Search

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

This paper is aimed at finding the effect of varying inductive energy storage systems’ (IESSs) inductance on resistance of an electrically exploded conductor-based opening switch and profile of current transferred into load, which has not yet been fully understood. Based on experimental results obtained, it is observed that when the inductance of IESS is varied, the magnitude of load current changes so as to conform to the magnetic flux conservation law but its rise time remains unchanged. Resistance of the opening switch and energy deposited in it has been estimated using recorded voltage and current waveforms. It has been found that with increasing inductance of IESS, the resistance of switch increases, whereas energy deposited in it decreases. Using these estimated values of energy, a possible explanation of observed behavior in resistance is presented. Effect of a mismatch between the inductance of IESS and load is seen to only affect the energy transfer efficiency or magnitude of load current but not its rise time emphasizing the novel finding that for a given load, the rise time of load current is independent of the inductance of IESS. [ABSTRACT FROM AUTHOR]

Paralleled pulse-forming units (PFUs) with different triggering delays might be a paramagnetic way for generating flat-topped current wave for electromagnetic launch. Many researchers have reported that multiple capacitive storage PFUs were implemented such current waves in laboratories. However, due to its low energy density, the applications of the capacitive pulsed-power supplies are limited. Since the inductor has advantages in energy density, the inductor pulsed-power supply becomes one of the hottest topics recently. The slow transfer of energy through capacitive hybrid meat grinder with inverse current commutation with semiconductor devices proposed by Tsinghua University has demonstrated its advantage and applicability recently. Using this kind of topology, this paper proposes the design of an inductive storage PFU with a stored energy of 100-kJ. The maximum load current reaches to 50 kA and its pulsewidth is at least 5 ms. The optimized inductive storage PFU shows superiority in contrast to the capacitive storage PFU with the same energy. This paper offers the theoretical analysis and the testing foundation for investigating the inductor pulsed-power supply with higher energy. [ABSTRACT FROM PUBLISHER]

Slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, which was proposed by the Institute for Advanced Technology, added a capacitor into the traditional meat grinder circuit. Even though its energy density is slightly less than the corresponding pure inductance system, it can reduce the voltage across the opening switch and maintain the high multiplication factor of the opening current. The performance of the STRETCH meat grinder circuit depends on multiple parameters. The inductance ratio ( n=L1 / L2) and the capacitance (C) are the two vital factors, which have a crucial influence on the system performance, such as the voltage over the opening switch ( V_{\rm Sopm}) , the current multiplication factor ( m$ ), and the ratio of the maximum capacitive energy over the total inductive energy ( $\eta )$ . Thorough studies have been carried out in this paper on the relationship between the above two factors and the three performance criteria. This paper also discusses and analyzes the chosen of the key parameters ( $n$ and $C$ ) for a single-stage STRETCH meat grinder with 2-mH total inductance, which is made up of two serial coils with 0.95 coupling factor. The opening current of the main switch is 1 kA, which constitutes a 1-kJ inductive pulsed-power supply. It fully takes the advantage of the STRETCH meat grinder topology, intensifies the study of the inductive pulsed-power supply with higher energies, and is easy to be utilized for practical application. [ABSTRACT FROM PUBLISHER]

The superconducting inductive pulsed-power supply (SPPS) circuit consists of a high-temperature superconducting pulsed-power transformer (HTSPPT) and an auxiliary capacitor. The electrical losses and the power of the primary source can be cut down with the superconducting inductive energy storage. Although its energy density is slightly less than a purely superconducting inductive system, it can reduce the maximum voltage of the opening switch by the capacitor and achieve a high degree of current amplification factor. However, during the discharge process, the magnetic leakage flux energy stored in the primary of the HTSPPT requires the capacitor to have a certain capacity. The higher the ratio of the capacitive stored energy over the total inductive stored energy, the more the dominant position of inductive energy storage reduces. The current amplification factor ( \gamma ), the maximum voltage of the opening switch ( V_{S\max } ), and the ratio of capacitive stored energy ( \eta ) are the three main properties of the SPPS circuit, which depends on several intertwined critical parameters, such as the inductance ratio n = L2 /( L2+LL ) and the capacitance ( $C_{{\mathbf {1}}}$ ). This paper studies the influence of the critical parameters on the main circuit performance with a 1-kJ SPPS system. The detailed selection method of the critical parameters for the specific system is also discussed with a coupling coefficient of 0.95. Such a system is easy to be utilized for the basic experimental study of a small railgun. [ABSTRACT FROM PUBLISHER]

This paper describes a compact high storage density inductive–capacitive storage module. The module is based on high-power opening switches using inverse current commutation with semiconductor devices commutation principle and a high storage density Brooks inductor. These opening switches, being able to switch-OFF pulse currents up to 14.5 kA by the counter-current subcircuit, make use of the general property of a standard high-power thyristors impedance transition from closing state to blocking state. The experimental results show that with the primary capacitor and counter-current commutation subcircuit charged voltage 3 and 2.5 kV, respectively, the charged current of the Brooks-type inductor is about 14.5 kA, with a charged time of about 4.5 ms. The output peak current of the inductive storage module is about 21 kA. The total stored energy is about 54.9 kJ while the energy density of the inductor is approximately 6.69 MJ/ \textm^3 , which is not including the primary storage and commutation unit. [ABSTRACT FROM PUBLISHER]

This paper provides analysis of experiments aimed at defining the capabilities of plasma opening switch (POS) for energy transfer to a load of inductance comparable with the inductance of the energy store vacuum section. The analysis is performed using the substantiated technique that allows quantitative estimation of the POS efficiency. Under the same conditions with a conduction current of ∼1 MA and POS voltage of ∼1 MV, the energy transferred to the load depends strongly on the transmission line design. When the electrode gap in the line is ∼1 cm, the energy delivered to the load is ∼40 kJ. Increasing the gap to ∼4-cm increases this energy to ∼100 kJ. [ABSTRACT FROM PUBLISHER]

This paper details the testing of a commercially available gate turn-off thyristor (GTO) for application in inductive-store power supplies. GTOs have been used as a component of inductive-store systems directly and as part of compound switches. These GTOs are generally available commercially and typically have extensive datasheets. However, the inductive-store application differs significantly from conventional switching applications, which significantly reduces the utility of the datasheets; GTOs are typically used at 100–1000 Hz in a fairly continuous manner, whereas in an inductive-store system, a GTO may be conducting for a relatively long time before doing a single turn off. [ABSTRACT FROM PUBLISHER]