRACT FROM AUTHOR]

This paper is aimed at finding the effect of varying inductive energy storage systems’ (IESSs) inductance on resistance of an electrically exploded conductor-based opening switch and profile of current transferred into load, which has not yet been fully understood. Based on experimental results obtained, it is observed that when the inductance of IESS is varied, the magnitude of load current changes so as to conform to the magnetic flux conservation law but its rise time remains unchanged. Resistance of the opening switch and energy deposited in it has been estimated using recorded voltage and current waveforms. It has been found that with increasing inductance of IESS, the resistance of switch increases, whereas energy deposited in it decreases. Using these estimated values of energy, a possible explanation of observed behavior in resistance is presented. Effect of a mismatch between the inductance of IESS and load is seen to only affect the energy transfer efficiency or magnitude of load current but not its rise time emphasizing the novel finding that for a given load, the rise time of load current is independent of the inductance of IESS. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

According to the Chinese fusion engineering testing reactor (CFETR) central solenoid model coil (CSMC) properties test requirements, a large cryogenic test platform will be built. The feeder, as one of the important components of the platform, should be studied to afford the much valued help for the basic test facilities. This paper focuses on the feeder structural design and the stress analysis in conditions of different loads. All of the work could not only provide necessary help for building CFETR CSMC test platform but also provide the important service experience of the large cryogenic test platform in the future. [ABSTRACT FROM AUTHOR]

The departure from nuclear boiling (DNB) is an essential point for the heating channel with water flowing through, because when it happens, the water near the heated wall can be dried out, which will cause the material temperature exceeding the upper limits. Presently, the blanket is under design phase, and some essential parameters are uncertain, including the heat flux on the first wall (FW). For the sake of thermal safety, the occurrence conditions of DNB are analyzed solely, regardless whether material temperature exceeds the limits or not, in the FW of water-cooled ceramic breeder blanket for Chinese Fusion Engineering Reactor. This paper is useful for further blanket thermal design. Based on the lookup table that is summarized by experiments for the uniformed heating circular tube of 8 mm diameter, the local critical volumetric fraction of vapor, which acts as the evaluation criteria for the U-shaped FW of square channel with one-sided heating, is obtained using a computational fluid dynamics approach under different DNB operating conditions. After the comparison of phase distribution between different turbulence models, the K– $\Omega $ model is selected to do the calculation. The effects of coolant inlet temperature, mass flow rate, and operating pressure on DNB value are evaluated. Under the same operating pressure, either increasing mass flux or decreasing inlet temperature can reduce the critical vapor fraction. On the contrary, the DNB is enlarged effectively. Under the same inlet conditions, the lower operating pressure can increase DNB because of the higher latent heat of vaporization. [ABSTRACT FROM AUTHOR]

The external bypass, as an important component of the international thermonuclear experimental reactor (ITER) poloidal field converter unit (PFCU), will provide a freewheeling loop for the load current to protect the magnets and PF converter modules from being damaged by overcurrent and overvoltage under fault conditions. The triggering bypass protection test is used to verify that the designed bypass is triggered normally and endure the rated load current. In this paper, a suitable test scheme is designed for triggering bypass protection test of ITER PFCU based on the PF converter integrated test platform at the Institute of Plasma Physics, Chinese Academy of Sciences. This test scheme includes the triggering bypass method, calculating the trigger angle of the converter in inverter and a method of reducing the bypass current to zero in the absence of ITER mechanical switch. The feasibility of the test scheme is successfully verified by the simulation results and test results, both of which prove that the external bypass of ITER PFCU is triggered normally and withstands the load current for 100 ms. Due to the integrated inductance of the actual dc output circuit, the actual transfer time of bypass current in the test is more than the simulation results. [ABSTRACT FROM AUTHOR]

China Fusion Engineering Testing Reactor (CFETR) is a superconducting magnet tokamak. The research and development of the key technologies to the vacuum vessel (VV) manufacture have been carried out a few years ago by the Institute of Plasma Physics, Chinese Academy of Science, Hefei, China, including narrow-gap welding, cutting, and nondestructive testing. The manufacture of the poloidal segment (PS) for first 1/32 sector VV mock-up has been completed in 2015; the four PS sectors have been welded into a whole in 2016. This paper will describe the study of the welding process of the 1/32 VV mock-up for CFETR. [ABSTRACT FROM AUTHOR]

The water-cooled ceramic breeder blanket (WCCB) is one of the blanket candidates for the Chinese fusion engineering test reactor (CFETR). The conceptual of WCCB for CFETR under 200-MW fusion power has been designed based on pressurized water-cooled reactor technology. RELAP5 code, which is mature and often used in transient thermal–hydraulic analysis in pressurized water reactor, was selected as the simulation tool. In this paper, the nodal model for RELAP5 was developed corresponding to typical WCCB module, i.e., the coolant passages inside the module were nodalized as hydrodynamic components, and the associated module components were simulated with 1-D heat structures. The steady-state characteristic under full power was analyzed. The stable fluid, wall temperature distributions, and pressure drops were studied. The results were compared with those of the 2-D and 3-D computational fluid dynamics analyses by FLUENT. Furthermore, the transient characteristics under three accidental scenarios, in-vessel loss of coolant accident (LOCA), in-box LOCA, and ex-vessel LOCA, were analyzed, respectively. Simulation results show that the cooling of stiffening plates and side walls for breeder zone is very important for the blanket module. All the pressurization of the related volumes is within the design limits. The temperature of the structures does not exceed the limits for a relatively long time that allows mitigation measures to be taken. As for in-box LOCA, the exclusion of Be–water reaction makes the temperature nonconservative and still needs further study. [ABSTRACT FROM AUTHOR]

In this paper, a new architecture of a high-voltage Marx pulse generator based on isolated gate bipolar transistors (IGBTs) is proposed. It allows continuous control of the output voltage by acting on the IGBTs activation time: “on-time.” The final after-charging capacitors' voltage can be higher than the double of the input voltage. A simplified mathematical description of the system was developed in order to find a relation between the output voltage and the “On-time” (an open-loop control law). A SPICE simulation was implemented to check the expected performances and to verify the developed model. A three-stage generator was built according to the proposed structure using commercial IGBTs with a maximum output voltage of 3.6 kV. All results were compared to check and confirm the validity of the proposed architecture. [ABSTRACT FROM PUBLISHER]

This paper presents the design and experimental results of the 36-kW pulsed-power supply for the xenon flash lamp. The continuous conduction mode series-parallel resonant converter is modified. This means that not only the few hundred kilohertz of high switching frequency is introduced to replace the resonant inductor with the leakage inductor of transformer but also the high output current is accomplished by using three-phase delta-connected transformers. In addition, the snubber capacitor of the inverter switches and the power factor correction module is both omitted in the compact structure. Although these main components have changed, the efficiency and power factor of the rated dummy load reach 96% and 0.96%, respectively. Within 36-kW average power, the proposed pulsed-power supply can generate as versatile combination of output pulse. For example, it can generate 20-ms pulse with 1-Hz repetition rate or generate 1-ms pulse with 20-Hz repetition rate. The used insulated gate bipolar transistor is protected from the turn-OFF peak voltage by the snubber circuit, and the effect of the snubber circuit is shown at the actual load condition. [ABSTRACT FROM PUBLISHER]

A novel circuit with the better performance for the inductive pulsed power supplies in the electromagnetic launch system is proposed in this paper, namely, the meat grinder with capacitive pulse forming unit (CPFU). Its working process is qualitatively analyzed stage by stage. Its practical feasibility is verified through a 7.5-kJ experiment. From the perspectives of circuit structure and working principle, this circuit can be regarded as the combination of a meat grinder and a CPFU. Compared with its preceding circuits, this circuit possesses following advantages: 1) the self-recovery of the capacitor precharged voltage can easily be achieved, which is conducive to continuous operations of the whole circuit and 2) the waveforms of the inductor currents contain no capacitive components, which can promote the energy storage density of the inductors. [ABSTRACT FROM PUBLISHER]

The opening switch is one of the critical technologies in the development of inductive pulsed-power supply. The power requirement is very high when the opening switch is desired to commutate a large current. This paper presents a zero-current opening circuit for inductive pulsed-power supply based on a high-temperature superconducting pulsed-power transformer. First, there are two types of current flowing through the opening switch, one comes from the secondary side of the pulse transformer, and the other one comes from superconducting energy storage inductance. The orientation of the two current is opposite. Then, when the current flowing through the opening switch closes to zero, the switch is opened and this restrains the over-voltage pulse of the opening switch. The simulation results indicate that this zero-current opening circuit is feasible and has potential applications for high-energy systems in the future electromagnetic launcher. [ABSTRACT FROM PUBLISHER]

Based on the features of large heating power per unit volume and small cooling surface area, the thermal management is one of the key technologies and plays a significant role for the pulsed inductor. A mathematical model that describes the heat transfer and thermal accumulation processes with the operating condition of periodic pulse loading for the pulsed inductor has been developed and validated in this paper, and the model results show a fine accuracy as compared with the test data. In addition, a computer code has been implemented to simulate the thermal accumulation and performance of natural cooling with different operating conditions (as the various of pulse voltage, pulse spacing, and pulse duration). The results show that the pulse voltage, pulse spacing, and pulse duration are the focus factors to the thermal accumulation for the pulsed inductor, and the effect of the natural cooling by surface area of the inductor is poor under the periodic pulse loading. [ABSTRACT FROM PUBLISHER]

Matching a pulse source to a plasma load is one of the main challenges to overcome to maximize the full potential of pulsed discharges for air purification applications. In this paper, we propose experiments that investigate the matching of a nanosecond pulse source to a corona plasma reactor that is aided by a high voltage on a tertiary electrode. The corona plasma reactor is a wire-cylinder reactor, as is commonly used in pulsed power plasmas. A tertiary electrode is situated on a dielectric layer against the cylinder of the reactor. On this tertiary electrode, we can apply a pulsed RF or dc voltage to provide an additional plasma and bias voltage in the corona plasma reactor. The pulse source that energizes the main corona plasma is the nanosecond pulse source of Kumamoto University, Japan. In this paper, we show the results of experiments with a dc voltage on the tertiary electrode. We varied the amplitude of the pulsed voltage as well as the dc voltage and investigated their effect on the corona plasma with energy and ozone measurements. The results show that the matching to the reactor increases with increasing dc voltages. However, the matching effect decreases with higher repetition rates. Furthermore, ozone measurements confirmed that a better matching also results in a higher ozone production, but in a lower ozone production energy yield. [ABSTRACT FROM PUBLISHER]

This paper is to experimentally investigate the effect of plasma-activated gas on the characteristics of a laminar lifted nonpremixed jet flame in a coflow stream. A coaxial dielectric-barrier discharge is employed to activate fuel (C3H8) and oxidizer, respectively. It is shown that an enhancement of 12% and 50% in the liftoff velocity is observed for oxidizer and fuel activation, respectively. With the addition of O3 (1650 ppm) by oxidizer activation, the flame liftoff height is continuously decreased and the blowout velocity is extended. In contrast, a larger liftoff height, accompanied with a smaller blowout velocity, exhibits for flames with fuel activation. The inconsistent effect of fuel activation on the flame liftoff is presumably a contribution of the gas expansion, the conversion rate, and the corresponding product selectivity. The gas expansion is due to the fuel activation that produces lighter hydrocarbons than propane. The conversion rate and the H2 and CH4 selectivities are found to be associated with the plasma energy density. The flame propagation can be greatly enhanced to produce a nozzle-attached flame when the plasma energy density is high enough to effectively decompose C3H8 into H2. Nevertheless, a decrease in plasma energy is more sufficient for the cleavage of C–C bonds, resulting in a significant decrease in H2 selectivity, but a nearly unaltered CH4 selectivity. The reduced conversion due to the lower plasma energy, along with the gas expansion, produces a lifted flame with a larger liftoff height than the nonactivated flame. [ABSTRACT FROM AUTHOR]

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

Nonequilibrium plasma is an effective and one of versatile advanced oxidation process due to the formation of reactive species such as hydroxyl radicals, oxygen atom, and hydroperoxyl radicals. In pulsed discharge, free electrons gain energy from an imposed electric field and lose this energy through collisions with neutral gas/liquid molecules. The transfer of energy to the molecules leads to the formation of a variety of new species including atoms, free radicals, and ions. These products are all active chemically, and in our case, we measure the amount of hydroxyl radicals generated in the reactor and also the amount of escaped ozone generated in the reactor and decolorized indigo reagent in a graduated cylinder (GC). In this paper, we used oxygen and argon gases in various flow rate and mixed ratios to feed a gaseous phase in a water spraying droplet reactor. The experimental results indicated that the oxygen and O2/Ar mixture flow rates in spraying reactor have an effect on both hydroxyl radical generation and decolorization of indigo reagent solution. Argon gas discharge has less effect on hydroxyl radical production compared to the oxygen gas discharge with the same flow rates and no effect on the decolorization of indigo reagent solution in GC. We obtained remarkable results on both hydroxyl radical generation rate and decolorization efficiency of indigo reagent solution when we discharged with the mixture of O2/Ar “especially when the ratio has more oxygen than argon gas.” Hence, the presence of oxygen in the water spray plasma discharge is very important as it influence the generation of reactive species such as O atoms and ozone in the gas and liquid phase, which can react directly with organic contaminants and also contribute to more production of hydroxyl radicals in the aqueous phase. [ABSTRACT FROM AUTHOR]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

For the electromagnetic rail launcher, the parameters variation has obvious effect on the dynamic performance and efficiency. This paper constructs the system simulation model of the electromagnetic rail launcher by using of Simulink software, and then analyzes the influences on the system dynamic performance for main devices. Based on the parameters and large current condition, the launching efficiency model is constructed, and the energy distribution characteristics are obtained. The loss of rail, armature, and feeder equipment is 38.7%, and the loss of arc extinguishing equipment is about 4.76%, so the heat loss is about 43.46% of total loss. When considering that the other loss is 33.37%, the system energy efficiency is 23.17%. Based on the design of the small prototype, the energy loss characteristics of the full prototype in launch rail and its temperature features are discussed in detail. The peak temperature is 276 °C after 11 continuous shots with converting coefficient being 5000 W/( \textm^2\cdot \text K ), and it can decrease 58 °C if the better convection boundary condition is achieved, which means the rail can meet the requirement of the thermal management. [ABSTRACT FROM PUBLISHER]

It is important to analyze the electromagnetic coupling characteristics in pulsed power supply (PPS) during the design, and electromagnetic force analysis is becoming more and more important with the development of large capacity and miniaturization of PPS module. In this paper, the magnetic force on the metal structure affected by the pulsed electromagnetic field of the reactor is analyzed and calculated by the means of the finite-element code ANSYS. The results show that the electromagnetic force on the metal structure near the reactor is about ten times that of other parts. The eddy current distribution is calculated by the electromagnetic coupling simulation while the stress on the metal frame is analyzed by the electromagnetic structure coupling simulation. The breaking point assumed to be the weakest point in the structure. The weakest point in the structure is indicated by structural stress simulation. The electromagnetic force is reduced by cutting off the main induce loop through simulation, and the eddy current is measured by experiments. [ABSTRACT FROM PUBLISHER]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

The role of irreversible electroporation using pulsed electric field is to generate high-voltage (HV) pulses with a predefined magnitude and duration. These HV pulses are applied to the treatment chamber until decontamination of the sample is completed. In this paper, a new topology for HV rectangular pulse generation for water disinfection applications is introduced. The proposed topology has four arms comprised of series-connected half bridge modular multilevel converter cells. The rectangular pulse characteristics can be controlled via the software controller without any physical changes in power topology. The converter is capable of generating both bipolar and monopolar HV pulses with microsecond pulse durations at high a frequency rate with different characteristics. Hence, the proposed topology provides flexibility by software control, along with hardware modularity, scalability, and redundancy. Moreover, a cell’s capacitance is relatively small, which drastically reduces the converter footprint. The adopted charging and discharging process of the cell capacitors in this topology eliminate the need of any voltage measurements or complex control for cell-capacitors voltage balance. Consequently, continuity of converter operation is assured under cell malfunction. In this paper, analysis and cell-capacitor sizing of the proposed topology are detailed. Converter operation is verified using MATLAB/Simulink simulation and scaled experimentation. [ABSTRACT FROM AUTHOR]

We are studying the treatment method that injects the droplets of waste water into pulsed discharge plasma generating by a pulsed power technology as an advanced water treatment technique. The active species, such as ozone and OH radical that have high oxidizing power, are generated in the place injecting the droplets by the discharge, and can be effectively used to decompose the organic compounds that are difficult to decompose. However, there has been few investigation of interaction between the pulse streamer discharge and the droplet in a configuration of a treatment reactor. In addition, a propagation route of pulse streamer discharge has been few investigated in the space putting the droplets in the configuration of the treatment reactor. In this paper, the propagation route of the pulse streamer discharge in the space with the droplets of water has been investigated at the configuration using the wire electrode. In addition, the influence of the droplets to the discharge has been investigated. From results, it was shown that the pulse streamer discharge propagated on the surface of the droplet. Primary streamers mainly occurred at the positions of the droplets. The propagation lengths of secondary streamer in air with the droplets were shorter than that without the droplets. The existence of the droplets prevents the propagation of the secondary streamer. [ABSTRACT FROM AUTHOR]

The slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit is a widely used topology in inductive pulse power supply. Therefore, it is important to understand the relationship between the STRETCH meat grinder performances and the inductor parameters when improving the system performance and designing the inductor. From the perspective of inductor designing, this paper uses four indicators to present the STRETCH meat grinder performances, i.e., the charging current, the current amplification, the inductor energy density, and the discharge efficiency, and uses two indicators to present the inductor parameters, i.e., the total inductance and the ratio of the inductance L1 to L2 . First, the meanings of the indicators are explained or defined. Second, simulations and experiments are carried out, respectively, to analyze the trends of the four performance indicators along with the changes of two parameters indicators. Finally, both simulation and experiment results show that the increase of the total inductance leads to the decrease of the charging current and the discharge efficiency; moreover, the increase of the ratio of the inductor L1 to L2 leads to the increase of the current amplification and the discharge efficiency, but causes the decrease of the inductor energy density. [ABSTRACT FROM AUTHOR]