Search

This paper presents an online method to monitor the conditions of the substation grounding grid. The proposed method utilizes phase-to-ground faults occurring in downstream feeders as test current sources and the neutral of a specially selected feeder as the electrode for GPR (ground potential rise) measurement. The measured fault currents and GPRs are then used to estimate substation grounding grid impedance. The method, once established, can monitor the grounding grid impedance continuously and automatically, and the trend of the impedance change can be observed. As a result, the proposed method can yield much more reliable information on the substation grounding conditions. The method also overcomes many disadvantages of the offline methods. The proposed idea, algorithm, and hardware setup are described in the paper. Factors contributing to measurement errors are investigated in detail. [ABSTRACT FROM AUTHOR]

The surface voltage of an insulator assumes importance for understanding tracking and flashover characteristics. Until now, determination of surface voltage of insulating surfaces is left to simulation software and such simulations are left unverified experimentally, leading to uncertainty of the results, which may sometimes be erratic with improper choice of boundary or initial conditions or inaccurate material properties, nonlinearities etc. The paper presents a novel method, using which the surface voltage of any insulating surface such as insulator strings or transformer bushings can be measured. Unlike a conducting surface, the measurement of insulating surface voltage using voltage dividers would be erratic as the measuring arrangement itself will vary the voltage division due to the local unknown impedance between the insulated surface and hv conductor. Recently a method for measurement of surface voltage of an insulated conductor using cylindrical strips was reported. In this paper, based on analytical derivations, a more generalized method of measurement, applicable to any point on an insulating surface of arbitrary geometry is proposed using circular-disc strips. The proposed experimental method is applied to insulator strings and transformer bushings and validated by simulation of the entire systems. The simulation and experimental results are in excellent agreement. [ABSTRACT FROM AUTHOR]

Electrical equipment of the floating nuclear power plant operates in a long-term vibration environment. Ground faults occur frequently and are often accompanied by arc, a reliable arc suppression algorithm for the generator stator winding is necessary. In this paper, an active arc suppression method is proposed by connecting a controllable voltage source to the generator neutral point. Through regulating the neutral point voltage to be equal in amplitude and opposite in phase to the fault potential, the fault point voltage can be clamped to a low level to achieve arc suppression. Since the generator's phase potential contains certain harmonic components, the controllable voltage source includes fundamental and third-order harmonic components. To accurately calculate the output voltage, online calculation methods for the fault location, fault potential and grounding capacitance are proposed. The accuracy of the fault location method is verified by simulation and dynamic test. And simulation results based on PSCAD/EMTDC software show that the proposed method can achieve effective arc suppression at different ground fault conditions. [ABSTRACT FROM AUTHOR]

Direct lightning poses a serious threat to the safety of power systems. In recent years, the lightning fractal model, which can reflect the fractal characteristics and randomness of lightning leaders, has been gradually applied to direct lightning protection for substations, transmission lines, etc. However, since few studies have linked simulations with experiments, the reliability of the lightning fractal model in terms of attachment probability prediction lacks experimental verification. In this paper, a series of attachment tests are carried out under a rod-rod gap. The equivalence between simulation tests and natural lightning is discussed, and the influencing factors of the attachment results are investigated. The attachment probability is simulated and compared to the test value under each test configuration. The test results show that the fractal dimension of discharge channel is consistent with the observation results of natural lightning. Under different configurations, the test value of attachment probability basically conforms to the simulation value. In general, the dispersion of the test results is slightly greater than the simulation results, but the average probability differences are all within 10%. The test results strongly indicate that the lightning fractal model is of good reliability in the prediction of strike probability. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

Phase–locked loop (PLL) is commonly used for the grid-connected voltage-source converter (VSC) to synchronize with the grid. Under weak grid conditions, it has been found that the frequency-dependent characteristic of the network impedance inherently introduces a positive feedback loop into PLL. Previous studies focused on the PLL analysis intuitively believe that the positive feedback loop will deteriorate the dynamic performance of the PLL. However, this conclusion is not rigorous since only the dynamic of the PLL is considered and the theoretical analysis is insufficiency to reveal the influence of the positive feedback loop on system stability. In this paper, the impact of the frequency-dependent network on VSC stability is quantified in terms of the overall system based on the damping torque analysis. It is found that the influence of the positive feedback loop on stability depends on the parameters of the PLL and the damping of the dominant eigenvalues. Besides, an angular frequency feedback scheme is proposed to eliminate the adverse effect of the frequency-dependent network and enhance the stability of the VSC under weak grid conditions. Time-domain numerical simulations and reduced-scale experiments are performed to validate the effectiveness of the proposed scheme. [ABSTRACT FROM AUTHOR]

This paper proposes a time-domain method of characteristics to simulate the impulse corona with background space charge, and derives the ordinary differential equations of the space charge generated by the impulse corona along the electric field line. The corresponding boundary conditions, the selection of time step and space step, and the update strategy of space charge are given. The calculation result of the impulse corona onset voltage is consistent with the test result, proving that the background space charge has almost no effect on the impulse corona onset electric field which is obtained by Kaptzov's assumption. The q-u curve obtained by simulation is compared with the test results to verify the effectiveness of the simulation method. The simulation method is used to obtain the development process of space charge during the application of the opposite polarity impulse voltage. By analyzing the space charge distribution during the process of impulse corona, and the corresponding microscopic charge distribution and macroscopic charge amount at different corona states, the characteristics of impulse corona are explained. [ABSTRACT FROM AUTHOR]

This paper proposes a novel layout for a grid-connected DC wind farm (DCWF) and investigates the performance under continuous operation and direct lightning strikes particularly for high soil resistivity. The DCWF employs internal dc grid that supplies generated power to the host AC utility through high voltage direct current (HVDC) transmission link. The proposed layout ensures sustainability of power supply against potential interruptions of DCWFs either during normal conditions or lightning incidents to comply with grid codes regulations. During continuous operation, the proposed layout safeguards the entire DCWF cables against flow of return currents to avert derating of conductor ampacity. Besides, protects WT nacelle switchgear and entire interface converters against hazards of surge currents. Furthermore, an effective grounding system design is proposed to introduce a low impedance path for system return currents, minimize voltage drop across grounding impedance and thus maximize DCWF delivered power to the grid. A detailed system that sufficiently represents models of system cables, grounding network and interface converters is built to verify the proposed scheme significance. The obtained results assure the capability of proposed layout to cease return currents via cable sheath during continuous operation and provide superior mitigation of lightning-associated transient voltages and currents. [ABSTRACT FROM AUTHOR]

An electric potential appears at floating wires located within a strong electric field. This phenomenon can be used to supply small isolated communities situated close to Extra-High Voltage transmission lines. This non-conventional distributed generation system has been studied for the last years. However, to improve the power generation system the optimal position of the floating wires, number of wires used, bundle radius, and type of wires must be properly identified. This paper presents a mathematical model solved with genetic algorithm to design a collector system with optimized induced voltage and minimized project cost, identifying the optimal reactor used for voltage regulation. The algorithm was applied to design a collector system that can tap-off 100 kW from a 230 kV transmission line. The trade-off between objectives and the Pareto optimal solutions were evidenced via several simulations using the weighting sum approach. These results allowed to identify a final geometry according to a-posteriori designer preferences. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

The impulse grounding performance of distribution lines tower is the key factor to lightning protection. Few field high-current impulse test researches are conducted on distribution line tower. In this paper, we used a mobile high-current impulse generator to conduct test on a 10 kV distribution line tower. The peak value of the current injection is 6 kA to 16 kA. The impulse impedance and the surface potential distribution are measured and analyzed. Based on the CDEGS software, an equivalent modeling of the experiment was carried out. The influence of soil ionization was taken into account by the method of changing the conductor radius through two rounds of calculation. The simulation and measured results were basically consistent. Experiments have shown that the soil ionization effect has an important impact on lightning performance of distribution line tower. The graphite earthing modules (GEMs) and pulling wires can significantly reduce the impulse impedance of the tower. The potential rise of the earth surface at a distance of 30 m from the tower can reach 1 kV at peak, under an injection of 7.15 kA. [ABSTRACT FROM AUTHOR]

High-frequency overvoltages are most dangerous for the insulation of transformer coils. It is because high-frequency pulse voltage creates an uneven distribution of voltage across the windings. The coil's first turns receive a disproportionately high voltage drop, leading to the inter-turn circuit. The paper analyzes the types of lightning pulses and proposes a new suppression method based on the anomalous skin effect in a multilayer material and the design in the form of a coil. The developed device is simulated, and the results of overvoltage monitoring at the substation with the installed high-frequency overvoltage suppression device are analyzed. [ABSTRACT FROM AUTHOR]

Electrical power connectors are critical points of electrical networks. Failure in high-voltage connectors may result in major power outages, safety risks and important economic consequences. Therefore, there is an imperious need to tackle such issue by developing suitable on-line condition monitoring strategies to minimize the aforementioned problems and to ease the application of predictive maintenance tasks. This work develops an on-line condition monitoring method to predict early failures in power connectors from data acquired on-line (electric current and voltage drop across the connector, and temperature) to determine the instantaneous value of the connector resistance, since it is used as a signature or indicator of its health condition. The proposed approach combines a parametric degradation model of the resistance of the connector, whose parameters are identified by means of the Markov chain Monte Carlo stochastic method, which also provides the confidence intervals of the electrical resistance. This fast approach allows an on-line diagnosis of the health condition of the connector, anticipating its failure and thus, easing the application of predictive maintenance plans. Laboratory results emulating the ageing conditions of the connectors prove the suitability and feasibility of the proposed approach, which could be applied to other power products and apparatus. [ABSTRACT FROM AUTHOR]

Voltage drop developed between the grounding electrode under lightning current and distant neutral ground determines the protection efficiency. The peak value of such voltage can be computed from known impulse impedance and current peak value. For the first time, in this letter, general formulas are derived for impulse impedance of horizontal and vertical electrodes valid for any length up to 100 m, soil's resistivity of 30 to 1000 Ωm, and current impulse front time of 0.2 to 10 μs. Waveforms of typical lightning impulses given in IEC standards are used, but it is shown that results are also relevant for other impulse waveforms. Soil ionization effects are taken into account, and the accuracy of the formulas is investigated. New formulas enable an estimate of lightning protection grounding's surge efficiency in a wide range of practical situations. [ABSTRACT FROM AUTHOR]

A new electromagnetic time-domain model dedicated to calculating the lightning response of electric systems and their components is presented. It is formulated taking as reference the main features of the frequency-domain Hybrid Electromagnetic Model. A differential aspect of this model is the capability to efficiently address problems involving nonlinear effects, such as soil ionization around grounding electrodes, the surge-arresters operation and the Corona Effect in applications related to the lightning performance of transmission lines. In addition, it is able to consider frequency-dependent effects, for instance that of soil resistivity, with an accuracy compatible with engineering applications. The basic formulation of the model is shown along with the validation of the results it yields by comparison with reliable references, including experimental results. [ABSTRACT FROM AUTHOR]

Many failures of wind turbine blades and electrical equipment due to powerful lightning strikes have occurred. The lightning-induced wind turbine failures that have occurred in recent years can be classified into two main categories. The first is a mechanical component failure. The second is a failure or malfunction of electric or electronic equipment inside or around the wind turbine due to an increase in the potential of the wind turbine grounding system or the electromagnetic induction caused by the lightning strike. In the latter case, the equipment often fails owing to the increase in the potential of the grounding system, the method of suppressing the potential rise by laying a grounding wire vertically or horizontally to the wind turbine foundation is adopted. We propose an empirical expression for the effective length of counterpoises connected to a large grounding electrode such as a wind turbine foundation, and verify the expression using finite-difference time-domain (FDTD) method. [ABSTRACT FROM AUTHOR]