Search

This paper presents a bridgeless dual-mode single power-conversion ac–dc converter that can achieve a high conversion efficiency. By adopting a bidirectional switch, we remove a full-bridge diode rectifier from the grid side of the proposed converter, and thereby, reduce the number of components and the primary-side conduction loss. To adapt the converter to 1-kW power applications with a bidirectional switch, we used a series-resonant circuit in the output voltage doubler on the secondary side. The series-resonant circuit also provides zero-current switching turn-off at the output diode, and thereby, reduces the reverse-recovery loss. To attain medium–high power capability with an appropriate transformer, the proposed converter operates in both discontinuous conduction mode and continuous conduction mode. The operation principle of the converter is presented and analyzed. By using the dual-mode control algorithm, the proposed converter achieves a high power factor of 0.994 and maximum efficiency of 97.3 $\%$. Experimental results for a prototype 1-kW ac–dc converter verify these characteristics. [ABSTRACT FROM AUTHOR]

This paper proposes a novel pulsewidth modulation cell-level diffusion charge redistribution (DCR) converter based on a switched capacitor converter (SCC) utilizing diffusion capacitance of photovoltaic (PV) cells for PV modules under partial shading. Although a discrete inductor and capacitor are additionally necessary, Joule losses associated with switching operations can be reduced compared to the conventional capacitorless DCR converter. First, ac impedance measurement for a PV cell with 125 × 125 mm was performed, and the diffusion capacitance values were measured to be approximately 6.0 mF at its maximum power point voltage of 0.574 V. Second, the theoretical loss model was derived based on the detailed analysis, and it revealed that an optimal duty cycle achieving the lowest Joule loss was dependent on shading conditions. Third, a dual maximum power point tracking (MPPT) algorithm that controls duty cycles of not only the DCR converter, but a front-end boost converter is also proposed. With the dual MPPT control, the DPP converter operates at its optimal duty cycle to minimize the Joule loss while the boost converter seeks the MPP. The experimental results demonstrated that the maximum power significantly increased, thanks to the DCR converter, and that both the DCR and boost converters operated with respective optimal duty cycles. [ABSTRACT FROM AUTHOR]

In this paper, an integrated step-up inverter without transformer is investigated for photovoltaic (PV) power generation. The proposed topology can be derived by combining a traditional boost converter with a single-phase full bridge dc–ac converter. The main features of the integrated inverter are: First, the leakage current caused by the solar cell array-to-ground parasitic capacitance can be theoretically reduced to zero due to the characteristics of the converter configuration, which can improve the efficiency and the reliability of the PV generation system; second, the output ac voltage of the proposed inverter can be higher than the input dc voltage, which is capable of connecting low voltage PV panels to the grid; third, only five active switches are used in the presented inverter, and those switching devices can be synchronously driven by various sinusoidal pulsewidth modulation methods based on the carrier; therefore, the proposed inverter is compact and with curtailed cost. The working principle and analysis of the proposed integrated inverter are elaborated. Finally, simulation and experimental results are obtained in a lab prototype, which agree well with the theoretical analysis. [ABSTRACT FROM AUTHOR]

A novel high step-down dc–dc converter with voltage demultiplier cell is proposed in this paper, which is widely used in the high step-down applications such as electric vehicle and digital circuits. The combination of switched-capacitor and coupled-inductor is employed to build extended voltage demultiplier in the proposed converter, which makes a quite higher voltage conversion ratio than that of the existing counterparts. Thus, the proposed converter can achieve extremely low output voltage with an appropriate duty ratio, and the extreme duty cycle is avoided. Accordingly, voltage stress on power switches is greatly reduced. Then, mosfets with low conduction resistance could be utilized to reduce conduction loss. Importantly, zero-voltage switching could be achieved for the main switch, which promotes the conversion efficiency further. In addition, the coupled inductor operates not only as a filter inductor, but also as a transformer when the main switch is in the off state, which reduces the volume of the magnetic core and improves the power density of the converter. The operation principle, performance analysis, design considerations of the proposed converter and performance comparison with recent counterparts are discussed in detail, and finally, an experimental prototype is built to verify the theoretical analysis and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage single-switch soft-switching (S6) power factor correction (PFC) converter to enhance the current shaping performance and reduce the total harmonic distortion. This improvement is achieved by the aid of an auxiliary winding which is used to lower the input current harmonics and also achieve soft-switching condition. As a result, the switching losses are reduced and harmonic content of the input current is improved noticeably in comparison to the conventional S6 PFC converter. Also, the total number of semiconductor elements is reduced in the proposed topology which results in lower cost and higher efficiency. The operating modes of the proposed converter are discussed in detail and the design procedure is presented. A 200-kHz prototype of the proposed converter is implemented and the obtained results are provided to verify the converter theoretical analysis and operation. [ABSTRACT FROM AUTHOR]

When providing ac output, modular multilevel converters (MMCs) experience power fluctuation in the phase arms. The power fluctuation causes voltage ripple on the module capacitors, which grows with the output power and inversely to the output frequency. Thus, low-frequency operations of MMCs, e.g., for motor drives, require injecting common-mode voltages and circulating currents, and strict dc voltage output relative to ground is impossible. To address this problem, this paper introduces a novel module topology that allows parallel module connectivity in addition to the series and bypass states. The parallel state directly transfers power across the modules and arms to cancel the power fluctuations and hence suppresses the capacitor voltage ripple. The proposed series/parallel converter can operate at a wide frequency range down to dc without common-mode voltages or circulating currents; it also allows sensorless operation and full utilization of the components at higher output frequencies. We present detailed simulation and experiment results to characterize the advantages and limitations of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage-source parallel resonant Class E inverter. The proposed circuit has a shunt capacitor including parasitic capacitance of a switching device and achieves zero-voltage switching and zero-voltage derivative switching at turning-on like a classical Class E inverter. Therefore, high power conversion efficiency is achieved under high operating frequency. Unlike the other Class E inverters, the proposed circuit has no choke inductor or dc blocking capacitor. Moreover, it has a parallel resonant tank unlike the classical Class E inverter. Thus, a circuit protection is not required in a wireless power transfer system. Circuit analysis, circuit simulations, and circuit experiments were carried out. The experimental circuit performed the desired operation and the power conversion efficiency was 93.2% with the output power 4.76 W at the operating frequency 1 MHz. [ABSTRACT FROM AUTHOR]

In this paper, a new class of dc–dc converter topologies based on capacitive link dc–dc converters—Ćuk, SEPIC, and Zeta converters—that operate under the critical conduction mode has been proposed. The proposed converters are the extensions of quasi-square-wave zero-current-switching converters, which use an auxiliary circuit to provide zero-current and zero-voltage switching for all semiconductor switches at both turn on and turn off transitions and eliminate voltage ringing across the output switch. Using the proposed auxiliary circuit, the value of dv/dt has been diminished; hence, the EMI of the proposed topology is significantly reduced compared to the conventional quasi-square-wave zero-current-switching converters. To verify the operation of the proposed converter and confirm its advantages, an experimental prototype has been implemented, and the experimental results and the efficiency of the proposed converter have been compared with the conventional quasi-square-wave zero-current-switching converters. [ABSTRACT FROM AUTHOR]

This paper proposes a new 7-level inverter topology for induction motor drives. It is a hybrid topology formed by cascading a 5-level active neutral-point-clamped inverter with a 3-level T-type converter. It is obtained using low-voltage semiconductor devices with voltage blocking capability of Vdc/3 and Vdc/6. The topology uses three floating capacitors per phase, which are balanced within a pulsewidth modulation (PWM) switching duration using switching-state redundancies for each pole-voltage level. Topology forms two stacks at the front-end, which requires individual symmetrical dc source. The analysis of switching loss and conduction loss is performed and compared with some of the existing 7-level multi-level inverters reported in various literatures to show the advantages of the proposed topology. Furthermore, the single dc source operation with two stacked capacitors and closed-loop control of neutral-point voltage using symmetrical six-phase induction motor is proposed. The voltage-control algorithms for floating capacitors and dc-link stacked capacitors are proposed, which are independent of load power factor and modulation index. Open-loop V/f and closed-loop rotor field oriented control are performed, and various results at steady and transient states are presented to validate the aforementioned claims. [ABSTRACT FROM AUTHOR]

In the applications such as mixed-color light emitting diode (LED) lighting system, LED drivers are always required to provide constant current for each LED string and each current should be controlled independently. For this purpose, a single-stage series-type LED driver with independent control of N-channel output currents is proposed in this paper. The function of power factor correction can be realized inherently to obtain high power factor. N active output units, each one made up of a power switch, a diode, and an output filter capacitor, are series-connected to form the series-type N-channel outputs structure. According to different current reference values, N-channel output currents can be independently regulated just by sampling each output current to adjust the duty cycle of each secondary output-switch automatically. The operating principle and independent closed-loop control strategy of the proposed LED driver with N = 3 are analyzed as an example in detail. Finally, the quantitative parameter design method for a 120 W prototype is elaborated. And, the experimental results are presented to verify the effectiveness of the LED driver and the correctness of parameter design method. [ABSTRACT FROM AUTHOR]

In order to match the long life span of light emitting diodes (LEDs), electrolytic capacitor-less off-line LED drivers have been intensely developed. However, the relatively low power efficiency is a common issue for many electrolytic capacitor-less designs. In this paper, a more efficient single-coupled-inductor multiple-output (SIMO) LED driver is proposed. The electrolytic capacitor-less design is targeted for lighting applications with color mixing and color temperature adjustment, where a small capacitance actively balances the power difference between the ac input and multiple dc outputs. Using energy-flow-path optimization, the proposed LED driver has some direct and efficient energy flow paths. In particular, additional energy flow paths are implemented, connecting directly from the small capacitance to multiple dc outputs. Thus, the overall power efficiency is improved. Furthermore, the proposed LED driver is designed with a carrier-based control without the high-precision current sensor for the single-coupled inductor, and thus simpler signal sampling and reduced control complexity can be achieved for independent regulations of multiple dc outputs. [ABSTRACT FROM AUTHOR]

Modules with series and parallel connectivity add new features and operation modes to modular multilevel converters (MMCs). Compared to full- and half-bridges, the series/parallel modules allow sensorless module balancing and reduce conduction loss with the same semiconductor area. However, in high-voltage applications with limited switching rates, the sensorless operation of the series/parallel modules suffers from large charge-balancing currents. This paper introduces a series/parallel module variant with a small port inductor. The port inductor suppresses the charge-balancing current despite low switching rates. We also propose a carrier-based modulation framework and show the importance of the carrier assignment in terms of efficiency and balancing. The proposed module and the modulation method are verified on a lab setup with module switching rates down to 200 Hz. The module voltages are kept within a narrow band with the charge-balancing currents below 5% of the arm current. The experimental results show practicality and advantages of the new series/parallel modules in high-voltage MMC applications. [ABSTRACT FROM AUTHOR]

Fault diagnosis is indispensable for the reliable operation of modular multilevel converters (MMCs). This paper presents a submodule voltage similarity-based, real-time, and fast open-circuit fault diagnosis method for MMCs. The proposed fault detection and location (FDL) method is derived based on the similarity analysis of capacitor voltages under both normal and fault conditions. Due to the absence of the discharging current path caused by the open-circuit fault, capacitor voltage of the submodule with the faulty switch will differ from those with healthy switches. This characteristic can be extracted by designing the correlation coefficients of the capacitor voltages at the same arm. With the help of correlation coefficients, the open-circuit fault can be located at the early stage before the capacitor voltage is charged very high. All the data required for the proposed FDL method can be obtained by the available sampled data for the control scheme of MMCs. No extra measurement or hardware is required. Experimental results validate that the proposed FDL method can detect and locate the open-circuit fault rapidly and accurately within one fundamental period. [ABSTRACT FROM AUTHOR]

It is considerable to reduce the computation load while keeping a good total harmonic distortion (THD) performance for the modular multilevel converter (MMC) with model predictive control (MPC). In this paper, the discrete-time mathematical model of the MMC is derived and the output voltage ripples of the cascaded submodules (SMs) are analyzed in detail. Accordingly, a modified increased-level MPC method A (IL-MPC-A) is proposed with 2N + 1 ac-side output voltage levels. The computation load is significantly reduced without losing the harmonic circulating currents suppression and capacitor voltage ripples compensation capabilities. In this method, the cost function minimization step and capacitor voltage sorting algorithm are combined to determine the optimal control option. In addition, to avoid the selection of weighting factors and further reduce the computation load as the increasing of the SM number, another modified IL-MPC-B is proposed by directly calculating the optimal ac-side output voltage level and arm summation voltage according to the discrete-time mathematical model. As a result, the ac-side output current and circulating current controls are decoupled. Furthermore, the capacitor voltages are balanced with a proposed control scheme by adjusting the circulating current reference. The effectiveness of the proposed MPC methods is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

A multiphase-interleaved non-isolated high step-up dc/dc resonant converter for high-current applications with wide load range is proposed in this paper. The converter consists of an inverter stage with multiple resonant inverters in parallel interleaving operation that is cascaded to a common diode–capacitor rectifier stage. The topology of the inverter stage is a variation of class E inverter, which is designed for voltage boosting and of which the voltage gain is insensitive to load change. The rectifier stage comprises multiple pairs (correlated to the number of inverters in parallel) of diodes in parallel and a small output capacitor, which makes it simple to implement and of low cost. Together, the voltage gain variance of the converter can be confined within a small value and zero voltage switching operation can be maintained over a wide load range. A detailed mathematical analysis of the proposed converter is conducted for systematizing its design. A prototype of the proposed converter with an input voltage of 23.6 V, a rated output voltage of 190 V, and a rated output power of 80 W at 486 kHz is constructed for verification. A frequency controller is implemented to achieve fine regulation of the output voltage. [ABSTRACT FROM AUTHOR]

The derivation and implementation of the natural switching surfaces (NSS) considering certain parametric uncertainties for a flyback converter operating in the boundary conduction mode is the main focus of this paper. The NSS with nominal parameters presents many benefits for the control of nonlinear systems; for example, fast transient response under load-changing conditions. However, the performance worsens considerably when the converter actual parameters are different from the ones used in the design process. Therefore, a novel control strategy for NSS considering the effects of parameter uncertainties is proposed. This control law can estimate and adapt the control trajectories in a minimum number of switching cycles to obtain excellent performances even under extreme parameter uncertainties. The analytical derivation of the proposed adaptive switching surfaces is presented together with simulations and experimental results showing adequate performance under different tests, including comparisons with a standard PI controller. [ABSTRACT FROM AUTHOR]

In high gain voltage conversion applications, the low-side switches usually suffer large current stress, resulting in dominate switching loss. In this paper, a general soft-switching method based on an advanced interleaved high-step-up converter, which features excellent performance but works in hard-switching, is presented to combat this issue by using a plug-play resonant circuit. Under this soft-switching method, the main switches reach zero-voltage switching (ZVS) turn-on and ZVS turn-off, and the soft-switching condition is derived. Meanwhile, the added auxiliary switches could be turned off under ZVS condition and turned on under zero-current switching condition as well. More importantly, due to its location out of the energy transferring path, the auxiliary circuit will never lead gain lost to the converter and maintain its other existing merits, such as current auto-balancing and diode inverse-recovery well. A 1-kW prototype is built and tested to verify the significant efficiency improvement and merits maintenance for the proposed converter considering active resonant soft switching. [ABSTRACT FROM AUTHOR]

This paper investigates basic stability properties of the three-level flying-capacitor Buck converter when operated under current-mode control (CMC). The proposed analysis is developed for both peak CMC (P-CMC) and valley CMC (V-CMC), and addresses both the static instability of the inductor current and the flying capacitor (FC) voltage runaway phenomenon. Conditions for avoiding current subharmonic oscillations are derived first, along with the expressions of the minimal compensation ramp, which guarantee current stability throughout the entire operating range. As for the stability of the FC voltage, P-CMC results to be inherently unstable unless the converter operates with a relatively large peak-to-peak inductor-current ripple, a feature not yet recognized in the literature. However, V-CMC results to be inherently stable once the static instability of the current is eliminated with an external compensating ramp—a property that has been highlighted in the literature but never formally proven. The proposed analysis is verified both using a simulation model and experimentally using a 3.3-V, 500-mA, 500-kHz prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage of the inverter can be increased from 0.577 to 0.637 V\text{dc} without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction motor drive can be operated till the full speed range (0–50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors. The inverter topology and its operation for extending the modulation range is analyzed extensively. Simulation and experimental results for both steady-state and dynamic operating conditions are presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

In high-voltage applications, the magnitude of total semiconductor losses (on-state and switching) determines the viability of modular-type multilevel converters. Therefore, this paper presents a new cell arrangement that aims to lower total semiconductor loss of the modular multilevel converter (MMC) to less than that of the half-bridge modular multilevel converter (HB-MMC). Additional attributes of the proposed cell are: it eliminates the protective thyristors used in conventional half-bridge cells that deviate part of the dc-fault current away from the antiparallel diode of the main switch when the converter is blocked during a dc short-circuit fault, and it can facilitate continued operation of the MMC during cell failures without the need for a mechanical bypass switch. Thus, the MMC that uses the proposed cell retains all advantages of the HB-MMC such as full modularity of the power circuit and internal fault management. The claimed attributes of the proposed cell are verified using illustrative simulations and reduced scale experimentations. Additionally, this paper provides brief and critical discussions that highlight the attributes and limitations of popular MMC control methods and different MMC cells structures proposed in the literature, considering the power electronic system perspective. [ABSTRACT FROM AUTHOR]

This paper extends the voltage-doubler concept to the single-phase SEPIC rectifier in discontinuous conduction mode and, as a consequence, novel rectifiers are proposed. A comparison with the classic SEPIC rectifier shows that the proposed converters can either provide reduced voltage stress on the semiconductors for the same output voltage level or supply double the gain of the output voltage with the same voltage stress. The proposed voltage-doubler SEPIC rectifiers provide a high power factor with no current control and they can be applied in order to improve the static gain of the structure, which can make the SEPIC rectifier suitable for applications that require a high voltage level. In this paper, the generic structure based on a three-state switch, four different implementations of the proposed concept (including bridgeless structures), steady-state analysis, a dynamic model, system control, and experimental results are presented. The proposed rectifiers were verified by experimental results obtained with a prototype built with the following specifications: 1000 W output power, 220 V input voltage, 400 V output voltage, and 50 kHz switching frequency. Peak efficiency of 95.84%, THD of 2%, and power factor of 0.9997 were obtained and, most importantly, double the gain of the output voltage was verified. [ABSTRACT FROM AUTHOR]

This paper presents the analysis and design of an isolated high-voltage LLC resonant dc–dc full-bridge converter based on symmetrical quadrupler rectifier (SQR). Unlike conventional Cockcroft–Walton and full-bridge diode rectifiers, the SQR circuit provides significant improvement in power density by reducing the transformer turns-ratio without much increase in the output impedance. Moreover, the LLC converter can provide additional voltage boost, if operated, below the series resonant frequency of the LLC tank. The operating region of the converter is chosen in such a way that the converter always operates in ZVS for all line and load conditions with additional voltage boost. A new method based on basic differential equation is proposed for the accurate analysis and design of the converter and subsequently, the key results are compared with a first harmonic approximation based analysis method. A 120 V dc input, 2 kV output, 200 W laboratory prototype has been designed, built, and tested. Simulation and experimental results shown in this paper demonstrate the validity of the analysis and design of the presented converter. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

Increasing demands for power supplies have contributed to the population of high-frequency ac (HFAC) power distribution system (PDS), and in order to increase the power capacity, multilevel inverters (MLIs) frequently serving as the high-frequency (HF) source-stage have obtained a prominent development. Existing MLIs commonly use more than one voltage source or a great number of power devices to enlarge the level numbers, and HF modulation (HFM) methods are usually adopted to decrease the total harmonic distortion (THD). All of these have increased the complexity and decreased the efficiency for the conversion from dc to HF ac. In this paper, a nine-level inverter employing only one input source and fewer components is proposed for HFAC PDS. It makes full use of the conversion of series and parallel connections of one voltage source and two capacitors to realize nine output levels, thus lower THD can be obtained without HFM methods. The voltage stress on power devices is relatively relieved, which has broadened its range of applications as well. Moreover, the proposed nine-level inverter is equipped with the inherent self-voltage balancing ability, thus the modulation algorithm gets simplified. The circuit structure, modulation method, capacitor calculation, loss analysis, and performance comparisons are presented in this paper, and all the superior performances of the proposed nine-level inverter are verified by simulation and experimental prototypes with rated output power of 200 W. The accordance of theoretical analysis, simulation, and experimental results confirms the feasibility of proposed nine-level inverter. [ABSTRACT FROM AUTHOR]

The matrix converter (MC) is a direct ac–ac power converter without an intermediate dc link. It has several attractive features, such as high power density, four-quadrant operation, and bidirectional power flow. However, the application of MCs in high-voltage and high-power systems is still limited by the device voltage levels. It is well known that the multilevel power converter technology can be a solution to enhance the voltage rating and improve harmonic performance in many applications. Therefore, an application of a multilevel topology based on a direct ac–ac power converter is proposed in this paper. This paper first introduce the topology structure, the switching pattern grouping method, and the proposed output voltage modulation method for a five-level capacitor clamped multilevel matrix converter (5LMC). Amplitude coefficient adjustment is also introduced as a part of modulation procedure to simplify the duty cycles calculation. Simulation from MATLAB/Simulink is given to demonstrate the theoretical work. Experimental results from a five-level matrix converter prototype are presented to validate the theoretical findings. [ABSTRACT FROM AUTHOR]

A new active-clamped zero-voltage switching (ZVS) push–pull converter is proposed in this paper. Compared with the conventional push–pull converter, one auxiliary switch $Q_{{3}} and a clamping capacitor Ca are added in the primary side of the transformer to recycle the energy stored in the leakage inductors and clamp the voltage spike. Owing to the proposed converter which maintains ZVS of all the three switches from full load to very light-load condition, switching losses are reduced significantly. The voltage across the switch can be clamped at the input voltage plus the clamping capacitor voltage, i.e., V\rm{in}{+}VCa, are much less than those of a conventional push–pull converter that enabling the use of low-voltage, low-performance, and low-cost devices. In addition, the proposed topology can eliminate the problems of flux imbalance existing in the conventional one. Detailed operation, analysis, design, comparative study, and experimental results for the proposed converter are presented in this paper. An 800 W prototype was developed in the laboratory to evaluate and demonstrate the validity of the converter. [ABSTRACT FROM AUTHOR]

This paper proposes a multilevel high-frequency-link dc transformer (MDCT) based on dual active phase-shift principle for medium-voltage dc (MVDC) power distribution application. The proposed MDCT employs multilevel and multiplex conversion principle, which brings many advantages and makes the operation of MDCT quite different with the traditional dc transformer (TDCT) and modular multilevel converter. Compared to the TDCT scheme, the proposed MDCT has smaller circulating current and higher power factor; it can operate as a dc breaker to cutoff the connection with the MVDC distribution grid absolutely when a short fault occurs in the distribution grid; the redundant design can be achieved when some submodules failure to improve the reliability. In the paper, the topology, operation principle, modulation method, switching characterization, voltage, and power characterization, and control strategy of MDCT are presented and analyzed comprehensively. At last, a MDCT prototype is built and the experimental results verify the correctness and effectively of the proposed solution. [ABSTRACT FROM PUBLISHER]

A family of bidirectional switched-capacitor (SC) converters with high-gain ratio of any positive integer is proposed in this paper for distributed energy resources applications. As compared with other existing SC converters achieving a same conversion gain, the main advantages of the proposed converters are that they require a relatively lower number of switches and capacitors, have a relatively lower switch's and capacitor's stress, and that their associated driver circuits are simpler to realize. Importantly, with the achievable conversion ratio being flexible and that the input and output of the proposed converters are of common ground, the proposed converters are widely suitable for many applications. Moreover, as the proposed converters do not possess magnetic component or any component that can severely degrade the converters’ performance at high temperature, they are especially useful for high-temperature applications. Besides, the proposed converters are capable of delivering bidirectional power, which is a key requirement for emerging applications with battery storages. Different aspects of the proposed converters, including a simple auxiliary power supply circuit for the MOSFETs’ drivers, will be discussed in this paper. A nine-time SC converter prototype that operates with 20-V input voltage, 100-W output, and at 75 kHz, is constructed and tested. Experiment results show that the maximum efficiency achievable with this prototype is over 98% (without driver's loss) and the efficiency over the entire load range between 25 and 100 W is over 95.5% including the driver's loss. The output voltage ripple of the SC converter is less than 1%. When the SC converter is open-loop controlled, the load voltage regulation is relatively well kept at less than 5% between full load and no load conditions. [ABSTRACT FROM PUBLISHER]

To achieve the highest possible grade for server or computer power supplies in terms of efficiency, various solutions for high line input already exist on the market. In this paper, a new topology is investigated closely, showing that the titanium grade may be achievable at low line input with traditional silicon devices by the utilization of low voltage mosfets, which have an excellent figure of merits, by connecting two converter stages in parallel for low line input or in series for high line input. This paper presents simulation results which are verified with measurements from a developed prototype for 1 kW of power and 12 V output consisting of a triangular current mode power factor correction followed by a well-known phase shifted zero voltage switched bridge. Furthermore, a detailed description of the loss estimation by simulation, enhanced with additional calculations, is presented. [ABSTRACT FROM AUTHOR]

Soft switching is required to attain high efficiency in high-frequency power converters. Piezoelectric-transformer-based converters can benefit from soft switching in terms of significantly diminished switching losses and stresses. Adequate dead time is needed in order to deliver sufficient energy to charge and discharge the input capacitance of piezoelectric transformers in order to achieve zero-voltage switching. This paper proposes a method for detecting the optimum dead time in piezoelectric transformer-based switch-mode power supplies. The provision of sufficient dead time in every cycle of the switching period results in the quick start-up of resonant current inside the transformer. The new method is implemented by dynamically detecting the optimum dead time for each resonant cycle and results in reduced energy loss and, consequently, increased efficiency in the converter during initialization time and steady-state operation. The theory of optimum dead time operation is also discussed in this paper. Experimental results and simulation are provided to show the implementation of the concept. [ABSTRACT FROM AUTHOR]

This paper presents a method for generating a multilevel dodecagonal voltage space vector structure using a single dc source for induction motor drives. Multilevel dodecagonal structure combines the advantages of both multilevel and dodecagonal structures, and hence, generates low dv/dt phase voltage along with the elimination of fifth- and seventh-order harmonics over the entire modulation range. This eliminates low-order harmonic currents and prevents the generation of sixth-order torque ripple in the motor. The topology used requires only one dc source making four-quadrant operation of the drive system simpler compared to previously proposed multilevel topologies generating dodecagonal space vector structures. The topology used consists of a three-level flying capacitor (FC) inverter cascaded with a capacitor fed H-bridge. The FC inverter operates at a lower switching frequency and the low-order harmonics are eliminated by the switching action of the cascaded H-bridge inverter. The capacitors in the cascaded H-bridge modules are maintained at a substantially smaller voltage compared to the dc-link voltage and are inherently balanced during the pulsewidth modulation operation. This results in low switching loss, in the FC inverter as well as in the cascaded H-bridge inverter. Experimental results are included to validate the operation of the topology and modulation scheme presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a modular multilevel converter (MMC) topology for high-voltage dc (HVdc) system applications. The proposed MMC employs two half-bridge converters, a cascade of networks that consist of electronic switches, and multiple capacitors. Thus, charged capacitors are inserted in series with the arm current path, for a desired level of the output ac voltage. The switches that must be turned on are judiciously selected for the most efficient current path. The proposed MMC also offers dc-side fault handling capability. The paper compares the proposed MMC with the half-bridge submodule-based MMC, full-bridge submodule-based MMC, and clamp-double submodule-based MMC technologies. It is shown that the proposed MMC is more efficient than the three aforementioned MMC technologies, while it offers the same fault handling capability as that of an equivalent full-bridge-based MMC. Time-domain simulation studies confirm the effectiveness of the proposed MMC under various normal and faulted operating scenarios, using detailed as well as reduced models. [ABSTRACT FROM AUTHOR]

This paper presents a digital control technique to achieve valley switching in a bidirectional flyback converter used to drive a dielectric electroactive polymer-based capacitive incremental actuator. This paper also provides the design of a low input voltage (24 V) and variable high output voltage (0–2.5 kV) bidirectional dc–dc flyback converter for driving a capacitive incremental actuator. The incremental actuator consists of three electrically isolated mechanically connected capacitive actuators. It requires three high-voltage (HV) (2–2.5 kV) bidirectional dc–dc converters to accomplish the incremental motion by charging and discharging the capacitive actuators. The bidirectional flyback converter employs a digital controller to improve the efficiency and charge/discharge speed using the valley switching technique during both charge and discharge processes, without the need to sense signals on the output HV side. Experimental results verifying the bidirectional operation of a HV flyback converter are presented using a 3-kV polypropylene-film capacitor as the load. The energy-loss distributions of the converter are presented when 4- and 4.5-kV HV mosfets are used on HV side. The flyback prototype with a 4 kV mosfet demonstrated 89% charge energy efficiency to charge the capacitive load from 0 V to 2.5 kV, and 84% discharge energy efficiency to discharge it from 2.5 kV to 0 V. [ABSTRACT FROM AUTHOR]

In this paper, a nonisolated two-channel light-emitting diode (LED) driver with automatic current balance and zero-voltage switching (ZVS) is presented. In this LED driver, a dc-blocking capacitor is connected with one side of the coupled inductor. Therefore, based on the ampere–second balance, a current source is generated with the average value of the positive current identical to the absolute average value of the negative current. Accordingly, the LED currents can be balanced naturally without extra active components or current sharing transformer. Consequently, the circuit components can keep at a low count. In addition, the proposed LED driver can achieve ZVS turn-on. Thus, the switching loss can be decreased. Above all, the proposed two-channel LED driver can be extended to a multichannel LED driver. In this paper, detailed theoretical analyses and experimental results are provided to verify the feasibility and effectiveness of the proposed LED driver. [ABSTRACT FROM AUTHOR]

In this paper, the Z-source converter is introduced to power factor correction (PFC) applications. The concept is demonstrated through a wireless power transfer (WPT) system for electric vehicle battery charging, namely Z-source resonant converter (ZSRC). Due to the Z-source network (ZSN), the ZSRC inherently performs PFC and regulate the system output voltage simultaneously, without adding extra semiconductor devices and control circuitry to the conventional WPT system such as conventional PFC converters do. In other words, the ZSN can be categorized as a family of the single-stage PFC converters. In addition, the ZSN is suitable for high-power applications since it is immune to shoot-through states, which increases reliability and adds a boost feature to the system. The ZSRC-based WPT system operating principle is described and analyzed in this paper. Simulations and experimental results based on a 1-kW prototype with 20-cm air gap between the system primary and secondary sides are presented to validate the analysis and demonstrate the effectiveness of the ZSN in the PFC of the WPT system. [ABSTRACT FROM PUBLISHER]

Various magnetically coupled impedance source (MCIS) networks have been proposed in the literature for increasing voltage gain and modulation index simultaneously while reducing the number of passive components used in the converter. However, applications of such networks have been limited by their discontinuous currents drawn from the sources and/or high stresses experienced by their components. This paper thus proposes three new MCIS networks named, respectively, as quasi-Y-source, quasi-Γ-Z-source, and quasi-T-source or quasi-trans-Z-source networks. These new networks inherit all advantages of the existing MCIS networks. In addition, they demonstrate advantages like continuous input currents, reduced source stresses, and lower component ratings that are not achievable by other existing networks. Further, dc-current-blocking capacitors used in the networks help to avoid saturation of magnetic core. Derivations of all two-winding MCIS networks, including existing and new networks, from the generalized three-winding MCIS networks are then systematically illustrated, before comparing them. Operational principles, mathematical derivations, simulation, and experimental results of all studied networks have been presented in the paper. [ABSTRACT FROM PUBLISHER]

Modular multilevel converters (MMCs) are being developed for the grid connection of offshore wind or tidal farms. In order to reduce the construction and maintenance costs, it is desirable to reduce the weight and volume of the system. In current MMC submodule designs, the reservoir capacitor usually accounts for over 50% of the total volume and 80% of weight. This paper presents a new design concept and control principle for a submodule using the stacked switched capacitor (SSC) architecture that can significantly reduce the capacitor size in an MMC. Practical considerations for a high-voltage high-power SSC-based MMC submodule are presented in this paper, through the design of a 21-level, 40-kV (pole-pole dc), 19.1-MW, grid-connected system, and the concept is demonstrated experimenttally on a scaled-down 400-V, 12.3-Apeak laboratory prototype submodule. It is shown that with the proposed SSC architecture, the total volume of capacitors in each submodule can be reduced by more than 40% without significantly increasing the power loss. [ABSTRACT FROM AUTHOR]

The paper proposes a method of active switching harmonics current reduction in the dc-link capacitor of a two-level, three-phase, back-to-back converter. Based on the derived analytical solution for switching harmonic currents in the dc-link, it is shown that by specific control over the pulsewidth-modulated (PWM) carriers’ phase angles, the targeted harmonics of the rectifier and the inverter can be synchronized in phase such that their cancellation occurs in the dc-link capacitor. This synchronization is provided by harmonic phase feedback control. A three-step procedure to implement the method is detailed in the paper. The effectiveness of the proposed approach is verified experimentally. [ABSTRACT FROM AUTHOR]

Aimed at the problem that the auxiliary commutation circuit (ACC) of auxiliary resonant commutated pole (ARCP) inverters has a high loss in commutation processes, this paper presents a novel modulation strategy with shunt dead time based on a double ARCP (DARCP) inverter. In comparison with the original modulation strategy, this modulation strategy cannot only achieve soft switching for all switches, but also avoid the superposition of resonance current and load current at commutation moments in double ACCs (DACCs) and make the maximum current through DACCs approximately equal to load current in commutation processes. So, the circulating current loss in DACCs and the current stress of auxiliary switches can be effectively reduced. According to the equivalent circuits in different operation modes under the novel modulation strategy, this paper analyzes the operation principle, soft-switching implementation condition, and optimal parameter design procedure of the DARCP inverter. Finally, a 10-kW–16-kHz DARCP inverter prototype with insulated gate bipolar transistor-based switches is built. Experimental results are given to demonstrate the validity and features of the DARCP inverter under the novel modulation strategy. [ABSTRACT FROM AUTHOR]

The low threshold voltage of Gallium Nitride enhancement mode FETs is a concern in synchronous dc–dc buck converters. This paper presents a converter using a gate drive with a negative biased gate voltage on the low-side FET to improve the dV/dt robustness. The resulting much larger voltage drop during the dead time conduction is a concern as it can quickly overcharge the bootstrap capacitor voltage. This paper demonstrates that with a negative biased gate voltage, the rise in the bootstrap capacitor voltage is predominantly caused by the change in effective dead time conduction due to a variation in output load. A spice model to estimate the change is presented and verified. This paper also found that a change in the bootstrap capacitor voltage must be prevented as it leads to a significant change in turn-on dynamics, resulting in higher dV/dt stress with an increase in output load. To prevent a change in bootstrap capacitor voltage, different techniques such as Zener diode clamping and an external free-wheeling Schottky diode are tested and discussed. Finally, a modification of a standard bootstrap circuit using a series inductor is proposed and tested. It has been found to be the most effective method in preventing a variation in the bootstrap capacitor voltage and should be included when using a negative gate drive in a GaN dc–dc buck converter. [ABSTRACT FROM AUTHOR]

This paper presents concepts and results of an investigation of power electronic thyristor-based switched-capacitor voltage multipliers (SCVMs). A concept of the SCVM power converters assumes the utilization of resonant circuits for the zero-current switching operation. The topology makes it possible to apply thyristors as active switches that create the possibility of composing the resonant switch-mode converters for high-voltage gain, high power, and low cost, and opens a huge area of applications. This paper presents an in-depth analysis of the SCVM configured as the resonant high-power thyristor-based converter. The operation with regard to the specific switching conditions of thyristors, as well as efficiency of the converter is analyzed providing the unique relationship important for the converter design, optimization, and efficiency improvement. An experimental validation confirms the feasibility and the operation concept of the SCVM and demonstrates the efficiency range. The SCVM converter can be optimized to the topology with a decreased number of switches. This paper also presents a novel topology of the resonant converter with a reduced number of switches, resonant switched capacitor voltage multiplier (RSCVM), dedicated for thyristor implementation. The RSCVM requires the specific component selection and control. The analysis of the configuration, operation, efficiency, and component selection of the RSCVM converter, as well as simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

This paper describes active shunt LC decoupling circuit with ceramic capacitors, allowing volume reduction and lifetime improvement of the high-voltage dc filters. Active filtering is based on the energy exchange between high-voltage coupling and low-voltage auxiliary capacitors. The coupling capacitor enables use of the low-voltage switched-mode power stage and low-voltage auxiliary decoupling capacitor. Advantageously, this allows to reduce power dissipation, switching frequency ripple current, and to reduce volume of the circuit. Additionally, power efficiency and capacitor lifetime are improved by using recent high-voltage coupling multilayer ceramic capacitors, reaching very low ESR. This paper provides description of the active decoupling capacitor, and shows an example of the feedback control. Obtained performances are demonstrated on the prototype of 1300-μF/450-V capacitor, allowing to reduce volume by three, when compared to ordinary 450-V electrolytic capacitor. [ABSTRACT FROM AUTHOR]

This paper presents a novel interleaved high-conversion-ratio bidirectional dc–dc converter based on switched capacitors and coupled inductors. Series-connected switched capacitor and inductor cells were used to increase the voltage conversion ratio, reduce voltage stresses on power switches, realize soft-charging/discharging of switched capacitors, and achieve autocurrent-sharing in parallel inductors. The interleaved structure combined with switched capacitors was adopted to reduce current ripple at the side having lower voltage, thus enabling applications that require high power levels. In this paper, we first review the status of high-voltage-ratio bidirectional dc–dc converters. Then, the evolution of the proposed extensible topologies and the steady-state operating principle under the inductor current continuous conduction mode is presented. Finally, the performance and features such as voltage gain, voltage and current stress, and the autocurrent-sharing mechanism that are realized by switched capacitors are verified; the optimal design of coupled-inductors, switched-capacitors, and the chip size of switches are given. A specific design of the driving circuit that facilitates actual applications is described. A 1-kW prototype converter, employing a hybrid configuration of SiC and Si mosfets, was constructed to verify the theoretical analysis, and achieved an optimal compromise between conversion efficiency and low cost. [ABSTRACT FROM AUTHOR]

Middle-point inductance ${{\boldsymbol L}_{{\boldsymbol {\text{middle}}}}}$ can be introduced in multiple-chip power module package designs. In this paper, the effect of middle-point inductance on switching transients is analyzed first using a frequency-domain analysis. Then a dedicated multiple-chip power module is fabricated with the capability of varying ${{\boldsymbol L}_{{\boldsymbol {\text{middle}}}}}$ , and extensive switching tests are conducted to evaluate the middle-point inductance's impact. Experiment result shows that the active mosfet's turn-on loss decreases at higher values of ${{\boldsymbol L}_{{\boldsymbol {\text{middle}}}}}$ , while its turn-off loss increases. Detailed analysis of this loss variation is presented. In addition to the switching loss variation, it is also observed that different peak voltage stresses are imposed on the active switch and antiparallel diode during the switching transients. Specifically, in the case of lower mosfet's turn-off, the maximum voltage of the lower mosfet increases as ${{\boldsymbol L}_{{\boldsymbol {\text{middle}}}}}$ goes up; however, the peak voltage of the antiparallel diode decreases significantly. The induced voltage spikes during upper mosfet turn-on process is also evaluated, and an opposite trend is observed experimentally. Analysis of the voltage overshoot variation is discussed. Based on the experimental evaluation and analysis, a multiple-chip power module package design guideline is summarized considering the middle-point inductance's effect. [ABSTRACT FROM AUTHOR]

This paper proposes a novel modular equalization architecture for series-connected electric double-layer capacitor (EDLC) modules, each consisting of multiple cells connected in series. Cell voltages in a module are equalized by an inductive voltage divider (IVD)-voltage multiplier (VM)-based cell equalizer, while module voltages are unified by switched capacitor converters (SCCs). Square wave voltages generated at switching nodes of the IVD-VM-based cell equalizers are utilized to drive the SCC-based module equalizers, realizing the switchless topology of SCC-based module equalizers. The required switch count of the proposed system can be halved compared to conventional systems, allowing simplified circuit. An experimental equalization test for three EDLC modules, each consisting of six cells in series, was performed from an initially voltage-imbalanced condition. Module and cell voltages were equalized at different rates, and the equalization performance of the proposed modular equalization system was successfully demonstrated. [ABSTRACT FROM AUTHOR]

Electrolytic capacitors are often needed to provide the high-density energy storage required by ac-powered LED drivers; however, they are also well known for their short lifespans. Eliminating electrolytic capacitors in ac–dc LED driver design has become a very important target to improve LED driver technology. In this paper, a cycle-by-cycle energy buffering LED driver has been proposed to achieve electrolytic capacitor-less flicker-free operation. An energy buffering unit, with high-voltage film capacitors being the energy storage device, is introduced in the design to buffer the imbalanced energy in every switching cycle. The switching current can be controlled to meet high power factor correction requirement, while maintaining dc LED output current at the same time. Compared to previous electrolytic capacitor-less designs, this technology can reduce circulating power and, therefore, power conversion loss. A 15-W experimental prototype had been built and tested to verify the proposed LED driving method. [ABSTRACT FROM AUTHOR]

A new boost-type multilevel inverter using switched capacitor structure is proposed. The main feature of the proposed inverter is boosting and multilevel output with small number of components. Due to the passive voltage balancing of each capacitor maintains a constant voltage without additional control. In this paper, the operation principle, the modulation method, the voltage/current stresses on switches and the determination of capacitances, the simulation results with MATLAB/Simulink R2015a, the experimental results, and the 2-kW simulation are shown. The simulation and the experiments were conducted under resistive load and inductive load conditions. In addition, the load variation was conducted in the experiment. Under both resistive load and inductive load conditions, the obtained waveforms by simulation and experiment agreed well with the theory. In the load variation experiment, the obtained waveforms were not distorted and the capacitor voltages maintained constant. [ABSTRACT FROM AUTHOR]

Online monitoring is an inevitable necessity for dc–dc converters in industrial applications to achieve a fault-tolerant structure, which ensures reliable operation and prevents catastrophic failures. In this paper, a comprehensive monitoring system is proposed for non-isolated dc–dc converters. The proposed approach is mainly focused on monitoring the most prone to failure components of these converters including switching devices and capacitor. Using the proposed monitoring system, switch/diode open circuit and short circuit faults are detected in less than one switching cycle. Furthermore, online monitoring of the capacitor equivalent series resistance and switch on-state voltage as effective precursors of aging is also carried out. Finally, an inter-turn fault detection technique is presented for the converter inductor. The mentioned monitoring tasks are accomplished using only two electrical sensors (for capturing voltages across the converter diode and inductor) and two temperature sensors. The presented monitoring approach is simple, cost-effective, easy to implement, and applicable for all non-isolated dc–dc converters including buck, boost, and buck-boost converters. Performance of the monitoring system is evaluated by considering different scenarios in the experiments carried out on a laboratory prototype. The results confirm the effectiveness of the proposed system for fault diagnosis and aging monitoring in non-isolated dc–dc converters. [ABSTRACT FROM AUTHOR]