Search

Due to the still increasing penetration of grid-connected photovoltaic (PV) systems, advanced active power control functionalities have been introduced in grid regulations. A power reserve control, where namely the active power from the PV panels is reserved during operation, is required for grid support. In this paper, a cost-effective solution to realize the power reserve for two-stage grid-connected PV systems is proposed. The proposed solution routinely employs a maximum power point tracking control to estimate the available PV power and a constant power generation (CPG) control to achieve the power reserve. In this method, the solar irradiance and temperature measurements that have been used in conventional power reserve control schemes to estimate the available PV power are not required, and thereby, being a sensorless approach with reduced cost. Experimental tests have been performed on a 3-kW two-stage single-phase grid-connected PV system, where the power reserve control is achieved upon demands. [ABSTRACT FROM AUTHOR]

Over recent years, the output power of micro-inverters [module-incorporated inverter (MIC)] is progressively pushed to higher levels, following the current photovoltaic (PV) modules market trends. The interleaved Flyback inverter—under discontinuous conduction mode of operation (DCM)—is an appealing solution for PV applications which are based on MIC technology. This topology provides increased power level for distributed PV generation exploitation with simple control configuration, high efficiency, and reduced filter size. In this paper, the harmonic injection capability is incorporated into the interleaved Flyback inverter for the implementation of an active anti-islanding scheme. A suitable technical solution is proposed that bypasses the unfolding H-bridge, without affecting the active power generation of the inverter and without requiring any hardware modification. In addition, a mathematical model based on the instantaneous power balance theory is presented, being a powerful analysis tool for inverters operating under complete magnetic discharge such as the Flyback inverter (either conventional or interleaved) under DCM or boundary conduction mode of operation. The proposed model predicts accurately the steady-state operational behavior of the Flyback inverter under current harmonic injection, either in grid-tied or islanding operation. The proposed technical implementation method and mathematical model are verified through simulation and experimental results. Finally, an anti-islanding set-up based on the proposed harmonic injection technique is presented and implemented into the Flyback micro-inverter. The proposed set-up is verified through experimental results on various quality factor values, as well as for weak grid conditions. [ABSTRACT FROM AUTHOR]

Variable switching frequency pulse width modulation (VSF PWM) has been proposed in the past to optimize the total harmonic distortion (THD) performance and switching losses of an inverter. Nevertheless, such VSF PWMs give rise to switching harmonics which vary across a wide frequency spectrum, where the lower frequencies could resonate with the filter while the upper frequency could exceed the maximum switching frequency. This complicates VSF PWM design, restricting their practical uses. In this paper, a confined band VSF PWM (CB-VSF PWM) for a single-phase inverter with an LCL filter is presented. By confining the switching frequencies within a practical band, the design of the filter becomes easier while maintaining low current THD with low switching losses. The choices of the upper and lower bands of the proposed VSF are defined and the design criterion is introduced. It is found that the proposed method allows reduction in switching losses as well as reduction in current THD when the effect of the LCL filter is taken into consideration. The performance analysis is validated through simulation and experimental results in a 1 kW inverter. [ABSTRACT FROM AUTHOR]

In the past two decades, the operating voltage of photovoltaic (PV) installation has increased in order to reduce current ratings and system installation costs. Such a large number of PV panels in series (e.g., 1000–1500 V systems) lead to wide variations of PV voltage due undesirable effects such as shading, soiling/dust, aging, and hot surface temperature. A partial shade would normally shut down solar inverters, unless a boost stage is added to the system input to ensure a proper dc-link operating voltage for the inverter. A boost input stage can double the input voltage operating range to extract maximum power under any possible shading and temperature condition. In this paper, a new PV string boost topology arrangement is proposed in the form of a miniboost used for three-phase grid-connected converters. The string miniboost increases the dc voltage range to extend power extraction under shading and low irradiance conditions and only requires to process a fraction of the rated power. The proposed cost-effective solution is further improved by using the inverter peak power envelope at boundary operation, resulting in expanded energy extraction beyond existing techniques. A design procedure to optimally size the miniboost and the peak-power envelope is presented along with a comparative analysis, under different irradiance levels, to illustrate the advantages in energy extraction obtained with the proposed PV string miniboost solution under low voltage and boundary operation. Furthermore, improved efficiency operation schemes and issues of common-mode current are discussed, and three mitigation design techniques intended for three-phase, three-level inverter transformerless topology are presented. Simulations and experimental results using a dual miniboost dc–dc stage and three-phase three-level neutral point clamped inverter are presented to validate the proposed dc-bus extension range and system design. [ABSTRACT FROM AUTHOR]

Inverters and loads can freely connect to any node in a meshed parallel inverters system, leading to variations of line impedance between two nodes and the structure of the electric network. More challenges exist for proportional load-sharing control in such a system. An improved proportional load-sharing strategy for a meshed parallel inverters system with complex impedances is proposed in this paper. The RL-type droop method is modified through injecting the power droop information of all other inverters, which can improve the load-sharing accuracy to some extent and completely compensate the voltage amplitude and frequency deviations caused by droop equations under accurate load-sharing conditions. Besides, an adaptive virtual resistance tuned by the integral of the linear combination of output active and reactive powers, is added to eliminate load-sharing errors. In addition, the central controller broadcasts the control variables to all inverters. This improves the simultaneity of control data and minimizes the mismatch of control delay. Three modified droop methods are compared with the small-signal analysis and simulation. Experimental results are presented to investigate the performance of the proposed control strategy. [ABSTRACT FROM PUBLISHER]

This paper analyzes the stability of digitally voltage-controlled voltage-source inverters (VSIs) with the linear voltage regulators. It is revealed that the phase lags, caused by using the resonant controller and the time delay of a digital control system, can stabilize the single-loop voltage control without damping of the LC -filter resonance. The stability region for the digital single-loop resonant voltage control is then identified, considering the effects of different discretization methods for the resonant controller. An enhanced voltage control approach with a widened stability region is subsequently proposed, and a step-by-step design method of the proposed controller is developed based on the root contours in the discrete z-domain. Simulations and experimental tests of a 400-Hz VSI system validate the stability analysis and the performance of the proposed control approach. [ABSTRACT FROM PUBLISHER]

When employed as a modulator in power inverters, model predictive control has an equivalence to a recently proposed modulation technique known as feedback quantizer modulation (FBQM). Both schemes produce a random-like switching pattern that can facilitate explicit control over the shape of frequency spectra associated with inverter output voltages and currents. This is useful to satisfy electromagnetic interference and acoustic noise requirements, and to avoid excitation of external system resonances. However, it will be shown in this paper that inverter deadtime introduces a disturbance into FBQM that significantly degrades the ability to shape the frequency spectra. Several compensation techniques, designed to model the effect of deadtime inside the formulation of FBQM, are proposed and experimentally verified on a two-level three-phase inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a comprehensive and practical method of implementing speed range extended maximum torque per ampere (MTPA) control for permanent magnet synchronous machine (PMSM) is presented. The inverter-based method of measuring PMSM parameters, including winding resistance and d- and q-axis flux linkages, is introduced. The nonlinearities of the inverter, including voltage amplitude error and voltage phase shift, are identified and compensated, which improves the accuracy of the characterized flux linkage. The extended MTPA current references are obtained by employing nonlinear optimization algorithm, and the results are verified analytically on the current plane. MTPA control is applied on the PMSM experimentally in the entire speed range. Current transition, torque control accuracy, and efficiency performance are measured in the entire torque–speed range. [ABSTRACT FROM PUBLISHER]

This paper presents a steady-state model of MMC for the second-order phase voltage ripple prediction under unbalanced conditions, taking the impact of negative-sequence current control into account. From the steady-state model, a circular relationship is found among current and voltage quantities, which can be used to evaluate the magnitudes and initial phase angles of different circulating current components. Moreover, in order to calculate the circulating current in a point-to-point MMC-based HVdc system under unbalanced grid conditions, the derivation of equivalent dc impedance of an MMC is discussed as well. According to the dc impedance model, an MMC inverter can be represented as a series connected R–L–C branch, with its equivalent resistance and capacitance directly related to the circulating current control parameters. Experimental results from a scaled-down three-phase MMC system under an emulated single-line-to-ground fault are provided to support the theoretical analysis and derived model. This new models provides an insight into the impact of different control schemes on the fault characteristics and improves the understanding of the operation of MMC under unbalanced conditions. [ABSTRACT FROM PUBLISHER]

To solve the problem of the mismatched voltage levels between the dynamic lower voltage of the fuel cell stack and the required constant higher voltage (400 V) of the dc-link bus of the inverter for fuel cell vehicles, a boost three-level dc–dc converter with a diode rectification quasi-Z source (BTL-DRqZ) is presented in this paper, based on the conventional flying-capacitor boost three-level dc–dc converter. The operating principle of a wide range voltage-gain for this topology is discussed according to the effective switching states of the converter and the multiloop energy communication characteristic of the DRqZ source. The relationship between the quasi-Z source net capacitor voltages, the modulation index, and the output voltage is deduced and then the static and dynamic self-balance principle of the flying-capacitor voltage is presented. Furthermore, a boost three-level dc–dc converter with a synchronous rectification quasi-Z source (BTL-SRqZ) is additionally proposed to improve the conversion efficiency. Finally, a scale-down 1.2 kW BTL-SRqZ prototype has been created, and the maximum efficiency is improved up to 95.66% by using synchronous rectification. The experimental results validate the feasibility of the proposed topology and the correctness of its operating principles. It is suitable for the fuel cell vehicles. [ABSTRACT FROM PUBLISHER]

In signal injection sensorless drives, the injection voltage cannot be reduced under a certain value. The lower limit of the injection voltage is mainly enforced by the inverter nonlinearity that causes distortion of the injection voltage and degradation of the position estimation performance. After analyzing the inverter nonlinearity during the voltage injection, it is revealed that parasitic capacitances of insulated-gate bipolar transistors have positive effects on inverter output linearity and sensorless control. Based on this analysis, this paper proposes a method to reduce the injection voltage by connecting additional capacitors to the output terminals of the inverter. Simulation and experimental results are provided to verify the effectiveness of the proposed idea. In the experiments, using the capacitor-integrated inverter, it is shown that the injection voltage can be reduced by more than half without degrading the position estimation performance. [ABSTRACT FROM AUTHOR]

High-order wide-output (HOWO) impedance-source converters (ISCs) have been presented for ac inverter applications that require voltage step-up ability. With intrinsic passive impedance networks as energy sources, these converters are able to achieve voltage boosting with either polarity, leading to improved dc-link voltage utilization compared with the conventional two-level converter. However, HOWO-ISCs suffer from transfer functions giving low bandwidth, a penalty of increased passive devices and right-half-plane zeros, which result in lower order distortion of the ac output power. In this paper, a modified plug-in repetitive control scheme is presented for HOWO-ISCs with accurate reference tracking (hence low distortion), fast dynamic response, and enhanced robustness. By using zero-phase-shift finite impulse response filters in both the internal model of the repetitive controller and its compensation network, the proposed method achieves zero steady-state error and an extended closed-loop bandwidth. For HOWO-ISC cases, this method outperforms conventional proportional-integral (PI) control, which has considerable steady-state error. It also eliminates the need of parallel loops for several frequencies when proportional resonant control or orthogonal transformation-based PI schemes are used to remove lower order distortion. The design process and performance analysis of the proposed repetitive control strategy are based on a novel three-phase HOWO-ISC configuration with a reduced number of switches. Simulation and experimental results confirm the feasibility and effectiveness of the proposed control approach. [ABSTRACT FROM AUTHOR]

This paper proposes an iterative learning control (ILC) scheme for a dual-mode flyback inverter operating in both discontinuous conduction mode (DCM) and continuous conduction mode (CCM). In dealing with more than 200-W power applications, the dual-mode flyback inverter takes advantage of both DCM and CCM operations. However, it is difficult to control the output current because the system gain is quite low in DCM and the system transfer function has a right-half plane zero in CCM. To overcome the problems occurring in DCM and CCM operations, we propose an ILC scheme with multiple phase-lead compensation. The ILC is proposed to achieve accurate reference tracking and to reject periodic disturbances. The multiple phase-lead compensation technique is then employed to compensate for the effect of different system dynamics. As a theoretical result, we derive the asymptotic stability of the closed-loop system. We also performed the numerical simulations and experimental tests to validate the proposed control approach. [ABSTRACT FROM AUTHOR]

This paper describes a variable-speed motion-sensorless control system for permanent-magnet synchronous generator (PMSG) connected to grid via back-to-back inverters for wind energy generation. The grid-side inverter control system employs proportional-integral (PI) current controllers with cross-coupling decoupling and line-voltage feedforward disturbance compensation. Also, a D-module filter is used to robustly extract the line voltage positive sequence followed by a phase-locked-loop (PLL) based observer to estimate the positive-sequence angle for control, including the case of asymmetric voltages and automatic seamless transfer method from grid connected to stand alone and vice versa. In stand-alone mode, a voltage control scheme with selective harmonic compensation is employed. The PMSG motion-sensorless control system uses an active power controller and a PLL-based observer to estimate the rotor position and speed without using the electromotive force (EMF) integration and initial rotor position. The paper investigates and validates the ride-through performance of this proposed system during asymmetric power grid-voltage sags, transition from grid connected to stand alone and vice versa and voltage harmonics compensation. While some of the aforementioned issues have been treated rather individually in previous conference publications of the authors, the present paper integrates them into a comprehensive control system of PMSG. [ABSTRACT FROM AUTHOR]

A new zero-sequence circulating current (ZSCC) reduction method for multimodule voltage source inverters (MVSIs) consisting of P three-phase inverters that are connected in parallel is proposed in this paper. Four-switch inverter modules are used instead of the conventional six-switch modules to reduce the cost. In this paper, the effectiveness of the proposed ZSCC reduction method is studied using selective harmonic elimination pulse width modulation. The proposed ZSCC reduction method can remove about P times the number of harmonics using the same switching frequency as compared to more conventional methods, as explained later in this paper. The concepts discussed in the paper are confirmed with results obtained from an MVSI experimental prototype. [ABSTRACT FROM AUTHOR]

The purpose of this paper is to investigate the model, control, and implementation of a multifunction grid-interfaced inverter with output LCL filter, which can provide high performance active power current and compensate the existent harmonics simultaneously in a distributed network. Equipped with LCL filter, the proposed multifunction inverter offers reduced switching harmonics and superior output current shapes. However, the multifunction inverter with output LCL filter brings some challenges, including LCL resonance, phase lag, and complexity in system design. To address these issues, this paper analyzes and develops general Thevenin/Norton models for the multifunction grid inverters with LCL filter. Based on the general models of system, this paper presents guidelines of the control and the procedure of filter design for this application. In particular, a proportional-resonant (PR) plus odd-harmonic repetitive control (OHRC) scheme is designed for the outer current loop. The phase compensation method and detailed design criteria for the proposed control scheme are presented. Furthermore, the proposed OHRC scheme is compared with the previous multiple resonant control (MRC) based on their internal relationship. Simulation and experimental results are provided to validate the effectiveness and advantages of the proposed control strategy. [ABSTRACT FROM AUTHOR]

This paper investigates the capacitor-current-feedback active damping for the digitally controlled LCL-type grid-connected inverter. It turns out that proportional feedback of the capacitor current is equivalent to virtual impedance connected in parallel with the filter capacitor due to the computation and pulse width modulation (PWM) delays. The LCL-filter resonance frequency is changed by this virtual impedance. If the actual resonance frequency is higher than one-sixth of the sampling frequency (fs/6), where the virtual impedance contains a negative resistor component, a pair of open-loop unstable poles will be generated. As a result, the LCL-type grid-connected inverter becomes much easier to be unstable if the resonance frequency is moved closer to fs/6 due to the variation of grid impedance. To address this issue, this paper proposes a capacitor-current-feedback active damping with reduced computation delay, which is achieved by shifting the capacitor current sampling instant towards the PWM reference update instant. With this method, the virtual impedance exhibits more like a resistor in a wider frequency range, and the open-loop unstable poles are removed; thus, high robustness against the grid-impedance variation is acquired. Experimental results from a 6-kW prototype confirm the theoretical expectations. [ABSTRACT FROM AUTHOR]

Silicon carbide (SiC) based power semiconductors are expected to contribute to an increase in inverter efficiency, switching frequencies, maximum permissible junction temperature, and system power density. This paper presents a comparison of silicon (Si) and SiC device technologies for the use in hybrid electric vehicle traction inverters. SiC-JFETs and SiC-MOSFETs are characterized and a scalable loss and scalable thermal modeling approach is used to find the optimum chip area for each Si or SiC traction inverter. This procedure also provides a proper technical comparison of the semiconductor technologies. The progressed simulations using standardized drive cycles and thermal-electrical coupled semiconductor models permit an inverter performance evaluation close to real load situations, leading to an improved estimation of the benefit which can be expected from systems utilizing SiC technology. This paper concludes that the SiC devices can lead to a reduction in chip area and semiconductor losses by more than 50% at the same time in hard switching applications with partial load dominated mission profiles. [ABSTRACT FROM AUTHOR]

This paper presents a comparison of the behavior of the intrinsic diode of silicon (Si) and silicon carbide (SiC) MOSFETs. The study was done for 1200 V Si and SiC MOSFETs. The data sheet from manufacturers shows the characteristics of MOSFET' intrinsic diode when gate source voltage (VGS) is 0 V. There are applications where the MOSFET' intrinsic diode is used while VGS is different than 0 V. One of these applications is induction heating, where depending on the load and the regulation system, the diode can conduct a significant part of the inverter current. In most applications which use the MOSFET' intrinsic diode, the turn ON of the intrinsic diode happens at VGS = 0 V. After a blanking time, the MOSFET' gate is activated waiting for the direction change of current in the circuit. Therefore, most of the current through the MOSFET' intrinsic diode occurs with a VGS different of 0 V. This paper shows the direct output characterization of Si and SiC MOSFET' intrinsic diode under different gate voltages. The gate resistor (RG) is an important parameter of the characterization. Depending on the input capacitance of the Si or SiC MOSFET, different RG are needed. The turn-on and turn-off behaviors are obtained when RG is optimized for each Si and SiC MOSFET. This has result in the turn-off robustness of intrinsic diode with optimum RG. This paper presents a surprising result for the reverse characteristic of Si and SiC MOSFETs for the same current at different VGS. The technology of Si MOSFET has different behavior depending on the manufacturer. The technology of SiC MOSFET presents a very similar behavior to low-voltage Si MOSFETs. [ABSTRACT FROM AUTHOR]

This paper presents a unified control strategy that enables both islanded and grid-tied operations of three-phase inverter in distributed generation, with no need for switching between two corresponding controllers or critical islanding detection. The proposed control strategy composes of an inner inductor current loop, and a novel voltage loop in the synchronous reference frame. The inverter is regulated as a current source just by the inner inductor current loop in grid-tied operation, and the voltage controller is automatically activated to regulate the load voltage upon the occurrence of islanding. Furthermore, the waveforms of the grid current in the grid-tied mode and the load voltage in the islanding mode are distorted under nonlinear local load with the conventional strategy. And this issue is addressed by proposing a unified load current feedforward in this paper. Additionally, this paper presents the detailed analysis and the parameter design of the control strategy. Finally, the effectiveness of the proposed control strategy is validated by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Aiming at overcoming the problem that the auxiliary commutation circuit (ACC) of auxiliary resonant commutated pole (ARCP) inverters has a high loss in commutation processes, this paper presents a novel modulation strategy based on an improved ARCP inverter. In comparison with the original modulation strategy, this modulation strategy can not only realize soft-switching for all switches, but also avoid the superposition of resonance current and load current at commutation moments in ACCs and make the maximum current through ACCs approximately equal to load current in commutation processes. So the circulating current loss in ACCs and the current peak stress of auxiliary switches can be effectively reduced. According to the equivalent circuit in different operation modes under this modulation strategy, this paper analyses the operation principle, soft-switching implementation condition, and optimal parameter design procedure of the improved ARCP inverter. Finally, the novel modulation strategy is applied to a 10 kW 16 kHz improved ARCP inverter prototype with insulated gate bipolar transistor-based switches. Experimental results are given to demonstrate the validity and features of the inverter under the novel modulation strategy. [ABSTRACT FROM AUTHOR]

This paper describes phase current reconstruction methods from dc-link currents in three-phase three-level PWM inverters. Since the three-level inverters have three paths between dc-link and power switches, the reconstructions differ from that in two-level inverters which have two paths there. Considering these paths in three-level inverter, this paper proposes the methods for phase current reconstruction. While the reconstruction method is executed by the currents sampled on the dc-links, the system encounters current-unmeasurable areas where the dc currents cannot be sampled due to the lack of measurement time according to the PWM status. This paper analyzes the areas and proposes a minimum voltage injection method for minimizing them to guarantee accurate current reconstruction. The method provides the expanded operating areas especially in low-output voltage operation and the minimized distortions in output voltages. The feasibility of the proposed method has been assessed in experiments. [ABSTRACT FROM AUTHOR]

Grid interfacing of photovoltaic generators using three-phase inverters offers the advantage of constant power flow allowing smaller capacitance values to be used in the dc-link compared to single-phase inverters. Electrolytic capacitors, used in the dc-link, are often considered to decrease reliability. Reliability could be improved by using film capacitors, but their usage is limited by high cost and low capacitance. Much research has been done to minimize the dc-link capacitance value, particularly, in the field of drives and wind turbines. It has been shown that motor drive in regenerative mode contains a right-half-plane (RHP) pole in its control dynamics having a significant effect on the required dc-link capacitance. The RHP pole can cause instability as has been observed in wind turbine applications. Photovoltaic inverters have been reported to suffer from instability of the dc-link-voltage control, but the origin of the observed problems is poorly understood. This paper shows explicitly that an RHP pole is present in the control dynamics also in photovoltaic inverters affecting the minimum required dc-link capacitance. The paper proposes a minimum value for the dc-link capacitance that is required for stable operation. Design rules are given for single- and two-stage inverters. Moreover, it is shown that a source having constant power output effectively removes the RHP pole from the dc-link-voltage control dynamics. [ABSTRACT FROM AUTHOR]

The digital implementations of Sinusoidal Pulse Width Modulation (SPWM) generators have dominated over their counterparts based on analog circuits. In this paper, an FPGA-based SPWM generator is presented, which is capable to operate at switching frequencies up to 1 MHz (requiring FPGA operation at 100-160 MHz), thus it is capable to support the high switching frequency requirements of modern single-phase dc/ac power converters. The proposed design occupies a small fraction of a medium-sized FPGA and, thus, can be incorporated in larger designs. Additionally, it has a flexible architecture that can be tuned to a variety of single-phase dc/ac inverter applications. The post-layout simulation and experimental results confirm that compared to the past-proposed SPWM generation designs, the SPWM generator presented in this paper exhibits much faster switching frequency, lower power consumption, and higher accuracy of generating the desired SPWM waveform. [ABSTRACT FROM AUTHOR]

An infinite source with series inductance is usually employed as a grid emulator in grid-connected distributed generation systems. Thus, high capacitance of a transmission cable (i.e., underground cable) is too significant to be neglected. As a result, the capacitance and inductance may cause system resonance, which, in turn, challenges system stability. This paper takes offshore wind farm as an example to investigate the resonance issues caused by the submarine transmission cable of the grid-connected generation system. Based on the submarine cable model, a series of considerable resonant peaks is found in the open-loop transfer function of the grid-connected system because of the high-order LC configuration. The resonant peaks are sensitive to the system setup, which is clearly investigated. To overcome the resonances, this paper proposes a cascaded notch-filter-based active damping method to guarantee a good system stability and robustness. Furthermore, the proposed controller employs a proportional-resonant component to reduce the steady-state error of the output current. The simulation and experimental results have validated the findings of resonances and the effectiveness of the proposed controller. [ABSTRACT FROM AUTHOR]

Recent uninterruptible power supply (UPS) systems, in the medium power range (a few 100 kW), are based on a three-power stage topology including a rectifier, an inverter, and a dc-dc converter. The dc-dc converter ensures the charger/discharger function necessary for battery management. The monolithic intercell transformer (ICT) described in this paper is dedicated to such a charger/discharger, of which the nominal power is 137 kW. This dc-dc converter is comprised of eight interleaved cells that are interconnected by the ICT. The first part of this paper briefly presents the full UPS system and the topology of the eight-cell charger/discharger arranged around the eight-phase monolithic ICT. The second part suggests a model and emphasizes the design specificities of the monolithic ICT. The final design is provided by an optimization routine, checked in the end by different 2-D and 3-D finite-element simulations, both electromagnetic and thermal. The third part describes the construction of the ICT prototype. It is then placed in a test bench that reproduces the conditions of future operations and provides current balance conditions. Finally, the experimental results obtained for the 137-kW nominal power validate design parameters and confirm the interest of the ICT solution. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid modulation technique consisting of singe-reference six-pulse-modulation (SRSPM) for front-end dc/dc converter and 33% modulation for three-phase inverter. Employing proposed novel SRSPM to control front-end dc/dc converter, high frequency (HF) pulsating dc voltage waveform is produced, which is equivalent to six-pulse output at 6× line frequency (rectified 6-pulse output of balanced three-phase ac waveforms) once averaged. It reduces the control complexity owing to single-reference three-phase modulation as compared to conventional three-reference three-phase SPWM. In addition, it relives the need of dc-link capacitor reducing the cost and volume. Eliminating dc link capacitor helps in retaining the modulated information at the input of the three-phase inverter. It needs only 33% (one third) modulation of the inverter devices to generate balanced three-phase voltage waveforms resulting in significant saving in (at least 66%) switching losses of inverter semiconductor devices. At any instant of line cycle, only two switches are required to switch at HF and remaining switches retain their unique state of either ON or OFF. Besides, inverter devices are not commutated when the current through them is at its peak value. Drop in switching loss accounts to be around 86.6% in comparison with a standard voltage source inverter (VSI) employing standard three-phase sine pulse width modulation. This paper explains operation and analysis of the HF two-stage inverter modulated by the proposed novel modulation scheme. Analysis has been verified by simulation results using PSIM9.0.4. Experimental results demonstrate effectiveness of the proposed modulation. [ABSTRACT FROM AUTHOR]

Owing to the consistent increase in energy efficiency issues, studies for improving the charging efficiency and energy density of batteries have been receiving attention in the electric vehicle transportation sector. This paper deals with an online electric vehicle (OLEV) system which utilizes the dc power system for reducing loss as well as reducing the size of the required battery capacity. Intensive research on grid integration with OLEV has not been performed until recently and it is necessary to calculate the power flow analysis considering the unique characteristics of OLEV for the commercialization of this new transport system (for the application of this new system in the transport sector). In this paper, the dc OLEV power system is being investigated for reducing line losses and peak power thereby reducing the electric cost levied on the substation. Verification processes are performed through simulation for various scenarios to examine the effectiveness of the proposed system in terms of power consumption, battery state of charge, peak power, and loss reduction. [ABSTRACT FROM AUTHOR]

In this paper, a simple single-phase grid-connected photovoltaic (PV) inverter topology consisting of a boost section, a low-voltage single-phase inverter with an inductive filter, and a step-up transformer interfacing the grid is considered. Ideally, this topology will not inject any lower order harmonics into the grid due to high-frequency pulse width modulation operation. However, the nonideal factors in the system such as core saturation-induced distorted magnetizing current of the transformer and the dead time of the inverter, etc., contribute to a significant amount of lower order harmonics in the grid current. A novel design of inverter current control that mitigates lower order harmonics is presented in this paper. An adaptive harmonic compensation technique and its design are proposed for the lower order harmonic compensation. In addition, a proportional-resonant-integral (PRI) controller and its design are also proposed. This controller eliminates the dc component in the control system, which introduces even harmonics in the grid current in the topology considered. The dynamics of the system due to the interaction between the PRI controller and the adaptive compensation scheme is also analyzed. The complete design has been validated with experimental results and good agreement with theoretical analysis of the overall system is observed. [ABSTRACT FROM AUTHOR]

In this paper, a novel technique to balance the voltage of the two split dc capacitors of a 3-Level neutral-point-clamped inverter using triangular carrier pulse width modulation is presented. This technique, suitable for reactive power compensation and for inverters operating with a relatively low switching frequency, consists in adding a square wave at six times the output frequency. Subsequently, this paper presents a comparison with two already known strategies in which a sinusoidal waveform at two and six times the output frequency are injected. The current contribution to the midpoint of the dc bus is then analyzed for different modulation indexes and operating conditions. Based on this analysis, a small-signal averaged model, suitable for control design purposes is presented. Finally, simulation and experimental results on a 690-Vac, 120-kVA test bench that validate the theory are shown. [ABSTRACT FROM AUTHOR]

This paper presents a method to estimate the inverter lifetime so that we can predict a failure prior to it actually happening. The key contribution of this study is to link the physics of the power devices to a large scale system simulation within a reasonable framework of time. By configuring this technique to a real system, it can be used as a converter design tool or online lifetime estimation tool. In this paper, the presented method is applied to the grid side inverter to show its validity. A power cycling test is designed to gather the lifetime data of a selected insulated gate bipolar transistor (IGBT) module (SKM50GB123D). Die-attach solder fatigue is found out to be the dominant failure mode of this IGBT module under the designed accelerated tests. Furthermore, the crack initiation is found to be highly stress dependent while the crack propagation is almost independent with stress level. Two different damage accumulation methods are used and the estimation results are compared. [ABSTRACT FROM AUTHOR]

Various applications, like in underground mines and oil and gas industries, require remote operation of vector-controlled medium-voltage variable speed drives via a long motor feeder. The use of voltage source inverters in such cases leads to motor overvoltage and harmonic quality problems. The current source inverter (CSI) is ideally matched to these applications because of its motor-friendly voltage output. Speed sensorless operation is mandatory due to the long motor feeder. Although the model reference adaptive system (MRAS) is a powerful and proven speed estimation tool, its implementation in long motor feeder drives faces many challenges. Among them, and addressed in this paper, are inherent dc offset in its stator model, the need for actual motor voltage and current values, and oscillations in the estimated speed due to errors in the motor current measurement signals. In this paper, a sensorless CSI vector-controlled drive, suitable for long motor feeder applications, is studied. Improved speed estimation is achieved by proposing 1) a modified dc-offset eliminator for an MRAS speed estimation and 2) a compensation technique for motor current's measurement errors. Intensive experimental results, for a low-voltage scaled model, along with simulations validate the effectiveness of the proposed technique. [ABSTRACT FROM AUTHOR]

Multilevel inverters with hexagonal and dodecagonal voltage space vector structures have improved harmonic profile compared to two-level inverters. Further improvement in the quality of the waveform is possible using multilevel octadecagonal (18-sided polygon) voltage space vectors. This paper proposes an inverter circuit topology capable of generating multilevel octadecagonal voltage space vectors, by cascading two asymmetric three-level inverters. By the proper selection of dc-link voltages and the resultant switching states for the inverters, voltage space vectors, whose tips lie on three concentric octadecagons, are obtained. The advantages of octadecagonal voltage space vector-based pulsewidth modulation (PWM) techniques are the complete elimination of fifth, seventh, eleventh, and thirteenth harmonics in phase voltages and the extension of linear modulation range. In this paper, a simple PWM timing calculation method is also proposed. Experimental results have been presented in this paper to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

This paper proposes a soft switching technique for dc/ac inverters, by using duty cycle and frequency modulation. Zero voltage switching (ZVS) is achieved through controlling the inductor current bidirectional in every switching cycle. This technique requires no additional resonant components and can be employed for various low power applications on conventional full-bridge and half-bridge inverter topologies. Three different current mode control schemes are derived from the basic theory of the proposed technique. They are referred to as boundary current mode (BCM), variable hysteresis current mode (VHCM), and constant hysteresis current mode (CHCM) in this paper and their advantages and disadvantages are compared. Simulation and experimental results demonstrate the feasibilities of the proposed soft-switching technique and its control schemes. [ABSTRACT FROM PUBLISHER]

This paper investigates the suitability of selective harmonic elimination (SHE) for low-loss multimegawatt grid-connected photovoltaic (PV) inverters. The proposed system is able to meet utilities regulations, IEEE and IEC standards. In an attempt to substantiate the potential superiority of SHE over carrier-based or space-vector pulsewidth modulation (PWM), this paper demonstrates that SHE may allow grid-connected PV inverters to be controlled using a switching frequency of less than 1 kHz, while the inverter is still able to provide necessary operation features such as independent control of active and reactive powers and operation control simplicity. For system validation, experimental results with SHE are compared to the case when the inverter is controlled using third-harmonic injection PWM, with a 2-kHz switching frequency. Furthermore, the paper proposes a new implementation technique for SHE that utilizes the third harmonics to spread the switching angles over 90° instead of being located in a narrow range as generated when using conventional techniques, along with increases in modulation index. The advantages of the proposed technique include simplicity in implementation and flexibility in PWM waveforms. Simulation and experimentation demonstrate agreement, which validates the practicability of the proposed system. [ABSTRACT FROM AUTHOR]

In this paper, a new control strategy for improving weighted efficiency in photovoltaic (PV) ac module-type interleaved flyback inverters (ILFIs) is proposed. The efficiency of the ILFI for PV ac modules has to be high, not only for the maximum power, but also for other power levels according to weather conditions. For PV power conversion efficiency improvement in all load ranges, a new control method for an ILFI according to the output of the PV module is proposed in this paper. The proposed method controls an active clamp circuit and each converter phase of an ILFI according to the output power of the PV module. Thus, the efficiency of an ILFI as a PV power conditioner can be improved in all power range of the PV module. Theoretical analysis, simulation, and experiment are performed in order to verify the proposed control method. [ABSTRACT FROM AUTHOR]

In order to maximize the profitability of big photovoltaic (PV) plants, high-power PV inverters of more than 500 kW are becoming attractive. The master–slave (MS) inverter is one of the most interesting architectures. Usually, it is composed of N-paralleled three-phase inverters connected to the medium voltage grid through a transformer with N secondaries on the low-voltage side. This type of transformer is up to 40% more expensive than a single secondary one. This paper analyses the case in which the N inverters are connected to a single secondary transformer so that the N inverters share the ac and dc sides. Furthermore, three-phase three-limb inductors are used, which are around 25% cheaper than single-phase equivalents. Although the use of this type of transformer and inductors is highly attractive in economic terms, it does generate two types of couplings between the different inverters, compromising the system stability. This paper presents a new control technique that achieves a stable system, invariant with N, and independent of the type of inductors and transformer used. Stability of the system is guaranteed in any situation and it can be implemented with a low computational cost. The simulations and the practical results obtained with an Ingecon Sun 625HE-MS confirm the correct functioning of this control technique. [ABSTRACT FROM AUTHOR]

This paper presents investigations on current ripple in a dual 2-level inverter feeding an open-end winding induction motor drive. Pulsewidth modulations (PWMs) for the independently controlled inverters are implemented using a simple effective time placement affected by offset-time concept, thus, eliminating the use of sector identification and lookup tables. Analytical expressions for ripple content in the motor phase current are developed and a current trajectory is theoretically obtained directly from the switching states of the dual inverter in a stationary reference frame. In addition, this paper also describes a current ripple trajectory in the motor by exploring the freedom of independently operating the individual inverters with different PWMs. Based on the analysis, discontinuous PWMs are employed for the individually inverters that not only offer the advantage of reducing the total switching commutations in the inverters but also reduces the current ripple. Analytical expression for the RMS ripple current and variation in RMS ripple current in one cycle of operation for different PWMs are also presented for the entire speed range of the dual-inverter drive. The performance of the dual-inverter drive with the proposed PWM variants is first studied analytically and then verified by performing suitable experiments on a 1-kW open-end winding induction motor drive. [ABSTRACT FROM AUTHOR]

Switched boost inverter (SBI) is a single-stage power converter derived from Inverse Watkins Johnson topology. Unlike the traditional buck-type voltage source inverter (VSI), the SBI can produce an ac output voltage that is either greater or less than the available dc input voltage. Also, the SBI exhibits better electromagnetic interference noise immunity when compared to the VSI, which enables compact design of the power converter. Another advantage of SBI is that it can supply both dc and ac loads simultaneously from a single dc input. These features make the SBI suitable for dc nanogrid applications. In this paper, the SBI is proposed as a power electronic interface in dc nanogrid. The structure and advantages of the proposed SBI-based nanogrid are discussed in detail. This paper also presents a dq synchronous-reference-frame-based controller for SBI, which regulates both dc and ac bus voltages of the nanogrid to their respective reference values under steady state as well as under dynamic load variation in the nanogrid. The control system of SBI has been experimentally validated using a 0.5-kW laboratory prototype of the SBI supplying both dc and ac loads simultaneously, and the relevant experimental results are given in this paper. The low cross regulation and the dynamic performance of the control system have also been verified experimentally for a 20% step change in either dc or ac load of SBI. These experimental results confirm the suitability of the SBI and its closed-loop control strategy for dc nanogrid applications. [ABSTRACT FROM AUTHOR]

This paper presents a quick and accurate power control method for a zone-control induction heating (ZCIH) system consisting of multiple working coils connected to multiple H-bridge inverters. A uniform temperature profile can be achieved by adjusting the current in each working coil. This paper proposes a new current control method based on a circuit model using real and imaginary (Re–Im) current/voltage components. The method detects and controls the Re–Im components of the coil current instead of the current amplitude and phase angle. As a result, the proposed method enables the inverters to control the coil current independently from the others. Experiments using a six-coil ZCIH system are conducted to verify the validity of the proposed method. The experimental results confirmed that the proposed method makes it possible to improve the stability of the current feedback control, not only in steady states but also in transient states. [ABSTRACT FROM AUTHOR]

Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation and experimental results for validating various performance aspects of the proposed control schemes can be found in a later section of this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a model of the mutual impedance between ring-type coils used in domestic induction hobs. Recent developments in these appliances have focused on flexible cooking surfaces, including adjustable-size or total-active surfaces. Flexible cooking surfaces are implemented by means of several small ring-type closely arranged coils, each one supplied by a resonant inverter. The basic winding is a ring-type circular small coil, whose self-impedance has been reported previously. In this paper, the coupling between coils in terms of impedance is derived. The coils are modeled as axisymmetric current density distributions with parallel revolution axes. The mutual impedance between the coils is obtained considering two media representing the load and the ferrite, respectively. Experimental measurements have been performed to validate the results. [ABSTRACT FROM AUTHOR]

This paper is concerned with the design and control of a three-phase voltage source grid-connected interleaved inverter. This topology enables the use of low-current devices capable of switching at high frequency, which together with the ripple cancelation feature reduces the size of the output filter and the inverter considerably compared to an equivalent classical two-level voltage source inverter with an LCL output filter using high-current devices with considerably lower switching frequency. Due to its higher switching frequency and low-filter component values, the interleaved inverter also has a much higher bandwidth than the classical inverter, which improves grid voltage harmonics disturbance rejection and increases the speed of response of the inverter and its capability to ride through grid disturbance (e.g., voltage sags and swells). The paper discusses the selection of the number of channels and the filter component values of the interleaved inverter. The design of the digital control system is then discussed in detail. Simulation and practical results are presented to validate the design and demonstrate its capabilities. [ABSTRACT FROM AUTHOR]

This paper focuses on the common dc-link voltage between a three-phase diode rectifier and a modular multilevel cascade inverter based on double-star chopper cells (MMCI-DSCC) for a medium-voltage motor drive. This motor drive can be operated even when no capacitor exists on the dc link. However, a nonnegligible, but predictable, amount of switching-ripple voltage occurs on the dc link. This paper achieves modeling and analysis of the switching-ripple voltage, thus making it possible to design a small-sized dc passive filter consisting of series connection of a film capacitor and a damping resistor. A 400-V, 15-kW down scaled system is used to confirm the effectiveness of the analysis and the dc filter. Experimental results show that the switching-ripple voltage can be attenuated satisfactorily by the dc filter, and that the power loss dissipated in the damping resistor is negligible, compared to the rated power of 15 kW. [ABSTRACT FROM AUTHOR]

This paper addresses the resonance problem in a parallel-inverter-based grid-interactive microgrid. Unlike the single grid-connected inverter system where the resonance frequency is mainly fixed by the inverter output LCL filter parameters, the parallel-inverter-based grid-interactive microgrid system presents a more challenging picture where inverter interactions will excite complex resonances at various frequencies. As a result, line currents of inverters can be severely distorted even when the control schemes and filter circuits are properly designed based on the single-inverter model. This paper first develops a microgrid model using discrete time-domain closed-loop Norton's equivalent circuit. Multiple resonances can then be evaluated with the developed model. To improve the microgrid power quality, this paper also designs a virtual-harmonic-resistance-based active damping method. The proposed damping method can be seamlessly incorporated into the conventional deadbeat control scheme through the direct control reference modification. Therefore, the active damping method is able to address both the transient and steady-state resonances within the deadbeat current control bandwidth. Simulation and experimental results are provided to validate the correctness of the developed resonance modeling and active damping methods. [ABSTRACT FROM AUTHOR]

In this paper, based on Cuk converter, a novel commutation torque ripple reduction strategy is proposed for the brushless DC motor. Output modes (buck–boost mode and boost mode) of the Cuk converter during the commutation period and normal conduction period are altered by designing a mode selection circuit, which can reduce commutation torque ripple over the entire speed range. During the commutation period, Cuk converter operates in the boost mode to step up the input voltage of three-phase bridge inverter and then meet the voltage demand of commutation period, such that the commutation torque ripple can be reduced by keeping the noncommutated current steady. In order to improve the utilization rate of the converter, during the normal conduction period, Cuk converter operates in the buck–boost mode and the input voltage of three-phase bridge inverter is regulated by adopting the pulse amplitude modulation (PAM) method without the inverter pulse width modulation chopping, which can reduce the voltage spike damage to the motor windings caused by turn-on/off of MOSFET in the inverter and simplify the program of modulation method further. The experimental results verify the correctness of the theory and the effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]

Multilevel inverters are receiving more attentions nowadays as one of preferred solutions for medium- and high-power applications. As one of the most popular hybrid multilevel inverter topologies, the five-level active-neutral-point-clamped inverter (5L-ANPC) combines the features of the conventional flying-capacitor type and neutral-point-clamped (NPC) type inverter and was commercially used for industrial applications. In order to further decrease the number of active switches, this paper proposes a seven-switch 5L-ANPC (7S-5L-ANPC) topology, which employs only seven active switches and two discrete diodes. The analysis has shown a lower current rating can be selected for the seventh switch under high power factor condition, which is verified by simulation results. The modulation strategy for 7S-5L-ANPC inverter is discussed. A 1 kVA single-phase experimental prototype is built to verify the validity and flexibility of the proposed topology and modulation method. [ABSTRACT FROM AUTHOR]

Transformerless topologies are employed in single-phase photovoltaic inverter converters due to their small size and low weight. Avoiding the grid-side transformer requires the modulation technique and the basis topology to be accordingly changed in order to mitigate dc current components in the grid side and the leakage current to ground. This paper carries out a sensitivity analysis of the selected transformerless topologies. This analysis investigates the impact of parameter variations depending on the choice of the employed semiconductor devices and detects the device for each topology, which affects the overall efficiency the most as well as the topology that is affected the most by the parameter variations with respect to the efficiency, leakage current, and grid-side dc current component. It is shown that, based on the proposed statistical analysis procedure, the impact of parameter variability can be analyzed with a reduced computational burden. An approach for the simplification of the comparison of the analyzed topologies is presented. As a result, relevant information for engineers selecting the most suitable power devices for the implementation of a certain transformerless topology is provided. The proposed analysis also allows to assess the robustness of the topologies’ performance to the choice of different components when this selections is driven by other factors, such as cost and supply chain management. [ABSTRACT FROM AUTHOR]

In order to meet the high performance and efficiency requirements, a new space vector-based discontinuous modulation strategy for neutral-point clamped three-level inverter is presented in this paper. Different from the conventional discontinuous PWM (DPWM) strategies, a new clamping state is applied to synthesize the reference voltage under the condition of low modulation index. The rms value of output current ripple for different clamping states are calculated, and then the distribution of the new clamping state and the other two clamping states adopted in conventional DPWMs is optimized based on the calculation results. The switching sequences are redesigned according to the new distribution of the three clamping states. The output voltage and current, switching loss, neutral-point voltage ripple and the common mode voltage of the proposed DPWM strategy and DPWM0–DPWM3 are compared by simulation and experimental results. The results show that by the use of the proposed strategy, the values of total demand distortion of output current (ITDD) and weighted total harmonic distortion of output voltage (\boldsymbolV{\mathbf{WTHD}}) are the lowest. Furthermore, the product of switching loss and ITDD of the proposed strategy maintains the lowest within a large range of modulation index-load angle plane. It can be concluded that the utilization of the new clamping state and optimal distribution of different clamping states could enhance the output performance of the inverter. Moreover, the high-efficiency requirement can also be realized at the same time. [ABSTRACT FROM AUTHOR]

This paper presents a direct model predictive current control (MPC) strategy for quasi-Z-source inverters (qZSIs). A discrete-time model is derived that accurately captures all operating modes of the converter. Both sides of the qZSI are controlled simultaneously based on the inductor current and capacitor voltage on the dc side as well as the output current on the ac side. To improve the closed-loop performance of the converter, a long prediction horizon is implemented. However, the underlying optimization problem may become computationally intractable because of the substantial increase in the computational power demands, which in turn would prevent the implementation of the control strategy in real time. To overcome this and to solve the problem in a computationally efficient manner, a branch-and-bound strategy is used along with a move blocking scheme. Simulation and experimental results are provided to verify the effectiveness of the presented control strategy. [ABSTRACT FROM AUTHOR]