Search

In this paper, a 25-kW bipolar pulsed-power supply for strategic mineral exploration has been described. A 500-V, 12.5-A unit module consisting of a highly efficient LCC resonant converter and a full-bridge-based bipolar pulse-switching unit is designed. The LCC resonant converter has a trapezoidal-shaped resonant current for reduced conduction loss. For achieving high power density, the leakage inductance of the transformer is used as resonant inductance without an external inductor. Moreover, the designed gate drive circuit based on the repetitive short pulse is proposed to operate the frequency range from dc to 8 kHz and reduce the size of the gate transformer. Four modules are connected in series and parallel in order to operate the power supply in either loop mode or grounded dipole mode. Depending on the load condition, the pulse power source capable of delivering the required high voltage and low current (2 kV, 12.5 A) or low voltage and high current (500 V, 50 A) is operated either in grounded dipole mode or loop mode, respectively. In order to satisfy the output voltage balancing of the four modules, the third wire is wound to compensate for the transformer of the LCC resonant converter. Finally, the design of the bipolar pulsed-power supply has been verified based on the experimental results of the field test. [ABSTRACT FROM AUTHOR]

This paper proposes a flyback-circuit-based design of a trigger circuit for a high-power gas switch. By incorporating a flyback circuit in a high-power gas switch, it is possible to generate a high step-up ratio and high-voltage pulse by using a transformer. Furthermore, simple trigger circuit having the minimum possible number of components (transformer and switch) can be realized. When an inductor is used as an energy storage element, energy is stored as a current source, and thus, the element can operate reliably when low impedance exists between the trigger node of the switch after triggering. According to the fundamental operating principle of a flyback circuit, the proposed trigger circuit is designed considering the maximum trigger voltage and energy required for a high-power gas switch. To verify the proposed design procedure and feasibility of the trigger circuit, a compact trigger circuit (7.5 kV, 1.3 mJ/pulse) is simulated using the PSpice program and implemented. Based on this compact circuit, a trigger circuit (20 kV, 100 mJ/pulse) for a triggered vacuum switch (TVS) is developed, and the tests with an actual TVS (3.3 kJ) are carried out. [ABSTRACT FROM AUTHOR]

In this paper, the detailed design of an ion pump power supply is presented. The ion pump power supply was designed based on an LCC resonant topology with high switching frequency to take advantage of a smaller transformer for isolation. Because the proposed ion pump power supply has a 7-kV, 50-mA specification, high-voltage insulation is required. In order to secure insulation reliability, the power supply was designed with eight separate transformers that share primary turns. The spacing between the primary turns and secondary turns allows for increases in the leakage inductance and parasitic capacitance of the transformer. A compact design can be achieved using the parasitic component generated by the proposed design as the resonant parameters of the LCC resonant converter. In addition, based on a trapezoidal approximation of the LCC resonant converter, the resonant parameters are designed to have trapezoidal shapes of the resonant current in order to reduce conduction loss. Finally, the results of the experiment indicate that the developed ion pump power supply can be used effectively in high-voltage and low-current applications. [ABSTRACT FROM AUTHOR]

This paper presents the design and experimental results of the 36-kW pulsed-power supply for the xenon flash lamp. The continuous conduction mode series-parallel resonant converter is modified. This means that not only the few hundred kilohertz of high switching frequency is introduced to replace the resonant inductor with the leakage inductor of transformer but also the high output current is accomplished by using three-phase delta-connected transformers. In addition, the snubber capacitor of the inverter switches and the power factor correction module is both omitted in the compact structure. Although these main components have changed, the efficiency and power factor of the rated dummy load reach 96% and 0.96%, respectively. Within 36-kW average power, the proposed pulsed-power supply can generate as versatile combination of output pulse. For example, it can generate 20-ms pulse with 1-Hz repetition rate or generate 1-ms pulse with 20-Hz repetition rate. The used insulated gate bipolar transistor is protected from the turn-OFF peak voltage by the snubber circuit, and the effect of the snubber circuit is shown at the actual load condition. [ABSTRACT FROM PUBLISHER]