Search

In recent years, all-solid-state high-voltage pulse generators have been widely used in irreversible electroporation for tumor ablation technology. However, high voltage may cause the breakdown of loads that leads to short circuits. The short circuit of loads will generate high short-circuit currents that will affect the performance of semiconductor switches. To improve the reliability and lifetime of solid-state pulse generators, a passive synchronous isolated gate drive circuit with short-circuit protection based on decreasing the gate–source voltage is proposed in this article. To verify the overcurrent protection during the breakdown of loads, a solid-state Marx generator prototype using the drive circuit was built and tests were carried out. The experimental results show that the 205-A short-circuit current was clamped with 90 A in less than 500 ns, while the transient voltage can be neglected. Besides, the response time, the maximum transient voltage, and the maximum current amplitude can all be adjusted. [ABSTRACT FROM AUTHOR]

The results of comparative studies of two compact generators of nanosecond high-voltage pulses are presented. Both generators include an opening switch in the form of a block of drift step-recovery diodes (DSRDs) and a closing switch in the form of a block of shock-ionized dynistors (SIDs). The generators are designed according to two different schemes, but they have similar parameters of the output pulses on a load of $50~\Omega $ : the amplitude of the output voltage is ~ 30 kV, its rise time is ~ 3 ns, and the output energy is ~ 0.4 J. It is shown that it is possible to increase the output voltage and output energy of the generators. [ABSTRACT FROM AUTHOR]

The development of pulsed power puts forward new requirements on volume and weight of generators. To develop a compact and lightweight high-voltage pulse generator, this work proposed a new modular pulse forming topology with high voltage gain and a reduced number of energy storage capacitors. The topology is realized by charging a set of capacitors cyclically step-by-step and discharging repetitively in series. A voltage gain of $2^{n-1}$ can be achieved with $2n\,+\,1$ all-solid-state switches, $n$ fast recovery diodes, and n capacitors. An experimental prototype built around five capacitors generates high-voltage pulses with adjustable voltage level, pulse frequency, and pulsewidth. Meanwhile, it is verified that the prototype has a certain capacity with a capacitive load. [ABSTRACT FROM AUTHOR]

A 4-MV self-triggered switch based on ultraviolet (UV) illumination technology is designed and tested under approximate 800-ns rise time pulse voltage. The switch is composed of five sections in series, and each section comprises an UV-illuminating gap (UV gap) and a main gap. The voltage charged on the UV gap is obtained by a resistance–capacitance coupling circuit, which enhances synchronization with the main gap voltage. The gap distance of the 4-MV switch is determined according to the performance of the same type of switch under a shorter pulse (about 300 ns), while the characteristics of the gap under 800-ns pulse voltage is still unclear. The experimental results show that low jitter breakdown of the switch can be realized effectively when two UV gaps are functioning. The breakdown jitter percentage achieves less than 1.55% within the range of 1.0–3.2 MV. When the working scope is narrowed down to 1.4–2.1 MV, the breakdown jitter is less than 1%. [ABSTRACT FROM AUTHOR]

Long pulse gas lasers utilizing double-discharge circuits are different from the single-short pulse gas lasers in that they do not require all of the desired energy to be deposited into the peaking capacitors prior to ignition of the main gap. Instead, the majority of the energy is held in another capacitor that is then discharged in the form of a longer duration discharge pulse output compared with that of single-short pulse lasers. Extended stability of the discharge is typically achieved by igniting the main gap discharge at higher ignition voltages. Several double-discharge circuit topologies exist in the literature. However, each topology has its own disadvantages primarily centered around the components needed and the resulting complexity. In this article we introduce the application of the new hybrid circuit pulsed power topology as a double-discharge circuit with high ignition voltages. The hybrid circuit pulsed power topology was originally published by the authors of this article in their previous publication titled “A New Hybrid Pulsed Power Circuit Topology for Gas Laser Applications.” The advantage of the hybrid circuit as a double-discharge circuit is that it does not require any special device [e.g., semiconductor opening switch (SOS) diode] and can use commonly available components. [ABSTRACT FROM AUTHOR]

Marx generators are widely used to produce transient high-voltage pulses. The evolution of semiconductor devices and power electronics concepts promotes the development of solid-state Marx generators (SSMGs) and enables them with flexible pulse modulation ability. First, this article sorts out the evolution of SSMGs topologies chronologically. We can see that how the energy efficiency of SSMGs is considerably improved by replacing resistors with diodes and switches and how square-wave pulses are generated by SSMGs based on half-bridge structures. Unipolar and bipolar pulses can be easily produced with different SSMGs. Second, we discuss the influence of rated voltage and rated power of present semiconductor switches on the performances of SSMGs since switches are the key components in pulse generators. To reduce the size and weight of SSMGs, metal–oxide–semiconductor field-effect transistors (MOSFETs) and insulated gate bipolar transistors (IGBTs) with small packages are preferable. Third, synchronous isolated driving of switches as the crucial technique in SSMGs is introduced. Different methods of providing synchronous signals and isolated power to various stages in SSMGs are illustrated. Fourth, the performance including load capacity, droop compensation, waveform modulation, and self-triggering of SSMGs is discussed. In the end, the developing trend of SSMGs is given. [ABSTRACT FROM AUTHOR]

C5-fluoroketone (CF3C(O)CF(CF3)2, abbreviated C5-FK) and C4-fluoronitrile [(CF3)2CFCN, abbreviated C4-FN] mixed with background gases such as carbon dioxide, oxygen, or air are used as alternatives to SF6 as the insulating and switching medium in high voltage gas insulated switchgear (GIS) due to their good switching and dielectric insulation performance and comparably low global warming potential (GWP). Like SF6, C5-FK and C4-FN are chemically stable inside electrical equipment and non-flammable. Like most complex molecules, they decompose exothermically when exposed to sufficiently high temperatures and do not recombine after decomposing. In this work, we use a custom-built test device to experimentally investigate the conditions and gas compositions under which a decomposition reaction can proceed to completion in C5-FK- and C4-FN-based gas mixtures after being initiated by an electric arc. We also present the related theory. The results show that, for properly selected mixtures, even under extreme failure conditions—internal arc faults—complete decomposition of the C5-FK or C4-FN does not occur. [ABSTRACT FROM AUTHOR]

This article describes the performance of a multi-gap, multichannel (MGMC) spark gap switch, evaluated numerically and experimentally, to achieve multichanneling using a relatively low-magnitude trigger pulse. First, an electrostatic analysis of the switch geometry was carried out using COMSOL Multiphysics 5.5 to determine the electric field distribution during high-voltage hold-off before triggering and to determine the coupling parameters between trigger and other intermediate electrodes of the switch. Second, a circuit model was developed in PSpice Lite 16.6 for predicting the process of channel formation and its influence on adjacent channels. Based on the simulation results obtained, a six-gap, eight-channel, planar MGMC switch operating in air has been designed and developed. The developed switch was, then, incorporated into a compact experimental setup to experimentally evaluate various switch parameters such as inductance, switching delay, jitter, and closing time when triggered using a negative-polarity trigger pulse of magnitude −40 kV, generated using a compact, in-house developed trigger generator. In contrast to most of the reported MGMC switches that use complicated Marx-based generators to produce ≥120-kV trigger pulses for multichannel formation, the experimental results, thus obtained, report comparable switch performance using a low-magnitude (−40 kV) trigger pulse. In addition, framing and streak camera images taken during the current discharge indicate the presence of ~6 luminous channels. In addition, short-circuit experiments for estimating switch inductance by consecutively shorting one or more channels also indicate multichanneling in the switch using a low-magnitude trigger pulse. [ABSTRACT FROM AUTHOR]