Search

This paper has introduced two important indexes, turn-off surge voltage (TSV) on power switch and peak positive pole potential (PPPP) of storage batteries, which can be used to evaluate switching transient process of high-voltage energy storage system. Research on them is of great significance to power switch choice and high-voltage isolation design in engineering applications. Power switch response process at the turning off moment and transient process in freewheel stage have been analyzed by the established small-signal model of single power switch; then, a power switch test platform for hybrid energy storage system was built to verify it. Taking pulsed-power supply charging device with a novel inductor of low resistance and high inductance as a research object, this paper has analyzed dynamic process of the TSV and the PPPP at the turning off moment through establishing state space model of the whole system. Comparison shows that the numerical curves match the simulated curves well. Finally, the exactness of the employed model has been further verified in two pulse capacitor charging experiments. [ABSTRACT FROM AUTHOR]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposed the use of a ringer, a self-switched inductive storage system, for applications involving reluctance accelerators, a kind of electromagnetic launcher, and compatible with applications where portability is a requirement. There will be shown three different useful approximations for the analysis of the ringer, employed as a power source for a reluctance accelerator. First, it described the equations governing the que behavior of an ideal unloaded ringer, and then the equations for the ringer with an uncoupled inductive load, and ultimately a Lagrangian model for the ringer as an inductive power source for a reluctance accelerator, capable to make predictions about the currents through the circuits and the exit speed of the projectile for a given firing. The accuracy of the predictions made with the third approximation, the Lagrangian model, was tested experimentally. [ABSTRACT FROM AUTHOR]

This paper is aimed at finding the effect of varying inductive energy storage systems’ (IESSs) inductance on resistance of an electrically exploded conductor-based opening switch and profile of current transferred into load, which has not yet been fully understood. Based on experimental results obtained, it is observed that when the inductance of IESS is varied, the magnitude of load current changes so as to conform to the magnetic flux conservation law but its rise time remains unchanged. Resistance of the opening switch and energy deposited in it has been estimated using recorded voltage and current waveforms. It has been found that with increasing inductance of IESS, the resistance of switch increases, whereas energy deposited in it decreases. Using these estimated values of energy, a possible explanation of observed behavior in resistance is presented. Effect of a mismatch between the inductance of IESS and load is seen to only affect the energy transfer efficiency or magnitude of load current but not its rise time emphasizing the novel finding that for a given load, the rise time of load current is independent of the inductance of IESS. [ABSTRACT FROM AUTHOR]

Recently, inductive energy storage systems have attracted interests due to high energy densities. The high-temperature superconducting pulsed-power supply (HTSPPS) is one inductive PS topology for electromagnetic launching system. The topology can achieve a high amplitude load current and cut down the electrical losses due to the zero resistance characteristic of superconducting inductors. However, in this topology, the integrated gated commuted thyristor is used as a switch and cannot withstand high current, which limits the expansion of the system. Besides, it has significant current amplification ability as a single unit, but one module cannot provide sufficient amplitude and appropriate pulsewidth for the load current of the electromagnetic launching. In this paper, by applying the principle of inverse current commutation with semiconductor devices (ICCOS) in the HTSPPS, a novel circuit topology called HTSPPS with ICCOS is presented. This topology is analyzed and the multiple modules system is established. Simulation results show that the HTSPPS with ICCOS exceeds the current limitations of the original one and ensures the reliable cutting off of the main switch. It has potential applications in the future of high-energy systems while reducing the cost greatly. By asynchronous cooperative triggered discharge of the multiple HTSPPS with ICCOS modules in parallel, the appropriate amplitude and flat shape current of the load can be achieved through the careful design of the trigger time. [ABSTRACT FROM AUTHOR]

Paralleled pulse-forming units (PFUs) with different triggering delays might be a paramagnetic way for generating flat-topped current wave for electromagnetic launch. Many researchers have reported that multiple capacitive storage PFUs were implemented such current waves in laboratories. However, due to its low energy density, the applications of the capacitive pulsed-power supplies are limited. Since the inductor has advantages in energy density, the inductor pulsed-power supply becomes one of the hottest topics recently. The slow transfer of energy through capacitive hybrid meat grinder with inverse current commutation with semiconductor devices proposed by Tsinghua University has demonstrated its advantage and applicability recently. Using this kind of topology, this paper proposes the design of an inductive storage PFU with a stored energy of 100-kJ. The maximum load current reaches to 50 kA and its pulsewidth is at least 5 ms. The optimized inductive storage PFU shows superiority in contrast to the capacitive storage PFU with the same energy. This paper offers the theoretical analysis and the testing foundation for investigating the inductor pulsed-power supply with higher energy. [ABSTRACT FROM PUBLISHER]

A novel circuit with the better performance for the inductive pulsed power supplies in the electromagnetic launch system is proposed in this paper, namely, the meat grinder with capacitive pulse forming unit (CPFU). Its working process is qualitatively analyzed stage by stage. Its practical feasibility is verified through a 7.5-kJ experiment. From the perspectives of circuit structure and working principle, this circuit can be regarded as the combination of a meat grinder and a CPFU. Compared with its preceding circuits, this circuit possesses following advantages: 1) the self-recovery of the capacitor precharged voltage can easily be achieved, which is conducive to continuous operations of the whole circuit and 2) the waveforms of the inductor currents contain no capacitive components, which can promote the energy storage density of the inductors. [ABSTRACT FROM PUBLISHER]

The opening switch is one of the critical technologies in the development of inductive pulsed-power supply. The power requirement is very high when the opening switch is desired to commutate a large current. This paper presents a zero-current opening circuit for inductive pulsed-power supply based on a high-temperature superconducting pulsed-power transformer. First, there are two types of current flowing through the opening switch, one comes from the secondary side of the pulse transformer, and the other one comes from superconducting energy storage inductance. The orientation of the two current is opposite. Then, when the current flowing through the opening switch closes to zero, the switch is opened and this restrains the over-voltage pulse of the opening switch. The simulation results indicate that this zero-current opening circuit is feasible and has potential applications for high-energy systems in the future electromagnetic launcher. [ABSTRACT FROM PUBLISHER]

This paper describes a compact high storage density inductive–capacitive storage module. The module is based on high-power opening switches using inverse current commutation with semiconductor devices commutation principle and a high storage density Brooks inductor. These opening switches, being able to switch-OFF pulse currents up to 14.5 kA by the counter-current subcircuit, make use of the general property of a standard high-power thyristors impedance transition from closing state to blocking state. The experimental results show that with the primary capacitor and counter-current commutation subcircuit charged voltage 3 and 2.5 kV, respectively, the charged current of the Brooks-type inductor is about 14.5 kA, with a charged time of about 4.5 ms. The output peak current of the inductive storage module is about 21 kA. The total stored energy is about 54.9 kJ while the energy density of the inductor is approximately 6.69 MJ/ \textm^3 , which is not including the primary storage and commutation unit. [ABSTRACT FROM PUBLISHER]