Search

Normally, a three-electrode spark–gap switch is controlled by the application of an external trigger impulse. In this paper, a novel self-breakdown sharpening switch based on the three-electrode spark–gap switch is proposed. However, in this paper, the trigger electrode is connected to ground through a resistor, with the prespark between the trigger and the main electrodes providing the electrons and ions that initiate conduction of the main gap. A prototype sharpening switch with a breakdown voltage of 116.0 kV \pm 1.0 kV and a breakdown time of 3.396\ \mu\s\pm 0.036 \ \mu\s is described. When compared with a conventional two-electrode spark–gap sharpening switch, the novel sharpening switch has both a more stable breakdown voltage and lower jitter, and the dc breakdown and impulse breakdown characteristics of the two types of switches are presented and compared. When the impedance of the resistor connected to the trigger electrode is high, it is demonstrated that both the value of this resistor and also the type of load have little effect on the characteristics of the novel switch. However, the breakdown voltage of the novel sharpening switch was found to be sensitive to the rise time of the input pulse from the trigger generator. The prototype sharpening switch has a lifetime at least 20 000 shots and is now in use in a major pulsed power conditioning system. [ABSTRACT FROM PUBLISHER]

A repetitive 0.6 MV, 10 GW Tesla-driven Blumlein pulsed power generator, with an overall energy efficiency in excess of 90%, has been designed, manufactured and demonstrated by the Pulsed Power Group at Loughborough University. This paper describes the application of various numerical techniques used to design a successful generator, such as filamentary modeling and electrostatic and transient circuit analysis. All the major parameters of both the Tesla transformer and the Blumlein pulse-forming line were determined, enabling accurate modeling of the overall unit to be performed. The wide-bandwidth embedded sensors used to monitor the dynamic characteristics of the overall system are also presented. Experimental results obtained during this major experimental program are compared with theoretical predictions and the way ahead toward generating faster output voltage impulses is considered. [ABSTRACT FROM PUBLISHER]

SPHINX is a microsecond linear transformer driver located at Atomic Energy Comission (CEA) Gramat (France), which can deliver a current pulse of 6 MA within 800 ns in a Z -pinch load. Using the concept of the dynamic load current multiplier (DLCM), which was proposed by Chuvatin, we expect to increase the load current above 6 MA, while decreasing its rise time to \sim300 ns. The DLCM developed by the CEA Gramat and International Technologies for High Pulsed Power (ITHPP) is a compact system made up of concentric electrodes (autotransformer), a dynamic flux extruder (cylindrical wire array), a vacuum convolute (eight post-hole rods), and a closing switch (compact vacuum surface switch). The latter is a key component of the system, which is used to prevent the current from flowing into the load until the inductance builds up due to the implosion of the wire array. This paper presents the design and testing of the DLCM surface switch, resulting from both electrostatic simulations and experiments on the SPHINX generator. These studies, carried out either with or without load (open circuit), were valuable for a first experimental evaluation of the DLCM scheme in a microsecond regime and provided detailed information on the surface switch behavior. [ABSTRACT FROM AUTHOR]

Switching time jitter is an important property to consider when selecting closing switches for pulsed-power systems. The corona-stabilized switch (CSS) is identified as an interest for low-jitter systems, in particular for systems where a high-repetition rate is required. In this paper, a commercial CSS is studied and its operating conditions are determined. [ABSTRACT FROM AUTHOR]

Starting from the updated requirements of an advanced laser system, a switch–trigger system for a 2.0-MJ pulsed power supply (PPS) module is developed. This paper discusses the design, construction, and testing of this switch–trigger system. The two-electrode construction for the spark gap switch is selected because of its superiority in terms of long working life, high peak currents, and fast rise time of currents. The trigger generator based on resonant charging of a pulse transformer is constructed. A magnetic isolator and a pressure controller are the auxiliary equipment of this system. In the section based on mathematical principles, the equations of the lifetime and stability of this spark gap switch with graphite electrodes are given. These expressions can be regarded as the design basis of the same type of switch. As for the trigger generator, the analysis states that an appropriate ratio can be obtained when using the resonant charging based on a core-type pulse transformer. The charging time is dependent on the leakage inductance and the capacitance of the primary and secondary capacitors. Extensive testing proves the operating parameters of the switches and the trigger generator. The measured discharge current waveform of the 2.0-MJ capacitive PPS module is demonstrated to be over 500 kA peak current and 500 \mus pulse width. The life test proves that the switch–trigger system can support more than 200 kC transfer charge. By replacing the electrodes, the lifetime of this switch can be extended furthrer. [ABSTRACT FROM PUBLISHER]