Search

This paper proposes a new modulated model predictive control method for the control of modular multilevel converters (MMCs) in voltage source converter-high voltage dc systems. The proposed method retains the advantages of the conventional finite control set-model predictive control methods by programing the nonlinear properties of the MMC into the design calculations while minimizing the ac line and circulating current ripples and steady-state error by generating modulated switching signals with a fixed switching frequency. In this paper, first, the predictive modeling of the MMC is provided. Next, the proposed control method is described. Then, the application of the proposed method to an MMC system is detailed. Finally, experimental results from an MMC system connected to a three-phase grid are provided to validate the theoretical outcomes. [ABSTRACT FROM AUTHOR]

The standard alternative-arm converters (AAC) with the sweet spot or short overlap operation have faced a challenge of balancing submodule (SM) capacitor voltages, where this issue has not been paid much attention so far. In this paper, a new control strategy for the SM-capacitor voltage balancing of the AAC applied in high-voltage dc transmission systems is proposed. The suggested control technique is composed of three regulators, where a control for the average voltage of all SM capacitors, the voltage balancing among the converter arms, and the voltage balancing of the individual SM capacitor are performed. Based on the operation principle of the standard AAC, which activates only three of six converter arms simultaneously, the energy balancing of the three activated arms is performed every one sixth of the fundamental cycle by the converter common offset voltage. Band-stop filters with the central frequencies at the fundamental, second-, and third-order components of the line frequency are applied to obtain the average values of the SM capacitor voltages for the feedback controllers. The simple proportional and integral controllers are employed for this scheme and the voltages of SM capacitors are mostly balanced during the steady states and kept closely to the rating with overshoot of less than 7% under the transient conditions. The proposed control method is verified by simulation results for a 33-level AAC under both normal and fault conditions. [ABSTRACT FROM AUTHOR]

Due to the demand for high reliability, modular multilevel converters (MMCs) are designed with redundant submodules. Redundant submodules can be integrated into the converter by employing different redundancy schemes: the conventional active scheme, the load-sharing active scheme, and the passive scheme. Different schemes have different impacts on the improvement of converter reliability. The contributions of this paper include that an analytical method is proposed to evaluate the reliability of MMCs under different redundancy schemes and the factors’ influence on the converter reliability is analyzed to determine the proper redundancy scheme. Reliability models of MMCs under different redundancy schemes are built using Markov chains and the iteration method. Based on the proposed models, the effects of redundant schemes are evaluated in terms of the converter reliability. A case study is conducted to validate the feasibility and robustness of proposed models and to specify the conditions in the favor of each redundancy scheme. The benefits of sharing redundancy among arms are also explored from the reliability point of view. If insulated-gate bipolar transistors (IGBTs) and capacitors are dominant components in a submodule in terms of failure rates, the load-sharing active scheme performs better; otherwise, setting the redundant submodules in an idle state is more effective. It is also found that the number of required redundant submodules is greatly reduced by sharing redundancy among arms. [ABSTRACT FROM AUTHOR]

This paper presents a new multilevel cascaded-type dynamic voltage restorer (MCDVR) with a fault current-limiting function. This topology can operate in two operational modes: 1) a compensation mode for voltage fluctuations and unbalances and 2) short-circuit current-limiting mode. The current-limiting function of the MCDVR is performed by activating antiparallel thyristors during the short-circuit fault, and deactivating them during normal operation. The mathematical model of the MCDVR system is also established in this paper. The control scheme design and optimal parameter selection are outlined based on the detailed theoretical analysis of the converter. The transient states of the MCDVR in the compensation mode and current-limiting mode are also analyzed. Simulation results based on the PSCAD/EMTDC software, and experimental results on a laboratory setup help to validate the proposed topology and the theoretical analysis. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become one of the most promising topologies for high-voltage dc–ac conversion. DC-side fault blocking capability of the MMC has prompted significant research in recent years. In this paper, a new switched capacitor submodule (SCSM) for MMCs is proposed which provides operation with DC fault blocking capability. In addition, successful voltage balancing is achieved with half the number of voltage sensors used with existing MMC cells. Generally, conventional sensor-based balancing techniques require a significant amount of measurements, 2m(N-1) voltage sensors, and 2m current sensors for an N-level m-phase MMC. The proposed cell will thus aid in reducing the complexity of the control system. A detailed illustration of the operational concept of the proposed architecture is presented in this paper. A comparison between the proposed SCSM and other existing MMC cells has been included to highlight the benefits of the proposed SCSM. A simulation model for an MMC-based HVDC system along with the proposed cell has been built to test its performance during normal as well as abnormal operating conditions. The simulation results show the effectiveness of the proposed architecture. [ABSTRACT FROM PUBLISHER]

This paper investigates the applicability of averaged-value models (AVMs) for modular multilevel converters (MMCs) operating in a voltage-sourced converter-based-high-voltage dc (VSC-HVDC) grid. The AVM models are benchmarked by comparison with a detailed electromagnetic transient model of the grid, including a fully detailed MMC model. Analysis results show that the AVM is only effective as long as the capacitors are large enough to maintain nearly constant voltage across each MMC submodule. This paper also shows that previously developed MMC averaged models are not able to accurately simulate the transients under dc fault conditions. This paper introduces topology changes to a previously proposed averaged model that results in much improved simulation for such conditions. This paper also shows that the model can be used effectively to study HVDC grids with significant time savings. [ABSTRACT FROM AUTHOR]

This paper proposes a model predictive control (MPC) method for modular-multilevel-converter (MMC) high-voltage direct current (HVDC). To control the MMC-HVDC system properly, the ac current, circulating current, and submodule (SM) capacitor voltage are taken into consideration. The existing MPC methods for the MMC-HVDC system utilize weighting factors to configure the cost function in combinations of the SM capacitor voltage balancing algorithm, ac current control, and circulating current control. Because all combinations of the switch states are considered in order to minimize the cost function, their possible combinations increase geometrically according to the increase of the level of the MMC, which is a significant disadvantage. This paper proposes a new MPC method with a reduced number of states for ac current control, circulating current control, and the SM capacitor voltage-balancing algorithm. The proposed cost functions are divided into three types according to their control purposes. Each cost function determines the minimum number of states for controlling the ac current, circulating current, and SM capacitor voltage. The efficacy of the proposed controlling method is verified through simulation results using PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

The model of a modular multilevel converter (MMC) determines the extent of critical circuit information that electromagnetic transient simulations can reveal. In this paper, two MMC models are proposed for efficient real-time hardware-in-the-loop (HIL) emulation on the field-programmable-gate-arrays (FPGA). The nonlinear switch-based model employing the insulated-gate bipolar transistor (IGBT) dynamic curve-fitting model considers factors affecting its transient performance so that device-level behavior such as power loss and junction temperature can be reproduced accurately in the electro-magnetic-thermal simulation of a power converter for its design evaluation. Meanwhile, regarding the MMC submodule as a transmission line stub achieves faster computation speed and enables the formation of a hybrid arm to save FPGA hardware resources. As the large network that the MMC presents is burdensome for real-time execution with a small time-step, circuit simplification based on partitioning and merging is conducted. Hardware implementation of a three-terminal high-voltage direct-current system containing an MMC-based dc–dc converter is carried out and the efficacy of proposed models is validated by comparing HIL emulation results with the offline simulation tool PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

This paper presents a breaker arrangement concept, the multiline breaker (MLB), for the protection of multiterminal high voltage dc (MTdc) networks. Based on the design of a hybrid breaker, the MLB is an economically attractive solution for the protection of multiple dc lines in nodal connection using a single main breaker path. By using commutation units, the MLB directs the fault current through the main breaker in a unidirectional way, irrespective of the fault location. Hence, this study presents the design requirements for the MLB, regarding both hardware and control, and evaluates its operation within a grid. For this reason, a four-terminal half-bridge multilevel modular converters-based MTdc grid in radial configuration was used and pole-to-ground dc fault conditions were investigated. The dc fault response of the grid with one MLB at the central node is compared to the respective response of the grid when one hybrid breaker is employed at each dc line. The simulations show that the MLB is feasible and that the overall MTdc grid fault response for the two protection systems is very similar. As a result, the design advantages of the MLB make it a promising solution for the dc fault isolation in MTdc grids. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC or M2C) is an emerging attractive multilevel topology for medium-voltage high-power applications. The capacitor voltage balancing control and the improvement of output current rating are two challenging issues of MMC. This paper proposed a new parallel-connected diode-clamped M2C (DCM2C), in which each arm consists of two parallel-connected clusters. In this topology, the capacitor voltages can be balanced automatically without any balancing control algorithms. Theoretically, no voltage sensors are needed to measure the capacitor voltages theoretically. Thus, the control of the converter can be simplified greatly. With a simple current-sharing control, an equal current distribution can be achieved between the two clusters. Furthermore, an extended parallel-DCM2C is proposed for larger current applications, and the corresponding current-sharing control method is developed. Experimental results validated the voltage self-balancing capability of parallel-DCM2C and the effectiveness of the proposed current-sharing control. [ABSTRACT FROM PUBLISHER]

Current-transformer (CT) saturation causes severe distortion in the measured current waveform which may lead to maloperation of the protective devices. This paper proposes a low-cost, power-electronic device to prevent the CT from saturation. The proposed compensator is inserted in series with the relay in the CT secondary circuit and acts as a controlled voltage source (CVS). The proposed CVS generates a time-varying voltage to cancel the voltage developed across the CT burden; therefore, the CT magnetic flux remains almost constant and undistorted during the power system transients. It will be shown that this device can precisely compensate fault current, inrush current, and other probable transient currents despite its simplicity. The proposed device can be employed to compensate the already in-service CTs connected to nondigital and digital relays. Comprehensive computer simulations are carried out to validate the effectiveness of the proposed compensator. The performance of a sample compensator of this type is validated through special high-current laboratory experiments (carried out over several hundred amperes up to 1.6 kA), and the obtained results illustrate the capability of the proposed compensator to prevent CT saturation. [ABSTRACT FROM PUBLISHER]

This paper proposes a startup sequence for a modular multilevel converter (MMC) HVDC-connected offshore wind farm (OWF) and demonstrates how it can be simulated using an electromagnetic transient-type tool. The objective is to analyze inrush currents of transformers and cables (HVAC and HVDC). Modeling accuracies and computational performances are examined using three existing modeling methods for the MMCs. [ABSTRACT FROM PUBLISHER]

This paper proposes an optimal design method of modular multilevel converter (MMC) levels to approach the reasonable compromise between accuracy and computational efficiency. The entire procedure is benchmarked by a Thévenin equivalent 451-level MMC model. First, the calculation method of the critical maximum simulation time step is proposed to faithfully represent each voltage level of the staircase waveforms. Second, the previously developed improved analytic hierarchy process is adopted to integrate the relative errors of all the main electrical parameters into one comprehensive relative error at each MMC level. Third, the steady state, ac, and dc transient state relative error results as well as the central-processing unit times of all models are normalized and curve fitted based on the benchmark model. Finally, the optimal MMC level is obtained by the plotted curves and the given subjective weights considering the accuracy and efficiency. And the effectiveness and robustness of the proposed method are validated by various simulation scenarios on PSCAD/EMTDC. [ABSTRACT FROM PUBLISHER]

Multimodule converter-based high-voltage dc (HVDC) power transmission incorporates numerous voltage-source converters (VSCs) connected in series/parallel to provide increased voltage/current and, hence, power ratings. When a selective harmonic elimination pulsewidth-modulation (SHE-PWM) technique is employed, the switching losses of the VSC modules are reduced but the voltages of the series-connected dc capacitors are not naturally balanced. In this paper, a voltage-balancing technique is reported. The technique relies on monitoring the voltage of each dc capacitor and when such voltage exceeds its preset band, the realization of the multilevel waveform reallocates the task to another VSC module to ensure that voltage balance between all capacitors is achieved. Three-phase bipolar VSC modules are considered in this paper and each one is modulated by a precalculated multilevel SHE-PWM waveform. The time-domain waveforms and their line-to-line voltage spectra are verified by simulation using PSCAD/EMTDC. The selected results are presented to confirm the viability of the proposed method. [ABSTRACT FROM PUBLISHER]

Double 12-pulse ultra HVDC transmission systems of \pm 800 kV and \pm 660 kV have larger transmission capacities, more complicated configurations, more complex operation modes, and more components, in comparison to \pm 500 kV or less HVDC transmission systems. Hence, the reliability evaluation of the ultra HVDC transmission system is more complicated than that of the HVDC system. To thoroughly describe different operating modes, this paper presents two new reliability measures for ultra HVDC transmission systems, that is, partial monopole forced outage times and partial bipole-forced outage times. Reliability evaluation models for individual subsystems, including converter transformers (CT), ac filters, converter valve groups, and smoothing reactors have been built considering operation modes and configuration characteristics. In particular, the reliability model of the CT subsystem was built by considering the type and the number of standby CTs, and that of the ac filter subsystem was built by considering the capacity state table of filters. A reliability evaluation model for ultra HVDC transmission systems was proposed by combining reliability logic relationships among subsystems and using the state enumeration method. Case studies of practical ultra HVDC transmission systems illustrate the correctness of indices and the proposed models. In addition, sensitivity analysis and standby analysis of major components were also conducted. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) has become one of the most promising converter topologies for medium/high-power applications. Since the MMC is structured based upon stacking up a number of series-connected identical submodules (SMs), to improve its fault tolerance and reliability, SM failure detection and location is of significant importance. In this paper, the impact of open-circuit switch failures of the SMs on the operation of the MMC is analyzed. Based on the analysis under SM failure conditions, two SM failure detection and location methods are proposed, that is, a clustering algorithm (CA)-based method and a calculated capacitance (CC)-based method. In the proposed CA-based method, a pattern-recognition-based fault diagnosis approach, which employs the clustering algorithm to detect and locate the faulty SMs with open-switch failures through identifying the pattern of 2-D trajectories of the SM characteristic variables, is developed. The proposed CC-based method is based on the calculation and comparison of a physical component parameter, that is, the nominal SM capacitance, and is capable of failure detection, location, and classification within one stage. The performance of the proposed failure detection methods for an MMC system is evaluated based on time-domain simulation studies in the PSCAD/EMTDC software environment. The reported study results demonstrate the capabilities of the two proposed methods in detecting and locating any SM failure under various conditions accurately and efficiently. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) is based on the cascaded connection of identical submodules (SMs) enabling additional redundancies. This paper proposes the configuration of the MMC topology with redundant SMs and demonstrates the effects of active redundancies. The proposed configuration decreases the switching frequency per SM while reducing the SM capacitor voltage ripples. An analytical model for determining the SM capacitor voltage ripple and voltage dynamics is derived. The results from the analytical model are compared with the switching model for a 21-level MMC with five redundant (25 in total) SMs per arm. Experimental results based on a single-phase laboratory prototype with five SMs per arm and a single redundant cell further illustrate the operation and verify the derived mathematical model and simulation results. [ABSTRACT FROM AUTHOR]

Proper operation of a multilevel flying capacitor converter (FCC) necessitates a closed-loop voltage balancing strategy. This paper proposes a space vector modulation (SVM)-based approach that benefits from the switching state redundancy of an n-level FCC to implicitly carry out the voltage balancing task within the switching strategy. Based on the voltage deviations of the capacitor voltages, a cost function is defined and minimized to choose the proper redundant switching states among the available switching states. The performance of a grid-connected four-level FCC under the proposed SVM strategy for various operating conditions is studied and evaluated based on time-domain simulations in the PSCAD/EMTDC environment, and experimentally verified. The studies demonstrate the capability of the proposed SVM strategy to regulate the capacitor voltages at their nominal reference values. [ABSTRACT FROM AUTHOR]

This paper applies nearest level control (NLC) to the modular multilevel converter (MMC). Since there are a number of submodules (SMs) in high-voltage applications of MMC and all SM voltages are required to be measured and sorted, if the uniform sampling frequency is not high enough, the SM will not be triggered as quickly as possible. Thus, the converter-output voltage levels and voltage harmonics will be affected. A method to systematically analyze the voltage harmonics is presented, considering the uniform sampling frequency. In order to select a proper sampling frequency, two critical values, which significantly influence the output voltage levels and voltage total harmonic distortions, are calculated. Simulation results based on PSCAD/EMTDC proved the validity of the proposed modulation scheme and the importance of a properly selected sampling frequency. [ABSTRACT FROM AUTHOR]

This paper presents a neutral point voltage control strategy for the three-level active neutral point clamped (ANPC) converter using selective harmonic elimination pulsewidth modulation (SHE-PWM). The control strategy introduces a small change in the switching angles, which varies the duty cycle of the zero-level switching state, controls the neutral point current and, therefore, the neutral point voltage. The decision to vary a given switching angle takes into account the polarity of the output currents and the voltage across the lower dc-link capacitor. The effectiveness of the proposed strategy is verified through extensive simulation studies and experimentally validated using a low power laboratory prototype. [ABSTRACT FROM AUTHOR]