Search

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

A novel circuit with the better performance for the inductive pulsed power supplies in the electromagnetic launch system is proposed in this paper, namely, the meat grinder with capacitive pulse forming unit (CPFU). Its working process is qualitatively analyzed stage by stage. Its practical feasibility is verified through a 7.5-kJ experiment. From the perspectives of circuit structure and working principle, this circuit can be regarded as the combination of a meat grinder and a CPFU. Compared with its preceding circuits, this circuit possesses following advantages: 1) the self-recovery of the capacitor precharged voltage can easily be achieved, which is conducive to continuous operations of the whole circuit and 2) the waveforms of the inductor currents contain no capacitive components, which can promote the energy storage density of the inductors. [ABSTRACT FROM PUBLISHER]

The meat grinder is a basic circuit for inductive pulsed-power supply (IPPS). Based on meat grinder, the Institute of Advanced Technology proposed a circuit called the slow transfer of energy through capacitive hybrid (STRETCH) meat grinder, in which an Integrated Gate Commutated Thyristors (IGCT) is selected as the main switch. Tsinghua University proposed the STRETCH meat grinder with inverse current commutation with semiconductor devices (ICCOS) in which the main switch is replaced by a thyristor and the ICCOS subcircuit is introduced to turn off the main switch. To reduce the opening switch voltage and increase the current turning-off capacity for IPPS, this paper presents a novel circuit topology named the meat grinder with self-charged capacitor and thyristors (SECTs). The key idea of the SECT topology is to turn off the primary current by the energy transfer capacitor, which is precharged. The meat grinder with SECT has larger capacity than the STRETCH meat grinder because it replaces the IGCT with a thyristor and is simpler than the STRETCH meat grinder with ICCOS because it only needs one capacitor. The suggested circuit is more suitable for IPPS module with high energy density. Simulation and experiment have been carried out to validate the circuit. [ABSTRACT FROM PUBLISHER]