Search

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid seven-level converter based on T-type converter and H-bridge cascaded suitable for low-voltage and high-power-density applications. The operation principles and conduction paths are analyzed comprehensively. Voltage balance control of the floating capacitors is the key point of this paper. Mathematical expressions of capacitor voltage balance conditions are deduced based on sinusoidal pulse width modulation (SPWM). The results show that floating capacitor voltages are only balanced when the modulation index is below 0.82 under SPWM. In order to enlarge the modulation index ensuring the capacitor voltage balance, space vector modulation (SVM) is also applied to regulate floating capacitor voltages taking advantage of redundant switching vectors. Meanwhile, in SVM, there are no additional control requirements for the capacitor voltage. Taken both SPWM and SVM into consideration, the limit to the range of operation for this seven-level converter is presented, which is a function of the modulation index and the power factor. The merit of dc voltage utilization improvement in this topology is also analyzed based on simulation results. Simulations and experimental results under different modulation index and RL load are presented to verify the modulation strategies illustrated in this paper. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel five-level nested neutral point piloted (NNPP) converter and analyzes the operating principle of five-level NNPP converter. This paper presents a novel space vector pulse width modulation (SVPWM) algorithm based on gh coordinate for five-level NNPP converter. First, the common-mode voltage is reduced by choosing the appropriate redundant switching states. After that, the floating-capacitor voltage balance control strategy is presented. The appropriate switch combinations of each phase are determined by the control requirements of floating-capacitor voltages respectively and the hardware mapping method of the switching states is presented. Furthermore, the neutral-point voltage balance control strategy is presented. In order to balance the dc-link capacitor voltages, the seven-segment switching sequence is selected according to the control requirements of dc-link capacitor voltages and the neutral-point voltage regulatory factor is introduced to regulate the durations of the redundant switching states in a switching cycle. Finally, the validity of the novel SVPWM algorithm with decoupling control strategies of floating-capacitor voltages and dc-link capacitor voltages is verified by the experimental results of five-level NNPP converter under steady-state and dynamic conditions. [ABSTRACT FROM AUTHOR]

This paper presents new space vector pulsewidth modulation (PWM) strategies for a single-phase three-level buck-boost neutral point clamped inverter coupled with impedance-source (IS) network. These strategies can be implemented for systems with any IS network with neutral point. The case study system is based on the quasi-Z-source inverter with continuous input current. To demonstrate an improved performance, the strategies are compared with a traditional PWM strategy. The advantages lie in reduced switching number, without output voltage quality distortion. The simulation and experimental results confirm the theoretical predictions. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems containing a rechargeable battery as an energy buffer require multiple dc–dc converters for PV panel control and battery regulation, and hence, they are prone to be complex and costly. To simplify the system by reducing the number of converters, this paper proposes the nonisolated switched capacitor converter (SCC)-based multiport converter (SC-MPC) for standalone PV systems. The proposed SC-MPC can be derived by integrating a bidirectional pulsewidth modulation (PWM) converter, series-resonant converter (SRC), and an SCC with sharing switches. PWM and pulse frequency modulation (PFM) controls are employed for the PWM converter and SRC, respectively, to regulate either a battery voltage, output voltage, or input power from a PV panel, depending on power balance among the input, battery, and load. The 150-W prototype was built for an experimental verification, and the results demonstrated the output voltage could be regulated independently on the battery voltage or input port of PV panels. [ABSTRACT FROM AUTHOR]

In this paper, a novel space-vector pulsewidth modulation technique for a five-level active neutral-point clamped (5L-ANPC) inverter is proposed to eliminate the common-mode voltage (CMV). For the 5L-ANPC inverter, which produces a good output voltage performance and lowdv/dt, the total 125 voltage vectors can be generated, among which the proposed scheme employs only 19 voltage vectors producing a zero CMV. Due to the limitation of voltage vectors selected, the dc-link capacitor voltages of the 5L-ANPC inverter cannot be balanced by themselves. Therefore, the capacitor voltages of the inverter should be controlled by choosing the redundant switching states appropriately. The validity of the proposed modulation scheme has been verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

The switching frequency is an important control parameter of pulse-width-modulation (PWM) rectifier to reduce switching losses and electromagnetic interference noise. This paper proposed a variable switching frequency PWM (VSFPWM) strategy for dc-link voltage ripple control in two-level rectifier. DC-link voltage ripple is determined by the dc-link current directly, and can be predicted synchronously with PWM signals. A real-time prediction model of dc-link voltage ripple is derived for a common voltage-oriented control PWM rectifier. Then, VSFPWM control is introduced, which changes the switching frequency cycle to cycle with a restriction of dc-link voltage ripple peak value. Furthermore, the dynamic behavior is also observed when the proposed VSFPWM control scheme is adopted. Detail simulation and experimental comparisons are carried out between VSFPWM and normal constant switching frequency PWM, which demonstrate the advantages of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the active capacitor voltage-balancing (ACVB) methods based on the dynamic model for a five-level nested neutral-point piloted (NNPP) converter using hybrid carrier modulation. The traditional hybrid carrier modulation provides natural voltage balancing of floating capacitors and dc-link capacitors. First, the natural voltage-balancing ability under steady-state and ideal conditions is theoretically proved. However, there are accumulated errors and deviations of capacitor voltages in practical applications, especially under dynamic conditions. In order to address the accumulated errors and deviations of capacitor voltages, the dynamic models of floating-capacitor voltages and neutral-point voltage are established. Moreover, the ACVB method based on the dynamic model of the neutral-point voltage is proposed by injecting the zero-sequence voltage. And the ACVB method based on the dynamic model of floating-capacitor voltages is proposed by introducing the adjustment variables. The proposed ACVB methods have the advantages of simple formula, definite physical meaning, and high accuracy. Furthermore, the output voltage quality and current quality are evaluated in term of total harmonic distortion and the effect of model parameter mismatch on the proposed ACVB methods is presented. Finally, the comparative simulation and experimental results verify the correctness of the proposed ACVB methods based on the dynamic model under different conditions. [ABSTRACT FROM AUTHOR]

In order to solve the neutral-point voltage unbalancing problem for three-level inverters, this paper proposes a method to balance the neutral-point voltage for three-level inverters with variable modulation wave offset sinusoidal pulse-width modulation (SPWM) control. Based on the mathematical expressions of neutral-point voltage unbalancing, the factors are studied, which affect the fluctuation of neutral-point voltage. Theoretically the mathematical expressions of the neutral-point voltage with the proposed method are derived, and the mathematical relationship between the fluctuation of neutral-point voltage and the adjusting offset of modulation wave is studied. This proposed method realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the modulation wave based on SPWM (DCOSPWM). This DCOSPWM method is very simple, which has good steady-state performance and is easy for digital implementation. The simulation results verify the correctness of the theoretical analysis in this paper, and the feasibility and effectiveness of this method is verified by the experiments in the experimental platform of neutral point clamped three-level inverters based on digital signal processor (DSP)-complex programmable logic device (CPLD). [ABSTRACT FROM AUTHOR]

This paper presents a general space vector modulation (SVM) method for the modular multilevel converter (MMC). Compared with earlier modulation methods, the proposed SVM method not only utilizes the maximum level number (i.e., $2n+ 1$, where $n$ is the number of submodules in the upper or lower arm of each phase) of output phase voltages, but also leads to an optimized control performance in terms of capacitor voltage balancing, circulating current suppression, and common-mode voltage reduction. The maximum level number is achieved by introducing a new equivalent circuit of the MMC, and the optimized control is obtained by selecting the optimal redundant switching states. Since the computational burden of the SVM scheme is independent of the voltage level number, the proposed method is well suited to the MMC with any number of submodules. Simulation and experimental results are presented to validate the proposed method. [ABSTRACT FROM PUBLISHER]

The flying-capacitor modular multilevel converter (FC-MMC) overcomes the low/zero-speed operation issues of conventional MMC-based drive. The FC-MMC injects no common-mode voltage (CMV) to the drive system. However, the pulse width modulator (PWM) introduces switching ripples, which appear as CMV on motor stator windings. To completely get rid of the CMV, an elimination method based on a new modulation scheme is proposed in this paper. The modulation algorithm places the switching pulses end to end for upper and lower arms, respectively. The consistent switching positions between upper and lower arms lead to the complete CMV elimination for FC-MMC-based drive system in entire speed range. Although the proposed method slightly increases the switching frequency as compared to conventional phase-shifted PWM, it is still acceptable in medium-voltage applications. The validation of the proposal is proved by simulations and experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes a pulse width modulation plus phase-shift (PPS) control for nonisolated high gain soft-switching bidirectional dc–dc converter (HSBDC). The phase-shift angle is used to control the direction and amount of power flow of the bidirectional dc–dc converter, while the duty cycle is used to balance the voltage between two high voltage side (HVS) capacitors. The HSBDC with PPS control has the advantages of simple control structure and symmetrical switching patterns, ensured soft-switching in both forward and backward modes at all load under wide voltage range, and reduced voltage ratings of the HVS capacitors and switches. The operation principle of the HSBDC with PPS control is analyzed in detail. Based on the analysis the passive component is designed to achieve higher efficiency. A 3-kW prototype is implemented and tested to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

The noninverting buck–boost converter has attracted significant attention in the photovoltaic (PV) module integrated application, as it offers high efficiency while maintaining a low cost and a simple topology. When this converter is employed, special care must be taken at the transition between buck and boost operating modes, as a dead-zone in the voltage transfer function can cause abrupt perturbations in the controlled voltage, decreasing the regulation quality and ultimately lowering the power conversion efficiency. In this paper, a new dead-zone compensation technique is proposed with the scope of smoothing the transition between operating modes, eliminating the voltage ripple and improving the regulation performance, while maintaining high efficiency. The converter under analysis is studied together with its gate driving circuit, which is based on a bootstrap capacitor power supply for the high-side switches. The proposed dead-zone compensation technique is deduced by using the principle of maintaining the ideal voltage gain function across the converter operating range. The technique is analyzed, implemented and tested on a purposely built PV module integrated noninverting buck–boost converter. The experiments reveal a sensible improvement of the voltage regulation during mode transition, confirming the effectiveness of the proposed technique and its fitness for the PV application. [ABSTRACT FROM AUTHOR]

Five-level hybrid-clamped (5L-HC) converter is a newly proposed topology which is suitable for high-performance medium-voltage high-power conversions without switches directly connected in series. The critical issue of this converter is that two flying capacitor voltages of each phase and two neutral-point potentials of the dc-link need to be balanced. This paper presents a decoupled voltage balancing method for this 5L-HC converter based on modified phase-shifted pulse width modulation (PS-PWM) and optimal zero-sequence voltage injection. The voltages across the central dc-link capacitor and two flying capacitors are balanced first by adjusting the width of four PWM signals. Second, the relationship between the neutral-point currents and the output phase voltage is studied and the upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection. Both steady-state and dynamic-state simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

Presently, the neutral-point potential offset is an inherent problem for three-level converters on three-phase four-wire active power filters. The conventional three-dimensional space vector pulse width modulation (3-D-SVPWM) strategy is adopted as a normal solution to the problem, but the selection of space vector sectors for four-wire converter is both abstract and complicated in practice. This paper proposes a new PWM strategy accordingly to simplify the selection process and the calculation of duration. Compared to the conventional 3D-SVPWM, the proposed method locates the sector of optimal vector directly with the polarity of three-phase reference voltage. Then, by applying voltage–second balance rule, it can perform a fast calculation of the duration and generate PWM signals to control the switching devices’ on/off. As an approach to correct the imbalance dc-link capacitor voltage, this strategy reconstructs the switching sequence. A portion of state O duration is disassembled into states P and N to suppress the neutral-point potential offset. The proposed strategy is validated with a range of experiments. The results indicate that this simplified PWM strategy can effectively reduce the computational burden, and also the dc-link capacitor voltage is well controlled. [ABSTRACT FROM PUBLISHER]

Four-level nested neutral-point clamped (NNPC) inverters experience severe voltage balancing problems under low output-frequency conditions when the conventional four-level space vector modulation (4L-SVM) technique is applied, which limits their wider application. In order to get a complete control of the flying-capacitor voltages, and to alleviate the calculation burden of conventional 4L-SVM, a simplified but effective 4L-SVM technique along with the voltage balance control (VBC) function is proposed in this paper. For low modulation indexes, zero and small vectors are selectively utilized and distributed to force the average charging and discharging time of flying capacitors to be equal to each other during every switching period, so that voltage ripples are greatly reduced to be within an acceptable level under low output-frequency conditions. For high modulation indexes, the simplification of conventional 4L-SVM for NNPC inverters into two-level SVM is proposed to reduce the computation complexity. Principles of the proposed 4L-SVM and VBC are elaborated in detail. The steady-state, transient-state, and VBC performances are investigated and compared with the case where the conventional 4L-SVM is applied. Simulation results of a 5 MVA inverter system and experimental results of a scaled-down 5 kVA inverter system are presented to validate the proposed method. [ABSTRACT FROM PUBLISHER]

The current imbalance among the two input capacitors is one of the important issues of the half-bridge three-level (HBTL) dc/dc converter, which would affect system performance and reliability. In this paper, a zero-voltage switching (ZVS) pulse-wide modulation (PWM) strategy including two operation modes is proposed. Based on the proposed ZVS PWM strategy, a capacitor current-balancing control is proposed for the HBTL dc/dc converter, where the currents on the two input capacitors can be kept balanced by alternating the two operation modes of the proposed ZVS PWM strategy. Therefore, the proposed control strategy can improve the performance and reliability of the converter in the aspect of balancing the thermal stresses and lifetimes among the two input capacitors. Finally, simulation and experimental studies are conducted and results verify the proposed control strategy. [ABSTRACT FROM PUBLISHER]

Z-source inverter provides a competitive single-stage dc–ac power conversion with the capability of both buck and boost voltage regulation. In order to maximize voltage gain and to increase efficiency, this paper proposes an improved pulse-width modulation (PWM) strategy. By adjusting the shoot-through duty ratio of one-phase leg, it regulates the average value of intermediate dc-link voltage, which is the same as the instantaneous maximum of three-phase line voltage in one switching time period (Ts) . And the other two-phase legs maintain the fixed switching states. Thus, the equivalent switching frequency of power devices in the inverter bridge is reduced to 1/ 3fs (fs is the frequency corresponding to Ts). The operating principles and closed-loop controller design are analyzed and verified by simulation and experiments. Compared with the existing PWM strategies, the improved PWM (IPWM) strategy demonstrates higher efficiency under full operation range of low voltage gain (1.27-2) application. However, with the IPWM strategy, the inductor current and capacitor voltage contain six-time-line-frequency ripples, which consequently require large size of the passive components when the output frequency is very low. Thus, it is also suitable for 400–800-Hz medium frequency aircraft and vessel power supply system due to a relatively high output line frequency. Furthermore, the idea of IPWM strategy can be extended to other kinds of three-phase impedance network-based inverters. [ABSTRACT FROM PUBLISHER]

Dynamic voltage restorer (DVR) technology has become a mature power quality product. In high-power applications, DVR using a multilevel converter is commonly used. However, DVR using a multilevel direct pulse width modulation (PWM) ac–ac converter has not been well studied. This paper presents a new DVR topology using a cascaded multilevel direct PWM ac–ac converter. In the proposed scheme, the unit cell of the multilevel converter consists of a single-phase PWM ac-ac converter using switching cell structure with coupled inductors. Therefore, the multilevel converter can be short- and open-circuited without damaging the switching devices. Neither lossy RC snubber nor a dedicated soft commutation strategy is required in the proposed DVR. This improves the reliability of the DVR system. The output voltage levels of the multilevel converter increase with the number of cascaded unit cells, and a high ac output voltage is obtained by using low-voltage-rating switching devices. Furthermore, a phase-shifted PWM technique is applied to significantly reduce the size of the output filter inductor. A 1-kW prototype of single-phase DVR is developed, and its performance is experimentally verified. Finally, the simulation results are shown for a three-phase DVR system. [ABSTRACT FROM AUTHOR]

In signal injection sensorless drives, the injection voltage cannot be reduced under a certain value. The lower limit of the injection voltage is mainly enforced by the inverter nonlinearity that causes distortion of the injection voltage and degradation of the position estimation performance. After analyzing the inverter nonlinearity during the voltage injection, it is revealed that parasitic capacitances of insulated-gate bipolar transistors have positive effects on inverter output linearity and sensorless control. Based on this analysis, this paper proposes a method to reduce the injection voltage by connecting additional capacitors to the output terminals of the inverter. Simulation and experimental results are provided to verify the effectiveness of the proposed idea. In the experiments, using the capacitor-integrated inverter, it is shown that the injection voltage can be reduced by more than half without degrading the position estimation performance. [ABSTRACT FROM AUTHOR]

The imbalance in the currents of strings of LEDs will cause fast degradation or even failure in some LEDs. Such current imbalance should be avoided. To balance the common average current, a small duty cycle may necessitate a large LED turn-on current amplitude, which may cause temporal overheat and low luminous efficacy of the LEDs. This paper presents a current balancing method based on pulse-width modulation of a common bus voltage to each LED string to achieve the intended average current. An optimal feedback control scheme is proposed to maximize the duty cycles and minimize the bus voltage. As a result, at least one of the LED strings is operating at unity duty cycle. The analysis, implementation, and verification are detailed in this paper. [ABSTRACT FROM AUTHOR]

The five-level active neutral-point-clamped (5L-ANPC) converter has been widely studied for its excellent performance in high-power medium-voltage applications. This paper analyzes the space vector pulse width modulation (SVPWM) strategy of the 5L-ANPC converter in the virtual coordinate, and presents an optimized control strategy which can balance the neutral point (NP) voltage and avoid the dead-time effects for the first time. In this strategy, on one hand, the 125 space vectors are combined by 96 triangles in the seven-segment vector synthesis method, then the triangles are divided into seven categories which have different characteristics of balancing the NP voltage, and every category has its own principles to choose the vector sequence and compute the vector durations. On the other hand, the dead-time effects of the 5L-ANPC converter are studied in detail and the transitions between different switching states are constrained in the optimized control strategy to avoid the dead-time effects that cannot be compensated by traditional pulse-based dead-time compensation methods. Finally, the optimized SVPWM strategy is experimentally verified in this paper. [ABSTRACT FROM AUTHOR]

This paper presents the high-performance quasi-Z-source series resonant dc–dc converter as a candidate topology for the photovoltaic module-level power electronics applications. The converter features a wide input voltage and load regulation range thanks to the multimode operation, i.e., when the shoot-through pulse width modulation and phase-shift modulation are combined in a single switching stage to realize the boost and buck operating modes, respectively. Our experiments confirmed that the proposed converter is capable of ensuring ripple-free 400 V output voltage within the sixfold variation of the input voltage (from 10 to 60 V). The converter prototype assembled achieved a maximum efficiency of 97.4%, which includes the auxiliary power and control system losses. [ABSTRACT FROM AUTHOR]

Diode-assisted buck–boost voltage-source inverter achieves high voltage gain by introducing a switch-capacitor based high step-up dc–dc circuit between the dc source and inverter bridge. As for the unique structure, various pulse width modulation (PWM) strategies are developed with regard to the chopped intermediate dc-link voltage. In order to maximize voltage gain and increase efficiency, this paper proposes a novel PWM strategy. It regulates the average value of intermediate dc-link voltage in one switching time period ( Ts) the same as the instantaneous maximum value of three-phase line voltage by controlling the front boost circuit. Then, the equivalent switching frequency of power devices in the inverter bridge can be reduced to 1/3fs (fs = 1/Ts). The operating principle and closed-loop controller design are analyzed and verified by simulations and experiments. Compared with existing PWM strategies, the new control strategy demonstrates less power device requirement and higher efficiency in high voltage gain applications. It is a more competitive topology for wide range dc/ac voltage regulation in renewable energy applications. Furthermore, with new control strategy, the dc-side inductor current and capacitor voltage contains six-time line-frequency ripples. To overcome the undesired influence of low frequency ripples, it is also suitable for 400–800 Hz medium frequency aircraft and vessel power supply system. [ABSTRACT FROM PUBLISHER]

Four-level hybrid-clamped (4L-HC) inverter is a newly proposed topology which is suitable for high-performance medium-voltage drives. Each phase of this topology consists of eight switches and a flying capacitor and the dc-link is split into three parts by two neutral points. In order to ensure the topology operating properly, the voltages across the flying capacitors and three dc-link capacitors should be controlled and maintain balanced at their nominal values. This paper presents a decoupled voltage balancing method for this 4L-HC inverter, including the voltage balancing of dc-link capacitors and flying capacitors. A modified phase-shifted pulse-width modulation method is used to regulate the voltages of flying capacitors and the central dc-link capacitor. The relationship between the neutral-point currents and the output voltage is studied and the upper and lower dc-link capacitor voltages are balanced by injecting an optimum zero-sequence voltage. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

This paper proposes a new circuit topology for a multilevel pulse width modulation (PWM) rectifier. The proposed method forms a new circuit by combining a diode clamp-type topology with a flying capacitor-type topology. The proposed circuit uses only 12 switches, despite the use of a five-level three-phase PWM rectifier. Further, the proposed circuit can obtain good performance, same as a conventional multilevel circuit. This paper describes about the features of the proposed topology; the control strategy and the loss analysis that is estimated by a circuit simulator. In addition, the basic operation of the proposed method is confirmed by simulation and experimental results. The proposed converter achieved total harmonic distortion of 3.4% for the input current and efficiency of 97.4% for a 1 kW class experimental setup. [ABSTRACT FROM AUTHOR]

This paper presents a voltage regulator topology, implemented using low-voltage devices, for converting high input voltage (>4.5 V) to low output voltages with fine-grain control (0.3 to 1 V). The topology merges a Dickson's switched-capacitor stage with a current-mode inductive buck stage, and optimizes the frequency of operations to reduce the overall passive size. The proposed two-stage hybrid regulator, designed in 130-nm standard digital process, operates from 4.8 to 6 V at input and regulates output voltage as low as 0.3 V with a maximum output power of 90 mW and a peak efficiency of 69%. [ABSTRACT FROM PUBLISHER]

This paper proposes a new five-level voltage source inverter for medium-voltage high-power applications. The proposed inverter is based on the upgrade of a four-level nested neutral-point clamped converter. This inverter can operate over a wide range of voltages without the need for connecting power semiconductor in series, has high-quality output voltage and fewer components compared to other classic five-level topologies. The features and operation of the proposed converter are studied and a simple sinusoidal PWM scheme is developed to control and balance the flying capacitors to their desired values. The performance of the proposed converter is evaluated by simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes and evaluates an active voltage-balancing method for stacked multicell converters (SMCs) using phase-shifted pulse width modulation. The method is easy to implement and can be applied to SMCs with any number of levels. The proposed method balances the voltages of the capacitors by modifying the duty cycle of each switch of the SMC using a proportional controller. The direction of the output current and the crossed effect among the duty cycles of the switches is considered and used to improve capacitor voltage balance. The performance of the proposed voltage-balancing method is verified experimentally for different loads, such as linear and nonlinear loads, and under transient conditions. [ABSTRACT FROM PUBLISHER]

A capacitor voltage-balancing method for a nested neutral point clamped (NNPC) inverter is proposed in this paper. The NNPC inverter is a newly developed four-level voltage-source inverter for medium-voltage applications with properties such as operating over a wide range of voltages (2.4–7.2 kV) without the need for connecting power semiconductor in series and high-quality output voltage. The NNPC topology has two flying capacitors in each leg. In order to ensure that the inverter can operate normally and all switching devices share identical voltage stress, the voltage across each capacitor should be controlled and maintained at one-third of dc bus voltage. The proposed capacitor voltage-balancing method takes advantage of redundancy in phase switching states to control and balance flying capacitor voltages. Simple and effective logic tables are developed for the balancing control. The proposed method is easy to implement and needs very few computations. Moreover, the method is suitable for and easy to integrate with different pulse width modulation schemes. The effectiveness and feasibility of the proposed method is verified by simulation and experiment. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) has several submodules in cascade. To control the submodule capacitors voltage, a new generalized dynamic voltage balancing algorithm along with a simple pulse width modulator structure is proposed in this paper. With proposed pulse width modulator structure, the dynamic voltage balancing algorithm can be easily implemented with any type of carrier based pulse width modulation (including level-shifted and phase-shifted pulse width modulation) scheme without any modifications. This method does not require the sorting technique for selection of submodule capacitors voltage. The performance of the proposed voltage balancing algorithm is presented for MMC with three-level flying capacitor submodules (MMC-3L-FC). The proposed method is also applicable to the conventional two-level half bridge submodules as well. The effectiveness of the proposed voltage balancing algorithm is verified with the phase-shifted carrier-based pulse with modulation scheme. The results obtained from the MATLAB/SIMULINK simulations on 6-kV/ 2.5-MW system and the dSPACE DS1103-based laboratory prototype of 208-V/3-kVA MMC-3L-FC system are in close relationship, and thus, the proposed methodology is validated. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant dual-active bridge (DAB) converter, which uses a tuned capacitor–inductor–capacitor network. In comparison to the conventional DABs, the proposed topology significantly reduces the bridge currents, lowering both conduction and switching losses and improving the bridge power factors. A mathematical model, which predicts the behavior of the proposed system, is presented to show that both the magnitude and direction of the power flow can be controlled through either relative phase angle or pulse width modulation of voltages produced by the bridges. The viability of the proposed concept is verified through simulation. Experimental results of a 4- kW prototype converter, which has an efficiency of 95% at rated power, are also presented with discussions to demonstrate the improved performance of this topology. [ABSTRACT FROM AUTHOR]

A family of “Two-Switch Boosting Switched-Capacitor Converters (TBSC)” is introduced, which distinguishes itself from the prior arts by symmetrically interleaved operation, reduced output ripple, low yet even voltage stress on components, and systematic expandability. Along with the topologies, a modeling method is formulated, which provokes the converter regulation method through duty cycle and frequency adjustment. In addition, the paper also provides guidance for circuit components and parameter selection. A 1-kW 3X TBSC was built to demonstrate the converter feasibility, regulation capability via duty cycle and frequency, which achieved a peak efficiency of 97.5% at the rated power. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage balancing method for flying capacitor multilevel converters based on phase-disposition pulse width modulation (PD-PWM) using optimal transitions between converter switching states. The optimal transitions between converter switching states are possible due to the converter states' redundancy and are decided with the continuous evaluation and minimization of a cost function. Simulation and experimental results verify the robustness of the proposed voltage balancing method against different load conditions. A significant reduction of the average switching frequency is achieved, when compared to the use of the optimal state voltage balancing method, where the optimal states are decided independently for each voltage level ignoring how transitions impact on the converter switching frequency. Moreover, the line-to-line output voltages are compared with the ones obtained with other modulation techniques in terms of total harmonic distortion values, and PD-PWM with the proposed voltage balancing method produces the best results. [ABSTRACT FROM AUTHOR]

Five-level active neutral-point clamped (5L-ANPC) converter is an attractive topology for high-power medium-voltage motor drives. This paper presents a capacitor voltage-balancing method for the 5L-ANPC converter, including the voltage balancing of dc-link capacitors and flying capacitors. In order to ensure that the series-connected or high-voltage switches of the 5L-ANPC converter are operated at fundamental frequency and the other switches are operated at a constant switching frequency, phase-shifted pulse width modulation is used to control this converter. The relationship between the average neutral-point current and zero-sequence voltage is investigated, and an optimum zero-sequence voltage is calculated to regulate the neutral-point potential. The voltage across the flying capacitor is also regulated by adjusting the switching duty cycles of two PWM signals, which varies the operation time of redundant switching states in each switching period. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is attractive for medium- and high-power applications because of its high modularity, availability, and power quality. In this paper, the current ripple on the dc link of the three-phase MMC derived from the phase-shifted carrier-based pulse-width modulation scheme is analyzed. A control strategy is proposed for the current ripple elimination. Through the regulation of the phase-shifted angles of the carrier waves in the three phases of the MMC, the current ripple on the dc link of the three-phase MMC can be effectively eliminated. Simulations and experimental studies of the MMC were conducted, and the results confirm the effectiveness of the proposed current ripple elimination control. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) has been a subject of increasing importance for medium/high-power energy conversion systems. Over the past few years, significant research has been done to address the technical challenges associated with the operation and control of the MMC. In this paper, a general overview of the basics of operation of the MMC along with its control challenges are discussed, and a review of state-of-the-art control strategies and trends is presented. Finally, the applications of the MMC and their challenges are highlighted. [ABSTRACT FROM AUTHOR]

This paper evaluates two different concepts for the control of the modular multilevel converter (MMC). Generally aiming at medium voltage applications, the considered MMC topology has a low number of submodules, and a pulse-width modulation (PWM) scheme is applied. A model predictive control (MPC) algorithm is developed and experimentally compared to a cascaded control scheme based on conventional PI controllers, which has been proposed by Hagiwara and Akagi. Steady-state and dynamic system performance as well as computational power requirements are discussed. The basis for the comparison is a scaled converter test bench operating from 560-V dc voltage. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) has become one of the most promising converter topologies for future high-power applications. A challenging issue of the MMC is the voltage balancing among arm capacitors. A good overall control system is also vital for the MMC, which should be based on sound mathematical model, readily adaptable for different applications, and capable of high performance. This paper presents a general control structure for MMC inverters, which is suitable for both voltage-based and energy-based control methods, and includes voltage balancing between the upper and lower arms. A new method for voltage balancing among arm capacitors, which is based on an improved pulse-width modulation, is also presented. The proposed method avoids some major disadvantages found in present voltage balancing methods, such as dependence on computation-intensive voltage sorting algorithms, extra switching actions, interference with output voltage, etc. Furthermore, all switching actions are evenly distributed among power devices. The proposed control system as a whole can serve as a promising solution for practical applications, especially when the number of submodules is fairly high. Simulation and experimental results verify the effectiveness of the proposed methods. [ABSTRACT FROM AUTHOR]

This paper proposes a novel wide-range soft-switching pulse-width modulation three-level (TL) combined dc-dc converter characterized with no added primary clamping devices and reduced output inductance value. It is well suited for high input voltage dc-dc industrial applications due to following desirable features: all the switches sustain half of the input voltage; off state voltage of the switches is directly clamped by the bulky input capacitors, and no added primary clamping devices such as clamping diodes, flying capacitors, are required; TL waveform before output filter can be achieved, which significantly reduces the value of the output inductance; the modified phase-shift control method can be utilized to achieve wide output range. The converter can obtain zero-voltage switching (ZVS) for all power switches in wide load range; furthermore, less conduction loss is added to achieve ZVS. The operation and theoretical analysis of the proposed converter are presented. Experiments are carried out to validate the proposed converter, and efficiency curves are tested and given. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching technique for cascaded H -bridge (CHB) converters is proposed. To take advantage of both low- and high-frequency modulation techniques, a hybrid modulation method is utilized. The proposed technique employs the low-frequency switching for voltage balancing of the dc-link capacitors, and the high-frequency sinusoidal pulse-width modulation switching for shaping the input ac current. Using the proposed technique, the stable operating region of CHB converters is extended. The proposed technique is capable of maintaining the dc voltages balanced even under critical operating conditions in which the load of one H-bridge cell is removed. The validity and effectiveness of the proposed method is confirmed by several simulation and experimental tests on a seven-level CHB rectifier. [ABSTRACT FROM AUTHOR]

Multilevel flying capacitor (FC) converters provide natural capacitor voltage balance under phase-shifted pulse width modulation (PS-PWM). However, natural balancing may not be robust enough to maintain the voltages at the reference values, especially under certain transient conditions. Furthermore, natural balancing dynamics depend on the load and it may be very slow in some practical applications. Therefore, a more robust balancing mechanism of maintaining the FC voltages at the desired values is required. This paper proposes a new closed-loop voltage-balancing method for the multilevel FC converters using PS-PWM. The proposed method balances the voltages of the FCs by modifying the duty cycle of each switch of the FC converter using a proportional controller. The crossed effect between FC currents and duty cycles is considered and is used for optimal FC voltage balancing. Simulation and experimental results verify that the proposed voltage-balancing method is very robust to different operating conditions, such as load transients, linear/nonlinear and unbalanced loads. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is attractive for medium- or high-power applications because of the advantages of its high modularity, availability, and high power quality. The voltage balancing of the floating capacitors in the cascaded submodules of the MMC is a key issue. In this paper, a voltage-balancing control method is proposed. This method uses the phase-shifted carrier-based pulsewidth modulation scheme to control high-frequency current components for capacitor voltage balancing in the MMC without measuring the arm currents. Simulations and experimental studies of the MMC were conducted, and the results confirm the effectiveness of the proposed capacitor voltage-balancing control method. [ABSTRACT FROM AUTHOR]

This paper proposes a new zero-voltage switching (ZVS) pulse width modulation (PWM) three-level (TL) full-bridge (FB) dc–dc converter, which is composed of a TL FB converter and a TL half-bridge (HB) converter. It is well suited for high input voltage and high-power applications. The proposed topology has the following attractive features: off-state voltage on all switches in the circuit is only half of the input voltage; full input voltage is utilized on the load for the whole operating range; TL output waveform is achieved, which significantly reduces the requirements for the input and output filters; simple switching scheme can be used to control the output voltage in wide range. The converter can achieve ZVS for all power switches in wide load range and even at light load condition; furthermore, less conduction loss is added to achieve soft switching. The operation and important analysis of the proposed converter are given. Experiments are carried out to validate the proposed converter, and efficiency curves are tested and given. [ABSTRACT FROM AUTHOR]

This paper proposes a novel nonisolated flyback switching capacitor voltage regulator. The converter is a combination of a switching capacitor converter and a pulsewidth modulation voltage regulator, and it has the following advantages: 1) the switches achieve zero voltage switching (ZVS); 2) the self-driven method of the synchronous rectifier (SR) is applied to save the drive loss and the body diode conduction loss; 3) the transformer leakage inductor is utilized to realize the soft switching of the switches; and 4) single-phase option makes it more flexible. Its derivation, operation principle, and self-driven method are presented. A single-phase 700 kHz 1.2 V/35 A output point-of-load prototype was built to verify the analysis. [ABSTRACT FROM AUTHOR]

Hybrid cascade multilevel inverters combine semiconductor devices of different voltage ratings and technologies, which theoretically allow high efficiency to be achieved. The bottlenecks of these topologies are, however, the need for isolated supplies for the cells and the lack of modularity. This paper focuses on the design and control of high-resolution, high-efficiency multilevel inverters with simplified dc power supplies. It introduces several rules for systematically designing the dc voltages of the cells, for which all unsupplied capacitor voltages can be regulated. Six classes of inverters are obtained covering single- and three-phase, staircase and pulsewidth-modulated (PWM) inverters. New configurations of hybrid cascade multilevel inverters are obtained for each class. A double modulation strategy with two different frequencies is proposed that allows switching losses of PWM inverters to be reduced. Decoupled mechanisms are proposed for the total and internal energy balances. It is shown how to make the design robust by taking into account conversion losses and large dc-voltage imbalances in the design and control. An analysis of the maximum voltage utilization and efficiency of the resulting configurations is carried out. The effectiveness of the novel concepts is validated experimentally for two of the proposed topologies. [ABSTRACT FROM PUBLISHER]

This paper further develops a model predictive control (MPC) scheme which is able to exploit the large number of redundant switching states available in a multilevel H-bridge StatCom (H-StatCom). The new sections of the scheme provide optimized methods to tradeoff the harmonic performance with converter switching losses and capacitor voltage ripple. Varying the pulse placement within the modulation scheme and modifying the heuristic model of the voltage balancing characteristics allows the MPC scheme to achieve superior performance to that of the industry standard phase shifted carrier modulation technique. The effects of capacitor voltage ripple on the lifetime of the capacitors are also investigated. It is shown that the MPC scheme can reduce capacitor voltage ripple and increase capacitor lifetime. Simulation and experimental results are presented that confirm the correct operation of the control and modulation strategies. [ABSTRACT FROM PUBLISHER]

It is important to improve the overall efficiency of a photovoltaic (PV) inverter when it is connected to the grid. Fundamentally, the conversion efficiency from dc to ac power of an inverter is important. However, in the presence of partial shading, maximum power point tracking (MPPT) on PV modules is more important than the conversion efficiency. In this paper, a new control method for a three-level inverter is proposed. With the proposed method, each dc-link voltage of the three-level inverter can be asymmetrically regulated. When PV modules are split into two and each split module is connected to the respective dc-link capacitors of the inverter, the asymmetric control can be helpful because separate MPPTs are possible. The effectiveness of the proposed method was examined through experiments with a T-type three-level inverter, where each dc-link capacitor was supplied by a PV simulator emulating two separate PV modules under different shading conditions. [ABSTRACT FROM AUTHOR]