Search

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

A novel single-stage doubly grounded transformerless inverter configuration which can buck-boost the output voltage is proposed in this paper. In this transformerless inverter configuration grid neutral is directly connected to PV panel negative rail which suppresses/eliminates the PV leakage currents. In addition, the tracking of maximum power point is possible for wide variation of weather conditions due to buck-boost voltage capability of inverter. Moreover, the proposed inverter topology has symmetrical operation in both half cycles hence injects negligible DC offset current in to the grid. Here the symmetrical operation of inverter is achieved due to one inductor is used for both half cycles of the grid. The proposed topology is realized using five switches, two of which work at 50 Hz and remaining three switches at high frequency which reduces overall semiconductor losses. Further, the proposed inverter topology is controlled through a newly developed modulation technique and possible working modes are analyzed and described thoroughly. For performance validation, the experimental analysis of grid connected proposed inverter is performed on a 1 kVA system and results show that proposed inverter feeds power in to the grid with lesser THD while achieving greater efficiency. [ABSTRACT FROM AUTHOR]

When a fault occurs on the dc side of the voltage source converter based high voltage direct current (VSC-HVDC) transmission system, the fault current rises quickly due to the low damping of the dc system. Using a dc fault current limiter (DC-FCL) to limit the rise of the fault current can significantly reduce the breaking requirements of the DCCB. A topology of a bidirectional active dc fault current limiter (BA-FCL) based on coupled inductor is proposed in this paper. No expensive full-controlled power electronic devices are used in this topology. Only a few half-controlled power electronic devices are used to achieve active control of the current limiting unit. Compared with many topologies of current limiter at present, the fault current limiting effect of BA-FCL is improved significantly while the cost, volume, topology complexity, and control complexity are reduced. The stress analysis and parameter design of the proposed current limiter are carried out. Finally, the simulation case study and hardware experiment are implemented to verify the good economy and current limiting performance of the proposed topology. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

In high power applications, 3-phase ac/dc Voltage Source Converters (VSCs) are paralleled to increase the overall aggregated converter power rating, effective switching frequency and control bandwidth. For this, interleaved Pulse Width Modulation (PWM) and current limiting paralleling inductors are required. Interphase Transformers (ITRs) are often used for the converter paralleling because they provide large magnetizing inductances for the currents flowing between the converters while introducing negligible leakage inductances for the currents flowing from the converters to the ac grid. This large asymmetry in the inductance values makes it difficult to independently control active power flows in the individual converters. Thus, if the converters dc buses are not mutually interconnected, instabilities in active control of balance of converter dc bus voltages can occur in certain operational conditions. This paper presents a theoretical analysis of the active power flows produced by the currents flowing among the converters and explains origins of potential instability in the active control of balance of dc bus voltages in multi-converter systems with floating dc buses, paralleled using the ITRs. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) based high voltage direct current (HVDC) transmission system is one of the important development trends of DC power grid. After fault isolation, the traditional reclosing method of MMC-HVDC system is directly reclosing DC circuit breaker (DCCB). Once the fault point still exists, DCCB will be tripped again. This method will make the DC system suffer from the secondary strike of fault in a short time, and seriously endanger the service life of DCCB. In order to overcome the drawbacks of the traditional reclosing schemes, this paper proposes a novel adaptive reclosing scheme based on pulse injection from parallel energy absorption module. When dc fault current is interrupted by DCCB, the fault energy stored in current-limiting reactors (CLR) and dc lines is transferred to energy absorption module automatically. By switching on IGBTs embedded in absorption module for a short time, a voltage pulse is injected directly into the faulty line without interference from CLR. Then the nature of fault is identified and the fault distance can also be calculated in the case of permanent faults. The simulation results verify the effectiveness of the proposed reclosing scheme. [ABSTRACT FROM AUTHOR]

Recently the hybrid multi-port DC circuit breaker (MP-DCCB) is becoming popular in protecting HVDC grids, thanks to their reduction of power electronics devices. In this paper, an enhanced multi-port current-limiting DCCB (MP-CLCB) for multiple line protection is proposed. The integrated fault current limiter (FCL) inside the MP-CLCB can clear the fault faster with slightly increased costs. To reduce the energy dissipation requirement for the surge arresters caused by the newly added current-limiting path, an energy transfer path which provides a loop with the inductors during the current decay stage is designed. The theoretical analysis of the pre-charging, current-limiting, fault interruption and energy dissipation of the MP-CLCB is carried out. Moreover, the design principles of the energy dissipation and the key parameters of the MP-CLCB are provided. The proposed approaches are verified through simulations in PSCAD/EMTDC. The results show that the MP-CLCB can replace multiple DCCBs, accelerate the fault current interruption and reduce the energy dissipation requirement for the surge arresters. [ABSTRACT FROM AUTHOR]

High-voltage direct-current system based on modular multilevel converter (MMC-HVDC) is widely expected to plays a significant role in promoting the development of large-scale offshore wind power. The maximum current limit of insulated-gate bipolar transistor (IGBT) is the main constrain for MMC-HVDC to operate in large current operation, while DC-fault blocking ability and economy are the two important concerns of MMC-HVDC. This paper proposes a novel parallel multiple submodule (PM-SM) topology to realize parallel output of submodule currents, which make MMC capable of large current operation and have filtering effect on high frequency harmonics. Combining with carrier phase-shift modulation or nearest level modulation, the frequency multiplication of bridge arm current of MMC can be realized to further improve the power quality of the system. Considering the demand of DC-fault blocking ability, simplified full-bridge double submodule (S-FBDSM) is also proposed as an economical option to compose PM-SM. It can provide double the reverse capacitance voltages in the arm current path regardless of a positive or negative arm fault current. The economic analysis is conducted to demonstrate the advantage of S-FBDSM. Simulation results and experiment results verify the feasibility and superiority of PM-SM composed of S-FBDSM. [ABSTRACT FROM AUTHOR]

DC–DC converters are expected to interconnect High Voltage Direct Current (HVDC) grids with different configurations or voltage levels, which will increase reliability and operational flexibility. The dc Modular Multilevel Converter (DC-MMC) is suggested as a potential non-isolated topology for HVDC applications. This paper presents an energy-based closed-loop control for the DC-MMC. Such control structure provides a full control of the current components, while ensuring energy balancing in normal and fault operation. First, the converter configuration is described and the fundamental equations are presented. Then, the normal operation of the converter is explained from the steady state conditions and the energy and current components. A closed-loop control is designed to ensure a proper dynamic response, balance the internal energies of the converter, and minimize the ac circulating current. Also, the control structure is modified to ensure dc fault ride through capability. Simulation results in MATLAB/Simulink are used to validate the converter control under normal operation and DC faults. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC or M2C) is an emerging attractive multilevel topology for medium-voltage high-power applications. The capacitor voltage balancing control and the improvement of output current rating are two challenging issues of MMC. This paper proposed a new parallel-connected diode-clamped M2C (DCM2C), in which each arm consists of two parallel-connected clusters. In this topology, the capacitor voltages can be balanced automatically without any balancing control algorithms. Theoretically, no voltage sensors are needed to measure the capacitor voltages theoretically. Thus, the control of the converter can be simplified greatly. With a simple current-sharing control, an equal current distribution can be achieved between the two clusters. Furthermore, an extended parallel-DCM2C is proposed for larger current applications, and the corresponding current-sharing control method is developed. Experimental results validated the voltage self-balancing capability of parallel-DCM2C and the effectiveness of the proposed current-sharing control. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) has become an attractive option for dc/ac conversion in many power system applications, in particular, for HVDC transmission. Due to its parallel arrangement of phase legs, the MMC is known to be a wye-configured architecture. In this paper, the equivalent delta formulation of the conventional wye architecture is introduced. The delta-configured MMC, enabled by series-stacking phase legs, is an alternative realization to the wye-configured MMC and has significantly different operating characteristics. The introduction of the delta MMC enables greater flexibility in converter voltage/current scaling for a given set of submodules, and may be an appealing option for dc/ac applications requiring a power tapoff from a high-voltage dc rail. The single-ended and differential delta topologies are derived, with the latter seen as the preferred topology due to its reduced energy-storage requirements. The principle of operation of the differential delta-configured MMC is described in detail. A dynamic controller is developed that regulates grid power injections while suppressing unwanted circulating ac currents. Comprehensive simulation results validate the differential delta MMC operation and the proposed control scheme. [ABSTRACT FROM AUTHOR]

This paper investigates a new family of converters for high-power transfer between dc buses with different voltage levels. The proposed converters achieve high-voltage dc-dc conversion without an intermediate ac conversion stage. Three converter circuits are investigated, all based on the use of a common switching cell module. The first is a step-down converter, the second is a step-up converter, and the third is an inverting step-up/downconverter. For each converter, the structure is presented, its operation principle is explained, and the design equations are derived. A comparative analysis between the converters is carried out to highlight the merits and limitations of each topology. [ABSTRACT FROM PUBLISHER]

This paper proposes an LCL dc-dc converter concept which is capable of achieving very high stepping ratios with megawatt-level power transfers. The converter can find potential application in connecting high-power dc sources to high-voltage dc transmission including future dc transmission networks. This converter is based on two ac/dc insulated-gate bipolar transistor-based converters and an internal passive LCL circuit without internal ac transformers. The LCL circuit is designed to enable voltage stepping without any reactive power circulation and with potentially soft switching operation which minimizes the switching losses. The designed converter has the ability to achieve current regulation even under extreme external dc faults and, therefore, the converter can operate through dc faults. The switch utilization is better than similar topologies and losses are reasonably low. A dual-active-bridge transformer-based converter design is presented to compare with the proposed LCL converter. A detailed PSCAD model confirms conclusions using a 100-MW 20-kV/300 kV test system. An LCL 200-W 20-V/100-V dc/dc prototype converter is built to validate the proposed topology. [ABSTRACT FROM AUTHOR]