Search

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

With the advancements of the battery energy storage systems (BESSs), reduction of their manufacturing costs and government subsidies, the BESS uptake is likely to increase rapidly in power distribution networks. This paper investigates the effects of residential BESSs on low-voltage (LV) networks using the actual household load profiles equipped with BESS and solar-photovoltaic (PV) systems. The electricity consumption data collected via smart meters (2200 households with PV/BESS, 1950 households with PV only and 1000 households without a PV or a BESS) at different solar-PV penetration levels and network types are used to simulate real network operating scenarios. A real LV distribution network in Australia is analysed in DIgSILENT PowerFactory under different scenarios, such as, customers with and without a solar-PV/BESS, with a solar-PV but without a BESS, and without a solar-PV, by using both the power flow and quasi-dynamic simulation studies under balanced and the unbalanced network loading conditions. According to the study, customers experience large voltage excursions from solar-PV power exports, which could be resolved by the household BESS, provided that the BESS charging is coordinated with the solar-PV production. Moreover, quasi-dynamic simulation shows that the BESS could reduce the violation of the over-voltage limit during the solar peak hours (midday) by lowering the worst-case feeder voltage by 3%. Finally, extreme-event (high solar PV generation scenario) simulation shows that the implementation of the BESS controller to facilitate charging BESS during afternoon solar-PV export may reduce the negative grid impact and will assist to avoid network upgrades. [ABSTRACT FROM AUTHOR]

This paper proposes a novel reactive power-based control strategy for single-phase PV inverters (PVIs) to simultaneously improve voltage unbalance (VU) and voltage regulation (VR) in low-voltage distribution networks. The proposed strategy relies on communication links between neighboring PVIs to exchange limited data. In this strategy, each PVI finds communication paths between itself and the closest neighboring ones connected to other phases. Then, using the obtained paths and the maximum and the minimum voltage magnitude of the grid, PVIs improve both VU and VR at the same time. The performance of the proposed control strategy is evaluated by various simulation studies using the IEEE European low-voltage test feeder and considering different operational conditions. In addition, the impacts of moving clouds and a failure in the communication links have been assessed. The simulation results exhibit that using the proposed control strategy, the voltage magnitude of all the nodes will remain within the allowed limits and at the same time, the phase voltage unbalance factor will be also significantly improved. [ABSTRACT FROM AUTHOR]

Operational performance in the low-voltage distribution network (LVDN) can be undermined by its inherent unbalances, which may become worse as the penetration of rooftop solar continuously increases. To address this issue, load balancing via phase-reconfiguration devices (PRDs), which can change phase positions of residential customers as required, provides a cost-efficient option. However, most reported approaches to control PRDs require that demands of all residential customers are available, which are not viable for many LVDNs without smart meters or advanced metering infrastructure (AMI) installed. To bridging the gap in this field, this paper proposes a novel method to control PRDs purely based on measurable data from PRDs, and its controller. Based on limited information, sensitivity analysis in the network with PRDs is studied, followed by the optimization model that comprehensively considers operational requirements in the network. Moreover, slack variables are introduced to the model, and penalized in the objective function to assure either a strategy that is secure or with minimized violations can always be provided. The model is a challenging mixed-integer non-convex programming (MINCP) problem, which is reformulated as an efficient solvable mixed-integer second-order cone programming (MISOCP) based on exact reformulations or accurate linear approximations. Simulations based on two modified IEEE systems, and a real system in Australia demonstrate that an efficient strategy can be provided to mitigate unbalances in the network. [ABSTRACT FROM AUTHOR]

This paper proposes a novel peak load management scheme for rural areas. The scheme transfers certain customers onto local nonembedded generators during peak load periods to alleviate network under voltage problems. This paper develops and presents this system by way of a case study in Central Queensland, Australia. A methodology is presented for determining the best location for the nonembedded generators as well as the number of generators required to alleviate network problems. A control algorithm to transfer and reconnect customers is developed to ensure that the network voltage profile remains within specification under all plausible load conditions. Finally, simulations are presented to show the performance of the system over a typical maximum daily load profile with large stochastic load variations. [ABSTRACT FROM AUTHOR]