Search

The main standard for avionic equipment DO-160G defines a set of tests that require compliance before the employment of a device in aircraft. An important test involves the generator voltage and consequential current distortion of the three-phase load in the variable 360–800 Hz frequency grid. The main purpose of this paper is to present and analyze a systematic design methodology for three-phase boost and buck rectifiers in order to meet with the voltage distortion test requirement. For a given voltage harmonic profile, the current harmonic limits that have to be satisfied are translated into equivalent per-harmonic admittances and a profile of maximum rectifier input admittance versus frequency is obtained. The defined profile, due to normalization, is applicable to arbitrary power level with simple shifting by the base admittance governed by the converter nominal power. It is shown that for boost-type rectifiers there is a tradeoff between current controller bandwidth and input inductor size, while for the buck-type rectifiers main limitation lies in the input LC filter design used for differential electromagnetic interference filtering. The experimental results conducted on an SiC three-phase 10 kW VIENNA rectifier are tightly backing up the proposed theoretical analysis. This paper is accompanied by three videos demonstrating experimental measurement of d-axis open-loop duty cycle to inductor current transfer function, loop-gain of d-axis current controller with 3.8 kHz bandwidth and variable grid frequency 360–800 Hz operation of the converter under 0% and 10% input three-phase voltage total harmonic distortion. [ABSTRACT FROM AUTHOR]

This paper investigates a Vienna rectifier as a charger for series-connected battery packs. Focusing on carrier-based pulsewidth modulation (CBPWM), the ripple current flowing through the neutral point (NP) results in the voltage oscillation if the loads are resistive. To reduce the ripple of average NP current with mitigated distortion under balanced and unbalanced dc-link voltages conditions, a novel CBPWM with segmented component injection scheme (SCIS) is proposed in this paper. After dc component injection, continuous intervals for optimized component injection and clamping intervals for compensation component injection are identified. Optimized components are calculated originally based on unbalanced factor to make the average NP current zero-size in one switching period. Moreover, unique compensation components generate suitable NP current to shape the sinusoidal input currents according to the circuit analysis. In consequence, the SCIS not only keeps the input current with low-harmonic distortion, but also minimizes the oscillation of dc-link voltage under balanced and unbalanced conditions. In addition, the value of the NP current during the clamping intervals is analyzed under various operating conditions. The effectiveness and the performance of the proposed SCIS are verified by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes the predictive control with the discrete space-vector modulation (DSVM) for Vienna rectifier connecting to the permanent magnet synchronous generator (PMSG) of the wind turbine system (WTS). Since Vienna rectifier has the special operation principle, Vienna rectifier generates only the feasible eight voltage vectors, which can be a candidate vector for the predictive control, depending on the sign of the input currents. In the proposed predictive control, the feasible voltage vectors are extended from 8 to 19 consisting the 8 original voltage vectors and 11 virtual voltage vectors by using the DSVM for improving the current quality related to the torque ripple, vibration, and noise, and the neutral-point voltage balance with low voltage ripple is guaranteed by using the offset value calculated based on the model of two dc-link capacitors in Vienna rectifier. The scheme for reducing calculation burden is applied in selecting the candidate vector. In addition, the limited operation range for the maximum torque per ampere control of PMSG connected to Vienna rectifier is analyzed. The performance of the proposed predictive control with DSVM for Vienna rectifier with PMSGs is verified in simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper proposes a generalized design framework for three-phase Vienna rectifiers to handle the neutral point voltage balance issue. On the basis of the design framework, it is convenient to construct various neutral point voltage balancing methods with the guarantee of stability. As demonstration, three representative neutral point voltage balance approaches are presented by choosing different zero-sequence voltages. A comprehensive comparison among the three approaches is given in the aspects of input current quality, capacitor voltage fluctuation, and system efficiency. The comparison results provide guidance for constructing the most appropriate approach based on the specific requirement. Finally, simulation and experimental results verify the correctness and effectiveness of the presented approaches and the related performance analysis. [ABSTRACT FROM AUTHOR]

The VIENNA rectifier is increasingly being considered as the active front-end converter in many applications that do not require regeneration or controllable input reactive power. In such applications, this rectifier is normally operated at unity source displacement factor, which derates its nominal voltampere (VA) rating. Moreover, in the “source voltage oriented” reference frame that is normally used for control, this rectifier has complex operating limits on the rectifier terminal voltage (imposed by the operating conditions), which needs to be computed online to avoid the line currents from going through zero-crossing distortions. Also, the source voltage has to be either measured or estimated, which further increases the cost and/or computational burden. This paper proposes a control method that eliminates the requirement of the input voltage sensors (or estimators) and makes the limits on the rectifier terminal voltage far simpler to compute. The control method is implemented in the input line current oriented reference frame, considering unity displacement factor at the rectifier input terminals, which minimizes the VA rating of the rectifier (for a given rated load power). The proposed sensorless current-oriented control approach is compared with the conventional voltage-oriented control strategy through experimental results. [ABSTRACT FROM AUTHOR]

This paper identifies extra junction capacitances and switching commutation loops introduced by line-frequency devices (i.e., non-active every other half line cycle) in three-level ac/dc converters and investigates the corresponding effects. Junction capacitances and power loops are well known as the key factors that impact converter switching loss and device stress, thus influence device selection, power stage layout, and thermal design. By examining switching transients of the commonly used T-shaped and I-shaped three-level converters, the cause and mechanism of the extra junction capacitances and power loops are presented. The impacts on switching loss, device voltage stress, and ac-side voltage/current distortion are respectively reported and analyzed. A loss calculation scheme for the three-level converter to include that extra loss is proposed. A power layout scheme to mitigate the device voltage stress is provided. Compensation and modeling of the voltage and current distortion are also proposed. Experimental results conducted on several types of three-level converter prototypes including a gallium nitride based 115 $V_{{\text{ac}}}{\text{/650}}$ Vdc/1.5-kW/450-kHz Vienna-type rectifier and a SiC mosfet based 1-kV/10-kW/280-kHz three-level active neutral-point-clamped inverter confirm the presented effects and verify the associated analysis and solutions. [ABSTRACT FROM AUTHOR]