Search

Line-commutated converters are extensively used as the interface between ac grids and classic HVDC systems. At the inverter side, commutation failure of switches is one of the most common faults that can pose threats to the system operation. Practical and reliable study of such phenomena relies on accurate and efficient converter models for simulations. Recently, a parametric average-value model (PAVM) has been presented for ac–dc rectifiers, which considers the internal faults of the converter. In this paper, the PAVM methodology is extended to the dc–ac inverter systems, including the commutation failure of switches. The proposed PAVM also augments an automatic fault detection technique to determine the faulty switches. Using comprehensive simulation studies, the developed model is verified to accurately predict the commutation failure of switches and reconstruct the waveforms consistent with the detailed switching models of inverters while being computationally more efficient. The proposed PAVM is envisioned to be an efficient and accurate asset for simulation of HVDC systems and inevitable when faults of switches need to be considered. [ABSTRACT FROM AUTHOR]

VSC-HVDC systems are being increasingly employed in the power systems. The recently installed HVDC systems have a power capacity similar to traditional power plants. Hence, they are expected to have a similar behaviour as traditional synchronous generators during faults in AC grid, within their limits of course. Recent grid codes require HVDC converter stations to incorporate fault ride-through (FRT) capabilities in order to avoid HVDC converter station disconnection from AC grid for certain fault characteristics. In this paper, two FRT mechanisms are suggested for the two converter stations of an HVDC system. One FRT mechanism is added to the DC voltage control loop of the master converter station, while the other FRT mechanism is added to the active power control loop of the slave converter station. The objective is to ensure the stable operation of the HVDC system during faults that may occur in AC grids located on both sides of the HVDC system. The performance and stability of the suggested FRT mechanisms are tested considering the pre-fault power flow direction and all possible types of balanced and unbalanced faults. Simulation results confirm the effectiveness of the FRT mechanisms and revealed the critical modes during FRT operation. [ABSTRACT FROM AUTHOR]

In a previous paper (Part 1) the authors have performed the simulative evaluation of the life lost by HVDC extruded cables subjected to long TOVs occurring in VSC HVDC cable systems. The conclusions were that it cannot be completely ruled out that the field levels and the duration of such TOVs are a potential threat to certain cable designs, and tests other than Load Cycling Type Tests after CIGRÉ Technical Brochure 496 could assess quantitatively the potential threat associated with long TOVs. For these reasons, in this Part 2 superimposed switching impulses applied during Type Tests after TB 496 are analyzed in order to check if such impulses might be equivalent to long TOVs as for their electro-thermal stress effects on extruded insulation. The analysis is similar to that carried out for long TOVs in Part 1, i.e., it consists of: calculating the electric field during superimposed switching impulses; comparing it with the field during long TOVs; calculating with Miner's law of cumulated damage the life lost during superimposed switching impulses and comparing it with the loss of life during TOVs. A brief literature survey of potential high field effects during long TOVs is also reported. [ABSTRACT FROM AUTHOR]

Medium voltage direct current (MVDC) power systems are in their early phase of development, but the lack of efficient and reliable DC circuit breakers is currently one of the most significant bottlenecks for widespread adoption of MVDC applications. Compared to protection devices in high voltage direct current (HVDC) systems, MVDC circuit breakers are expected to interrupt fault currents with higher rates of rise in more power-dense and more controllable structures. A hybrid approach with a piezoelectrically actuated fast mechanical switch in parallel to a solid-state circuit breaker is expected to meet the above requirements. A prototype of a 15 kV-class piezoelectrically actuated fast mechanical switch is presented in this paper. The prototype demonstrates an actuator opening time of 1 ms, a breakdown voltage of over 20 kV, and a continuous current rating of 500 A. After integrating the fast mechanical switch into a hybrid circuit breaker testbed, the fast mechanical switch was able to open within 1.5 ms and the fault was cleared within 5 ms. Therefore, piezoelectrically actuated fast mechanical switches can enable fast, reliable and controllable protection for various MVDC systems like electric ships, electric aircraft and microgrids that integrate distributed energy resources. [ABSTRACT FROM AUTHOR]

In a line-commutated converter based high-voltage direct-current (LCC-HVDC) system, the inverter control system usually includes constant extinction angle (CEA) controller, constant current (CC) controller, current error controller (CEC), and voltage-dependent current order limiter (VDCOL). However, the interaction influence of multiple controllers may cause repetitive commutation failure (CF). For this purpose, this paper deeply investigates the mechanism and the influencing factors of repetitive CF caused by controller interaction. It is found that the lower limit value of CEA controller can affect the control switching process and thus the probability of repetitive CF. Besides, the minimum gamma measurement (MGM) unit prevents the system from acquiring the real extinction angle in time, which results in the DC current fluctuation during the recovery process. Moreover, the probability of control-induced repetitive CF is much higher when the HVDC inverter is connected to a weak AC system or the AC fault is not serious but not cleared in time. Based on the above analyses, an improved control method is proposed for recovery performance improvement, which is mainly realized by modifying the lower and upper limits of the CEA controller during recovery. Finally, the simulation and experimental results verify the theoretical analyses and the proposed control method. [ABSTRACT FROM AUTHOR]