Search

Weather-related or other types of faults can negatively impact the continuity of the electricity delivery to the consumers and, thus, lead to poorer reliability scores. 90% of customer outage-minutes are due to events which affect local distribution systems. The radial configuration is simple and has a low cost design; however, when a fault occurs it often causes power outages beyond the location of the fault itself. Therefore, it is beneficial for utilities to automatically isolate the fault and, thus, restore power to as many consumers as possible. The benefits of fault isolation and service restoration include, but are not limited to: enhanced reliability and resiliency, reduced loss of revenue to the utility, and enhanced comfort and satisfaction for the utility’s consumers. This paper provides an algorithm to quickly isolate a fault and automatically restore power to as many nodes of the distribution system as possible by opening and closing switches already placed within the system. The expert model and centralized algorithm that are proposed in this paper guarantee an optimal solution and a short run-time regardless of the size of the distribution system. A mathematical proof of the optimal nature of the solution is provided. In addition, the model is validated in practice, solving two different-sized systems. [ABSTRACT FROM AUTHOR]

This paper proposes an accurate impedance model for line commutated converter (LCC) in the stationary frame. The commutation overlap process caused by the transformer leakage inductance complicates the modeling for LCC. Traditional impedance models are derived in positive sequence and negative sequence frame based on the simplified commutation overlap process, which degrades the modeling accuracy and limits the description of frequency coupling. This paper systematically analyzes the effects of the commutation overlap process on the impedance model, and the impedance model with the accurate commutation overlap process is established in the dq-frame. For clearly revealing the frequency coupling phenomenon of the LCC, the complex space vector is employed to extend the impedance model in the dq-frame to the complex αβ-frame. A closed-loop model on PSCAD/EMTDC is used to verify the proposed impedance model in the time-domain and the frequency-domain. The consistency between the simulation results and theoretical analysis effectively verifies the accuracy of the proposed model. [ABSTRACT FROM AUTHOR]

This paper presents the possibilities of reducing emergency situations and reducing the time of failure in the power grid. The paper contains a detailed description of the method (algorithm) of operation in emergency situations on the example of a Gas-Insulated Switchgear (GIS) located in one of the system-forming (node) stations in the power grid. The level of detail contained in this paper, which has not been previously encountered in previous publications, favors an in-depth understanding of the possible solutions that result from these emergencies. The above method (algorithm) of activities has been developed based on three levels of research: simulation, theoretical and practical. This means that the simulation analysis that was performed based on theoretical information was experimentally tested as part of an emergency situation in one of the system-forming (nodal) stations in the power system. In order to achieve the result described in this article, one of the most promising types of devices used in power systems was selected - the GIS. This has been confirmed by numerous analyzes of the effectiveness of these devices included in this article. The paper contains a detailed description of the individual steps in the field of corrective actions and aimed at minimizing downtime. In addition, this article provides guidance to monitor possible emergencies that are designed to increase the reliability of the power grid. [ABSTRACT FROM AUTHOR]

The degradation of the electrical contact in a gas insulated switchgear (GIS) is closely related to overheating at the contact. However, the disconnector contact is one of the hot contacts in GIS. Therefore, in this paper, the finite element method was used to solve the three-dimensional multiphysics coupling temperature rise field and flow field in the Single Phase in One Tank (SPIOT) type GIS disconnector under different operating conditions. From the perspective of temperature rise field and flow field, this paper analyzed the temperature rise characteristics under different working conditions and explored the feasibility of the direct application of air, CO2 and C4F7N/CO2 mixed gas to an electrical device. The disconnector temperature rise experiment platform was then built to verify the simulation. The results showed that the temperature rise field and the flow field distribution were similar in four gas environments. SF6 gas had the smallest temperature rise, followed by C4F7N/CO2 mixed gas, and the temperature rise of CO2 and air was relatively large. Therefore, from the perspective of the temperature rise field and flow field, it was feasible to directly apply C4F7N/CO2 mixed gas to an electrical device in order to meet insulation requirements. [ABSTRACT FROM AUTHOR]

In the conventional sliding mode control, the four-leg distribution static compensator (DSTATCOM) currents are controlled based on a current error in each phase. However, the four currents in a four-wire system can not be independently controlled variables and hence one of the four controllers is redundant in conventional schemes. Further, the current dynamics of a DSTATCOM converter are coupled through converter pole voltages in the natural reference frame. This leads to cross-coupling in the sliding variable equations with respect to four manipulated input variables. Considering the above points, in this paper, the current due to Thevenin’s equivalent load neutral-point voltage is considered as a fourth independent controlled variable and the corresponding system dynamic equations are presented. To get a decoupled feature, a new sliding surface function is structured. The performance of a DSTATCOM with the proposed control scheme under various operating conditions is validated through a detailed simulation study and experimental results, obtained from a laboratory prototype of four-leg DSTATCOM. [ABSTRACT FROM AUTHOR]

This paper presents frequency domain (FD) Norton-type equivalents of single- and three-phase photovoltaic (PV) generators, aimed at transient calculations. The proposed equivalents can be interfaced with a general frequency-dependent network and/or nonlinear loads and include voltage/current sources representing initial conditions aimed at partitioned-time transient simulation. The transient solution is performed via the numerical Laplace transform (NLT) in a sequential scheme by using time sub-windows with corresponding initial conditions and using reduced number of samples. The proposed approach overcomes the issue of computationally heavy simulations as in classical implementations of NLT. Two case studies involving PV generator and nonlinear load are presented to illustrate the performance of the proposed FD PV models. [ABSTRACT FROM AUTHOR]

To calibrate non-contact sensors with fast response and high scale factor, it is critical to develop step pulse generators capable of generating standard high voltage step pulses and accurately measuring the generated waveform. In this paper, two types of step pulse generators are designed with output voltages of 2 kV and 100 kV. The 2 kV step pulse generator can generate a step pulse with a rise time of ∼300 ps and an adjustable pulse width. A step pulse with a rise time less than 5 ns and a pulse width over 1 μs can be generated with the 100 kV step pulse generator. The uncertainty of 2 kV step pulse generator is then analyzed by simulations and experiments. Finally, a performance comparison with step pulse generators in previous studies is carried out. Bandwidth, linearity and repeatability of the sensors can be verified with the designed two step pulse generators. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

Most microgrid protection schemes found in published literature suffer from a lack of generality in that they work well for the assumed topology, including type and placement of sources. Other generic protection schemes tend to be too complicated, too expensive, or both. To overcome these drawbacks, a topology-agnostic, scalable, and cost-aware protection based on fundamental principles that work in the presence of high penetration of inverter-based resources (IBRs) is developed and tested in this paper. The protection system also implements stable automatic reconfiguration of the healthy sections of the system after clearance of fault, thus increasing resilience by self-healing. To achieve this ambitious goal, stable inverter models are developed that operate in unbalanced networks in grid-connected and islanded modes, even with 100% IBRs, share power without conflicting controls, and can ride through faults while limiting fault currents. The scheme is tested for primary and backup protection and reconfiguration on the IEEE 123-node feeder in grid-connected and islanded modes with 15 IBRs connected to the system. [ABSTRACT FROM AUTHOR]

Voltage source converters (VSCs) have been extensively used in power systems for interfacing renewable energies and other modern loads. Because of their nonlinear nature, a proper harmonic model of VSC devices must be established when conducting harmonic analyses in power systems. This is especially true for low-order harmonics, which are routinely encountered in present power systems. To this end, an analytical harmonic model that represents the low-order harmonic characteristics of VSCs is developed in this paper. The new model takes both the control loop and power loop (i.e., DC-link capacitor) of the VSC into account through rigorous mathematical derivations. The final result has shown that the VSC can be represented by a harmonically coupled impedance matrix at harmonic frequencies, which can be easily used for harmonic analyses of large-scale power systems. It also shows that the DC-link capacitor has a more noticeable impact on the harmonic impedance of VSCs with a smaller DC-link capacitance and low-order harmonics. The appropriateness of the new model was verified using EMT simulations and lab experiments. A complete procedure to construct the proposed VSC model is also established based on the research findings. [ABSTRACT FROM AUTHOR]

This paper proposes a sound separation methodology based on deep learning neural network (DLNN) to extract useful diagnostic material in non-invasive audio-based On-Load Tap Changer (OLTC) diagnostics. The proposed methodology has been experimentally verified on both artificial mixtures (created by reproducing the targeted data by the speakers placed next to the active transformers) and actual mixtures (recorded by the microphone during OLTC live operation in the field). The results show that the method produces high-quality estimates (correlation to referent fingerprints $\rho > 0.9$) compared to other sound separation methods, e.g. Independent Component Analysis (ICA). The proposed framework can also perform source separation from a monaural mixture (mixture recorded with a single microphone only), which is impossible for ICA methods. Moreover, the results show that DLNN trained with healthy OLTC data produces diagnostically valuable estimates even when fed with a faulty OLTC audio mixture. For that reason, once trained, the DLNN can produce the diagnostic signal estimates from monaural mixtures that can be used with existing vibration-based diagnostic methods. [ABSTRACT FROM AUTHOR]

Line-commutated converters are extensively used as the interface between ac grids and classic HVDC systems. At the inverter side, commutation failure of switches is one of the most common faults that can pose threats to the system operation. Practical and reliable study of such phenomena relies on accurate and efficient converter models for simulations. Recently, a parametric average-value model (PAVM) has been presented for ac–dc rectifiers, which considers the internal faults of the converter. In this paper, the PAVM methodology is extended to the dc–ac inverter systems, including the commutation failure of switches. The proposed PAVM also augments an automatic fault detection technique to determine the faulty switches. Using comprehensive simulation studies, the developed model is verified to accurately predict the commutation failure of switches and reconstruct the waveforms consistent with the detailed switching models of inverters while being computationally more efficient. The proposed PAVM is envisioned to be an efficient and accurate asset for simulation of HVDC systems and inevitable when faults of switches need to be considered. [ABSTRACT FROM AUTHOR]

The effect of reduction in the terminal voltage of a grid-tied inverter together with minimization in total harmonic distortion (THD) of terminal voltage and current, in the presence of dead-band in the switching remains always challenging for the researchers. With high switching frequency, this issue increases by many folds. The grid-tied inverter used for harmonic compensation acts as a shunt active power filter (SAPF). The implementation of the dead-band elimination technique is based on output current polarity detection, suffers from multiple zero-crossing due to the generation of high frequency switching harmonics during SAPF operation. This paper deals with a dead band elimination methodology together with harmonic compensation using SAPF under non-linear and unbalanced loading conditions. Here, SAPF uses a dual fundamental component extraction (DFCE) scheme with modified complex coefficient filter (MCCF) to extract fundamental components for reference current generation to implement an indirect current control PWM scheme. MCCF extracts fundamental components even in the presence of dc offset and unbalancing at the input. For incorporating dead-band elimination in control, exact polarity detection is done separately through SAPF output current estimation using sensed load current, and modified CCF computed reference source current. Since the estimated SAPF output current contains no high-frequency switching harmonics, the dead-band elimination technique can be correctly implemented. To synchronize the zero-crossing of the estimated and actual SAPF current, an adaptive delay control is used. The proposed MCCF based control logic’s performance together with the dead-band elimination technique is validated for SAPF operating under non-linear, unbalance, and dynamic load conditions. The proposed dead-band elimination scheme based SAPF model is developed and simulated using MATLAB/ SIMULINK. The simulation results show a significant reduction in source current harmonics due to the elimination of odd harmonic injection into the system by incorporating dead-band elimination in SAPF operation. The real-time simulation of the proposed method is also validated using OPAL-RT OP4510 real-time platform. [ABSTRACT FROM AUTHOR]

The missing capability of DC fault current limitation is an inherent disadvantage in the typical half-bridge modular multilevel converter (MMC), which restricts its application in long-distance high voltage direct current (HVDC) systems. The full-bridge submodule (FBSM) and clamped double submodule (CDSM) topologies allow for fault current self-clearing, but also suffer from additional hardware cost and power losses. In this paper, an improved submodule topology utilizing the new reverse-blocking insulated gate bipolar transistor (RB-IGBT) is proposed to improve system economy without compromising its performance. The operating principles and DC fault characteristics of the proposed topology are analyzed in details, including comparison with various topologies in terms of cost, losses, fault current clearing speed and thermal. Compared with the traditional CDSM topology, the proposed RBSM can clear DC faults faster with reduced cost of switching devices. A DC fault protection strategy for MMC-HVDC system is also presented. Simulation results under normal operating, permanent and transient fault conditions are carried out to verify the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

In a previous paper (Part 1) the authors have performed the simulative evaluation of the life lost by HVDC extruded cables subjected to long TOVs occurring in VSC HVDC cable systems. The conclusions were that it cannot be completely ruled out that the field levels and the duration of such TOVs are a potential threat to certain cable designs, and tests other than Load Cycling Type Tests after CIGRÉ Technical Brochure 496 could assess quantitatively the potential threat associated with long TOVs. For these reasons, in this Part 2 superimposed switching impulses applied during Type Tests after TB 496 are analyzed in order to check if such impulses might be equivalent to long TOVs as for their electro-thermal stress effects on extruded insulation. The analysis is similar to that carried out for long TOVs in Part 1, i.e., it consists of: calculating the electric field during superimposed switching impulses; comparing it with the field during long TOVs; calculating with Miner's law of cumulated damage the life lost during superimposed switching impulses and comparing it with the loss of life during TOVs. A brief literature survey of potential high field effects during long TOVs is also reported. [ABSTRACT FROM AUTHOR]

Identifying the location of partial discharges (PDs) and providing clear information on insulation vulnerabilities in power systems can help utility companies to improve their maintenance efficiency. This paper presents a PD monitoring and locating system for medium-voltage switchgears using a set of transient earth voltage (TEV) detectors. A time-of-flight methodology was used to identify the switchgear affected by PD among a row of switchgears. A time sharing access mechanism, which was implemented by multiple high-frequency surface mounting relays integrated into each TEV detector, was applied to automatically identify the site of PD and minimize the number of expensive high-speed acquisition cards. The operation principle and implementation of the modular system were formulated, and the efficiency of the proposed system in identifying the switchgear with PD among three 10 kV metal-clad switchgears was confirmed experimentally. [ABSTRACT FROM AUTHOR]

Operational performance in the low-voltage distribution network (LVDN) can be undermined by its inherent unbalances, which may become worse as the penetration of rooftop solar continuously increases. To address this issue, load balancing via phase-reconfiguration devices (PRDs), which can change phase positions of residential customers as required, provides a cost-efficient option. However, most reported approaches to control PRDs require that demands of all residential customers are available, which are not viable for many LVDNs without smart meters or advanced metering infrastructure (AMI) installed. To bridging the gap in this field, this paper proposes a novel method to control PRDs purely based on measurable data from PRDs, and its controller. Based on limited information, sensitivity analysis in the network with PRDs is studied, followed by the optimization model that comprehensively considers operational requirements in the network. Moreover, slack variables are introduced to the model, and penalized in the objective function to assure either a strategy that is secure or with minimized violations can always be provided. The model is a challenging mixed-integer non-convex programming (MINCP) problem, which is reformulated as an efficient solvable mixed-integer second-order cone programming (MISOCP) based on exact reformulations or accurate linear approximations. Simulations based on two modified IEEE systems, and a real system in Australia demonstrate that an efficient strategy can be provided to mitigate unbalances in the network. [ABSTRACT FROM AUTHOR]

For Electro-Magnetic-Transient (EMT) simulations of power networks with switches, techniques such as linear interpolation and Critical Damping Adjustment (CDA) are widely used for improving numerical robustness. This paper analyzes the numerical stability of simulations with these techniques. Firstly, it is mathematically shown that the interpolation or CDA step is equivalent to the introduction of additional switching states. Subsequently, Common Quadratic Lyapunov Function (CQLF) theory is used to investigate the numerical stability of the whole simulation considering these new switching states. It is proved that the widely used strategies like linear interpolation and CDA always result a stable simulation if the original switched system is strictly passive in all switching states. Finally, it is shown that the developed approach can be used to determine the stability of other practical interpolation methods. Examples are provided to verify the proposed technique. [ABSTRACT FROM AUTHOR]

Natural calamities always have been a serious threat to energy systems. In this regard, this paper constitutes a stochastic mixed integer linear programming (SMILP) model to enhance the resilience of power distribution systems to deal with disastrous events. In particular, the proposed model is developed to enhance both survivability and restoration capability of distribution systems. In this regard, to increase the preparedness of the power distribution system, the system operator reconfigures the network by utilizing remote-control switches (RCSs), manual switches (MSs), and distributed generations (DGs) before the natural calamity hits. The proposed model contemplates the traveling time of crew teams to the MS sites in the transportation system in order to achieve the best switching sequence. In addition, it pre-positions the crews and mobile emergency generators (MEGs) in staging locations to hasten the likely post-disturbance operations. To do so, likely post-event operations are included in the model using the scenario generation technique. To validate the performance of the developed model a distribution system is employed. The results of simulations confirm the effectiveness of the proposed approach in declining the interruption of electric energy for customers. [ABSTRACT FROM AUTHOR]

The capacitor condition monitoring is an important issue for the reliable operation of modular multilevel converters (MMCs) in high-voltage applications. The numerous capacitors make the monitoring for the capacitor condition complex and computation-consuming. This paper proposes a hierarchic capacitor condition monitoring strategy to assure the reliability of high-voltage MMCs. In the strategy, the switching times of the switching signals are counted to detect the condition of the capacitor in each submodule (SM). Then, the subsequent capacitance calculation method is only conducted to the abnormal capacitors indicated by the above condition detection algorithm. Meanwhile, the variations of the measured and reference capacitor voltages are employed to calculate the capacitance in the proposed method. The condition detection algorithm shrinks the scope where the abnormal capacitors locate, which avoids calculating the total capacitances in MMCs. In the proposed capacitance calculation method, the complex operations are further saved. Both the two measures reduce the computation burden effectively. The implementation of the whole monitoring strategy is simple and fit for high-voltage MMCs. Moreover, the strategy has no adverse influence on the normal operation of MMCs. The effectiveness of the proposed strategy is verified by the simulation studies with the professional tool Matlab/Simulink. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) in high- voltage applications contain large numbers of power switches, which increases the fault probability inside MMCs. This paper proposes a detection method for the faulty arm containing switch open-circuit failures in high-voltage MMCs to improve the reliable operations of MMCs. The proposed method uses the periodicity of the deviation between the maximum and minimum capacitor voltages to provide the detection reference. To yield a reliable reference, the repetitive signal generator is employed. Then, the fault is identified by the difference between the referenced and measured capacitor voltage deviations. An auxiliary criterion is also designated to avoid the false detection caused by the mutations in MMCs. The proposed method can reduce the difficulty in the selection of thresholds. Moreover, the proposed method is robust in high-voltage MMCs with inferior capacitor voltage balancing performance, which ensures detection rapidity and accuracy. Finally, the feasibility of the method is verified by simulation results in Matlab/Simulink. [ABSTRACT FROM AUTHOR]

Piezoelectrically actuated fast mechanical switches provide a low-loss conduction path in hybrid circuit breakers for protecting medium-voltage direct-current systems. As the desired actuation speed approaches the driving limit of a piezoelectric actuator, excessive vibration starts to dominate its underdamped travel curves, resulting in insulation failures and delayed switching in the fast mechanical switch. To improve the underdamped travel curves into critically damped travel curves, several switching motion control schemes with active damping filters are proposed in this paper. The switching motion controllers are based on an electromechanical model of a fast mechanical switch with experimentally identified parameters. According to hardware implementation tests, the proposed closed-loop control schemes optimized the switch travel curves with a 56% reduction in the undershoot and a 75% reduction in the settling time. Equipped with the critically damped travel curves, the piezoelectrically actuated fast mechanical switch is better suited for sequential submodule operations to reduce the interruption time, the peak current and the fault energy to be absorbed in hybrid circuit breakers. [ABSTRACT FROM AUTHOR]

Uncertainties in power system studies are typically managed by Monte Carlo methods or by applying some worst case assumptions. As the number ofuncertainties increases, there is a need for methods that can estimate statistical parameters from a limited number of calculations. This paper utilizes a method called the Unscented Transform together with Cornish-Fisher expansion to estimate the 2%-value of switching overvoltages using only about one tenth the number of calculations as a Monte Carlo method, with similar accuracy. The uncertainties considered are the energizing instants of the three phases. The method is illustrated through EMT simulations in PSCAD and it is shown to provide a good approximation of the 2%-value in most of the studied cases. [ABSTRACT FROM AUTHOR]

Different from typical circuit breakers, breakers used to switch AC filters in convertor stations have to operate frequently according to the real-time operation mode and daily load changes. Therefore, the performance of filter breakers decreases very quickly, which leads to frequent accidents. Both preinsertion resistors and controlled switching devices can suppress switching transients. In this paper, a comparative analysis of whether a controlled switching device and preinsertion resistor should be adopted is carried out using PSCAD. The transient is calculated as the combined result of the switching angle and preinsertion resistor value, and the optimal configurations are proposed. After determining the resistor value and whether a controlled switching device should be included, the reference voltage of the arrester should be reevaluated. [ABSTRACT FROM AUTHOR]

This paper proposes a new passive Islanding detection approach for the Inverter Interfaced Distributed Generators (IIDGs) operating under different control modes. First, a novel index is formulated using Root Mean Square (RMS) value of the voltage and the frequency information, acquired at the Point of Common Coupling (PCC) of the target DG. The index is then post-processed by estimating the number of peaks and valleys $(N_{p_{k}-v})$ in a cycle using the sliding window concept, which indicates the occurrence of an event. Finally, the nature of the event, i.e., Islanding or non-Islanding, is decided by exploiting the two statistical features viz., Square of RMS $(S_{RMS})$ of $N_{p_{k}-v}$ and Average Crest Factor $(ACF^{m})$ of the proposed index. The performance of the proposed method (P-IDM) is demonstrated through comprehensive studies in PSCAD/EMTDC for the single-bus and IEEE 34-bus Active Distribution System (ADS). Also, the real-time validation is performed for the IEEE 34-bus using Controller Hardware-in-the-Loop (CHIL) setup comprising of Real-Time Digital Simulator (RTDS) and dSPACE1104. The simulation and hardware results for different test systems indicate that the proposed scheme, being generic in nature, sustains its efficacy under various interface controls of IIDGs. Finally, a comparative assessment with the other existing Signal Processing (SP) based passive methodologies shows the supremacy of the proposed method in terms of accuracy and faster detection. [ABSTRACT FROM AUTHOR]

This paper presents a combined control scheme that consists of two complementary control strategies, namely hierarchical control and autonomous control to handle contingencies in a multi-terminal high voltage direct current (MTDC) system. The proposed hierarchical control considers three optimal targets, i.e., equal or proportional power sharing, minimizations of transmission loss and total DC voltage variation. The primary control layer implements the droop control for voltage source converters (VSCs). While in the secondary control layer, voltage reference setpoints of the VSCs in droop control scheme are calculated by the proposed optimal power flow method with the equal or proportional power sharing as equality constraints. As the hierarchical control relies on communication system, the autonomous control for power sharing can be activated during communication system malfunctioning or rapid power variation caused by renewable energy sources. The combined control strategy can greatly increase the reliability of the MTDC system. The simulation results of a five-terminal MTDC network conducted in the MATLAB/Simulink software verify the performance of the proposed combined control strategy. [ABSTRACT FROM AUTHOR]

High penetration level of single-phase solar PVs in low voltage distribution systems has raised concern about the Voltage Unbalance (VU) level. Real-time phase reconfiguration using Dynamic Switching Devices (DSD) has been proposed as a cost-effective solution to mitigate the excessive level of Voltage Unbalance. DSDs are fast power electronics devices that could change the phase connection of a solar PV with minimum disturbances. Most of the proposed methodologies for controlling DSDs are based on a central controller and the assumption of availability of Advanced Metering Infrastructure (AMI) and a communication system. In this paper, we propose a distributed control methodology to control DSDs based on the measurement from the local node only and using the sensitivity of nodal voltage to power injection. Each DSD decides on phase swapping if it rectifies the unbalance index of the local node. We show that decreasing the Voltage Unbalance Factor (VUF) of individual nodes will improve the unbalance situation of the whole feeder. The proposed scheme does not require a communication system nor a central controller. The result of simulations confirms the efficacy of the proposed methodology. [ABSTRACT FROM AUTHOR]

VSC-HVDC systems are being increasingly employed in the power systems. The recently installed HVDC systems have a power capacity similar to traditional power plants. Hence, they are expected to have a similar behaviour as traditional synchronous generators during faults in AC grid, within their limits of course. Recent grid codes require HVDC converter stations to incorporate fault ride-through (FRT) capabilities in order to avoid HVDC converter station disconnection from AC grid for certain fault characteristics. In this paper, two FRT mechanisms are suggested for the two converter stations of an HVDC system. One FRT mechanism is added to the DC voltage control loop of the master converter station, while the other FRT mechanism is added to the active power control loop of the slave converter station. The objective is to ensure the stable operation of the HVDC system during faults that may occur in AC grids located on both sides of the HVDC system. The performance and stability of the suggested FRT mechanisms are tested considering the pre-fault power flow direction and all possible types of balanced and unbalanced faults. Simulation results confirm the effectiveness of the FRT mechanisms and revealed the critical modes during FRT operation. [ABSTRACT FROM AUTHOR]

On March 31, 2019, a 500 kV air-core, shunt reactor at a large generating station in BC Hydro was damaged shortly after four unit transformers were simultaneously energized from a 500 kV series and shunt compensated line source. Forensic investigations revealed that the controlled switching system, controlling the instant at which each breaker phase closes during energization to minimize inrush current, had failed. Uncontrolled closing led to under-damped, high-magnitude and sub-synchronous currents. Protection tripped and isolated the four transformers, followed shortly by shunt reactor protection tripping. Before the reactor could be isolated by circuit breakers, a damaging internal fault developed. This paper presents forensic investigation describing sequence of events leading up to reactor damage and shares the lessons learned with the peer utilities having similar installations.    [ABSTRACT FROM AUTHOR]

The integration of overhead lines in future MTDC grids leads to a higher fault rate compared to cables. Most of the faults are considered to be non-permanent, so that the line can be reconnected after dielectric recovery. The auto-reclosing procedure in HVDC systems reveals new challenges since multiple restrikes are possible within a short period of time. This paper proposes an auxiliary circuit for DC Circuit Breakers (DCCB) which enables to use the DCCB internal capacitor for the line pre-energization. A comprehensive description of the switchgear operations during the pre-energization sequence is provided and the fault property identification method is defined. The method is validated by simulations in a MTDC grid and a sensitivity analysis is carried out using EMTP-RV. [ABSTRACT FROM AUTHOR]

Condition assessment of Medium Voltage switchgears requires effective, but inexpensive solutions to become a common practice. On the other hand, failure of a switchgear component can cause cascade effects and outage of other apparatus, in addition to significant economic losses due, e.g., to lack of energy availability. A major diagnostic property to evaluate switchgear health and reliability is partial discharges, being a direct cause of failure of organic insulation systems. A new approach to automatic, self-assessment of switchgear reliability based on partial discharge, PD, acquisition and processing, as well as a new type of PD sensor solution are presented in this paper. The sensor is based on the capacitive divider existing in most bushings to indicate the presence or absence of voltage. The innovative automatic software is able to provide automatic noise and PD separation, noise rejection and type of PD-source identification. The embedded bushing sensor has been tested on switchgears in the presence of defective components as cable terminations and bushings. Results show that the sensor, coupled with the automatic software, is able to provide good sensitivity compared to other sensors, and good capability to locate the cabinet and identify the type of source generating partial discharges. [ABSTRACT FROM AUTHOR]

Medium voltage direct current (MVDC) power systems are in their early phase of development, but the lack of efficient and reliable DC circuit breakers is currently one of the most significant bottlenecks for widespread adoption of MVDC applications. Compared to protection devices in high voltage direct current (HVDC) systems, MVDC circuit breakers are expected to interrupt fault currents with higher rates of rise in more power-dense and more controllable structures. A hybrid approach with a piezoelectrically actuated fast mechanical switch in parallel to a solid-state circuit breaker is expected to meet the above requirements. A prototype of a 15 kV-class piezoelectrically actuated fast mechanical switch is presented in this paper. The prototype demonstrates an actuator opening time of 1 ms, a breakdown voltage of over 20 kV, and a continuous current rating of 500 A. After integrating the fast mechanical switch into a hybrid circuit breaker testbed, the fast mechanical switch was able to open within 1.5 ms and the fault was cleared within 5 ms. Therefore, piezoelectrically actuated fast mechanical switches can enable fast, reliable and controllable protection for various MVDC systems like electric ships, electric aircraft and microgrids that integrate distributed energy resources. [ABSTRACT FROM AUTHOR]

Network topology identification (TI) is an essential function for distributed energy resources management systems (DERMS) to organize and operate widespread distributed energy resources (DERs). In this paper, discriminant analysis (DA) is deployed to develop a network TI function that relies only on the measurements available to DERMS. The propounded method is able to identify the network switching configuration, as well as the status of protective devices. Following, to improve the TI resiliency against the interruption of communication channels, a quadratic programming optimization approach is proposed to recover the missing signals. By deploying the propounded data recovery approach and Bayes’ theorem together, a benchmark is developed afterward to identify anomalous measurements. This benchmark can make the TI function resilient against cyber-attacks. Having a low computational burden, this approach is fast-track and can be applied in real-time applications. Sensitivity analysis is performed to assess the contribution of different measurements and the impact of the system load type and loading level on the performance of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper presents and evaluates a discrete-event control-based Supervisory Controller (SC) for a grid-connected, battery-enabled, DC Fast-Charging (DCFC) station for Electric Vehicles’ (EVs). The SC enhances operational resiliency of the DCFC station and its host grid by decoupling the dynamics and limiting the steady-state power between the station and its host grid. The charging station includes multiple DCFC units, a Battery Energy Storage System (BESS), a solar-PV unit, and a grid-interface Voltage-Sourced Converter (VSC). The SC (i) limits the station-imported power from the grid based on the grid-imposed requirements, (ii) dynamically dispatches power flow among the grid, PV unit, DCFC units, and BESS to meet charging needs of EVs and when applicable charges BESS or exports power to the grid, (iii) protects the BESS by enforcing its state of charge upper and lower limits and the maximum charge/discharge rates, and (iv) enables the VSC to provide grid ancillary services, if required. Simulation results in PLECS software platform are given to assess the dynamic performance of the proposed SC in response to various discrete events/transitions. The SC algorithm is implemented on a Programmable Logic Controller (PLC) and verified based on real-time Hardware-In-the-Loop approach using an OPAL-RT platform. [ABSTRACT FROM AUTHOR]

In a line-commutated converter based high-voltage direct-current (LCC-HVDC) system, the inverter control system usually includes constant extinction angle (CEA) controller, constant current (CC) controller, current error controller (CEC), and voltage-dependent current order limiter (VDCOL). However, the interaction influence of multiple controllers may cause repetitive commutation failure (CF). For this purpose, this paper deeply investigates the mechanism and the influencing factors of repetitive CF caused by controller interaction. It is found that the lower limit value of CEA controller can affect the control switching process and thus the probability of repetitive CF. Besides, the minimum gamma measurement (MGM) unit prevents the system from acquiring the real extinction angle in time, which results in the DC current fluctuation during the recovery process. Moreover, the probability of control-induced repetitive CF is much higher when the HVDC inverter is connected to a weak AC system or the AC fault is not serious but not cleared in time. Based on the above analyses, an improved control method is proposed for recovery performance improvement, which is mainly realized by modifying the lower and upper limits of the CEA controller during recovery. Finally, the simulation and experimental results verify the theoretical analyses and the proposed control method. [ABSTRACT FROM AUTHOR]

A mechanical switch can be used instead of a power electronic load commutation switch in orderto reduce the losses during normal power flow in standard hybrid DC circuit breakers. The success of current commutation in such hybrid breakers depends on the arc voltage formed across the contacts in the mechanical switch. The behaviour of rapidly elongated, wall constricted arcsgenerated during the opening of an ultra-fast mechanical switch in the air is studied here. The voltage-current characteristics of the generated arcs are obtained for steady state contact opening velocities of 6, 11 and 21 m/s. It is found that the arc voltage at a given current and contact separation increases with the contact opening velocity. It is shown that stationary,zero-contact-velocity characteristics can not be used to accurately quantify the voltage build-up in fast elongating arcs in hybrid breakers. A best-fitting black-box equation for the dynamic arc characteristics is presented for the tested velocities. The obtained voltage-current characteristics are used as input to simulate the current commutation process in a 12 kV hybridDC circuit breaker case-study. Different scenarios of current commutation failure related to the arc voltage build up are identified. It is shown that these failures scenarios can be avoided by increasing the contact opening velocity. [ABSTRACT FROM AUTHOR]

The article analyses design options for a practical 2-10 kV, 1-2 kA LC DC Circuit Breaker module. The impact of multiple series break points with the ultra-fast disconnector is explored in depth using analytical model and 5 kV, 4-break hardware prototype. The experimental testing demonstrates that the arc voltage increases proportionally with each breaking point, and this increases current that can be internally commutated. Further analysis of the impact of delays between break points is presented. Modeling and testing with 4 different capacitors of 1-10 kV concludes that larger capacitances increase commutating current, but relationship is complex and non-linear. Parallel connection of breaking points is also analysed. Successful breaking of DC fault current is demonstrated on hardware for multiple cases including 930 A with 800 $\mu$ F, 6.5 kV, capacitor using a 4-break disconnector. The tested DC CB is of mechanical type, which inserts a capacitor in series in a very short time of around 290 $\mu$ s, and full contact separation is achieved 1.5 ms after the trip signal. It is recommended that the module design should primarily consider maximizing the number of break points in series. [ABSTRACT FROM AUTHOR]

Replacing SF6, the most potent greenhouse gas, with an alternative gas is a challenge faced by medium-voltage load break switches (MV-LBS). Air is a possible alternative, but there are some challenges regarding low dielectric strength leading to high arcing time and dissipated energy. Therefore, understanding the switching processes for both interruption and making operations in air MV-LBS is crucial to designing efficient compact switchgear. This work focuses on making operations in air MV-LBS. A synthetic test circuit and a model switch are designed based on the standards to simulate making operations under fault conditions similar to a real test. The test condition is set to achieve high pre-strike arcing time and energy. The results show that the most destructive impact of the making short-circuit current occurs in the first half-cycle of the load current when the pre-strike arc is formed. For an average short-circuit current with a peak of 22 kA and a breakdown voltage of 20 kV, the switch failed to re-open due to the arcing contacts welding after four successive making operations without main contacts and seven successive operations with main contacts. It has been shown that the total arcing contact mass loss occurs mainly during the pre-arcing time.Increasing the closing speed could be a possible solution to minimize the impact of arcing. [ABSTRACT FROM AUTHOR]

This letter presents a Space Vector Pulse Width Modulation (SVPWM) strategy for reducing the DC-link current harmonics in a multi– Voltage Source Inverter (VSI) topology with common DC-link bus. The DC current harmonic reduction is achieved by phase-shifting the PWM pattern of individual VSIs, with the inverters sharing the system total power. Simulation and experimental results are shown to validate the proposal. [ABSTRACT FROM AUTHOR]

The reignition probability of switching overvoltage caused by vacuum circuit breaker (VCB) switching off shunt reactor (SR) in offshore wind farm (OWF) is studied. Firstly, a model of OWF is developed in the environment of electromagnetic transient program. According to the switching time of VCB, a current period is divided into non-reignition zone, reignition zone and current chopping zone. Based on the analysis of overvoltage mechanism, a method for calculating critical arcing time and reignition probability is proposed. Then, the effects of resistor-capacitor (RC) snubber on reignition probability are discussed. The capacitance of RC snubber is optimized based on switching dispersibility of VCB and critical arcing time, and a new structure of RC snubber is developed. Finally, the hybrid method of RC snubber with new structure and phase-controlled switching is presented to suppress the switching overvoltage. The results indicate that the method can eliminate the reignitions and weaken the impact of overvoltage on the insulation of power apparatus. [ABSTRACT FROM AUTHOR]

Searching for SF6-substitute gaseous dielectrics is currently an urgent task for high-voltage circuit breaker (HVCB) insulation and arc extinction applications. Once leaked, SF6 will affect the Earth's climate on the order of decades to millennia. In this work, we developed a test method that supplies a series of extended pulse voltages to obtain the dynamic dielectric strength of C3F7CN/CO2 and C3F7CN/N2 gas mixtures that are potential SF6 alternative gases in an HVCB during its no-load closing-opening processes, by measuring the dynamic breakdown voltage between the contacts. We also investigated the closing pre-strike and opening insulation characteristics of these gas mixture HVCBs at different voltage polarities, C3F7CN concentrations and pressures during the processes. We experimentally found an obvious “low-voltage-breakdown” phenomenon and much higher dispersion in the dynamic breakdown voltage of C3F7CN gas mixtures compared with pure SF6. Moreover, the dispersion in closing was significantly higher than that in opening, leading to the closing pre-strike characteristics of an HVCB filled with C3F7CN mixtures that are inferior to SF6. The results not only provide a criterion via data but also evaluate the interruption gap design and give insight into the expected performance of the interruption chamber during breaking capacity tests. [ABSTRACT FROM AUTHOR]

This study addresses the issue of identifying the most suitable retail electric provider plan for the residential customers that are consumers only as well as consumers who intend to become prosumers. The main objective is to develop a methodology that will assist the residential customers in identifying the most suitable distributed energy resources, such as rooftop solar photovoltaic and home battery storage as well as electric vehicles. Furthermore, the proposed methodology is used to develop a decision support tool that aims to determine the appropriate retail electric provider plan that will ensure maximum savings on the customer's energy bill. The results of implementing the proposed methodology on case studies from Texas have shown that the residential customers can achieve significant savings if they install rooftop solar photovoltaic. The results have also shown that the maximum savings are usually associated with the time-variant or time-invariant plans, in case of customers with low energy usage, reaching up to $221/year. On the other hand, the customers with high energy usage were found to achieve significant savings on their energy bills when they are on the tiered time-invariant plans, in which case the savings may reach up to $475/year. [ABSTRACT FROM AUTHOR]

A spatial approach for calculating phase-to-phase switching impulse critical flashover voltage of overhead transmission lines is implemented using the Fourier enhanced charge simulation method (FEnCSM). Cathode-directed leader and streamer characteristics are used in an engineering model of pre-breakdown conditions. Rather than identifying breakdown based on complete bridging of the air gap, the proposed method identifies breakdown based on the ability of the leader-streamer system to survive the region of minimum electric field between phase conductors. Use of the minimum field as a basis for identifying breakdown allows anode-directed negative streamers to be reasonably neglected. Combined with FEnCSM, the proposed approach enables explicit representation of phase bundle subconductors and avoids the electrode-specific geometric constants or gap factors common in existing methods. Results obtained with the method compare well to four independent sets of experimental data for phase-to-phase flashover from the literature. The method was developed to facilitate ongoing research into practical use of the electric field as a basis for unifying electrical studies in the design of overhead transmission lines, including HSIL and other novel configurations. [ABSTRACT FROM AUTHOR]

A 10 kV vacuum circuit breaker (VCB) experiences prestrikes when its contacts are closing. Prestrikes can cause a high frequency (HF) and steepness overvoltage, which compromise the insulation of electrical devices. The transient prestrike process should be accurately simulated to effectively design and evaluate overvoltage suppression measures. The improved prestrike model was modeled in ATP-EMTP based on on-site measurement prestrike data. The model was applied to compare various overvoltage suppression measures in terms of the effectiveness. The simulation results showed that an RC snubber and a surge arrester can be installed to suppress the overvoltage amplitude on the substation transformer (ST) and shunt reactor (SR) sides. The RC snubber can reduce the oscillation frequency of the overvoltage compared with the surge arrester. Finally, the RC snubber and surge arrester were installed on the ST and SR sides as part of a field test to verify the simulation results. Reasonable suggestions are provided for switching overvoltage suppression through the simulation and experimental results. [ABSTRACT FROM AUTHOR]

The carrier-based pulse width modulation (CBPWM) with zero-sequence component injection is equivalent to the space-vector PWM (SVPWM), and hence it can be taken as a simplified alternative to the SVPWM. However, it is quite complex to calculate the zero-sequence component in CBPWM for three-level (3L) converters such as the T-type converter, making the 3L SVPWM still have a large computation burden. In this letter, unified expressions for the zero-sequence component are analytically derived, and the modulation waves of 3L SVPWM can be directly calculated by only 7 simple equations with 3 steps. The computation burden for implementing 3L SVPWM is therefore significantly reduced without sector determination, calculation and assignment of dwell times. [ABSTRACT FROM AUTHOR]

The reliability of meshed DC grids mainly relies on their ability in DC fault protection and line power flow managing. Multiple DC circuit breakers (DCCB) and current flow controller (CFC) need to be installed, which significantly increases the system cost. A novel current flow controller integrated with hybrid dc circuit breaker (CFC-IHCB) is proposed to significantly reduce the loss and cost of the whole system. Only one unidirectional IGBT string based main breaker branch is needed for n lines, and the CFC function is integrated into the load communication switches (LCSs). The basic working principle of proposed topology is presented and analyzed. The functionality is verified and a comparison of the proposed solution and other DCCB/CFC solutions is given based on a multi-terminal HVDC system case study. [ABSTRACT FROM AUTHOR]

In a photovoltaic (PV) DC integration system, a DC line-to-line short-circuit fault will cause all converters to be quickly locked. This can result in the sustained outage of the system. In this study, to address this problem, a protection method based on incipient fault identification is proposed to quickly identify and isolate the faulty branch, and to prevent the incipient fault from developing into a short-circuit fault. By analyzing the frequency characteristics of the incipient fault current, a disturbance injection start criterion is formed. Then, by using the converter to inject small disturbance signals to form obvious fault characteristics, the location and isolation of the faulty area can be achieved in time. The loop simulation results based on real-time digital simulator (RTDS) hardware demonstrate that the proposed method accurately recognizes the incipient fault without affecting the system power quality, and can simultaneously isolate the incipient fault. These factors provide guarantees for the safe and efficient operation of PV DC integration systems. [ABSTRACT FROM AUTHOR]

To improve current-interruption performance, spiral electrodes were experimentally investigated to magnetically drive an arc. Arcing times for conventional plane electrodes and spiral electrodes were obtained from conducting current-interruption tests and compared. The comparison results indicate that the arcing time in spiral electrodes is about one-third shorter than that in plane electrodes when interruption current is above 900 A. To clarify the principle of improving interruption performance, arc parameters, electrode erosion, and rate of increase in transient recovery voltage were compared for both plane and spiral electrodes. These results revealed that the magnetically driven arc enhances thermal loss of the arc and heat exchange between the arc and ambient gases. Regarding the spiral electrodes, the recovery rate of dielectric strength between the contacts was high. It is thus concluded that current-interruption performance improves by cooling the arc and increasing the dielectric strength by the magnetically driven arc. [ABSTRACT FROM AUTHOR]

The effect of splitter plates (SP) on current interruption at medium voltage (MV) level is theoretically investigated in the framework of Mayr's arc model, which is generalized to take into account the electrode fall voltage, V0, of the SP. The model is analytically solved in the current zero (CZ) region where the current (before CZ) and the voltage (after CZ) can be linearized with respect to time. The current turns out to be successfully interrupted if the total electrode fall voltage, NV0, for N − 1 SP plus contact electrodes, is larger than twice the transient recovery voltage, ${\boldsymbol{U}} \approx {\dot{\boldsymbol{U}t}}$ , at the characteristic arc decay time, t = τ, after CZ: ${\boldsymbol{N}}{{\boldsymbol{V}}_0} > 2{\dot{\boldsymbol{U}\tau }}$. For ${\boldsymbol{N}}{{\boldsymbol{V}}_0} < 2{\dot{\boldsymbol{U}\tau }}$ , an additional thermal condition must be satisfied, where also the current rate, ${\dot{\boldsymbol{I}}} = {\boldsymbol{\ dI}}/{\boldsymbol{dt}}$ before CZ, and the arc cooling power, K, are involved. The intuitive results lead to a simple understanding of the electrical effect of SP on current interruption at MV and serve as an initial design rule for the number of SP in different gases. [ABSTRACT FROM AUTHOR]