Search

In the applications such as mixed-color light emitting diode (LED) lighting system, LED drivers are always required to provide constant current for each LED string and each current should be controlled independently. For this purpose, a single-stage series-type LED driver with independent control of N-channel output currents is proposed in this paper. The function of power factor correction can be realized inherently to obtain high power factor. N active output units, each one made up of a power switch, a diode, and an output filter capacitor, are series-connected to form the series-type N-channel outputs structure. According to different current reference values, N-channel output currents can be independently regulated just by sampling each output current to adjust the duty cycle of each secondary output-switch automatically. The operating principle and independent closed-loop control strategy of the proposed LED driver with N = 3 are analyzed as an example in detail. Finally, the quantitative parameter design method for a 120 W prototype is elaborated. And, the experimental results are presented to verify the effectiveness of the LED driver and the correctness of parameter design method. [ABSTRACT FROM AUTHOR]

In order to reduce switching loss of neutral point clamped three-level inverter (NPC TLI), generally discontinuous pulsewidth modulation (DPWM) is used. But it can result in dc offset and ac ripple on neutral point (NP) voltage. So a novel pulse sequence DPWM (NPSDPWM) is proposed to reduce switching loss and control NP voltage simultaneously in this paper. NP voltage is controlled by choosing proper clamping modes. To avoid unexpected switching action during changing clamping mode, an improved pulse sequence is also presented. The switching loss and NP voltage ripple of NPSDPWM, traditional and proposed DPWM in previous literature are compared, respectively. The experimental results show that NPSDPWM has well NP voltage control ability and the switching losses are reduced effectively. [ABSTRACT FROM AUTHOR]

High gain bidirectional dc–dc converter with high efficiency and high power density is a much desired circuit in any converter/inverter system. It is well known that switched capacitor circuits that are variants of the Dickson converter are suitable candidates for such a system. Modular design, absence of external magnetic components, and high efficiency are some of the features that make them suitable candidates. But, the inability to provide fractional and variable voltage gains at high efficiency during normal operation severely limits their application. It also leads to higher voltage stress in the overall system. The aim of this paper is twofold. First, a generalized modular switched capacitor converter, the “(n/m)X converter,” which is a variant of the original Dickson converter is introduced. Using this generalized configuration, the converter can be designed for a required fractional gain. Next, two different methods to enable dynamic variation in gain with high efficiency using the (n/m)X converter are proposed. Detailed analysis, design steps, equivalent circuits, and experimental results for a 1 kW prototype of a variable (4/0.5)X boost converter validate the proposed theory. A peak measured efficiency of over 95% is achieved for the prototype. The design framework and analysis in this paper can be extended to a generic (n/m)X converter. [ABSTRACT FROM AUTHOR]

This paper introduces a novel five-level nested neutral point piloted (NNPP) converter and analyzes the operating principle of five-level NNPP converter. This paper presents a novel space vector pulse width modulation (SVPWM) algorithm based on gh coordinate for five-level NNPP converter. First, the common-mode voltage is reduced by choosing the appropriate redundant switching states. After that, the floating-capacitor voltage balance control strategy is presented. The appropriate switch combinations of each phase are determined by the control requirements of floating-capacitor voltages respectively and the hardware mapping method of the switching states is presented. Furthermore, the neutral-point voltage balance control strategy is presented. In order to balance the dc-link capacitor voltages, the seven-segment switching sequence is selected according to the control requirements of dc-link capacitor voltages and the neutral-point voltage regulatory factor is introduced to regulate the durations of the redundant switching states in a switching cycle. Finally, the validity of the novel SVPWM algorithm with decoupling control strategies of floating-capacitor voltages and dc-link capacitor voltages is verified by the experimental results of five-level NNPP converter under steady-state and dynamic conditions. [ABSTRACT FROM AUTHOR]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

This paper proposes a new methodology to control a three-phase boost power factor correction (PFC) using a single dc output voltage sensor. Typically, a PFC control technique requires measurement from five independent sensors, i.e., two input voltages, one output dc voltage, and two input phase currents. Elimination of four sensors in the control system of a PFC converter is theoretically feasible and implementable without compromising stability and power quality of the converter, as analyzed and presented in this paper. The proposed control technique uses the ripple information of the measured dc-link voltage, converter dynamics, and switching states at a preceding sample in order to estimate the present state of four other unknown state variables and, thus, establishes the control method. A 2.2-kW experimental prototype of a three-phase boost PFC is developed and tested to verify the accuracy and applicability of the proposed control logic at different line and load conditions. According to the experimental measurements, conversion efficiency more than 98%, total harmonic distortion as low as 4.3%, and an output voltage ripple of ±2% are achieved at 2.2-kW output power. [ABSTRACT FROM AUTHOR]

This part of the paper illustrates the use of the expression derived in Part I for predicting subharmonic oscillation in switching regulators. Six case studies with different control schemes from the recent literature are used to validate the novel approach and the new derived expression, which is benchmarked for these case studies against results obtained using the discrete-time modeling approach or Floquet theory combined with Filippov method. Numerical simulations from the circuit-level switched models, implemented in PSIM software, are used to demonstrate the correctness of the derived closed-form condition. A procedure is presented to apply the approach of the paper to power converters with nonlinear sources, such as photovoltaic (PV) arrays or fuel cells. Experimental measurements from a boost converter prototype for PV applications are also provided to validate the theoretical predictions and the numerical simulations showing a remarkable agreement. [ABSTRACT FROM AUTHOR]

A three-phase three-level (TPTL) converter is an optimal alternative for high-input and high-power dc/dc conversion system. The voltage stress on the primary switch is only half of the input voltage due to its three-level (TL) structure, and the current rating of power devices can be reduced by the three-phase configuration. To achieve soft switching and improve efficiency, the resonant tank can be introduced to optimize the performance of the converter. In this paper, a novel TPTL LC-type series resonant converter with few switches and simple configuration is proposed. The voltage stress on all switches can be reduced to the half of the input voltage, and the voltage across output rectifiers is clamped to the output voltage; as a result, the proposed converter is suitable for high-input/output applications. Meanwhile, the ripple frequency of the output current can be increased significantly, resulting in a reduced filter requirement. Variable frequency control strategy is adopted in order to obtain zero-voltage switching for all switches and zero-current switching for all rectifier diodes in wide input voltage and load range. In this paper, the comprehensive analysis on the proposed converter is carried out, including the operation mode classification, the operating mechanism under different operation mode, along with the circuit model, and gain characteristics of the converter by the fundamental harmonic analysis. Experimental results from a 440–590 V input and 400 V/5 A output are presented to verify the theoretical analysis and the performance of the converter. [ABSTRACT FROM AUTHOR]

In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage of the inverter can be increased from 0.577 to 0.637 V\text{dc} without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction motor drive can be operated till the full speed range (0–50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors. The inverter topology and its operation for extending the modulation range is analyzed extensively. Simulation and experimental results for both steady-state and dynamic operating conditions are presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) systems for electric vehicle (EV) charging often have to operate under a wide range of coupling factors and loads, potentially mistuning the primary power supply. This is especially a problem in dynamic applications where the vehicles are moving. This paper investigates the design of a self-tuning power supply by utilizing a switchable bank of capacitors with a push–pull tuning topology. The proposed power supply is able to handle operation under a wide range of coupling factors and loading conditions while achieving ZVS operation at a fixed frequency. A mathematical model is developed to model the system and an experimental system is built to test the design. The experimental system is able to deliver a constant 1 kW over a coupling factor range of 0.1–0.33. A detection circuit to monitor the state of tuning of the power supply is presented along with a control scheme to maintain optimal tuning. [ABSTRACT FROM AUTHOR]

The degradation in power quality causes adverse economical impact on the utilities and customers. Harmonics in current and voltage are one of the most commonly known power quality issues and are solved by the use of a hybrid series active power filter (HSAPF). In this paper, a new controller design using sliding-mode controller-2 is proposed to make the HSAPF more robust and stable. An accurate averaged model of a three-phase HSAPF is also derived in this paper. The design concept of the robust HSAPF has been verified through simulation and experimental studies, and the results obtained are discussed. [ABSTRACT FROM AUTHOR]

This paper presents a single-switch isolated dc–dc converter suited for a very high-frequency switching operation, especially above 10 MHz. The converter features a small number of passive components, low-switching loss, and low-voltage stress on the switch. In order to achieve low-voltage stress while maintaining zero voltage switching, the voltage waveform across the switch is shaped by designing the resonant network of the converter. The resonant network includes main parasitic components, such as leakage inductances of the transformer and the junction capacitance of the switch. Furthermore, some resonant elements are entirely replaced by these parasitic components under the specific condition. This paper derives the conditions and then minimizes the number of passive components. To validate the design procedure and the performance of the proposed converter, a GaN-based prototype was implemented. It operates at 10 MHz and provides the output power of 10 W from the dc input voltage of 50 V. The output voltage is regulated to 20 V by the ON–OFF control. Experimental results show that the peak voltage on the switch is reduced to 2.2–2.3 times the dc-input voltage and the efficiency of 69% is achieved under the full load. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

Increasing demands for power supplies have contributed to the population of high-frequency ac (HFAC) power distribution system (PDS), and in order to increase the power capacity, multilevel inverters (MLIs) frequently serving as the high-frequency (HF) source-stage have obtained a prominent development. Existing MLIs commonly use more than one voltage source or a great number of power devices to enlarge the level numbers, and HF modulation (HFM) methods are usually adopted to decrease the total harmonic distortion (THD). All of these have increased the complexity and decreased the efficiency for the conversion from dc to HF ac. In this paper, a nine-level inverter employing only one input source and fewer components is proposed for HFAC PDS. It makes full use of the conversion of series and parallel connections of one voltage source and two capacitors to realize nine output levels, thus lower THD can be obtained without HFM methods. The voltage stress on power devices is relatively relieved, which has broadened its range of applications as well. Moreover, the proposed nine-level inverter is equipped with the inherent self-voltage balancing ability, thus the modulation algorithm gets simplified. The circuit structure, modulation method, capacitor calculation, loss analysis, and performance comparisons are presented in this paper, and all the superior performances of the proposed nine-level inverter are verified by simulation and experimental prototypes with rated output power of 200 W. The accordance of theoretical analysis, simulation, and experimental results confirms the feasibility of proposed nine-level inverter. [ABSTRACT FROM AUTHOR]

The matrix converter (MC) is a direct ac–ac power converter without an intermediate dc link. It has several attractive features, such as high power density, four-quadrant operation, and bidirectional power flow. However, the application of MCs in high-voltage and high-power systems is still limited by the device voltage levels. It is well known that the multilevel power converter technology can be a solution to enhance the voltage rating and improve harmonic performance in many applications. Therefore, an application of a multilevel topology based on a direct ac–ac power converter is proposed in this paper. This paper first introduce the topology structure, the switching pattern grouping method, and the proposed output voltage modulation method for a five-level capacitor clamped multilevel matrix converter (5LMC). Amplitude coefficient adjustment is also introduced as a part of modulation procedure to simplify the duty cycles calculation. Simulation from MATLAB/Simulink is given to demonstrate the theoretical work. Experimental results from a five-level matrix converter prototype are presented to validate the theoretical findings. [ABSTRACT FROM AUTHOR]

This paper presents a novel family of single-switch resonant dc–dc converters with low switch voltage stress. The single-switch resonant converter which has a ground-referenced switch is advantageous for implementing the gate drive circuit and operating at several-MHz switching frequency. However, the conventional ones mostly have high voltage stress on the switch, roughly 4–5 times the input voltage. In this paper, we propose the single-switch converter topologies derived from the drain-source impedance networks consisting of two inductors and two capacitors. The switch voltage of the proposed converters is shaped into a near trapezoid by designing the resonant networks to have the desired drain-source impedance. Furthermore, a simple and specific design scheme is presented here so that the peak switch voltage is lowered to 2.2–2.5 times the input voltage while zero voltage switching is achieved. Experimental results from a 20-W GaN-based prototype operating at 10 MHz demonstrate the feasibility of the proposed converter topologies and the design method. [ABSTRACT FROM AUTHOR]

A new active-clamped zero-voltage switching (ZVS) push–pull converter is proposed in this paper. Compared with the conventional push–pull converter, one auxiliary switch $Q_{{3}} and a clamping capacitor Ca are added in the primary side of the transformer to recycle the energy stored in the leakage inductors and clamp the voltage spike. Owing to the proposed converter which maintains ZVS of all the three switches from full load to very light-load condition, switching losses are reduced significantly. The voltage across the switch can be clamped at the input voltage plus the clamping capacitor voltage, i.e., V\rm{in}{+}VCa, are much less than those of a conventional push–pull converter that enabling the use of low-voltage, low-performance, and low-cost devices. In addition, the proposed topology can eliminate the problems of flux imbalance existing in the conventional one. Detailed operation, analysis, design, comparative study, and experimental results for the proposed converter are presented in this paper. An 800 W prototype was developed in the laboratory to evaluate and demonstrate the validity of the converter. [ABSTRACT FROM AUTHOR]

The three-level neutral point-clamped (NPC) converter has attracted much attention in high-power medium-voltage applications, but it is well-known that the NPC topology suffers from unequal power loss distribution among its semiconductor devices. The power loss unbalance problem becomes especially severe when the converter is operating at low fundamental frequencies. To overcome the loss unbalance problem of the NPC converter, the active NPC (ANPC) technique was introduced. However, it is demonstrated in this paper that in many cases, the conventional modulation method for the ANPC converter only marginally relieves the loss unbalance problem. This paper proposes a new modulation scheme (named the adaptive doubled frequency modulation) for the three-level ANPC converter, which significantly improves the power loss and thermal sharing among the semiconductor devices. The basic idea of the proposed scheme is adaptively adjusting the duty cycles of the switching states for every switching cycle, so as to optimize the power loss distribution. Simulation and experimental results verify this new method. [ABSTRACT FROM AUTHOR]

Direct power control (DPC) has attracted wide attention due to its advantages of simple structure, quick response, strong robustness, and elimination of current regulation/pulse width modulation blocks. However, conventional table-based DPC cannot work well when the grid voltages are unbalanced. Some work has been done on DPC to mitigate the influence of grid unbalance by adding power compensations to the original power references. However, they are usually complicated due to the positive/negative-sequence extraction of grid voltage and/or currents. Furthermore, applying only one voltage vector during one control period leads to high steady-state power ripples. This paper proposes an improved DPC by using a new definition of instantaneous reactive power. As a result, the distortion in grid current is eliminated, and constant active power and new reactive power are obtained. Neither complicated calculation of power compensation nor positive/negative-sequence extraction of grid voltage/current is required. The corresponding switching table suitable to regulate both active power and the new reactive power is established. Furthermore, the concept of duty cycle control is introduced to further improve the steady-state performance. Both simulation and experimental results are presented to confirm the theoretical study and the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

A novel fault diagnosis method and a fault tolerant scheme for open-circuit faults on a traction rectifier are proposed in this paper. When an open-circuit fault occurs in any leg of the rectifier, indication will be generated accurately to identify the faulty leg without utilization of any extra sensors. Furthermore, the faulty rectifier can be reconfigured to maintain its full output rate to prevent traction rectifier breakdown. The fault diagnosis process is neither related to control trigger signal nor the load fluctuation. The involved parameters are the input and output voltage of the rectifier, which are the most common parameters in rectifier control. Working under zero voltage and zero current, five additional switch sets are adopted for the fault-tolerant control process to reconfigure the topological structure between the traction rectifier and the traction transformer, meanwhile the original structure of the rectifier is retained. Analysis, design, and implementing consideration for both normal and abnormal operating situations of the traction rectifier are present in this paper. The experiment is processed to verify the effectiveness of the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents a pulse width modulation (PWM) technique for the minimization of the leakage current in the grid-connected/stand-alone transformerless photovoltaic (PV)-cascaded multilevel inverter (CMLI). The proposed PWM technique is integrated with the MPPT algorithm and is applied to the five-level CMLI. Furthermore, using the proposed PWM technique the high-frequency voltage transitions in the terminal and common mode voltages are minimized. Thus, the proposed PWM technique minimizes the leakage current of the PV array and electromagnetic interference filter requirement in the system without addition of any extra switches. Furthermore, this paper also presents the analysis for the terminal voltage across the PV array and the common mode voltage of the inverter based on the switching function. Using the given analysis, the effect of the PWM technique can be analyzed, as it directly links the switching function with the common mode voltage and leakage current. Also, the proposed PWM technique requires reduced number of carrier waves compared to the conventional sinusoidal pulse width modulation technique for the given CMLI. Complete details of the working principle and analysis with the support of simulation and experimental results of the proposed PWM technique are presented in this paper. [ABSTRACT FROM PUBLISHER]

This paper deals with a thorough analysis of zero-voltage switching, especially for bidirectional inductorless piezoelectric transformer-based switch-mode power supplies with a half-bridge topology. Practically, obtaining zero-voltage switching for all of the switches in a bidirectional piezoelectric power converter is a difficult task. However, the analysis in this paper will be convenient for overcoming this challenge. The analysis defines the zero-voltage region indicating the operating points whether or not soft switching can be met over the switching frequency and load range. For the first time, a comprehensive analysis is provided, which can be used as a design guideline for applying control techniques in order to drive switches in piezoelectric transformer-based converters. This study further conveys the proposed method to the region where all the switches can obtain soft switching. Moreover, the analysis can be applied to other types of resonant converters with or without piezoelectric transformers. Experimental and simulation results are provided verifying the performed analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a modular multilevel converter (MMC) topology for high-voltage dc (HVdc) system applications. The proposed MMC employs two half-bridge converters, a cascade of networks that consist of electronic switches, and multiple capacitors. Thus, charged capacitors are inserted in series with the arm current path, for a desired level of the output ac voltage. The switches that must be turned on are judiciously selected for the most efficient current path. The proposed MMC also offers dc-side fault handling capability. The paper compares the proposed MMC with the half-bridge submodule-based MMC, full-bridge submodule-based MMC, and clamp-double submodule-based MMC technologies. It is shown that the proposed MMC is more efficient than the three aforementioned MMC technologies, while it offers the same fault handling capability as that of an equivalent full-bridge-based MMC. Time-domain simulation studies confirm the effectiveness of the proposed MMC under various normal and faulted operating scenarios, using detailed as well as reduced models. [ABSTRACT FROM AUTHOR]

To reduce current stress and improve efficiency of dual active bridge (DAB) dc–dc converters, various control schemes have been proposed in recent decades. Most control schemes for directly minimizing power losses from power loss modeling analysis and optimization aspect of the adopted converter are too difficult and complicated to implement in real-time digital microcontrollers. Thus, this paper focuses on a simple solution to reduce current stress and improve the efficiency of the adopted DAB converter. However, traditional current-stress-optimized (CSO) schemes have some drawbacks, such as inductance dependency and an additional load-current sensor. In this paper, a simple CSO scheme with a unified phase-shift (UPS) control, which can be equivalent to the existing conventional phase-shift controls, is proposed for DAB dc–dc converters to realize current stress optimization. The simple CSO scheme can overcome those drawbacks of traditional CSO schemes, gain the minimum current stress, and improve efficiency. Then, a comparison of single-phase-shift (SPS) control, simple CSO scheme with dual-phase-shift (CSO-DPS) control, simple CSO scheme with extended-phase-shift (CSO-EPS) control, and simple CSO scheme with UPS (CSO-UPS) control is analyzed in detail. Finally, experimental results verify the excellent performance of the proposed CSO-UPS control scheme and the correctness of theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, the near-state pulsewidth modulation (NSPWM), adapted to be implemented in dual-voltage-source inverter (VSI) fed open-end motor, is proposed with the aim of mitigating low-order harmonics (which lead to current total harmonic distortion (THD) minimization). The following two proposed methods are studied in detail: 1) fixing phase angle displacement (PAD) between two VSIs to 120° while adjusting the modulation index (MI); and 2) fixing MI to the predetermined value (wherein low-order harmonics are highly mitigated) while adjusting PAD. Furthermore, the proposed approaches enhance efficiency by limiting the number of commutations within the switching interval. The paper also presents the mathematical approaches to accurately determine low-order harmonic components and switching losses for dual-VSI structure. The experimental setup, including dual-VSI and open-end induction motor, is assembled in the laboratory to evaluate performance of the proposed method. Finally, the simulation results, carried out in the MATLAB/Simulink environment, are found to be in close agreement with experimental data. [ABSTRACT FROM AUTHOR]

Magnetically coupled impedance-source (MCIS) networks are recently introduced impedance networks intended for various high-boost applications. It employs coupled magnetic in the circuit to achieve higher voltage gain. Various MCIS networks have been proposed in the literature for myriad applications; however, due to effective role of system modeling in the closed-loop controller design, this paper is allocated to small-signal modeling and analysis of MCIS converters. The modeling is performed by means of the circuit averaging and averaged switch technique. A generalized small-signal derivation is demonstrated for pulse width modulation (PWM) MCIS converters and it is shown that the derived transfer functions can simply be applied to Y-source, Γ-source, and T-source impedance networks. Various transfer functions for capacitor voltage, output voltage, magnetizing current, input and output impedance are derived and have been validated through frequency and dynamic responses of computer simulation results. In addition, a comprehensive analysis has been done for all mentioned PWM MCIS converters regarding their circuit parameters. Furthermore, the effect of considering the equivalent series resistances of capacitor and inductor on the stability margin of MCIS converters is revealed in this paper. Finally, in order to validate the derived transfer functions and to consolidate the perfumed analysis, experimental results are presented for all mentioned MCIS converters. [ABSTRACT FROM PUBLISHER]

Based on the Z-source inverter, this paper proposes a novel commutation torque ripple reduction strategy for brushless DC motor (BLDCM). The proposed strategy employs the same modulation mode in both the normal conduction period and the commutation period, and the commutation torque ripple is reduced by regulating the shoot-through vector and active vector duty cycles. The proposed detection method acquires the end point of commutation by comparing the clamped terminal voltages with reference zero level, and the signal-noise-ratio of the detection is improved by avoiding the attenuation of the terminal voltages. Furthermore, a certain pulse width of the shoot-through vector can not only reduce the commutation torque ripple but also provide a new opportunity to detect the end point of commutation. Moreover, Z-source inverter provides the buck–boost ability for BLDCM drive system, then the dc voltage utilization can be improved, and the safety of the drive system can also be improved. In addition, this paper analyzes the terminal voltages during each vector. The experimental results verify the correctness of the theories and the effectiveness of the proposed approach. [ABSTRACT FROM PUBLISHER]

AC voltage regulation is required in both the domestic and industrial sectors to avoid undesired effects from random voltage variations of the power supply. The paper introduces an ac voltage stabilizer/converter (ACVS) that is based on a controllable autotransformer technology. The proposed ACVS offers a specified strategy of voltage regulation, less harmonics, and low cost. The paper explains the operating principle of the ACVS and derives its nonlinear mathematical model. To ensure the desired performance of the ACVS while it is subject to uncertain input voltage and load variations, an optimal control strategy is designed. It is achieved via transforming the ACVS model extending with fictive axis emulation into a rotating reference frame and the linearization of the model via specific orientation of the reference frame and introducing a linear control action. Operation of the ACVS is simulated under different disturbances due to load and grid voltage changes, and compared to voltage stabilization with application of I and PI controllers. Experimental results are presented to demonstrate the voltage regulation technology. [ABSTRACT FROM PUBLISHER]

In several electrical dc–ac power conversions, the ac output voltage is higher than the input voltage. If a voltage-source inverter (VSI) is used, then an additional dc–dc boosting stage is required to overcome the step-down VSI limitations. Recently, several impedance source converters are gaining higher attentions [1], [2], as they are able to provide buck-boost capability in a single conversion stage. This paper proposes the merging of the boost stage and the VSI stage in a single stage dc–ac power conversion, denoted as split-source inverter (SSI). The proposed topology requires the same number of active switches of the VSI, three additional diodes, and the same eight states of a conventional space-vector modulation. It also shows some merits compared to Z-source inverters, especially in terms of reduced switch voltage stress for voltage gains higher than 1.15. This paper presents the analysis of the SSI and compares different modulation schemes. Moreover, it presents a modified modulation scheme to eliminate the low frequency ripple in the input current and the voltage across the inverter bridge. The proposed analysis has been verified by simulation and experimental results on a 2.0-kW prototype. [ABSTRACT FROM PUBLISHER]

Modular multilevel converters (MMCs) are being developed for the grid connection of offshore wind or tidal farms. In order to reduce the construction and maintenance costs, it is desirable to reduce the weight and volume of the system. In current MMC submodule designs, the reservoir capacitor usually accounts for over 50% of the total volume and 80% of weight. This paper presents a new design concept and control principle for a submodule using the stacked switched capacitor (SSC) architecture that can significantly reduce the capacitor size in an MMC. Practical considerations for a high-voltage high-power SSC-based MMC submodule are presented in this paper, through the design of a 21-level, 40-kV (pole-pole dc), 19.1-MW, grid-connected system, and the concept is demonstrated experimenttally on a scaled-down 400-V, 12.3-Apeak laboratory prototype submodule. It is shown that with the proposed SSC architecture, the total volume of capacitors in each submodule can be reduced by more than 40% without significantly increasing the power loss. [ABSTRACT FROM AUTHOR]

This paper proposes a new fault-tolerant strategy for the purpose of revamping the performance of three-phase multilevel (ML) converters with faulty switches. The proposed fault-tolerant strategy is based on an adaptation of the modified space vector modulation (SVM) technique to the fundamental phase-shift compensation method. The proposed fault-tolerant strategy generates balanced line-to-line voltages with increased voltage levels in the faulty condition. In this paper, first a brief background about cascaded H-bridge (CHB) ML converters and SVM technique is provided. Then the proposed fault-tolerant strategy and the modified SVM technique are presented. Finally, several experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

Aimed at the problem that the auxiliary commutation circuit (ACC) of auxiliary resonant commutated pole (ARCP) inverters has a high loss in commutation processes, this paper presents a novel modulation strategy with shunt dead time based on a double ARCP (DARCP) inverter. In comparison with the original modulation strategy, this modulation strategy cannot only achieve soft switching for all switches, but also avoid the superposition of resonance current and load current at commutation moments in double ACCs (DACCs) and make the maximum current through DACCs approximately equal to load current in commutation processes. So, the circulating current loss in DACCs and the current stress of auxiliary switches can be effectively reduced. According to the equivalent circuits in different operation modes under the novel modulation strategy, this paper analyzes the operation principle, soft-switching implementation condition, and optimal parameter design procedure of the DARCP inverter. Finally, a 10-kW–16-kHz DARCP inverter prototype with insulated gate bipolar transistor-based switches is built. Experimental results are given to demonstrate the validity and features of the DARCP inverter under the novel modulation strategy. [ABSTRACT FROM AUTHOR]

This paper presents an analytical and experimental comparison of a two-phase buck converter and a two-phase, series capacitor buck converter. The limitations of a conventional buck converter in high-current (10 A or more), and high-frequency (HF, 3–30 MHz) point-of-load voltage regulators with large voltage conversion ratios (10-to-1) are highlighted. The series capacitor buck converter exhibits desirable characteristics at HF, including lower switching loss, less inductor current ripple, automatic phase current balancing, duty ratio extension, and soft charging of the energy transfer capacitor. Analysis of the topologies indicates that switching loss and inductor core loss can dominate at HF. Results from side-by-side 12 V input, 1.2 V output hardware prototypes demonstrate that the series capacitor buck converter has up to 12 percentage points higher efficiency at 3 MHz and reduces power loss by up to 33% at full load (10 A). Some guidelines for inductor selection are provided, and a switch stress comparison reveals that the maximum converter switch stress is reduced by 30%. [ABSTRACT FROM AUTHOR]

The low threshold voltage of Gallium Nitride enhancement mode FETs is a concern in synchronous dc–dc buck converters. This paper presents a converter using a gate drive with a negative biased gate voltage on the low-side FET to improve the dV/dt robustness. The resulting much larger voltage drop during the dead time conduction is a concern as it can quickly overcharge the bootstrap capacitor voltage. This paper demonstrates that with a negative biased gate voltage, the rise in the bootstrap capacitor voltage is predominantly caused by the change in effective dead time conduction due to a variation in output load. A spice model to estimate the change is presented and verified. This paper also found that a change in the bootstrap capacitor voltage must be prevented as it leads to a significant change in turn-on dynamics, resulting in higher dV/dt stress with an increase in output load. To prevent a change in bootstrap capacitor voltage, different techniques such as Zener diode clamping and an external free-wheeling Schottky diode are tested and discussed. Finally, a modification of a standard bootstrap circuit using a series inductor is proposed and tested. It has been found to be the most effective method in preventing a variation in the bootstrap capacitor voltage and should be included when using a negative gate drive in a GaN dc–dc buck converter. [ABSTRACT FROM AUTHOR]

The increasing interest in multiphase drive systems has led to the extension of inverter topologies and pulse width modulation (PWM) methods from three-phase to multiphase occasions. Carrier-based PWM (CPWM) dominates space vector PWM when the phase number increases, because of its simple computation and modular implementation. Although intensive work has been done on modifying PWM methods to reduce the common-mode voltage (CMV), not enough work has been done on CPWM methods with CMV reduction for multiphase drives. This paper extends the phase-shifted sinusoidal PWM (PS-SPWM) method for five-phase and six-phase two-level voltage-source inverters (VSI) and employs the intersection-plotting method and Fourier analysis to reveal the nature of the CMV. Both experiment and simulation results comply with theoretical analysis that compared with the conventional SPWM, the PS-SPWM can effectively reduce the CMV in peak-to-peak value and RMS value, though it leads to a higher phase current distortion. In addition, the hardware realization of PS-SPWM for multiphase inverters by a distributed control system is presented in this paper. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

In this paper, a highly efficient isolated resonant converter with a novel modulation method is proposed for delivering power from photovoltaic (PV) modules to the dc microgrid. The proposed modulation method allows the converter to boost low input voltages and regulate a wide input voltage range. The converter design is based on a series resonant converter (SRC) that operates at the resonant frequency to achieve highest efficiency under nominal input voltage condition. Under shadowed or low irradiance conditions of PV panels, the converter will operate with the proposed “double-pulse duty cycle” modulation method to step up the voltage for the dc microgrid connection. With the proposed modulation method, the output switches serve for both synchronous rectification and voltage boost function. This method enables a higher voltage boost ratio than the SRC without adding additional switches while operating at the resonant frequency. A 300-W hardware prototype with gallium-nitride devices is built to verify the performance of the proposed converter and modulation method. The converter achieved a peak efficiency of 98.9% and a California Energy Commission weighted efficiency of 98.7% under nominal input voltage condition. [ABSTRACT FROM AUTHOR]

This paper investigates basic stability properties of the three-level flying-capacitor Buck converter when operated under current-mode control (CMC). The proposed analysis is developed for both peak CMC (P-CMC) and valley CMC (V-CMC), and addresses both the static instability of the inductor current and the flying capacitor (FC) voltage runaway phenomenon. Conditions for avoiding current subharmonic oscillations are derived first, along with the expressions of the minimal compensation ramp, which guarantee current stability throughout the entire operating range. As for the stability of the FC voltage, P-CMC results to be inherently unstable unless the converter operates with a relatively large peak-to-peak inductor-current ripple, a feature not yet recognized in the literature. However, V-CMC results to be inherently stable once the static instability of the current is eliminated with an external compensating ramp—a property that has been highlighted in the literature but never formally proven. The proposed analysis is verified both using a simulation model and experimentally using a 3.3-V, 500-mA, 500-kHz prototype. [ABSTRACT FROM AUTHOR]

A variable switching frequency space vector modulation control method is proposed in this paper. It is used to achieve zero-voltage switching (ZVS) for two parallel 180° interleaved three-phase grid-connected voltage-source inverters at unity power factor. A wide range of ZVS can be achieved without any additional sensor, auxiliary circuit, or current zero-crossing detection circuit. The carrier wave frequency is easy to be calculated and updated with digital control. The current ripple is precisely predicted and controlled to minimize unnecessary circulation loss. The high current ripple at the inverter side can be considerably canceled by the parallel interleaved configuration. LCL filter is used to further attenuate the current ripple and improve the power quality at the grid side. The switching loss can be significantly reduced especially by using a wide bandgap device with low turn-off loss. The power density is greatly improved owing to the high switching frequency and low component parameters of the filter. A 4.5-kW simulation and experimental prototype interfacing 400 V dc with a three-phase 110-V ac grid is developed to verify the performance of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Leakage current reduction is one of the important issues for transformerless photovoltaic (PV) systems. Many interesting solutions have been reported to reduce the leakage current for three-phase PV inverters. However, most of them are limited to two-level inverters. Moreover, there is a potential risk of the overcurrent phenomenon. In order to solve the problem, a Z-source three-level four-leg inverter with a new modulation strategy is proposed in this paper. First, the mathematical modeling of the three-level four-leg Z-source inverter for leakage current reduction is established for the first time. Second, a new carrier-based modulation strategy is proposed by utilizing the effective large, medium, small, and zero vectors, instead of the invalid vectors, to achieve the constant common-mode voltage, as well as the leakage current suppression. Finally, the proposed solution is carried out on the Texas Instruments TMS320F28335 DSP + Xilinx XC3400 field-programmable gate array digital control hardware platform. The experimental results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

The widespread use of electronic devices increases the need for compact power factor corrected power supplies. This paper describes an isolated power factor corrected power supply that utilizes the leakage inductance of the isolation transformer to provide boost inductor functionality. The bulk capacitor is in the isolated part of the power supply allowing for controlled startup without dedicated surge limiting components. A control method based on switch timing and input/output voltage measurements is developed to jointly achieve voltage regulation and input power factor control. A prototype design is implemented with detailed measurements and waveforms shown to confirm the desired functionality. [ABSTRACT FROM AUTHOR]

This paper explores the issue of the neutral-point oscillation in the four-leg neutral-point clamped inverter. Such an issue is closely associated with the neutral-point current, so this study models the inverter on the dc side to clarify its relationship and presents a three-dimension pulsewidth modulation to eliminate the neutral-point oscillation. In addition, an offset-injection approach to reducing the neutral-point oscillation is also investigated and discussed. The laboratory test results will validate the analysis of the proposed approach, and a discussion will be presented to evaluate the effectiveness of eliminating the neutral-point oscillation. [ABSTRACT FROM AUTHOR]

The six-phase asymmetrical induction motors (SPIMs) are employed for high power medium voltage drive due to its attractive features of reduced stator copper loss, lower torque pulsation, higher torque per ampere, and higher reliability. In this paper, analysis of carrier-comparison-based pulse width modulation (PWM) techniques namely sinusoidal PWM and double zero-sequence injection PWM are carried out from a space vector perspective. Furthermore, new space vector pulsewidth modulation (SVPWM) techniques are developed by modifying the switching sequences of carrier-based PWM techniques. A comprehensive analysis of these PWM techniques is carried out in terms of harmonic flux trajectories, squared harmonic flux, and harmonic distortion factor (HDF). As a result, modified SVPWM technique namely 6ΦSVM3 is found superior to aforesaid PWM techniques, which significantly reduces HDF and provides lower current total harmonic distortion (THD). The experimental results of aforementioned PWM techniques are obtained and verified from six phase asymmetrical induction motor fed by dual two-level 3ΦVSIs. This paper is also accompanied by a video file of experimental test setup recorded while 6ΦSVM2 is running on SPIM. [ABSTRACT FROM AUTHOR]

This paper studies the driving of white light emitting diodes (LEDs) from very low voltages in the 1.2 to 2 V range. The proposed idea is based on replacing the standard Schottky diode used in conventional converter topologies (i.e., buck, buck–boost, and boost) with an LED while shortcutting the output of the converter. In this configuration, the LED works both as the load and the rectifier diode of the converter, hence switching the LED at high frequencies (>100 kHz). Moreover, a thorough analytical study is carried out for the two topologies proposed in this paper, emphasizing in particular their static analysis and the obtaining of the boundaries between the different conduction modes. Finally, the idea is experimentally validated by means of the boost converter variation (i.e., the DL//S ac-LED driver). The DL//S ac-LED driver was also compared with a dc–dc boost converter, showing a better luminous efficacy while disposing of the Schottky diode and the output capacitor. The analysis was carried out when connected to a Li-ion battery using a simple control and integrated circuit for its development. [ABSTRACT FROM AUTHOR]

Models that accurately predict the output voltage ripple magnitude are essential for applications with stringent performance target for it. Impact of the dc input ripple on the output ripple for a frequency-controlled series resonant converter (SRC) using a discrete-domain exact discretization modeling method is analyzed in this paper. A novel discrete state-space model along with a small-signal model for the SRC considering three state variables is presented. The audiosusceptibility (AS) transfer function that relates the input-to-output ripple is derived from the small-signal model. Analysis of the AS transfer function indicates a resonance peak and an expression is derived connecting the AS resonance frequency for the input ripple based on the SRC component values. Further analysis is done to show that a set of values for the SRC parameter exists, which forms a design space, for which the normalized gain offered by the SRC for the input ripple is less than unity at any input ripple frequency. A test setup to introduce the variable frequency ripple at the input of the SRC for the experimental evaluation of the AS transfer function is developed. Influence of stray parameters on the AS gain, AS resonance frequency, and on the SRC tank resonance frequency is evaluated. An SRC is designed at a power level of 10 kW. The analysis using the derived analytical model, simulations, and experimental results are found to be closely matching. [ABSTRACT FROM AUTHOR]

In a power electronics system, an electrolytic capacitor (E-Cap) is widely used, whose performance degradation can be reflected by the change of capacitance (C) and equivalent series resistance (ESR). This paper proposes a new online C and ESR monitoring scheme for the output electrolytic capacitor in a discontinuous conduction mode (DCM) flyback converter. The mathematical relationship between the instantaneous capacitor voltage and other parameters is analyzed and then the scheme of undetermined coefficients based on the multiple-spot sampling and least square method is further proposed. In addition, considering the particularity of high ripple current and the resultant voltage ripple variation range, especially with the temperature, an inverse ripple voltage isolation amplifier with variable amplification factor and negative voltage elimination is put forward so as to make digital signal processor identify the temperature change easily. The proposed scheme is noninvasive as only voltage signals need to be sampled and no current sensor is necessary. A prototype is built and the experiments are made to verify the effectiveness of the proposed method, from which the data are in accordance with the results measured by an LCR meter. [ABSTRACT FROM AUTHOR]

Taking switching transients of switching devices into consideration in design and simulation of power electronic systems has long been a huge obstacle. Sufficient accuracy has to be ensured, meanwhile more significantly the transient model has to be practical, i.e., providing a convergent result with an acceptable solving speed and a convenient parameter extraction technique. Aiming at both targets, this paper proposes a piecewise analytical transient (PAT) model for switching device commutation unit, taking an IGBT–p-i-n diode pair as an example. A piecewise time-varying voltage source-current source pair is utilized to model the IGBT–p-i-n diode pair. With sufficient accuracy, PAT modeling methodology noticeably increases the solving speed and improves the convergence of converter simulations. Model expressions and datasheet-driven parameter extractions are illustrated in detail. Experimental and simulated results are presented and compared to validate both the accuracy and the practicability of the proposed PAT model, expected to be employed in transient simulations of power electronic systems. [ABSTRACT FROM AUTHOR]

The improved three switch-active clamp forward (3S-ACF) converter is proposed in this paper. The proposed converter has minimized the switching loss on all switches of the conventional 3S-ACF converter by simply changing the gate control method without any additional components. Moreover, the modified gate control enables peak and average currents on the clamp diode to be reduced. Though, all switches of the proposed converter have low-voltage stress similarly to those of the conventional 3S-ACF converter. Consequently, the proposed converter can achieve a high efficiency without any additional components. To confirm the operation, features, and validity of the proposed converter, a 180–288 Vdc input and 12 V/550 W output laboratory prototype is built and tested. [ABSTRACT FROM AUTHOR]