Search

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

Bipolar junction transistors (BJTs) have been widely studied and used in nanosecond high-voltage pulse generators due to the advantages of fast switching speed and high repetitive frequency. Usually the Marx-type circuit is used to raise the peak value of output pulses. In this paper, a traditional BJT-Marx circuit using charging resistors is analyzed theoretically and experimentally. Based on the results, the structure of a circuit is changed to decrease the isolation voltage across the resistors, and diodes are used to replace charging resistors to block capacitors discharging to resistors. Experimental results showed that the three Marx generators proposed in this paper output pulses with higher voltage amplitude, and the last improved circuit outputs pulses with faster fall times at a higher efficiency. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

Repetitive high-voltage square pulses are of great importance for producing long-pulse electron beams and high-power microwaves. One of possible technologies for the generation of such pulses is a Marx generator using pulse forming network (PFN) stages, often combined with a pulse sharpening technique to reduce the rise time to a few nanoseconds (peaking stage). This paper presents an innovative design, named the “zigzag design,” for the optimization of the compactness and of the rise time of 400-kV–85-ns PFN-Marx. Thanks to this design, the 16 stages of this generator, which delivers an open circuit output voltage of 720 kV, fit in a 650-mm length. For a slightly overmatched load ($Z_{\mathrm {load}} = 100 ~\Omega$), the output voltage reaches 400 kV with a rise time as less as 5 ns. The inductance reduction associated with the innovative zigzag design, which allows this sharp rise time with no need for a peaking stage, is described. The 85-ns plateau duration of the pulse is given by the PFN construction of each stage, which is based on six ceramic capacitors (2.1 nF–45 kV) connected within a strip line. The 16 PFN stages are housed in a 360-mm diameter gas pressurized vessel. Burst mode operation for a duration of 10 s at a pulse repetition frequency of 100 Hz is reported, for a resistive load and for the electron beam diode of a X-band relativistic backward-wave oscillator (BWO). To reach further compactness, the BWO system is integrated on side of the generator vessel and a U-shaped gas pressurized line connects both systems through a compact conical vacuum insulator. [ABSTRACT FROM AUTHOR]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]

This paper describes the construction and experimental tests of a 12-kV high-voltage high-action generator based on reverse-switching dynistor (RSD) assembly. The main RSD unit consists of seven 76-mm-diameter dynistor pieces connected in series with a blocking voltage of about 2.4 kV, a magnetic switch based on a 1K101 amorphous alloy core, the trigger system based on a saturable transformer, and a 16-mm RSD assembly; the trigger current could reach 2 kA in amplitude with 1-\mu\s duration under 10 kV. The working voltage rate of this RSD unit is about 8–12 kV. Experiment on a 2.2-mF capacitor test bed under 12 kV working voltage, the switch current amplitude reached 150 kA with 300-\mu\s duration; the transferred charge is about 26.5 C and the action is 2.94 \MA^2\s, respectively. [ABSTRACT FROM AUTHOR]