Search

This paper exploits smart inverters of distributed energy resources (DERs) for the mitigation of fault-induced delayed voltage recovery (FIDVR). According to the IEEE Standard 1547-2018, smart inverters with voltage ride-through and var injection capabilities are promising technologies for mitigating FIDVR. This paper quantitatively investigates the effectiveness of smart inverters for FIDVR from a system-wide perspective. It shows that the penetration of smart inverters and induction motors are important factors affecting mitigation success. In addition, the over-voltages at the end of FIDVR due to load disconnections can be prevented with coordinated control of DERs and automated switching capacitors. The control scheme of smart inverters used for FIDVR is extended from the distributed volt/var droop control to include low- and high-voltage ride-through capabilities. The IEEE 13-bus feeder, the 8500-node test feeder, and the IEEE 390-node low-voltage network test system are used to illustrate the impact of DER penetration. For example, one can determine the residential air conditioner penetration level (for a given system at certain DER penetration level) that makes a system susceptible to FIDVR. The effects of solar intermittency are also studied. [ABSTRACT FROM AUTHOR]

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

This paper presents extensive verification, sensitivity, and application studies for an online substation grounding grid condition monitoring method proposed in a companion paper. The studies are conducted using a realistic substation grounding grid and associated feeder configurations commonly encountered in North America. The verification studies confirm that the proposed method is able to estimate the substation grounding impedances with acceptable accuracy. Main factors impacting measurement accuracy are identified and quantified through sensitivity studies. The findings lead to a guide for the implementation and operation of the proposed method. An application case is presented to demonstrate how the gradual deterioration of substation grounding grid can be monitored using the proposed method. [ABSTRACT FROM AUTHOR]

This paper addresses the interactions among the control loops of voltage-sourced converters (VSCs) embedded in high-voltage direct current (HVDC) systems and the impact of these interactions on the performance of individual control loops. Furthermore, this paper proposes a method to design the individual control loops, rather than the interconnected control system, such that the overall system stability is ensured in the presence of interactions. This paper addresses three aspects of the impact of control loop interactions on the overall control system of the VSC including stability, transient response, and steady-state response. To illustrate the impact of interactions on the VSC small-signal stability, stability regions of the interconnected control loops are obtained and compared against those of the various individual control loops. Then, a novel formulation of the VSC stability criterion is presented, and the small-gain theorem is utilized to determine a range of stabilizing gains for the interconnected control system. Moreover, new indices using the infinity norm are introduced to evaluate the impact of interactions on the transient response of the VSC. Finally, the DC gain of a certain set of transfer functions is used to assess the impact of control loops interactions on the set-point tracking capability of the VSC. The introduced indices along with time-domain simulations show that the transient response of the d-axis control loops is not impacted by the interactions, whereas that of the q-axis control loops is significantly impacted by the interactions. The set-point tracking capability is proved to be independent of interactions. [ABSTRACT FROM AUTHOR]

This paper analytically examines how the condition of weak grid connection affects the torsional sub-synchronous oscillations (SSOs) induced by a grid-connected DFIG in a power system. The examination focuses on the SSO mode of grid-connected DFIG, which is dominated by the phase locked loop (PLL) or DC voltage control. Theoretical analysis is carried out to prove that the condition of weak grid connection amplifies the impact of modal resonance between the DFIG and torsional dynamics of synchronous generators. The amplifying effect of weak grid connection exhibits as the decrease of damping of SSO mode of DFIG and increase of the associated residue when the grid connection weakens. Consequently, the DFIG is more likely to induce torsional SSOs under the condition of weak grid connection, leading to system instability in the worst case. Analytical examination presented in the paper reveals the mechanism about how the condition of weak grid connection plays a key role for the DFIG to induce the torsional SSOs. An example multi-machine power system with the grid-connected DFIG is presented. Results of modal analysis and non-linear simulation using detailed model of DFIG validate the analysis and conclusions made in the paper. [ABSTRACT FROM AUTHOR]

This paper presents the three-phase impulse overvoltage measured at the terminal of a 10 kV distribution line when the impulse current was injected into the phase conductor of the distribution line. The overvoltage observation station was installed at the terminal of the line to record the three-phase overvoltage waveforms. It is shown that the struck phase overvoltage consists of three components including the negative pulse, the stage of residual voltage maintenance and the overshoot oscillation part. The observed negative peak values of the struck phase overvoltage range from −85.4 kV to −96.0 kV in three different injected impulse levels at 90,120,150 kV charging voltage. The duration of residual voltage depends on the duration time of injected current. Furthermore, there is a strong positive relationship between the oscillation amplitude of the struck phase overvoltage and the injected current amplitude. The peak amplitudes of three-phase overvoltage always have the following magnitude relationship: struck phase C > induced phase B > induced phase A. The voltage coupling coefficients of induced phases will not exceed 0.4. The test method proposed in this paper will be helpful to the research on the lightning overvoltage response characteristics of the distribution line and the protection analysis of arresters. [ABSTRACT FROM AUTHOR]

Flexible Alternating Current Transmission Systems (FACTS) have achieved to enhance the flexibility of modern AC power systems, by providing fast, reliable and controllable solutions to steer the power flows and voltages in the network. The proliferation of High Voltage Direct Current (HVDC) transmission systems is leading to the opportunity of interconnecting several HVDC systems forming HVDC Supergrids. Such grids can eventually evolve to meshed systems which interconnect a number of different AC power systems and large scale offshore wind (or other renewable sources) power plants and clusters. While such heavily meshed systems can be considered futuristic and will not certainly happen in the near future, the sector is witnessing initial steps in this direction. In order to ensure the flexibility and controllability of meshed DC grids, the shunt connected AC-DC converters can be combined with additional simple and flexible DC-DC converters which can directly control current and power through the lines. The proposed DC-DC converters can provide a range of services to the HVDC grid, including power flow control capability, ancillary services for the HVDC grid or adjacent grids, stability improvement, oscillation damping, pole balancing and voltage control. The present paper presents relevant developments from industry and academia in the direction of the development of these converters, considering technical concepts, converter functionalities and possible integration with other existing systems. The paper explores a possible vision on the development of future meshed HVDC grids and discusses the role of the proposed converters in such grids. [ABSTRACT FROM AUTHOR]

The hybrid LCC/VSC cascaded HVDC (HC-HVDC) scheme, in which the LCC is adopted as rectifier, and one LCC in series with multiple paralleled VSC based MMCs is adopted as inverter, combines the advantages of both LCC and VSC-MMC technologies. Presently, a HC-HVDC project is planned to deliver the hydro power from Baihetan to Jiangsu in China. One of the major challenges is to suppress the DC overcurrent issue of VSC-MMCs especially under commutation failure condition of LCC at inverter side. Based on Baihetan-Jiangsu project under construction, the model of HC-HVDC system is developed in PSCAD/EMTDC. In the system, the rectifier employs a dual 12-pulse LCC, while the inverter adopts a hybrid scheme, i.e., one LCC converter in series with three paralleled VSC-MMC converters. This paper addresses the main cause and feature of the DC overcurrent, then proposes an overcurrent suppression control method for HC-HVDC system based on fuzzy clustering and identification approach. And the system transient performances with the proposed control approach are evaluated under AC fault conditions. The results show that the proposed approach can not only suppress the DC overcurrent following the commutation failure to a certain extent, but also improve the post-fault recovery performance of the overall system. [ABSTRACT FROM AUTHOR]

This paper analyzes the unsymmetrical operation of the dc/dc MMC caused by parametric uncertainty. The unsymmetrical operation is referred to as the condition in which parameters involved in ac power generation are not equal in the phase-legs of the converter. Because existing models in the literature cannot exhibit the unsymmetrical operation of the dc/dc MMC, new detailed and simplified steady-state models are developed in this paper. In the developed models, the connection between the operation of different phase-legs shows itself when the dc-link impedance is considered. Using the developed models, the parameters that can force the converter to operate in unsymmetrical conditions are identified, and the maximum variation that the converter can tolerate is found. It is shown that even a small parameter variation leads to the leakage of the ac circulating current into the dc-link, which is not acceptable. By conducting various case studies, the impacts of the dc-link length, the transmitted power, and the conversion ratio on the unsymmetrical operation of the dc/dc MMC are characterized. The results showed that the converter would be more sensitive to the parameter variation as these parameters increase. Comparative analysis and simulation results confirm the validity and effectiveness of the presented models and analysis method. [ABSTRACT FROM AUTHOR]

A modular multilevel converter control system, based on converter energy storage, is proposed in this paper for two different control modes: active power and dc voltage. The proposed control system decouples the submodule (SM) capacitor voltages from the dc bus voltage. One of the practical applications is the management of active redundant SMs. A practical HVDC system with 401-level MMCs, including 10% redundancy in MMC SMs, is used for validating and demonstrating the advantages of the proposed control system. This paper also presents a novel capacitor voltage balancing control based on \max–\min functions. It is used to drastically reduce the number of switchings for each SM and enhances computational efficiency. [ABSTRACT FROM AUTHOR]

This paper presents an evolution of control systems of Modular Multilevel Converters (MMCs) focusing on the internal voltages and currents dynamics. MMCs have passive components inside the converter that create extra dynamics compared to conventional VSCs. Some control schemes that do not consider these internal dynamics may still stabilize the system asymptotically thanks to the linearisation in the modulation step. However these control schemes are less robust because they are prone to poor damped oscillations on the dc side of the converter. The MMC circuit and energy relationships are presented in this paper. Along with a gradual development of the energy based control, the important roles of each internal dynamics are clearly demonstrated. Experimental results are presented to show the impacts of the linearisation in the modulation step on the system behaviour. [ABSTRACT FROM AUTHOR]

The short-circuit response of inverter-interfaced distributed generators (IIDGs) is not adequately represented in many conventional protection studies. This paper presents an in-depth analysis of IIDG behavior during grid faults and proposes a more accurate reduced-order parameterized short-circuit current (RPSC) model of inverters. Typical inverter components are thoroughly investigated to identify those that play dominant roles during faults. The paper shows that the current limiter is the dominant factor for the steady-state fault-current of inverter; while the inverter filter along with the severity of the voltage disturbance largely determine the initial transient spike of inverter fault current. The proposed model is low-order and can be used in large scale simulations. The parameters of the proposed RPSC model can be extracted from laboratory experiments without requiring proprietary manufacturer information. The proposed fault-current model is analogous to the well-known synchronous machine model that segregates the inverter fault current into subtransient, transient, and steady-state fault currents. Experimental and simulation tests are presented to validate the model. [ABSTRACT FROM AUTHOR]

Autonomous power systems with a single power station and a high-voltage (HV) network may be susceptible to overvoltage instability, especially during light-load conditions. Moreover, in low inertia systems, considerable frequency excursions may be observed after disturbances. To deal with voltage and frequency stability problems in such isolated power systems, several measures should be taken, such as rules for adequate automatic voltage control of the synchronous generators and load-tap-changers (LTCs), and/or adequate design of actions applied during emergency system conditions such as reactors switching, and redesigning underfrequency load shedding taking into account overvoltage problems. The effectiveness of the proposed countermeasures against overvoltage instability in autonomous power systems is illustrated in this paper. In 2016, the autonomous power system of the Greek island of Rhodes experienced similar voltage/frequency problems leading to a blackout. This event has been accurately reconstructed in this paper. The application of the suggested countermeasures during the simulation of the 2016 blackout event in Rhodes, further highlighted the effectiveness of these measures, providing a guideline for similar cases. [ABSTRACT FROM AUTHOR]

The presence of overvoltage can cause the insulation deterioration and excite the partial discharges (PD) in gas-insulated switchgear (GIS), and it is necessary to detect the overvoltage and PDs simultaneously to evaluate the insulation performance. A novel GIS internal composite sensor for PD detection and overvoltage measurement is proposed in this paper. The proposed sensor is mainly formed with a disc-type monopole UHF sensor and an overvoltage sensor. The effectiveness and sensitivity of the sensor are tested on a designed platform under power frequency voltage, switching impulse, lightning impulse, and oscillating lightning impulse, respectively. Experiment results show that the proposed sensor can be used to detect overvoltage and UHF signals effectively and is expected to help in the GIS condition evaluation. [ABSTRACT FROM AUTHOR]

Electrical equipment of the floating nuclear power plant operates in a long-term vibration environment. Ground faults occur frequently and are often accompanied by arc, a reliable arc suppression algorithm for the generator stator winding is necessary. In this paper, an active arc suppression method is proposed by connecting a controllable voltage source to the generator neutral point. Through regulating the neutral point voltage to be equal in amplitude and opposite in phase to the fault potential, the fault point voltage can be clamped to a low level to achieve arc suppression. Since the generator's phase potential contains certain harmonic components, the controllable voltage source includes fundamental and third-order harmonic components. To accurately calculate the output voltage, online calculation methods for the fault location, fault potential and grounding capacitance are proposed. The accuracy of the fault location method is verified by simulation and dynamic test. And simulation results based on PSCAD/EMTDC software show that the proposed method can achieve effective arc suppression at different ground fault conditions. [ABSTRACT FROM AUTHOR]

Multilevel converters (MLCs) are pioneers in the field of electrical energy conversion. From the classification of MLCs, modular multilevel converter (MMC) is top-rated due to its attractive structure and performance. The modular nature and no need for isolated DC resources are two significant advantages of this converter. However, the need for many sensors to control its performance is a considerable drawback. In addition, the internal circulating current in the MMC causes losses, decreases efficiency, and increases the voltage ripple of capacitors. This paper proposes combining a new capacitor voltage sorting method and an open-loop controller based on arms energy estimation to control the MMC using two voltage sensors in the arms and one current sensor at the output. The proposed method ensures continuous voltage balancing of the capacitors and removes multiple voltage sensors from sub-modules (SMs). The simulation and experimental results verify the accuracy and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In the conventional sliding mode control, the four-leg distribution static compensator (DSTATCOM) currents are controlled based on a current error in each phase. However, the four currents in a four-wire system can not be independently controlled variables and hence one of the four controllers is redundant in conventional schemes. Further, the current dynamics of a DSTATCOM converter are coupled through converter pole voltages in the natural reference frame. This leads to cross-coupling in the sliding variable equations with respect to four manipulated input variables. Considering the above points, in this paper, the current due to Thevenin’s equivalent load neutral-point voltage is considered as a fourth independent controlled variable and the corresponding system dynamic equations are presented. To get a decoupled feature, a new sliding surface function is structured. The performance of a DSTATCOM with the proposed control scheme under various operating conditions is validated through a detailed simulation study and experimental results, obtained from a laboratory prototype of four-leg DSTATCOM. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

Power flow (PF) flexibility in the multi-terminal HVDC (MT-HVDC) grids is a thought-provoking issue. It leads to employing the active DC power flow controller (DC-PFC)s. Hence, this paper examines the static average model (AM) and power injection model (PIM) of an interline DC-PFC (IDC-PFC). It is to provide a suitable base for DC PF studies and easy embedding of the DC-PFCs into MT-HVDC grids’ PF equations. In this regard, this paper proposes a new DC PF solver (DC-PFS) for the IDC-PFC compensated MT-HVDC grids within the well-accepted Newton-Raphson (NR) framework. It requires a few modifications in the main structure of the system's Jacobin (J) matrix compared to the uncompensated MT-HVDC grid. Also, the system's admittance matrix and its symmetry are preserved. In the proposed concept, the IDC-PFC cooperates with other MT-HVDC grid's state variables to satisfy the predetermined control objective(s). Furthermore, this paper proposes a new solution procedure (SP) to handle various system's limitations during the processes of solving the DC PF problem. Meanwhile, there is no need to modify the related J matrix. The effective and accurate performance of the IDC-PFC's models, as well as presented NR-based DC-PFS and SP, are verified by performing several simulations on the 8-bus CIGRE MT-HVDC grid. [ABSTRACT FROM AUTHOR]

The development of a revolutionary design for transmission lines was recently introduced by shifting phase configurations and sub-conductors into “unconventional” arrangements that were geometrically optimized to maximize natural power. The objective of this paper is to study the electromagnetic transients that result from the simultaneous and sequential line energization and re-energization of the previously developed unconventional high surge impedance loading (HSIL) lines. Statistical switching overvoltage (SSOV) studies are performed using a frequency domain method based on the inverse numerical Laplace transform. Compared to a conventional line, all unconventional HSIL line designs studied in this paper lead to very similar surges for long line lengths (400 km) and similar values for short line lengths (100 km), indicating additional advantages of these lines. The use of a frequency domain method for SSOV studies offers enhanced accuracy, simulation flexibility, and substantially lower computational burden compared with traditional time-domain methods. [ABSTRACT FROM AUTHOR]

Geomagnetic Disturbance (GMD) impacts a power system by causing the circulation of quasi-dc Geomagnetically-induced Currents (GICs) in transmission lines and high-voltage transformer windings leading to transformer saturation, increased reactive power losses, and voltage regulation problems. Utility planners use various analysis methods and simulation tools to analyze GMD system impacts. These techniques can be broadly categorized into load-flow-based (LF), transient stability type (TS), and electromagnetic transient type (EMT) methods. These methods are based on different modeling assumptions and solution techniques. There is a need for evaluation of these assumptions and cross-examination of results to ensure their accuracy. Such an evaluation is essential to ensure that planners performing required GMD vulnerability assessments have confidence in the results. This paper evaluates the LF, TS, and EMT methods through cross-examination of their results. The objective is to identify their limitations, assess the consistency of their results, and provide assumptions on their use for analysis of GMD system impacts. The study is conducted in consistence with the North American Electric Reliability Corporation (NERC) GMD guidelines and standards. [ABSTRACT FROM AUTHOR]

This paper presents a small-signal dynamic model for a modular multilevel converter (MMC) based HVDC grid, and then systematically i) identifies the system dominant oscillatory modes, ii) quantifies their propensity to instability phenomena, and iii) devises appropriate countermeasures. Based on the developed model, the eigen structure of an HVDC grid is characterized and the impact of the system parameters, configuration, AC system strength and operating point on the damping ratios of the oscillatory modes, and consequently the HVDC grid stability, are investigated. The model is also applied to systematically determine the sensitive parameters and optimize them to mitigate oscillatory modes and prevent instability. The eigen analysis results are verified based on time-domain simulation studies in the PSCAD/EMTDC platform. [ABSTRACT FROM AUTHOR]

With the emergence of the hybrid multi-infeed high voltage direct current (HMIDC) system, there is complex dynamic interaction between the AC/DC system and converter stations, while the interaction mechanism of the HMIDC system is unclear. For this purpose, this paper establishes the HMIDC linearized model based on the motion equation concept. Then, after decoupling and reconstructing the interaction path of the HMIDC system, the damping coefficients are derived. The AC system strength and voltage source converter (VSC) terminal voltage controller parameters are selected to analyze the impacts on damping coefficients, and the interaction mechanism of the HMIDC system is analyzed. In order to solve the potential instability issue, an additional damping controller in the VSC terminal voltage loop is proposed to enhance the voltage stability of HMIDC system, which is realized by adjusting the reactive power/amplitude coupling damping coefficient. Finally, the RT-LAB-based hardware-in-the-loop experiments verify the accuracy of the interaction mechanism analysis of the HMIDC system and the effectiveness of the proposed controller. [ABSTRACT FROM AUTHOR]

In DC distribution networks, the uncertainties of renewable energies and loads cause frequent voltage fluctuations. In this paper, a voltage regulation strategy based on the combined coordination of centralized optimal control (COC) and adaptive droop control (ADC) is proposed for droop-controlled DC distribution networks. In the COC strategy, the operation reference power of voltage source converters (VSCs) is optimized using the bus injection power measurements to improve the voltage profile and balance the power loading rates of different VSCs. The VSC capacity margin constraint is established to ensure that the capacity margin of each VSC is sufficient to cope with the unexpected fluctuation of loads and renewable energies. Then, an ADC strategy is adopted to handle voltage fluctuation between adjacent two COCs. In the ADC strategy, the operation reference power of the VSCs is further adjusted to recover the voltages. The voltage regulation is achieved based on the relationship among the VSC voltages and the minimum/maximum voltages of the whole network, which does not depend on the information of each nodal voltage and thus real-time network communication is avoided. The simulation results show that the proposed voltage regulation strategies can effectively improve the voltage profile under various uncertain environments. [ABSTRACT FROM AUTHOR]

Fault response of an inverter based resource (IBR) is dictated by its control scheme, making it markedly different from the response of a synchronous source. This has led to misoperation of distance relays when fed by IBRs. Published literature is mostly focused on changing the control design of inverters, but this approach is not practical, as these controls are proprietary and beyond the reach of utilities. To resolve this issue, this paper proposes a method for a source-agnostic distance relay that works in time-domain. Using only single ended measurements, the relay detects, classifies and locates any fault on the line it monitors. The method does not require any polarization technique. It is shown to work for unbalanced lines of any length, for transmission or distribution system with any number (even 100%) of IBRs, is immune to load encroachment, decaying dc offset and prefault currents. With very limited communication, it is also shown to be immune to fault resistance. [ABSTRACT FROM AUTHOR]

The stability problem of low-voltage multi-terminal DC (MTDC) systems has drawn much interest. This paper focuses on the oscillation instability phenomenon of low-voltage MTDC systems and analyzes the interaction behavior between each voltage-source converter and the DC network oscillation mode. The typical structure and control strategy of a low-voltage MTDC system under master-slave control is first described, and its equivalent circuit is established. Then, an interaction behavior analytical model is proposed, and the source-network and network-load interaction characteristics are studied. Furthermore, a system stability analysis method is built based on the modularized modeling, which can solve the problem of how to address the complexity of high-order low-voltage MTDC systems. The transfer function of the whole system is conveniently established, revealing the system instability mechanism. The proposed method can provide effective stability assessment for low-voltage MTDC systems. Finally, the results are verified using electromagnetic transient simulation and experimentally validated using a low-voltage three-terminal DC system test platform with AC 0.4 kV/DC 800 V. This research can be flexibly extended to high-order systems for controller design and performance optimization. [ABSTRACT FROM AUTHOR]

This paper reports the waveform characteristics and parameters of the overvoltage at the terminal of a 1.5 km 10 kV distribution line by direct triggered lightning. The three-phase overvoltage exhibited three kinds of waveforms, all including the initial rising process of the negative peak, the transition from negative peak to the positive peak or the residual voltage, and the subsequent oscillation process. It is observed that the negative peak value of the three-phase overvoltage is between −8.2 kV and −96.1 kV and the rise time of negative peak is between 3.2 μs and 31.7 μs, while the corresponding peak value of the return stroke current is between 3.3 kA and 32.9 kA. When the return stroke current is relatively small, the negative peak value of the direct struck phase overvoltage is twice or more than that of the indirect struck phase. When it is larger, the negative peak value of the indirect struck phase overvoltage is much closer to that of direct struck phase. There is good linear relation between the negative peak value of the indirect struck phase overvoltage and the peak value of the lightning return stroke current, with correlation coefficient being 0.98 and 0.90. [ABSTRACT FROM AUTHOR]

In this paper, we propose an idea to integrate more renewable energy into the existing China power grid and to provide remote islands with a reliable power supply. The idea is to expand the existing point-to-point line-commutated converter (LCC) HVDC transmission link into a hybrid multiterminal HVDC (hybrid MTDC) system, which contains LCC stations and voltage-source converter (VSC) stations. Accordingly, this paper proposes a novel control strategy for this system called active voltage feedback control, which does not need any high-speed communication system under various disturbances, such as wind speed variations, load fluctuations, faults, etc. This paper also adds secondary frequency regulation to the synchronverter, which is one way of combining the VSC converter with synchronous machine behavior. Then, this paper applies an approach to limit its current under fault conditions. Finally, the entire hybrid MTDC system is modeled in PSCAD/EMTDC. Simulation results show that the improved synchronverter is able to achieve secondary frequency control, and the presented active voltage feedback control works very well when exposed to various disturbances. [ABSTRACT FROM AUTHOR]

The use of VSC-HVDC grids for offshore wind farm integration will require the use of dc breaker systems and presently they require dc reactors to limit the rate of rise of fault current. The introduction of large dc reactors throughout a VSC-HVDC system can have a significant impact on its stable operation and will require additional control. This paper analyzes this problem and proposes a PSS-like control (DCPSS) to aid dc grid stability and cope with this effect. A generalized analytical model for studies on dc voltage control is presented. Key stability and transient performance issues caused by the use of the dc reactors in a multiterminal system are investigated by analyzing poles, zeros, and frequency responses of open-loop and closed-loop models. Design and location identification methods for the DCPSS are provided. An excellent damping enhancement is achieved by this controller. The analytical studies and time-domain simulations in this paper are performed based on two VSC-HVDC models. [ABSTRACT FROM AUTHOR]

This paper investigates the Multilevel Current Source Converter (MCSC) STATCOM. It proposes a new method of modulation. The new modulation method produces less THD and di/dt at the terminals of the MCSC STATCOM when compared to the widely used Phase-Shifted Carrier SPWM (PSC-SPWM). To ensure the inductors' currents remain balanced, a Current Balancing Algorithm (CBA) is presented. The CBA does not require any controls. It relies on assigning optimum switching states to each CSC module in real-time. In addition, two control strategies are presented in this paper. The first one assumes the STATCOM to be a SISO. Therefore, it only requires one PI controller. However, the gains for the controller must be changed if the STATCOM was to transition from capacitive mode to inductive mode, or vice versa. The second control strategy overcomes this problem by implementing a TITO integral state feedback controller. The contributions of this paper are validated via simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive model of modular multilevel converter (MMC) for electromagnetic transient (EMT) simulations. The model is applicable to MMCs with arbitrary numbers of half-bridge and full-bridge submodules. The proposed design includes average value model, arm equivalent model, and detailed equivalent model. It allows smoothly transitioning from one model to another during time-domain simulations depending on the desired accuracy and execution time constraints. Modifications required in conventional MMC models to achieve smooth transitions are presented in the paper. Time-domain initialization methods are developed for each constituting model, including initialization of the appropriate control system blocks. Validity and effectiveness of the proposed adaptive model is demonstrated using EMT simulations of 401-level MMC-HVDC system. [ABSTRACT FROM AUTHOR]

The advancements in smart grid technologies had brought forth the prospect of self-healing distribution grid through intentional islanding, aided by the steadily rising penetration of inverter-based distributed generations (IBDGs). Adaptive protection is the key enabler for this resilient grid architecture. For cost-effectiveness, overcurrent relays (OCRs) with adaptive features had been proposed, often with the sensitivity problem due to low short-circuit current magnitude from the IBDG taken into consideration and largely addressed. However, apart from this widely discussed sensitivity problem, there is an underlying issue on selectivity of the OCR which is frequently disregarded when designing an adaptive overcurrent protection scheme for IBDG dominated microgrid. This selectivity problem is mainly caused by the current diversion to load during fault, which is often disregarded when performing OCR grading for a conventional grid. In this paper, this selectivity problem of the OCR is discussed in depth through a comparative study of conventional grid and a modern IBDG dominated grid. The coordination time interval margin violations problems are demonstrated through theoretical calculations and real-time hardware-in-the-loop experiments. This research aims to provide better insights into the selectivity problem as a step towards achieving a cost-effective yet reliable overcurrent-based adaptive protection for IBDG dominated microgrid. [ABSTRACT FROM AUTHOR]

This paper presents a new voltage support (VS) strategy for photovoltaic (PV) systems based on voltage sensitivity analysis to enhance the dynamic voltage stability (DVS) of islanded microgrids (MGs). Every network contains different characteristics. In particular, MGs have unique features compared to utility grids such as high resistance to reactance ratio (R/X). Consequently, injection of both active and reactive current is likely to improve the DVS of the islanded MG. Therefore, instead of engaging the entire capacity to reactive current injection which is performed in conventional voltage support strategy, both the active and reactive current is injected in the proposed strategy. On contrary, without considering the fact that each network contains distinctive characteristics, other strategies with both active and reactive current injection provide fixed active and reactive current which are uniform for all networks. To convey the network distinctive features on VS strategy, voltage sensitivity subject to active and reactive current injection is used in the proposed strategy. As a consequence, unlike other fixed active and reactive current strategies, the proposed strategy provides unique combination of active and reactive current for every network. The concept and derivation of the proposed strategy is clearly described. Network sensitivity analysis is carried out to determine the voltage sensitivity coefficients. The effectiveness of the proposed strategy is theoretically demonstrated and also compared with other strategies. Case studies are carried out on two different islanded MGs. The results show that the proposed voltage support strategy is capable of enhancing the DVS of islanded MGs by mitigating a possible instability, and by restoring the voltage faster than other strategies. [ABSTRACT FROM AUTHOR]

To improve the reliability of power supply, reclosing schemes are required after transient faults, which commonly occur in overhead line based high voltage DC (HVDC) systems. However, in the event of permanent faults, the auto-reclosing scheme may cause a severe strike. To avoid the severe impacts caused by permanent faults, the fault type should be discriminated before activating the reclosing scheme. Therefore, an adaptive reclosing scheme based on phase characteristics is proposed in this paper. Firstly, the modulation of a periodic voltage by actively controlling the hybrid DC circuit breaker (DCCB) is introduced. Then, a cascaded π equivalent model and its decoupling algorithm are presented to analyze the frequency-domain characteristics of the measured impedance of the coupled overhead lines. From the frequency-domain characteristics, the frequency of the periodic detecting voltage is determined to analyze the phase features of the measured impedance at primary frequency. The permanent or transient faults can thus be accurately identified by using these different phase characteristics, with negligible influence on the healthy lines. In addition, the proposed scheme is robust to various fault resistances, leading to improved reliability. The effectiveness of the proposed scheme is verified in PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

With the increasing number of controllable devices in the grid, devices owned by different entities are supposed to cooperatively support the grid operation. To balance the various interests of the customers and the utility, this paper proposes a two-level scheduling algorithm to address voltage regulation by coordinating the customer-owned battery energy storage system (BESS) and utility-owned load tap changers (LTCs) in power distribution systems. The objective is to find the optimal operation scheduling for both BESSs and LTCs that simultaneously maximize the economic payback and satisfy system operation rules. For BESSs, a local optimization problem is formulated in a chance-constrained manner in major consideration of the economic performance. For the utility interest, a Markov decision process (MDP) and a computationally efficient reinforcement learning (RL) algorithm are utilized to solve the optimal tap setting problem. To coordinate BESSs and LTCs, a global voltage adjustment is applied. The effectiveness of the proposed algorithm is validated via simulations on the IEEE 13-node and 34-node distribution test feeders. [ABSTRACT FROM AUTHOR]

This paper presents a novel phase-tracking robust-synchronization-loop (RSL) to track the phase and frequency of the grid voltage. A detailed analytical model of the proposed RSL algorithm is presented. Further, a state-space small-signal model is developed, including the dynamics of a grid-connected converter and its controller. From the small-signal analysis, it is shown that the eigenvalues associated with the states of the RSL remain in the left half-plane even for a very weak grid condition with a grid impedance of 1.0 pu, thus, it provides better stability property with the grid-connected converters. In order to show the effectiveness of the proposed RSL, simulation results are provided for different scenarios of the grid conditions such as voltage and frequency disturbance, unbalance grid condition and grid faults. Further, the performance of the RSL algorithm is tested by experiment in lab. The results show that the proposed method effectively tracks the phase and frequency of the grid voltage and maintains the good synchronism of the converters during different disturbances. [ABSTRACT FROM AUTHOR]

The paper addresses a real-time optimization-based reference calculation integrated with a control structure for Modular Multilevel Converters (MMC) operating under normal and constrained situations (where it has reached current and/or voltage limitations, as it may occur during system faults). Firstly, a nonlinear optimization problem has been developed in which it prioritizes to satisfy the AC grid current set-points imposed by the transmission System Operator (TSO). The constrained nonlinear optimization problem is formulated based on the steady-state model of the MMC, whereby the prioritization is achieved through distinct weights defined in the Objective Function’s (OF) terms. The resultant optimization problem, however, is highly nonlinear requiring high computation burden to be solved in real-time. To cope with this issue, this paper applies a Linear Time-Varying (LTV) approximation, which permits to represent the nonlinear dynamics of the system as constant parameters, while a Linear Time-Invariant (LTI) system is used to formulate the optimization constraints. The converter’s current references are determined in real-time by solving a constrained linearized optimization problem at each control time step, which considers the TSO’s demands, the current MMC operating point and its physical limitations. Theoretical analyses comparing the responses of the linear and nonlinear optimization problems are performed to validate the accuracy of the LTV approximation. Finally, the linearized-optimization problem is integrated with the MMC controllers, evaluated under different AC and DC network conditions and compared with conventional control strategies, where it is shown that the presented method can be potentially employed to obtain the MMC current references for distinct network scenarios. [ABSTRACT FROM AUTHOR]

The current-limiting inductors (CLIs) are commonly used to suppress DC fault current to safely trip DC circuit breakers in MMC-HVDC systems, but it significantly jeopardizes DC dynamics and causes instantaneous power mismatch between AC and DC sides of islanded rectifier station (RS), exposing MMC internal states to large disturbance. This paper firstly provides a detailed analysis of the influence of CLIs on AC fault, establishes RS mathematical representation including AC side dynamic, and reveals the mechanism of DC voltage oscillation, modulation saturation and PCC waveform distortion. The analysis shows that the AC and DC fault characteristics are decoupled under unsaturated AC modulation, but coupled under excessively low submodule capacitor voltage, where AC modulation is saturated and PCC waveforms are distorted. To solve this issue, a novel RS AC fault ride through method for MMC-HVDC system with CLIs is proposed to stabilize RS DC voltage, desaturate AC modulation and decouple fault characteristics by regulating the zero-sequence modulation of circulating current suppression. In addition, a current reference disturbance and an AC energy dissipation device coordinated control are designed, which adaptively recovers the submodule capacitor voltage. Finally, the feasibility of the proposed method is verified by simulation results. [ABSTRACT FROM AUTHOR]

The real-time estimation of the AC power system equivalent parameters enables the grid-connected Voltage Source Converter (VSC) to achieve more effective stability control during a short-circuit fault. In this paper, a novel Thevenin Equivalent (TE) parameter estimation method based on local synchronous Phasor Measurement Units (PMUs) is proposed and applied to the Phase-Locked Loop (PLL) synchronization stability control of VSC. First, the relationship between the variation of the measured voltage and the error of the estimated impedance is strictly derived based on the rules of norm inequality. Then, according to the analysis of the upper bound of the system voltage change, a voltage threshold is proposed to select the PMU measurements to ensure the accuracy of the estimation during the large disturbance. Finally, using the estimated TE parameters, the current control instruction of VSC during the fault is calculated in real-time to ensure a synchronous and stable operation. The simulations reveal that the proposed estimation method can accurately track the TE parameters after a fault. Furthermore, the associated current control actions during a fault can ensure the PLL synchronization stability of VSC. [ABSTRACT FROM AUTHOR]

This paper proposes a novel reactive power-based control strategy for single-phase PV inverters (PVIs) to simultaneously improve voltage unbalance (VU) and voltage regulation (VR) in low-voltage distribution networks. The proposed strategy relies on communication links between neighboring PVIs to exchange limited data. In this strategy, each PVI finds communication paths between itself and the closest neighboring ones connected to other phases. Then, using the obtained paths and the maximum and the minimum voltage magnitude of the grid, PVIs improve both VU and VR at the same time. The performance of the proposed control strategy is evaluated by various simulation studies using the IEEE European low-voltage test feeder and considering different operational conditions. In addition, the impacts of moving clouds and a failure in the communication links have been assessed. The simulation results exhibit that using the proposed control strategy, the voltage magnitude of all the nodes will remain within the allowed limits and at the same time, the phase voltage unbalance factor will be also significantly improved. [ABSTRACT FROM AUTHOR]

Optimal protection coordination is usually solved for the original network topology with all lines, loads, and generation intact. However, power grids may experience contingencies due to transient events, e.g., generation or line outages. Low fault currents of inverter-interfaced distributed generators (IIDGs) necessitate a sensitive and reliable protection scheme. This paper proposes a protection scheme for islanded microgrids powered by droop-based IIDGs. The protection scheme utilizes virtual impedance-fault current limiters to limit IIDGs fault currents and achieve protection coordination. A two-stage method for optimal protection coordination (OPC) of directional overcurrent relays (DOCRs) is devised. In Stage I, relays short-circuit currents are calculated. Then, constraints on the operation times of primary and backup DOCRs are formulated for the islanded topology and each possible topology following an N-1 contingency. Lastly, in Stage II, the OPC problem is formulated as a constrained nonlinear programming problem and solved to obtain the optimal DOCRs settings. A radial test microgrid that is part of a Canadian urban distribution system is used to ensure the success of the proposed OPC method. [ABSTRACT FROM AUTHOR]

In this paper, a reliable methodology is proposed in order to implement and validate a Model Predictive Control (MPC) scheme on an actual Voltage Source Converter (VSC) integrated in a scale-down multi-terminal DC grid. The objective of the investigated MPC controller is to enable AC frequency support among two asynchronous AC areas through a High Voltage Direct Current (HVDC) grid, while considering physical constraints, such as maximum and minimum DC voltage. A systematic and accurate implementation strategy is proposed, based mainly on the Hardware In the Loop (HIL) and Power Hardware In the Loop (PHIL), leading to the real-life testing on VSC, controlled by a classical microcontroller. The technical problems during the implementation process, as well as the proposed solutions, are described in detail through this paper. This procedure is deemed valuable to bridge the gap between offline simulation and the actual implementation of such advanced control scheme on experimental test rig. [ABSTRACT FROM AUTHOR]

The effect of reduction in the terminal voltage of a grid-tied inverter together with minimization in total harmonic distortion (THD) of terminal voltage and current, in the presence of dead-band in the switching remains always challenging for the researchers. With high switching frequency, this issue increases by many folds. The grid-tied inverter used for harmonic compensation acts as a shunt active power filter (SAPF). The implementation of the dead-band elimination technique is based on output current polarity detection, suffers from multiple zero-crossing due to the generation of high frequency switching harmonics during SAPF operation. This paper deals with a dead band elimination methodology together with harmonic compensation using SAPF under non-linear and unbalanced loading conditions. Here, SAPF uses a dual fundamental component extraction (DFCE) scheme with modified complex coefficient filter (MCCF) to extract fundamental components for reference current generation to implement an indirect current control PWM scheme. MCCF extracts fundamental components even in the presence of dc offset and unbalancing at the input. For incorporating dead-band elimination in control, exact polarity detection is done separately through SAPF output current estimation using sensed load current, and modified CCF computed reference source current. Since the estimated SAPF output current contains no high-frequency switching harmonics, the dead-band elimination technique can be correctly implemented. To synchronize the zero-crossing of the estimated and actual SAPF current, an adaptive delay control is used. The proposed MCCF based control logic’s performance together with the dead-band elimination technique is validated for SAPF operating under non-linear, unbalance, and dynamic load conditions. The proposed dead-band elimination scheme based SAPF model is developed and simulated using MATLAB/ SIMULINK. The simulation results show a significant reduction in source current harmonics due to the elimination of odd harmonic injection into the system by incorporating dead-band elimination in SAPF operation. The real-time simulation of the proposed method is also validated using OPAL-RT OP4510 real-time platform. [ABSTRACT FROM AUTHOR]

Behind-the-meter battery energy storage is used to mitigate non-dispatchability of customer-owned renewable sources. While serving their owners’ objectives, their underutilized capacities can be used to provide grid services to justify their cost. However, the integration of these resources extends the size and complexity of the network operation problem, imposing a processing burden on the central control system. In this paper, an agent-based distributed control framework is proposed that enables utilizing of the underutilized behind-the-meter capacities. In this framework, while the prosumer agents initially schedule their resources for daily cost management, a local customer aggregator agent performs day-ahead active and reactive power control on the underutilized behind-the-meter batteries to provide multiple grid services. A novel grouping algorithm is developed based on voltage sensitivity and a modified $k$ -means clustering method to assign customer groups to the local agents and establish the network subsystems. Mixed-integer linear programming is used to model and solve multiple optimization problems. The proposed framework is applied to the 123-bus distribution network. The simulation results show its effectiveness in terms of complexity and optimality, compared to the central control approach in allocating the unused behind-the-meter resources for two common industry needs: network bottleneck congestion relief and grid-edge voltage support. [ABSTRACT FROM AUTHOR]

This paper proposes a novel hybrid AC/DC microgrid architecture incorporating a central energy storage system (ESS) for both the AC and the DC sub-grids. To ensure effective operation of the proposed hybrid AC/DC microgrid architecture, a coordinated control strategy between the central ESS and the inter-linking converter (ILC) is proposed in the paper. The proposed central ESS provides voltage and frequency control to the AC sub-grid by measuring voltage and frequency at the point of common coupling (PCC) of the AC sub-grid, while providing DC voltage support to the DC sub-grid by measuring DC sub-grid’s PCC voltage. Furthermore, per-unit frequency and the DC sub-grid PCC voltage are utilized to transfer power between the two sub-grids via the ILC. Therefore, two control strategies are coordinating with each other and maintain stable operation. The central ESS eliminates the use of multiple ILCs and complex control schemes for charge and discharge control to maintain same state of charge levels at each ESS. Effectiveness of the proposed coordinated controller is verified by applying various load disturbances, faults, and under different modes of operation. [ABSTRACT FROM AUTHOR]

The neutral grounding method is one of the crucial technologies used to ensure the safe and stable operation of distribution networks. With the development of power electronics-based devices, the application of highly controllable inverters to grounding systems has become a new research direction. In this review paper, based on the summary and analysis for the research status, the flexible grounding system is systematically classified according to its control strategy and structure. And then, the following core technologies are summarized: faulted line selection, current component detection, high-resistance ground identification, ground parameter measurement, neutral point voltage control, and fault location. Subsequently, deficiencies of flexible grounding systems are summarized from the following four perspectives: reliability, accuracy, speed, and stability. Finally, some discussions and recommendations for future development and research direction are presented. Especially, the reliability-enhanced hybrid grounding system that combines active inverters and low resistance for high-resistance ground faults is recommended. This paper provides a systematic literature review of the crucial technologies for flexible grounding systems and can be used as a technical reference for future research. [ABSTRACT FROM AUTHOR]

The paper addresses an improved inner current reference calculation to be employed in the control of modular multilevel converters operating during either balanced or unbalanced conditions. The suggested reference calculation is derived based on the AC and DC additive and differential voltage components applied to the upper and lower arms of the converter. In addition, the impacts caused not only by the AC network’s impedances but also by the MMC’s arm impedances are also considered during the derivation of the AC additive current reference expressions. Another issue discussed in this article regards that singular voltage conditions, where the positive-sequence component is equal to the negative one, may occur not only in the AC network but also internally (within the converter’s applied voltages). Several different inner current reference calculation methods are compared and their applicability during the former fault conditions is analyzed. The paper presents a detailed formulation of the inner current reference calculation and applies it to different unbalanced AC grid faults where it is shown that the presented approach can be potentially used to maintain the internal energy of the converter balanced during normal and fault conditions. [ABSTRACT FROM AUTHOR]

Accurate faulty phase detection under single-line-to-ground (SLG) fault is the basis of the emerging voltage-based fault arc suppression technology. Most conventional faulty phase recognition criteria assume the distributed line-to-ground parameters are symmetrical, therefore suffering invalidity in actual distribution networks especially under high-resistance ground-fault conditions. This paper firstly analyzes the magnitude and phase angle variation models of the phase-to-ground voltages before and after the SLG fault. Considering the asymmetrical distributed parameters and the line impedance, the specific phase-to-ground voltage variation rules corresponding to SLG fault on each phase are then discussed. Based on the voltage variation rules, a robust and practical method for faulty phase identification is proposed, which does not need the distributed parameters. Finally, the correctness of the variation rules and the availability of the proposed method is verified by simulation. Comparative study shows the proposed method has better accuracy and applicability with the conventional methods when the asymmetry and ground-fault resistance are high. [ABSTRACT FROM AUTHOR]

This paper introduces an averaging control strategy of the phase-unit losses of modular multilevel converters (MMCs). The quantitative analysis of the MMC phase-unit loss distribution under unbalanced ac conditions is carried out by investigating the individual component of the MMC arm currents. It shows that the unbalanced arm currents will result in unbalanced phase-unit losses. To address this issue, this paper proposes a predictive closed-loop-control-based zero-sequence voltage injection method that results in much averaged loss distribution under unbalanced ac conditions. The essence of the new method is that it adjusts the three-phase sinusoidal references so that the unbalanced arm currents are fully utilized to average phase-unit losses. This paper shows the effectiveness of the new approach by electromagnetic transient simulations on PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

A parallel hybrid modular multilevel converter (PHMMC) belongs to the class of modular multilevel converters, which have become potential candidates for high-voltage direct-current (HVDC) transmission systems. Due to the circuit topology of a PHMMC, the dc bus voltage contains low-order harmonics and cannot be fully regulated at a constant dc voltage. The dc bus voltage, if not properly controlled, leads to improper power transfer and increases the magnitude of dc current ripple on the dc transmission line. This paper proposes a zero-sequence voltage injection (ZSVI)-based model predictive control (MPC) strategy to control the dc current/power flow and simultaneously minimize the dc current ripple. The proposed strategy takes advantage of a cost function minimization technique to determine and inject the optimal zero-sequence voltage components into the dc- bus voltage of a PHMMC system. This paper derives a discrete-time dynamic model of the dc transmission-line current and, correspondingly, develops a predictive model. The predictive model is used to inject the appropriate amount of zero-sequence voltage components to the dc bus reference voltage waveform. Compared with the existing triplen harmonics injection method, the proposed ZSVI-MPC strategy improves the performance of a PHMMC system in terms of minimization of the dc current/voltage ripple. Performance of the proposed strategy for a 21-level PHMMC-based HVDC station system is evaluated based on time-domain simulation studies in the PSCAD/EMTDC software environment. The reported results demonstrate superior performance of the PHMMC-HVDC station operating based on the proposed ZSVI-MPC strategy, under various operating conditions, as opposed to the existing triplen harmonics injection method. [ABSTRACT FROM AUTHOR]