Search

This paper presents an economic study to find the switches that should participate in a switch upgrade plan, based on the results of reconfiguration. The traditional reconfiguration problem trend considers only one loading condition (mostly maximum demand), in order to find the optimum reconfiguration. However, as the distribution loading condition has hourly and daily variations, the optimum configuration continuously changes. Consequently, considering only one loading condition might lead to inefficiency of the results. In this paper, daily load curves of different types of distribution consumers, during various types of days (weekdays and holidays) and seasons (summer and winter), are used to obtain the best reconfiguration hours during a day. Then, genetic algorithm (GA) is used to obtain the optimum configuration during each time interval. The objective function applied to GA consists of loss and energy not supplied. The switches that contribute to reconfiguration should be remotely controlled in order to have the capability of immediate mode alteration. In order to evaluate the feasibility of automated switch installation, the benefit-to-cost ratio is calculated. The entire procedure is applied to a test distribution system, and the results are discussed in this paper. [ABSTRACT FROM AUTHOR]

Future multi-terminal dc networks are envisioned for the large-scale integration of renewable energy sources into today's power systems. An essential aspect for the reliable operation of these systems is the fast and selective dc-side fault handling and separation of faulted lines. The objective of this paper is the development and evaluation of a multi-terminal dc protection strategy based on fault-blocking converters (e.g., full-bridge based modular multi-level converters) and high-speed switches. Both a suitable fault control and a new high-speed switch design for a fast separation of faulted dc lines are elaborated. The novel concept is intended to reduce the requirements on the high-speed switches compared to dc circuit breakers and to ensure a fast restoration of the active power transmission capability, as well as the dc voltage. The fault-clearing strategy is analyzed using electromagnetic transient (EMT) simulations under variation of the fault location, type, and resistance. The investigations are carried out in a cable-based multi-terminal HVdc system with full-bridge modular multi-level converters in symmetrical monopole configuration. [ABSTRACT FROM AUTHOR]

Insulation monitoring is crucial to personal safety and equipment operation in the power distribution system. Recently, with the rapid development of distributed generators, the three-phase voltage-source PWM converter (VSC) is widely used as the bidirectional interface between the dc microgrids and the distribution networks. This paper presents the relationship between the response of insulation monitoring device (IMD) and the neutral-point voltage deviation (NPVD) of VSC, by analyzing the disturbances of the switching function and the dc-side insulation balancing. Then, a method of detecting the NPVD for grid-connected VSC is proposed, based on the dc signal injection and the Duffing oscillator. Furthermore, the proposed method takes the mean and spectrum of the neutral-point voltage as the primal characteristics. Thus, the dc signal injection is adopted to detect the mean of the neutral-point voltage, and the Duffing oscillator is adopted to determine the frequency disturbance of the neutral-point voltage, respectively. The test result confirms the existence of the neutral-point voltage deviation and verifies the availability of the proposed method. Hence, the proposed method could be used to improve the response of IMD. [ABSTRACT FROM AUTHOR]

In Nordic countries, distribution networks are traditionally unearthed and increasingly compensated. For such networks, switching their neutral point to the earth is practically applied through a resistor for better selectivity functions of earth faults. In this paper, the neutral switching and, consequently, an arrival time of the aerial mode traveling wave reflected from the fault point are utilized to accurately determine the earth fault distance. A concept to create traveling waves is implemented by earthing the neutral via a controlled thyristor that provides a short period of high fault current and produces traveling waves to estimate the fault distance. Much higher transient signals are generated by earthing through an opposite charged capacitor. A capacitor-resistor divider is utilized to measure the reflected surge over a heterogeneous distribution feeder. An adaptive setting is proposed for stamping the arrival surge. The results provide evidence of the efficacy of the proposed fault distance estimation. [ABSTRACT FROM AUTHOR]

This paper addresses the subject of reducing outage durations and autorestoration applications within the distribution substation. Employment of intelligent electronic devices (IEDs) can aid in the reduction of the fault duration time, and also it enhances the protection, control, and monitoring at the distribution level. Further, communication among these IEDs can provide faster autorestoration, remote data analysis, event recording, etc. Many recent issues related to distribution substation protection are discussed and techniques to address these issues using current technologies are proposed. [ABSTRACT FROM AUTHOR]

In this paper, a new method is proposed that can be used to discriminate faults from switching transients. The method is primarily intended for use in systems where fast fault detection and fast fault clearing before the first peak of the fault current are required. An industrial system, in which high short-circuit power is desired but in which high short-circuit currents cannot be tolerated is an example of such a system. A phase-locked loop (PLL) is used to perform the discrimination. Computer simulations have been performed and it has been demonstrated that the output of the PLL is completely different for a fault compared to a switching transient. This difference can be used for discrimination between a fault and a switching transient. [ABSTRACT FROM AUTHOR]