Search

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]

The acceleration grid power supply (AGPS) is an important part of the neutral beam injector (NBI) system. With the increase in NBI power, the requirement for output voltage of the AGPS is becoming higher and higher, even reaching to 1000 kV. As the inverter-type high voltage power supply uses inverters located at the lower voltage side to regulate and cut off the output voltage, it is very suitable for high-voltage applications. The proposed scheme for the AGPS of the International Thermonuclear Experimental Reactor (ITER) NBI system comprises five stages, where each stage has an inverter-type power supply with an output voltage of 200 kV. This paper investigates the inverter-type power supply based on neutral point clamped three-phase three-level (TPTL) inverter and three-phase step-up transformer, which is equivalent to an insulated TPTL dc–dc converter connected with a dual dc link. In order to design a preferable controller for the inverter-type power supply, the topology and principles of the TPTL dc–dc converter with duty cycle modulation have been analyzed. It indicates that only when the converter operates at a large duty cycle, the output voltage ripple can be limited to ±5%. Hence, the small signal model of the converter at a duty cycle larger than 2/3 is established. Following the mathematical model, a single-loop PID controller has been designed and a 400 V/6 A prototype has been built. Simulation and experimental results verify the correctness of the theoretical analysis. The system achieves a lower output voltage ripple and fast dynamic response. [ABSTRACT FROM AUTHOR]

This paper describes the design and implementation of a three-phase resonant converter with low ripple and high control accuracy. Based on a three-phase LCC-type resonant converter—which has advantages of low ripple, high-efficiency, and high-power density compared with a single-phase converter—a high-voltage power supply with low ripple (<0.1%) was designed. In addition to the general merits of an LCC-type resonant converter operating at continuous conduction mode—including soft switching, low conduction loss, and current source characteristics—the proposed scheme uses only one phase under a light-load condition by having different leg designs of the gate drive circuit and snubber parameters. This allows the design to overcome the operational constraints of the general LCC-type resonant converter. The distinctive design of the three-phase converter structure provides high efficiency and low ripple not only during rated operation, but also under light-load conditions. In order to analyze the high performance of the proposed scheme from no load to rated load, a PSPICE simulation was carried out. Comparison results with a conventional LCC-type resonant converter based on a single-phase structure are analyzed from the viewpoints of output ripple, losses, and operable load range. Using the proposed converter, a 20-kV, 20-kW high-voltage dc power supply design and implementation was presented with a superior gate drive circuit. Finally, the superiority of the proposed converter was verified through a simulation and experimental results. It was experimentally confirmed that the developed power supply achieves high performance in terms of efficiency (98%), operable load range (0.5–20 kV), and low ripple (0.05%), with a high power density. [ABSTRACT FROM PUBLISHER]