Search

The medium-voltage grid is often planned in loops, but operated in a radial structure to allow a robust protection scheme. This allows the reconfiguration of the grid. This paper focuses on reconfiguration after a fault to re-establish the service, also referred to as self-healing. It includes the localization of faults and finds new grid configurations based on the actual status of the grid. The solving of the reconfiguration problem is nonpolynomial difficult. Finding an acceptable solution to resupply nonfaulted grid parts under tight time limits is difficult. The innovative contribution of this paper is an approach that finds new configurations as local as possible to the faulty area, evolvingly increasing the search space. New configurations are generated based on a heuristic method relying on graph theory. An aggregated fitness function is used to evaluate the solutions. For the realization, a distributed control architecture in the form of an advanced substation automation is proposed. [ABSTRACT FROM PUBLISHER]

Single-phase autoreclosing (SPAR) is among the alternatives for mitigating the many harmful effects that a line-to-ground fault in a transmission line (TL) may cause. This procedure basically consists of opening the compromised phase, waiting a preset time span (dead time), and recomposing the previously isolated phase. In the vast majority of SPAR implementations, the open phase switching proceeds with no guarantee of whether the TL is still faulted. Switching the open phase into a fault might represent a more severe threat to the system than simply disconnecting the TL in the first place. Hence, in an effort to ensure higher levels of operational reliability to SPAR, the present paper offers a new methodology to check the soundness of the open phase during the dead time before its reclosing. First, the method's fundamental concepts are exposed. Second, a huge number of steady-state tests are presented, for which both the system topology and its operative condition were varied. To conclude, the SPAR is simulated in the time-domain with the most critical condition found in the steady-state analysis. The proposed strategy was capable of correctly identifying whether the system was faulted in every performed simulation. [ABSTRACT FROM AUTHOR]

This paper proposes a modified bridge switch-type flux-coupling nonsuperconducting fault current limiter (BSFC-NSFCL) for suppressing the fault current and voltage sag. A flux-coupling reactor and a bidirectional bridge switch are combined to perform the functions of steady-state line current sharing and fault current suppression. The modified BSFC-NSFCL mainly utilizes the magnetic flux cancellation effect to make the limiter behave as a short circuit on the circuit during normal operation. Hence, there is almost no impact on the power system when the limiter is used. When a fault event occurs, the bridge switch turnsoffimmediately, and then, the magnetic flux cancellation effect disappears. Thus, the impedance of primary coil inserts into the circuit to restrict the fault current and voltage sag phenomena. Once the fault is removed, the bridge switch turnsonagain, and the BSFC-NSFCL recovers to the normal operation. The modified NSFCL is more cost-effective and easy to be implemented than the flux-coupling superconducting fault current limiter. Theoretical analysis for the BSFC-NSFCL has been fully developed and proven by MATLAB software. Finally, the analytical, simulated, and experimental results have been carried out to verify the feasibility and performance of the proposed BSFC-NSFCL. [ABSTRACT FROM AUTHOR]

In this paper, a static synchronous compensator (STATCOM) operation scheme of the modular multilevel converter adopting clamp double submodules (CDSM-MMC) during a pole-to-pole dc fault is proposed. By analyzing the current paths of a CDSM, this paper proposes three new operation states of the CDSM, which allow the CDSM to provide bipolar voltages when the arm current that flows through it is negative. Through control of the CDSMs to operate in these new states along with the blocked state, the arms of the CDSM-MMC can operate alternately in two different modes, that is, the conducting mode and blocked mode even when the dc-link voltage drops to zero. Thus, the CDSM-MMC is capable of working as a STATCOM during a dc fault. Moreover, a control strategy of the dc-fault STATCOM operation mode is designed to control the reactive power provided by the CDSM-MMC, to limit the dc fault current, and to reserve and balance the energies stored in capacitors. Simulation results conducted in PSCAD/EMTDC demonstrate the validity of the proposed STATCOM operation scheme and control strategy of the CDSM-MMC during a pole-to-pole dc fault. [ABSTRACT FROM AUTHOR]

This paper presents a breaker arrangement concept, the multiline breaker (MLB), for the protection of multiterminal high voltage dc (MTdc) networks. Based on the design of a hybrid breaker, the MLB is an economically attractive solution for the protection of multiple dc lines in nodal connection using a single main breaker path. By using commutation units, the MLB directs the fault current through the main breaker in a unidirectional way, irrespective of the fault location. Hence, this study presents the design requirements for the MLB, regarding both hardware and control, and evaluates its operation within a grid. For this reason, a four-terminal half-bridge multilevel modular converters-based MTdc grid in radial configuration was used and pole-to-ground dc fault conditions were investigated. The dc fault response of the grid with one MLB at the central node is compared to the respective response of the grid when one hybrid breaker is employed at each dc line. The simulations show that the MLB is feasible and that the overall MTdc grid fault response for the two protection systems is very similar. As a result, the design advantages of the MLB make it a promising solution for the dc fault isolation in MTdc grids. [ABSTRACT FROM AUTHOR]

The modular multilevel converter-based unified power flow controller (MMC-UPFC) is able to operate under unbalanced grid conditions with symmetric component decoupling. However, the constraint of the voltage limit of UPFC is not considered and no protection schemes are investigated to protect the UPFC from overmodulation under unbalanced grid conditions. To solve this problem, this paper proposes the cascaded control scheme for MMC-UPFC based on voltage limit control and symmetric component decoupling to balance the ac current of the transmission line. With appropriate transformer connections for MMC-UPFC, the negative- and zero-sequence currents are suppressed by the corresponding inner current loops. Considering the voltage limit of MMC, the operating ranges of UPFC-MMC under balanced and unbalanced grid conditions are investigated in both mathematical derivation and point scanning methods. The results are depicted and analyzed in 3-D vision. Based on the analysis of operating regions, the voltage limit control is proposed to protect the MMC from overmodulation and to maximize the controllable region under unbalanced grid conditions. Finally, the final cascaded control structure is constructed. The simulation results obtained in PSCAD/EMTDC are provided to validate the effectiveness and robust performance of the proposed control strategies. [ABSTRACT FROM AUTHOR]

The ground return current of a high voltage direct current system will intrude the transformers adjacent to the grounding electrode in the case of monopole operation, leading to the half-cycle saturation of transformers. To mitigate the adverse effect, placing dc blocking devices (BDs) in transformer neutrals is popularly advocated. The conventional switching method of BDs may redirect the dc flow from one transformer with a BD to neighboring transformers without BDs. In this case, the dc currents through the neutrals of those transformers may possibly exceed the threshold undesirably. This problem is due to the lack of guidance for dc current distribution from the global view by means of finite BDs. Thus, this paper presents an optimization approach for the switching of BDs based on the gravitational search algorithm. A mathematical model for investigating the dc global distribution is established with the equivalent resistive network of an ac system, the location distribution of substations and grounding electrodes. Then, an optimal switching scheme to minimize the adverse impact of dc bias is presented, and the principle and the concrete implementation process are detailed. The feasibility and the advantage of the proposed scheme are demonstrated by numerous comparative case studies. [ABSTRACT FROM AUTHOR]

This paper proposes a novel bridge-type solid-state fault current limiter (BSSFCL) based on one series reactor which operates in ac and dc modes. The proposed BSSFCL includes a rectifier bridge with a reactor. This reactor is used as a dc reactor in normal operation mode and as an ac reactor in fault conditions. The advantages of the proposed BSSFCL over the existing dc reactor-type FCLs are its negligible impedance in normal operation mode and its high impedance during a fault interval using simple and novel switching. In other words, during the normal operation mode, the proposed BSSFCL operates in dc mode and in the fault interval, its topology is changed to the ac mode. This switching decreases the switching transient recovery voltage and introduces considerable impedance during the fault period. MATLAB/Simulink software is used for simulations and a prototype is designed and tested for results verification, and to show the performance of the proposed BSSFCL. [ABSTRACT FROM PUBLISHER]

This paper presents a novel mitigation technique to reduce the effects of geomagnetically induced currents (GICs) on high-voltage power systems. The method consists of connecting switching devices at the neutral grounding connection point of transformer banks. Only one transformer bank needs to be grounded through a switch to reduce GIC in a two-terminal system. For multiterminal systems, n-1 switches are necessary and the operation is independent from each other. The switching frequency and the duty cycle are selected from a tradeoff between the effectiveness of the method and the detection of fault currents. Transient simulations on a two-bus 230/500 kV system show that the proposed switching at the neutral successfully mitigates the GIC. This proposed technique opens the door to a new family of GIC mitigation methods. [ABSTRACT FROM AUTHOR]