Search

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

A new single stage three-phase ac–dc converter with four switches and galvanic isolation is proposed in this paper. The new converter is simple and uses fewer switches than previously proposed ac–dc converters of the same type. It is a bridgeless converter that can operate with continuous input current and with any pulsewidth modulated method suitable for a standard three-phase six-switch voltage source rectifier. In this paper, the operation, control, analysis, and design of the proposed converter are explained and its features are discussed. Experimental results obtained from a prototype that confirm the feasibility of the converter are presented as well. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper investigates a Vienna rectifier as a charger for series-connected battery packs. Focusing on carrier-based pulsewidth modulation (CBPWM), the ripple current flowing through the neutral point (NP) results in the voltage oscillation if the loads are resistive. To reduce the ripple of average NP current with mitigated distortion under balanced and unbalanced dc-link voltages conditions, a novel CBPWM with segmented component injection scheme (SCIS) is proposed in this paper. After dc component injection, continuous intervals for optimized component injection and clamping intervals for compensation component injection are identified. Optimized components are calculated originally based on unbalanced factor to make the average NP current zero-size in one switching period. Moreover, unique compensation components generate suitable NP current to shape the sinusoidal input currents according to the circuit analysis. In consequence, the SCIS not only keeps the input current with low-harmonic distortion, but also minimizes the oscillation of dc-link voltage under balanced and unbalanced conditions. In addition, the value of the NP current during the clamping intervals is analyzed under various operating conditions. The effectiveness and the performance of the proposed SCIS are verified by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

The six-phase asymmetrical induction motors (SPIMs) are employed for high power medium voltage drive due to its attractive features of reduced stator copper loss, lower torque pulsation, higher torque per ampere, and higher reliability. In this paper, analysis of carrier-comparison-based pulse width modulation (PWM) techniques namely sinusoidal PWM and double zero-sequence injection PWM are carried out from a space vector perspective. Furthermore, new space vector pulsewidth modulation (SVPWM) techniques are developed by modifying the switching sequences of carrier-based PWM techniques. A comprehensive analysis of these PWM techniques is carried out in terms of harmonic flux trajectories, squared harmonic flux, and harmonic distortion factor (HDF). As a result, modified SVPWM technique namely 6ΦSVM3 is found superior to aforesaid PWM techniques, which significantly reduces HDF and provides lower current total harmonic distortion (THD). The experimental results of aforementioned PWM techniques are obtained and verified from six phase asymmetrical induction motor fed by dual two-level 3ΦVSIs. This paper is also accompanied by a video file of experimental test setup recorded while 6ΦSVM2 is running on SPIM. [ABSTRACT FROM AUTHOR]

Inductor current is an important feedback parameter in synchronous buck converters (SBCs). It is used for overcurrent protection, current sharing among interleaved modules, and current-mode feedback regulation, among others. While implementing a digital controller, inductor current is sensed and fed into the controller through a high sampling frequency analog to digital converter (ADC). As the switching frequency of the converter becomes higher, the need for an even higher sampling frequency ADC also goes up, which is a distinct disadvantage in terms of the overall cost. This paper discusses a simple current estimation technique that avoids use of any expensive current sensor and high sampling frequency ADCs. The paper shows that in a buck converter, inductor current can be estimated by tracking the width of the switch node voltage. Implementation and limitations of the proposed current estimation scheme are discussed in detail. The proposed method is validated using a 3.3 V–15 A SBC prototype and results show the estimation technique is accurate within 5% with a converter switching frequency of 800 kHz. In order to prove the effectiveness of the technique in feedback regulation, the current estimation technique is used to implement average current mode and hysteretic current mode control on a SBC. To prove the effectiveness of the proposed current estimation scheme, it is used in closed-loop control of the SBC to verify the dynamic responses, such as start-up transient, step change in load, and reference. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

This paper presents a new six-level flying capacitor based (FC-based) multilevel converter with one dc source and the capability of operating in all power factors and modulation indexes. Multilevel converters with one dc voltage source are attractive in many applications as they do not need rather expensive and bulky multiwinding input transformer connection at the dc side. On the other hand, not all classic multilevel converters with one dc source can produce any desirable number of output voltage levels at all power factors and/or modulation indexes. In this paper, a hybrid structure is proposed in which six voltage levels can be realized at the ac terminals. The modulation technique and the control strategy for the FC voltage balancing are presented. To show the advantages of the proposed converter, different performance criteria, such as switch count and rating, the size of capacitors, switching frequency, and power losses, are compared with other existing six-level topologies. The results indicate that the proposed structure is superior to other six-level converters from different standpoints. Simulation results are used to further evaluate the performance of the proposed converter. A laboratory-type experimental setup is used to validate the theoretical results. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper proposes a novel discontinuous pulse-width modulation (DPWM) method to reduce the current harmonics and improve the system efficiency for a single-phase three-level neutral-point clamped inverter. In single-phase inverters, the unipolar pulse-width modulation (UP-PWM) method is commonly used. However, this method has the disadvantage of power losses due to numerous switching operations. Conventional DPWM methods reduce the power losses and improve efficiency but increase the current total harmonic distortion (THD). To overcome these weaknesses, this paper proposes a hybrid DPWM switching method combining two PWM methods: the UP-PWM method and the conventional DPWM method called one-pole clamped PWM method. Since the proposed DPWM method offers all the advantages of both PWM methods, the optimal performance—with regard to the power losses and current THD—is obtained. The combination of two PWM methods is investigated by analyzing the power losses and current THD. Based on the analysis, the process determining the optimal operating condition is introduced. The effectiveness of the proposed DPWM method is demonstrated through simulations and experiments. [ABSTRACT FROM AUTHOR]

The output voltage of power electronic converters is a very important quantity for dynamic control of power electronic systems. In electrical drives without electromechanical position or speed sensor, the terminal reference voltage is used to obtain the rotor position. Dead-time effects and semiconductor voltage drop lead to distortion in the actual output voltage and degrade the control performance when the back electromotive force magnitude is low. Thus, for stable low-speed operation, output voltage sensing becomes necessary. Due to the switching nature of power electronic systems, this is not a trivial task, especially when instantaneous measurement of the terminal voltage is required. In this paper, an instantaneous switching-period average voltage sensing technique is proposed that utilizes a combined approach of oversampling and filtering. Based on the theoretical analysis of the sampling- and filter-induced measurement distortion, a general solution for an optimal filter design is derived. The additional sensing circuit is integrated into the low-side gate driver of the converter outputs. This paper includes details about the hardware implementation and extensive verification measurements. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a novel six-pulse low-frequency (LF) fluctuating high-voltage dc-bus-based power system architecture for fuel cell vehicles (FCVs) application. A novel hybrid modulation scheme consisting of six-pulse modulation at LF scale and modified secondary modulation and 33% pulse width modulation at high-frequency (HF) scale is proposed. Three-phase ac waveforms for the propulsion system of FCVs are generated from LF fluctuating high-voltage dc bus. The proposed modulation technique significantly reduces the switching losses of the bidirectional dual-stage inverter: 1) soft-switching of both sides of the front-end current-fed full-bridge converter is realized; and 2) at any moment, only one leg of back-end three-phase inverter is switched at HF, while the other two legs are kept in on or off states. This tremendously reduces the bidirectional inverter's switching losses and improves the system efficiency. The LF fluctuating high-voltage dc bus allows the elimination of large electrolytic dc-link capacitor, which contributes to a more reliable and compact design. This paper presents the operation, analysis, and design of a bidirectional inverter implementing the proposed hybrid modulation technique. Simulation results obtained from power electronics simulation software PSIM and experimental results from the lab prototype clearly validate the effectiveness of the proposed modulation technique. [ABSTRACT FROM PUBLISHER]

Common-mode voltage output is closely associated with switching states in three-phase three-wire neutral point clamped converter. Detailed analysis shows avoiding redundant states can effectively improve the common-mode voltage, so this paper proposes a pulse width modulation (PWM) technique with zero redundant state to reduce the common-mode voltage output, and evaluates their performance with the conventional PWM schemes. This paper also takes the compensation of neutral point potential deviation into consideration. Laboratory test results are presented to verify the effectiveness of the proposed scheme. [ABSTRACT FROM PUBLISHER]

This paper proposes an active switching harmonic current reduction method within the dc-link capacitor of two-level, three-phase, back-to-back converters. This method is based on the derived analytical solution for switching harmonic currents in the dc-link. It is shown that by controlling the pulse width modulation carrier waveform's phase angles, the harmonics in the second carrier band of the rectifier and the inverter can be synchronized such that cancellation occurs in the dc-link capacitor. This synchronization is provided by harmonic phase feedback control. The feasibility of the proposed approach has been verified experimentally and results are presented in this paper. [ABSTRACT FROM PUBLISHER]

The modeling and control of a buck–boost and stacked dual half-bridge (DHB) integrated bidirectional dc–dc converter have been studied in this paper. This converter features high-voltage transfer ratio, high efficiency, and the minimum number of switches. In this paper, an extended, continuous, full-order, state-space averaging modeling method is proposed. Compared with existing methods, the proposed method exhibits higher coincidence with the switching circuit simulation, in steady and especially dynamic states. Due to its high dynamic accuracy and low complexity, the proposed modeling method provides a better theoretical analysis and a fast simulation tool for transient process and control design of converters with dual-active-bridge units, especially with DHB units. By using this method, the high-frequency transformer series inductance current is directly divided into a sampled dc component and a fluctuant component. Only the sampled dc one is included into state variables, but both components are considered into state equations. Besides, this method regards the entire converter as a linear superposition of its subsections, which provides a stepwise modeling based on linearization of subsections. Moreover, a decoupled proportional-integral control method is proposed to enhance the stability and dynamic response of the converter. This control method is analyzed by the proposed models, which can be regarded as an application of the proposed modeling method. Simulation and experiments have validated both the proposed modeling and the decoupled control strategy. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) with nearest level modulation (NLM) is widely used in the high voltage applications for low switching frequency and easy implementation. Existing literature has not provided a complete submodule (SM) fault ride-through scheme for MMC with NLM. In this paper, a strategy including fault detection, localization, redundancy, and recovery is proposed to ensure continuous operation of MMC under IGBT open-circuit faults conditions. It only requires a few hardware and software resources. The features of MMC and SMs with three types of failures are studied, respectively. Based on these, the fault detection method is proposed by using a simple hardware circuit, thus high computation complexity is avoided. Since current fault localization schemes are limited to MMC with carrier phase shifted pulse width modulation, this paper further proposes a strategy for MMC with NLM to locate the faulty SM and identify the fault type. After this, the fault redundancy and the proposed fault recovery method are applied to eliminate the fault and then exit the failure state. Therefore, the ability of SM fault ride-through can be realized. Analysis of failure characteristics are verified in simulation. Experimental results based on a single-phase MMC prototype with 11 SMs per arm are presented to demonstrate the validity of the proposed fault ride-through strategy. [ABSTRACT FROM AUTHOR]

This paper presents a new feed-forward strategy for suppressing low-order harmonic circulating currents in pulsewidth-modulated (PWM) based modular multilevel converters (MMCs). The approach is based on the new average model approach established in this paper, which identifies cross-coupling interactions between the system-level and submodule elements using decomposed dependent sources. As well as improving the damping of the system, the major advantage of this approach is that it maintains the natural DC bus balance property of a PWM modulated MMC by considering the upper and lower arms together (unlike existing feed-forward schemes which treat each MMC arm independently). Moreover, unlike existing direct control resonant strategies, which require careful gain tuning and are highly dependent on the ac system frequency, the proposed approach achieves wideband circulating current ripple suppression without requiring knowledge of the circulating current harmonic frequencies and needs only a simple proportional–integral (PI) controller to regulate the circulating current dc component for power balance. This makes it particularly suitable for use in multifrequency or variable-frequency ac systems. Extensive simulation and matching experimental results, including steady-state and transient responses compared against existing circulating current suppression approaches, validate the effectiveness and benefits of this new feed-forward compensation technique. [ABSTRACT FROM PUBLISHER]

The performance of modular multilevel converters (MMCs) in medium-voltage applications, where the number of required submodules is not high, can be improved utilizing low switching frequency modulations such as (2N+1) selective harmonic elimination-pulse width modulation (SHE-PWM), which provides tight control of lower order harmonics and low switching losses. This paper proposes a calculation method, which is based on a novel formulation, to solve the SHE-PWM problem. In particular, MMCs with (2N+1) phase output voltage levels are considered, obtaining a (2N+1) SHE-PWM waveform. This method utilizes a unique system of equations that is valid for any possible waveform. Therefore, it is able to calculate simultaneously, without predefined waveforms, both the switching patterns and the associated firing angles that solve the (2N+1) SHE-PWM problem. Consequently, the search process is simplified and optimized. Furthermore, this paper also proposes a circulating current control technique, which can be applied along with (2N+1) SHE-PWM without disturbing the phase output voltage. Simulation results and experimental tests obtained with a single-phase laboratory prototype prove the validity of the novel (2N+1) SHE-PWM implementation method and the proposed circulating current control technique. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid seven-level converter based on T-type converter and H-bridge cascaded suitable for low-voltage and high-power-density applications. The operation principles and conduction paths are analyzed comprehensively. Voltage balance control of the floating capacitors is the key point of this paper. Mathematical expressions of capacitor voltage balance conditions are deduced based on sinusoidal pulse width modulation (SPWM). The results show that floating capacitor voltages are only balanced when the modulation index is below 0.82 under SPWM. In order to enlarge the modulation index ensuring the capacitor voltage balance, space vector modulation (SVM) is also applied to regulate floating capacitor voltages taking advantage of redundant switching vectors. Meanwhile, in SVM, there are no additional control requirements for the capacitor voltage. Taken both SPWM and SVM into consideration, the limit to the range of operation for this seven-level converter is presented, which is a function of the modulation index and the power factor. The merit of dc voltage utilization improvement in this topology is also analyzed based on simulation results. Simulations and experimental results under different modulation index and RL load are presented to verify the modulation strategies illustrated in this paper. [ABSTRACT FROM PUBLISHER]

This paper targets the reduction of common-mode voltage in an indirect matrix converter (IMC) through an intelligent space-vector-based modulation technique. This mode of control results in lower dV/dt at the motor terminals, thereby, reducing voltage stress to windings; and reduced output voltage distortion resulting in lower machine losses. The conventional indirect space vector pulse-width modulation method of controlling matrix converters involves independent control of either the rectifying stage or the inverting stage of the converter. However, in this paper, by suitable selection of space vectors, the rectifying stage of the matrix converter generates different levels of virtual dc-link voltage. Therefore, the responsibility of formulating output voltages with a particular magnitude and frequency, which can be translated to different machine speeds, has been transferred solely to the rectifying stage of the IMC. Estimation of the degree of distortion in the three-phase output voltage is another facet discussed in this paper, which aids the sizing and designing of output passive filters. The analysis of output voltage distortion and the proposed modulation strategies have been substantiated by simulations in MATLAB/Simulink and experimentally verified on a scaled down laboratory prototype. [ABSTRACT FROM AUTHOR]

Wide bandgap semiconductor switches have been increasingly utilized to improve the power density and efficiency of power converters, as such devices are able to operate at very high frequencies, e.g., up to 100 MHz, with reduced power losses. However, such a high-frequency operation may impose a challenge to the digital control system, and the system clock frequency should be up to 100 GHz in high-precision applications, which is difficult to realize in low-cost microprocessors. Instead of using extremely high-frequency clocks, preprocessing-based solutions that utilize digital pulse-width-modulated (DPWM) dither techniques can also enhance the DPWM resolution with moderate frequency clocks. Unfortunately, this is usually achieved at the expense of introducing low-frequency harmonics, which may complicate system controller and output filter design. In this paper, an optimal dither technique is proposed to enhance the resolution of DPWM power converters. The concepts of positive dither and negative dither are first proposed in this paper. Furthermore, vector-diagram-based analysis indicates that with proper utilization of positive dithers and negative dithers and carefully selected dither sequences, the lowest order harmonic introduced by the conventional dither technique can be completely eliminated when the dither period is multiples of six switching periods. In other cases, the proposed optimal dither technique can produce minimized lowest order harmonic. Finally, experimental results obtained from a Gallium Nitride (GaN) devices-based synchronous buck converter validate the feasibility of the proposed dither technique. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel five-level nested neutral point piloted (NNPP) converter and analyzes the operating principle of five-level NNPP converter. This paper presents a novel space vector pulse width modulation (SVPWM) algorithm based on gh coordinate for five-level NNPP converter. First, the common-mode voltage is reduced by choosing the appropriate redundant switching states. After that, the floating-capacitor voltage balance control strategy is presented. The appropriate switch combinations of each phase are determined by the control requirements of floating-capacitor voltages respectively and the hardware mapping method of the switching states is presented. Furthermore, the neutral-point voltage balance control strategy is presented. In order to balance the dc-link capacitor voltages, the seven-segment switching sequence is selected according to the control requirements of dc-link capacitor voltages and the neutral-point voltage regulatory factor is introduced to regulate the durations of the redundant switching states in a switching cycle. Finally, the validity of the novel SVPWM algorithm with decoupling control strategies of floating-capacitor voltages and dc-link capacitor voltages is verified by the experimental results of five-level NNPP converter under steady-state and dynamic conditions. [ABSTRACT FROM AUTHOR]

This paper analyzes three different carrier-based modulation patterns applied to a three-phase high-power-factor-corrected (PFC) five-level buck+boost-type converter acting as an interface between dc distribution systems and an ac grid. The modulation is analyzed employing the space vectors theory so that the achievable performance is demonstrated. The main advantage of the analyzed modulation strategy is its simplicity, which makes it suitable for digital signal controller (DSC) implementations. This seems straightforward for voltage source converters, but is a challenge for current-multilevel converters that typically employ field-programmable gate array devices to achieve better harmonic distortion performance. This is due to modern power electronics DSCs being typically designed for other converter topologies. The power converter is constructed with two phase-shift-modulated six-switch buck-type PFC converters, paralleled by interphase transformers, and an inverting circuit. The system features: bidirectional current carrying capability; relatively low parts count; high utilization of the semiconductors; and low current and voltage ripple at its terminals. The principle of operation, detailed description, analysis of the modulation strategy, and dimensioning equations for three different power circuit realizations are described in this paper assuming the analyzed modulation patterns. The feasibility of the presented converter is demonstrated by means of a constructed hardware prototype. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

Battery energy storage system based on the modular multilevel converter (MMC-BESS) is able to realize the decentralized management of battery packs, which is suitable for the retired battery utilization to improve the efficiency of battery recycling. With multiple submodules (SM), the corresponding SM fault ride-through method is mandatory to improve operational reliability. This paper proposes a redistributed pulsewidth modulation method for MMC-BESS to ride-through the SM fault through employing the simple logic operation, which could avoid the unexpected carrier shift under various modulation indexes induced by the SM fault or grid voltage rise. MATLAB simulations and experimental results are presented to verify the performance of the proposed method. [ABSTRACT FROM AUTHOR]

In photovoltaic applications, many previous research works have focused on pulsewidth modulation (PWM) resonant converters in order to achieve a high efficiency with a wide input voltage range. Conventional approaches utilized symmetric boosting modulation at the secondary side rectifier to obtain a symmetric operation, and they utilized two boosting modes in a switching period. Among various rectifier structures, the voltage doubler structure has a strong advantage due to a small number of components. However, it suffers from serious hard switching losses in the secondary side rectifier. In this paper, a new converter with a novel asymmetrical modulation is proposed and verified. The strong point of the proposed converter is that it eliminates hard switching turn-on losses from the rectifier, while maintaining the minimized number of components. Although the proposed converter adopts an asymmetric modulation, the offset current on the transformer becomes zero inherently. Furthermore, a “forced half resonance” operation of the proposed converter keeps rms current stresses at the same level as conventional converter although it has a higher peak current. Accordingly, the proposed converter achieves a superior efficiency with the minimum number of components at 35–25 V input and 380 V/300 W output specification. [ABSTRACT FROM AUTHOR]

Three-phase current reconstruction techniques with a single current sensor have been studied for permanent magnet synchronous machines (PMSMs) drive system due to its reducing cost and volume. In order to minimize the current reconstruction dead zone in the conventional method with a single dc-link current sensor, a strategy to couple multiple available positions through the single current sensor is proposed in this paper. With the proposed method, two independent equations of the stator currents can be obtained by sampling the single current sensor twice in both zero voltage vectors and active voltage vectors. By solving these two equations, the phase current reconstruction can be achieved accurately, which moves the current reconstruction dead zone toward six corner area of the space vector hexagon. Meanwhile, in order to guarantee the proposed method suitable in the whole linear modulation region, the suitable selection of the pulsewidth modulation switching period is analyzed in detail. Furthermore, the optimal selections of multiple sampling positions are discussed to lower the actual implementation difficulty of the proposed method. Finally, the experimental results on the PMSM demonstrate that the reconstructed phase currents with the proposed method can be always in consistent with the actual measured currents under different working conditions. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

As research in matrix converters (MCs) has progressed over time, space vector modulation has emerged as the most popular technique for their modulation. Lately, model predictive control (MPC) has also been explored for the modulation and control of MCs, primarily gaining popularity due to the ease in realization of multiple objectives, as desired in MCs. However, multi-objective MPC employs assignment of weights to each control objective, wherein weight tuning is either empirical in nature or computationally cumbersome. This paper proposes a new modulation technique for MCs, inspired from delta sigma modulation for voltage source converters, that can be used for load voltage and source current control of MCs. Since source currents are samples of the load current envelope, it is required that this envelope be known for the control of source current. To eliminate load current sensors, predictive model of the load is used in envelope estimation. Further, independent switching schemes are generated for each objective, and an error minimization approach is used in integrating the two schemes into a final state selection, hence eliminating weighing factors. Unlike MPC, error predictions for all states of MCs, are not needed, hence facilitating easier implementation without significant processor burden, besides ensuring the quality of response. [ABSTRACT FROM AUTHOR]

A novel PWM full bridge (FB) dc–dc converter for large power industrial applications is proposed in this paper. The soft switching mode of the primary switches can be varied under different input and output conditions to achieve optimum system efficiency. In the zero-voltage and zero-current switching (ZVZCS) mode, the turn-on and turn-off switching loss can be optimized because the soft switching conditions of the turn-on and turn-off instants are well decoupled. In the zero-voltage switching (ZVS) mode, the turn-off switching loss can also be optimized because there is no requirement for light load operation in this mode. Four mosfets with ultra-low on-state resistance are used, thus, the added conduction loss is small. The auxiliary mosfets with high switching frequency are turned on with zero-current and off with zero-voltage, hence, the added switching loss can also be neglected. Furthermore, some drawbacks of the conventional ZVS and ZVZCS converters, e.g., narrow ZVS load range, high primary circulating current, incomplete reset of the primary current, and unreasonable VA rating of the added components, have been well solved. The operation principles and soft switching characteristics are discussed. Experimental results from an 18-kW prototype are provided to verify the proposed converter. [ABSTRACT FROM AUTHOR]

Numerous studies show that power semiconductors are significant contributors to the overall failure rate of pulsewidth modulation (PWM) voltage source rectifier (VSR) systems. Aimed at this problem, this paper presents an improved diagnosis system for open-circuit faults of a three-phase PWM VSR based on ac current distortion characteristics, which consists of a diagnosis module, a register module, and a decision module. The diagnostic module employs a hysteresis comparator to judge the change trend of the currents, and thereby diagnoses the single open-circuit (OC) faults. The register module is employed to achieve multi-switch OC fault diagnosis, and the decision module is used to output the final result. The proposed method extends the previous work to multi-switch OC fault conditions as well as improves the diagnosis accuracy. The experimental results show that the proposed method can correctly achieve fault diagnosis, including 6 kinds of single-switch faults and 15 kinds of different double-switch faults. Additionally, the proposed method also shows superior anti-interference performance and high robustness under abrupt load transient conditions, different power factor conditions, unbalanced and/or distorted grid voltage conditions, and different ac filter structure conditions. Furthermore, the average diagnostic time of this method is only 3.68 ms. [ABSTRACT FROM AUTHOR]

The inductance is an important parameter impacting current ripple calculation, usually with the assumption that the designed inductance performs ideally in most of voltage source inverters (VSIs) applications. However, the initial permeability of magnetic material usually descends when the winding current reaches or goes beyond the saturation limit. In such region of saturation, the implemented inductor does not perform as expected in design stages and its value varies with the bias current. In this paper, analysis and calculation of the current ripple are presented for a three-phase VSI with powder cores-based inductors, which reveals the calculation error of current ripple caused by the soft saturation nature of powder cores. Based on the equivalent single-phase model, the influence of inductance saturation on current ripple can be quantitatively evaluated. Then, a comparison of the current ripple calculation between considering and ignoring inductance saturation of implemented inductors is drawn in detail. Furthermore, under the condition of inductance saturation, the output current ripple peak-to-peak value of three phases is used as the constraint for variable switching frequency pulsewidth modulation (VSFPWM) design. A comprehensive method is developed to compensate the effect of inductance saturation in VSFPWM. At last, the effectiveness of the proposed strategy is verified by the detailed simulation and experiment. [ABSTRACT FROM AUTHOR]

The pulse-width modulated (PWM) switching rectification that can achieve a high power factor (PF) for increasing the energy transfer efficiency between an LC resonator and a rectifier and voltage step-up and -down conversion is proposed for a wireless power transfer (WPT) receiver. The proposed method can emulate the switching rectifier as a resistive load by using an inductor and integrated phase synchronizers. Additionally, similar to a switched-inductor converter that controls the duty cycle ratio (D), the proposed PWM rectifier can control the output voltage VOUT when the input is a rectified, wirelessly coupled voltage instead of a constant voltage. Thus, unlike a conventional PWM switching rectifier for ac mains, an additional voltage conditioning circuit would not be needed after the proposed rectifier for WPT. The proposed PWM switching rectification is implemented in the AMS 0.18 μm 1.8 V/5 V CMOS process. PF = 1 is measured, indicating the most efficient energy transfer, compared to only 0.55–0.65 in a peak detection rectifier. Additionally, 88.2% of peak power conversion efficiency of the switching rectifier is achieved, and the maximum output power is 80.3 mW at 500 kHz of the WPT frequency. Moreover, the measured voltage conversion ratios ranging between 0.73× and 2× are demonstrated in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a novel pulsewidth modulation cell-level diffusion charge redistribution (DCR) converter based on a switched capacitor converter (SCC) utilizing diffusion capacitance of photovoltaic (PV) cells for PV modules under partial shading. Although a discrete inductor and capacitor are additionally necessary, Joule losses associated with switching operations can be reduced compared to the conventional capacitorless DCR converter. First, ac impedance measurement for a PV cell with 125 × 125 mm was performed, and the diffusion capacitance values were measured to be approximately 6.0 mF at its maximum power point voltage of 0.574 V. Second, the theoretical loss model was derived based on the detailed analysis, and it revealed that an optimal duty cycle achieving the lowest Joule loss was dependent on shading conditions. Third, a dual maximum power point tracking (MPPT) algorithm that controls duty cycles of not only the DCR converter, but a front-end boost converter is also proposed. With the dual MPPT control, the DPP converter operates at its optimal duty cycle to minimize the Joule loss while the boost converter seeks the MPP. The experimental results demonstrated that the maximum power significantly increased, thanks to the DCR converter, and that both the DCR and boost converters operated with respective optimal duty cycles. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach to derive a pulsewidth modulation (PWM) technique for the generalized multi-phase drive. This novel approach is called a phase traversing principle. The given phase traversing principle is applied to the proposed PWM technique for five-phase open-end winding induction motor drive fed from a single dc source. The proposed PWM technique has the benefits of phase clamping, symmetrical operation of inverters, and common-mode current (CMC) elimination. Thus, it reduces the switching losses and also minimizes the issue of the CMC. The symmetrical operation of dual inverters further helps in the even distribution of losses. Also, the proposed PWM technique gives a good harmonic performance. The performance of the proposed PWM technique is analyzed using the switching loss function and harmonic flux trajectory methods. The first analysis gives justification of the reduced switching losses. While the second analysis gives the deviations in the motor flux with respect to variation in. modulation indices The proposed PWM technique is verified with both simulation and hardware results. [ABSTRACT FROM AUTHOR]

In order to reduce switching loss of neutral point clamped three-level inverter (NPC TLI), generally discontinuous pulsewidth modulation (DPWM) is used. But it can result in dc offset and ac ripple on neutral point (NP) voltage. So a novel pulse sequence DPWM (NPSDPWM) is proposed to reduce switching loss and control NP voltage simultaneously in this paper. NP voltage is controlled by choosing proper clamping modes. To avoid unexpected switching action during changing clamping mode, an improved pulse sequence is also presented. The switching loss and NP voltage ripple of NPSDPWM, traditional and proposed DPWM in previous literature are compared, respectively. The experimental results show that NPSDPWM has well NP voltage control ability and the switching losses are reduced effectively. [ABSTRACT FROM AUTHOR]

Direct power control (DPC) has been proposed as an effective control method for pulsewidth modulated (PWM) converters. The recent development focuses on the integration of the model predictive (MP) control and DPC to obtain better steady-state performance. In most MP-DPCs, duty cycle optimization (DCO) is a common technique to achieve the power error minimization. However, the periodic occurrence of a duty cycle larger than one (D > 1) deteriorates the performance of the PWM converter by inducing current spikes and power surges. To address this problem, this paper conducts an in-depth examination on the “D > 1” case common in MP-DPC using DCO. It is found the “D > 1” case is caused by the wrong control action of the active power in the starting period of each sector. Furthermore, a new table containing an additional pre-calculated interval in every sector is developed to eradicate the “D > 1” case and its associated power quality issues. Both simulation and experimental results are provided to demonstrate the effectiveness of the new table. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid switch with the combination of large-current silicon (Si) insulated gate bipolar transistor (IGBT) and small-current silicon carbide (SiC) metal-oxide semiconductor field-effect transistor (mosfet) is utilized in a three-phase T-type three-level grid inverter. The hybrid switch can optimize the cost of the system while achieving high efficiency. The relationship between efficiency improvement and cost of the hybrid switch is investigated. Several switching patterns, which can decrease the loss of the small-current SiC mosfet for the hybrid switch, are studied. Different switching patterns for the hybrid switch of the grid inverter are compared based on the inverter efficiency. Finally, a 20 kW three-phase T-type three-level grid inverter prototype with the hybrid switch of large-current Si IGBT and small-current SiC mosfet (1:2.4 SiC/Si current ratio) is built to verify the main results. [ABSTRACT FROM AUTHOR]

This paper proposes a new pulse amplitude width modulation (PAWM) procedure for cascaded H-bridge multilevel inverters fed by dc voltage sources with unequal amplitudes. With proposed procedure, the generated output voltage is obtained modulating a sinusoidal reference signal at the desired fundamental frequency with equally spaced switching angles. It has been analytically demonstrated that, under these assumptions, all harmonics except those of order $n=2kl\pm 1$ , $k=1,2,\ldots$ are deleted from the output voltage waveform. After a detailed description of the method and a comparative analysis with others existing in the literature, its harmonics elimination capability has been experimentally verified with 5-, 7-, 9-, and 11-level cascaded H-bridge inverters, moreover, it has been mathematically demonstrated that it reduces total harmonic distortion below 5% with a 17-level inverter and it is capable of eliminating the first 49 harmonics considered by standards with a 27-level inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel discontinuous pulsewidth modulation (DPWM) modulation strategy for a neutral-point-clamped (NPC) three-level converter (TLC) is proposed to reduce the switching loss, reduce common-mode voltage (CMV), and remove dc offset from the neutral-point (NP) voltage simultaneously, which is named as RCMV_DPWM. Based on the space vector diagram with reduced CMV, all clamping modes under RCMV_DPWM are revealed. Then, the NP voltage is controlled by selecting proper clamping mode. The realization of RCMV_DPWM is also discussed. Moreover, the performances of RCMV_DPWM are analyzed and compared with other PWM strategies in term of the NP voltage ripple, switching loss, and waveform quality. Finally, the feasibility and superiority of RCMV_DPWM are verified by experiments. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

The three-level neutral point-clamped (NPC) converter has attracted much attention in high-power medium-voltage applications, but it is well-known that the NPC topology suffers from unequal power loss distribution among its semiconductor devices. The power loss unbalance problem becomes especially severe when the converter is operating at low fundamental frequencies. To overcome the loss unbalance problem of the NPC converter, the active NPC (ANPC) technique was introduced. However, it is demonstrated in this paper that in many cases, the conventional modulation method for the ANPC converter only marginally relieves the loss unbalance problem. This paper proposes a new modulation scheme (named the adaptive doubled frequency modulation) for the three-level ANPC converter, which significantly improves the power loss and thermal sharing among the semiconductor devices. The basic idea of the proposed scheme is adaptively adjusting the duty cycles of the switching states for every switching cycle, so as to optimize the power loss distribution. Simulation and experimental results verify this new method. [ABSTRACT FROM AUTHOR]

This paper presents a pulse width modulation (PWM) technique for the minimization of the leakage current in the grid-connected/stand-alone transformerless photovoltaic (PV)-cascaded multilevel inverter (CMLI). The proposed PWM technique is integrated with the MPPT algorithm and is applied to the five-level CMLI. Furthermore, using the proposed PWM technique the high-frequency voltage transitions in the terminal and common mode voltages are minimized. Thus, the proposed PWM technique minimizes the leakage current of the PV array and electromagnetic interference filter requirement in the system without addition of any extra switches. Furthermore, this paper also presents the analysis for the terminal voltage across the PV array and the common mode voltage of the inverter based on the switching function. Using the given analysis, the effect of the PWM technique can be analyzed, as it directly links the switching function with the common mode voltage and leakage current. Also, the proposed PWM technique requires reduced number of carrier waves compared to the conventional sinusoidal pulse width modulation technique for the given CMLI. Complete details of the working principle and analysis with the support of simulation and experimental results of the proposed PWM technique are presented in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposes a dual-space vector control scheme for the open-end winding permanent magnet synchronous motor (OEW-PMSM) drive fed by the dual inverter with a single dc supply. Potential zero-sequence current in the open-end winding drive system has to be considered since it causes circulating current in the winding and leads to high current stress of power semiconductor devices and high losses. Zero-sequence current in open-end winding ac motor drives is usually caused by the zero-sequence voltage, and therefore switching combinations which do not produce zero-sequence voltage are used to synthesize the reference voltage in existing methods. But even so, the zero-sequence voltage can also be produced by the dead time of the inverter. In order to suppress zero-sequence current in the OEW-PMSM drive, a dual-space vector control scheme is proposed and a novel dual-inverter space vector pulse width modulation (PWM) with the zero-sequence voltage reference is employed to regulate system zero-sequence voltage in this paper. Compared with existing dual inverter PWM strategies, the novel algorithm build a regulation mechanism for the zero-sequence voltage. The proposed method is compared with the conventional vector control by simulations and experiments, and the results shown that the proposed scheme can suppress zero-sequence current effectively. [ABSTRACT FROM AUTHOR]

In this paper, the near-state pulsewidth modulation (NSPWM), adapted to be implemented in dual-voltage-source inverter (VSI) fed open-end motor, is proposed with the aim of mitigating low-order harmonics (which lead to current total harmonic distortion (THD) minimization). The following two proposed methods are studied in detail: 1) fixing phase angle displacement (PAD) between two VSIs to 120° while adjusting the modulation index (MI); and 2) fixing MI to the predetermined value (wherein low-order harmonics are highly mitigated) while adjusting PAD. Furthermore, the proposed approaches enhance efficiency by limiting the number of commutations within the switching interval. The paper also presents the mathematical approaches to accurately determine low-order harmonic components and switching losses for dual-VSI structure. The experimental setup, including dual-VSI and open-end induction motor, is assembled in the laboratory to evaluate performance of the proposed method. Finally, the simulation results, carried out in the MATLAB/Simulink environment, are found to be in close agreement with experimental data. [ABSTRACT FROM AUTHOR]

Magnetically coupled impedance-source (MCIS) networks are recently introduced impedance networks intended for various high-boost applications. It employs coupled magnetic in the circuit to achieve higher voltage gain. Various MCIS networks have been proposed in the literature for myriad applications; however, due to effective role of system modeling in the closed-loop controller design, this paper is allocated to small-signal modeling and analysis of MCIS converters. The modeling is performed by means of the circuit averaging and averaged switch technique. A generalized small-signal derivation is demonstrated for pulse width modulation (PWM) MCIS converters and it is shown that the derived transfer functions can simply be applied to Y-source, Γ-source, and T-source impedance networks. Various transfer functions for capacitor voltage, output voltage, magnetizing current, input and output impedance are derived and have been validated through frequency and dynamic responses of computer simulation results. In addition, a comprehensive analysis has been done for all mentioned PWM MCIS converters regarding their circuit parameters. Furthermore, the effect of considering the equivalent series resistances of capacitor and inductor on the stability margin of MCIS converters is revealed in this paper. Finally, in order to validate the derived transfer functions and to consolidate the perfumed analysis, experimental results are presented for all mentioned MCIS converters. [ABSTRACT FROM PUBLISHER]