Search

This paper summarizes the work performed by the Task Force —within Performance Characteristic Subcommittee of IEEE PES Transformers Committee— to investigate potential revisions to IEEE Std C57.142-2010. Although the scope of this document does not implicitly exclude HV and EHV systems, the existing document primarily includes examples and information on distribution voltage systems. A Task Force was formed to investigate the need to include information about power system transient events on HV systems more explicitly in this existing document. The Task Force was charged with the following tasks:-Establish system voltages encompassed by C57-142-2010 Guide. -Gather field data, reports, and literature on HV and EHV failures related to substation transients and transformer interaction. -Solicit input from the other technical committees on this subject. -Review IEC and CIGRE work in this area. -Recommend course of action on revision of the present Guide. -Recommend high level changes to the Guide. -Prepare final paper for the Subcommittee. In the course of this work several failure scenarios were identified. These are categorized and the failures are described in this paper. The final recommendations to the Subcommittee are summarized and recommendations are presented for the course of action on the revision/addition of HV and EHV material to the current C57.142 Guide. [ABSTRACT FROM AUTHOR]

Different from typical circuit breakers, breakers used to switch AC filters in convertor stations have to operate frequently according to the real-time operation mode and daily load changes. Therefore, the performance of filter breakers decreases very quickly, which leads to frequent accidents. Both preinsertion resistors and controlled switching devices can suppress switching transients. In this paper, a comparative analysis of whether a controlled switching device and preinsertion resistor should be adopted is carried out using PSCAD. The transient is calculated as the combined result of the switching angle and preinsertion resistor value, and the optimal configurations are proposed. After determining the resistor value and whether a controlled switching device should be included, the reference voltage of the arrester should be reevaluated. [ABSTRACT FROM AUTHOR]

Aging of power system assets challenges utilities to maintain reliable service while minimizing their maintenance costs. Although malfunction of devices in the transmission or distribution networks can have catastrophic consequences, their failure is seldom unforeseen. Typically, the device aging occurs gradually over time until its health condition reaches a point of complete breakdown. The overall objective of this paper is to devise a non-invasive, online condition monitoring technique of circuit switchers for shunt capacitor banks. It aims to detect abnormal operation of these devices based on features derived from raw voltage and current waveforms, such that a predictive maintenance strategy may be employed before a complete failure occurs. The data analyzed in this paper are collected at a transmission capacitor bus, where the banks are equipped with pre-insertion impedance. Through a baseline range of values for selected parameters, the proposed technique is able to detect missing pre-insertion impedance during the capacitor energizing and failure of pre-insertion impedance switch out a few cycles after the energizing operation. [ABSTRACT FROM AUTHOR]

Transient voltage and current stresses are essential for the design and protection of multi-terminal DC (MTDC) transmission systems, especially under the short-term dynamics after severe grid faults. In this paper, we propose a discrete-time model for the modular multilevel converter based MTDC (MMC-MTDC) system considering the DC-side disturbances in the system. Based on the piecewise linear modeling, the state variables such as the transient voltage on the sub-module (SM), arm current, etc., can be calculated analytically for the critical short term (within 10 ms) after the severe DC fault while the system protection is yet to be activated. Parameter sensitivity analysis is also performed to give a better system design guideline. The estimation results are validated by detailed electromagnetic (EMT) circuit simulations and the scaled-down experimental laboratory prototype. [ABSTRACT FROM AUTHOR]

Fast and detailed calculations of harmonics, generated by three-phase uncontrolled rectifiers with finite dc smoothing, can be performed by using detailed analytical procedures (DAPs). Several DAPs are developed for continuous- and discontinuous-conduction modes (CCM and DCM) when balanced operation of the system is assumed. The authors of this paper have recently proposed a new DAP (model 1a) in which nonideal conditions, such as unbalances and even harmonic voltages on the ac side, are taken into account. However, only CCM is assumed in model 1a. The main objective of this paper is to overcome this limitation of model 1a so that a new DAP (model 1b) for DCM is presented, which is capable of considering unbalanced operation. Moreover, the boundary of the DCM is also estimated for model 1b under nonideal conditions. [ABSTRACT FROM PUBLISHER]

Switching of shunt capacitors can cause transient overvoltage. The voltages are traditionally evaluated with electromagnetic transients (EMT) simulation programs. It is a very time-consuming process mainly due to the need to convert a power-flow (or short-circuit) case to the EMT case. This paper proposes an idea to conduct capacitor switching studies directly inside commercial power-flow/short-circuit tools such as PSS/E, thus avoiding the data-conversion process. The idea is to conduct switching studies in the frequency domain. The frequency response of the study network is determined using the short-circuit solution engine of the host commercial software. This paper presents the theory, unique issues, and implementation details of the idea. The effectiveness of the proposed method is verified by comparing the results with those of the EMT simulations. [ABSTRACT FROM PUBLISHER]

A novel scheme is proposed to monitor the operation of capacitors scattered in MV distribution systems. It first codes each capacitor with a distinctive switching character by setting a unique combination of a three-phase switching order and time interval. As a result, the transient of the three-phase reactive power during capacitor switching will appear in a unique way. Then, the reactive power disturbances monitored in the substation are decoded to identify which capacitor is being switchedonandoff. A detailed decoding method is developed to realize this identification without being impacted by the switching interference of loads and other reactive power compensation devices. Moreover, the implementation of the proposed scheme in the field is elaborated, and the resultant three-phase voltage unbalance is analyzed in this paper. Compared with existing methods, this scheme only requires one power quality monitor located at the substation to monitor the operations (energizing or de-energizing) of downstream distribution capacitors without extra communication devices. The operation information is valuable for tackling power quality problems caused by capacitor switching and optimizing the distribution grid operation. [ABSTRACT FROM AUTHOR]

This paper highlights an immediate need for renewable generation developers, manufacturers, utilities and industry standardization institutes to jointly address a challenge of capacitor switching transient immunity in inverter-based wind or solar farms. The need was identified from wide-area operation records which showed partial or full generation loss in coincidence with routine utility-owned capacitor switching. The lack of a clear industry guideline has caused confusion to all involved parties. This paper recommends all entities to address this challenge collaboratively through enhanced equipment specification, design, and test before a well-defined industry guideline becomes available. [ABSTRACT FROM PUBLISHER]

The model of a modular multilevel converter (MMC) determines the extent of critical circuit information that electromagnetic transient simulations can reveal. In this paper, two MMC models are proposed for efficient real-time hardware-in-the-loop (HIL) emulation on the field-programmable-gate-arrays (FPGA). The nonlinear switch-based model employing the insulated-gate bipolar transistor (IGBT) dynamic curve-fitting model considers factors affecting its transient performance so that device-level behavior such as power loss and junction temperature can be reproduced accurately in the electro-magnetic-thermal simulation of a power converter for its design evaluation. Meanwhile, regarding the MMC submodule as a transmission line stub achieves faster computation speed and enables the formation of a hybrid arm to save FPGA hardware resources. As the large network that the MMC presents is burdensome for real-time execution with a small time-step, circuit simplification based on partitioning and merging is conducted. Hardware implementation of a three-terminal high-voltage direct-current system containing an MMC-based dc–dc converter is carried out and the efficacy of proposed models is validated by comparing HIL emulation results with the offline simulation tool PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

Shunt power capacitors are essential to system operation and reliability as a critical reactive power source to increase system capacity, support voltage magnitude, improve power quality, and reduce reactive current flow. To mitigate capbank switching transients, the synchronous switching with preinsertion resistor technology is developed and used at an extra-high voltage transmission system. In this paper, the coupling relationship between several key factors that contribute to switching transients is studied. Optimization solutions are developed to improve the switching process. Field operations with an updated setting are compared with original setting records to prove the correctness of the study. [ABSTRACT FROM PUBLISHER]

Capacitor switching transients are harmful to the capacitor and the switching device. For reducing these transient phenomena, this paper proposes a symmetrical structure transient limiter (SSTL). The proposed SSTL can automatically provide high impedance at the instant of capacitor energization, and, thus, the switching transients can be effectively suppressed. After the restriction, owing to the compensation of all power losses caused by the diodes and reactors, the SSTL acts as a short circuit during the steady state and, thus, has no effect in the circuit. As a result, the capacitor voltage and current waveforms will not be distorted. Moreover, due to the freewheeling effect in the SSTL, no transient overvoltage will appear across the switch contacts at the instant of capacitor de-energization even though the reactors are inserted into the circuit. Theoretical analyses of the proposed SSTL for the energization state, steady state, and de-energization state have been completely carried out. Also, the selections of the related components are depicted. Finally, the experimental results obtained using different methods of capacitor switching verify the feasibility and performance of the proposed SSTL. [ABSTRACT FROM AUTHOR]

Numerical overcurrent relays used to protect capacitor banks can better discriminate between faults and switching inrush compared to their electromechanical counterparts. However, there is still scope and use for faster and reliable operation. This paper describes the implementation of a filter based on mathematical morphology that creates distinct signatures for capacitor inrush and faults. These signatures are then used to propose a rule-based classification method that can be easily implemented in microprocessor-based relays. Extensive simulations are carried out to test the classification method using waveforms generated from PSCAD/EMTDC simulation of a standardized test system. The classification method is shown to be very reliable, general, and significantly faster than methods currently used or previously proposed. [ABSTRACT FROM AUTHOR]

This paper describes two new approaches for the determination of the direction of switched capacitor banks as well as an efficient technique for estimating the distance of switched capacitors from the monitoring location in distribution systems. At first, two new indices based on branch voltage and current changes immediately after the capacitor switching instant are proposed for determining the direction of switched capacitor banks. The wavelet transform is used to detect the exact instant of switching. Then, a new technique based on linear circuit theory is proposed to estimate the distance of the switched capacitor bank from the monitoring location using capacitor switching transient data. Simulation results show that the error of the estimated distance is acceptable. A combination of the approaches for direction finding and the technique for distance estimation provide a novel method for determining the location of switched capacitor banks in real distribution systems. The method is valid in all normal, back-to-back, and abnormal switching of wye- and delta-configured capacitor banks. Also, the size of the capacitor bank has no effect on method accuracy. The efficacy of the proposed method is validated by using the IEEE 13-bus and 34-bus distribution systems. [ABSTRACT FROM AUTHOR]