Search

Various methods have been presented in the past to emulate the electrical behavior of modular multilevel converters (MMCs). To meet the demands for the reliability aspect study of MMCs, this paper proposes a viable setup to emulate the thermal behavior and to investigate its feasibility for reliability testing and thermal model validation of the power modules in the MMC. The proposed mission profile emulator has three distinctive features: 1) capable of emulating and measuring the thermal stresses of power modules; 2) capable of implementing practical switching profile as a full-scale MMC; and 3) having significantly reduced requirement for dc power supply compared to existing setups used for electrical studies. Theoretical discussions, and simulations as well as the experimental results are presented to demonstrate the capability of the mission profile emulator both electrically and thermally. Moreover, this paper is accompanied by a video demonstrating how to measure the junction temperature of the power devices using the optical fiber and the thermal camera. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

In this paper, a new non-isolated two-input single-output dc–dc converter with high voltage gain is proposed. In the proposed converter, there are two three-winding coupled inductors used to achieve a high voltage gain and ripple-free input currents. The proposed converter has two switches, and their control pulses are the same as the control pulses of the two-phase interleaved converters with a phase shift equal to $\text{180}^{\circ} $. The voltage stresses of switches and diodes are reduced and are always lower than the high output voltage. The proposed converter is extendable to a four-input single-output converter in which the switches have the control pulses the same as those in four-phase converters with phase shifts equal to $\text{90}^{\circ} $. In this paper, the proposed topology is analyzed in all operating modes, and the values of current and voltage stresses of all switches and diodes, voltage gain, and required conditions for input current ripple cancelation are calculated during a switching period. Finally, the accuracy performance of the proposed converter is reconfirmed through experimental results for 225- and 298-W prototypes. [ABSTRACT FROM AUTHOR]

This paper studies the high power density bidirectional dc–dc converter with interleaving, soft-switching, and near critical conduction mode (near-CRM) operation. Systematic design and control methods are proposed to enhance the effectiveness of passive currents balancing between multiple interleaved phases without using individual phase current feedbacks. This paper first analyzes the zero voltage turn-on operation, including the turn-off energy diversion by the added snubber capacitor and the turn-off resonance models. Second, the intrinsic inverse co-relation between the phase current deviation and the resulting effective duty cycles variation is quantitatively formulated and modeled as a closed-loop mechanism that balances the currents passively. Then, the design constraints of the system parameters including the snubber capacitance, dead time, and valley currents of the near-CRM mode are formulated to guarantee the effectiveness of counteracting the current unbalance. Finally, a variable switching frequency control is proposed to actively control the valley current and maintain the current balancing effectiveness throughout the operating range. An IGBT-based 20-kW three-phase interleaved prototype with the maximum efficiency of 99.1% is constructed to verify the proposed design and control methods. [ABSTRACT FROM AUTHOR]

This paper proposes a novel active-clamp forward converter (ACFC) with a lossless-snubber on the secondary-side, which combines a resonant capacitor and a clamping diode with an output inductor in parallel. The conventional ACFC achieves zero-voltage-switching on switches of the primary-side during dead time for reducing the switching loss and voltage spike. Unfortunately, on the secondary-side of transformer, the voltage spike damages the free-wheeling diode and rectifier diode due to the reverse recovery current and junction-capacitor of the diode and leakage inductance of the transformer. This paper proposes a lossless-snubber on the secondary-side operation for reducing the voltage spike on the free-wheeling diode and forward-rectifier diode. Therefore, the converter proposed in this paper is suitable for high-output-current applications. Experimental results are shown to verify the analysis and design procedure of the proposed forward converter. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

The instantaneous output power of the two-stage single-phase grid-connected photovoltaic (PV) inverter pulsates at twice the line frequency ($2f_{{\text{o}}}$), generating second harmonic current (SHC) in the front-end dc–dc converter and PV panel, which will affect the maximum power point tracking operation and deteriorate the overall conversion efficiency. The generating mechanism of the SHC is analyzed in this paper and it is pointed that in order to eliminate the SHC in the front-end dc–dc converter and PV panel, the voltage loop gain of the front-end dc–dc converter should be high enough at $2f_{{\text{o}}}$. Since there is a −180° phase abrupt at the resonant frequency of the input side filter capacitor and the inductor, the system may be unstable. To cope with this problem, the inductor current feedback active-damping scheme (ADS) is adopted. For further improving the loop gain at $2f_{{\text{o}}}$ , proportional–integral–resonant regulator with ADS (PIR + ADS) is proposed in this paper. Besides, a step-by-step closed-loop parameters design method is presented. Finally, a 3-kW two-stage single-phase grid-connected PV inverter has been fabricated and tested, and the experimental results verify the feasibility of the proposed control schemes. [ABSTRACT FROM AUTHOR]

Light-emitting diodes (LEDs) are solid-state devices with specific $v$ – $i$ characteristics. In this paper, we study the basic requirement of the driving circuits and discuss the proper approach to drive LEDs in view of their characteristics. We compare voltage source driving and current source driving, and discuss their relative advantages and constraints. We specifically introduce the use of circuit duality principle for developing new current-source-mode (CSM) drivers that are less known but are theoretically more versatile compared to their conventional voltage-source-mode counterparts. The study highlights the effects of the choice of driving circuits in terms of the number and size of circuit components used, duty cycle variation, sensitivity of control, nonlinearity and control complexity of LED drivers. We propose a CSM single-inductor multiple-output (SIMO) converter, which demonstrates the advantage of having inductorless and easily controlled current-source drivers, and present a comparison of the CSM SIMO converter with the existing SIMO converters. We further illustrate that a high-voltage-step-down ratio can be naturally achieved by the CSM high-voltage-step-down converter without the use of transformers. This paper presents a systematic and comparative exposition of the circuit theory of driving LEDs, with experimental evidence supporting the major conclusions. [ABSTRACT FROM AUTHOR]

This paper proposes a high-power-density and reliable inverter topology, which transfers the maximum power of a PV array to the load in one power conversion stage. The single-stage power conversion, along with the soft-switching capability of the proposed three-phase PV inverter promises high efficiency at all operating points. Instead of a capacitive dc link that decouples the dc–dc converter and the voltage source inverter in traditional two-stage PV inverters, a high-frequency capacitive ac link is employed in the proposed inverter, which enables exploiting a very small film capacitor, rather than a bulky electrolytic capacitor, for transferring power. Eliminating electrolytic capacitors prolongs the lifetime of this inverter. Considering the long lifetime of PV modules, this feature is of high importance in PV applications. The high-frequency ac link also allows using high-frequency transformers for providing galvanic isolation. Therefore, this inverter is expected to have a very high power density. This paper presents principles of the operation and control, design, and analysis of this inverter, and verifies the performance of the inverter through two prototypes: a 2-kW Si-based prototype and a 2-kW SiC-based prototype operating at different switching frequencies. [ABSTRACT FROM AUTHOR]

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

In this paper, a new soft-switching bridgeless single-phase power factor correction (PFC) converter is presented and analyzed. Employing an auxiliary switch, the input current dead angle that is the main drawback of the existing buck-type PFCs is omitted, and thus, the power factor (PF) is improved, which is the main contribution of the paper. Proposed PFC converter operates under discontinuous conduction mode (DCM) and draws sinusoidal input current from power supply inherently. All switches and diodes are turnedonandoffunder soft switching, which leads to low switching losses and elimination of diode reverse recovery problems. Also, minimum numbers of semiconductor devices are in the power flow path that reduce the conduction losses. A 120-W laboratory prototype is implemented and experimental results verify the validity of theoretical analysis and show efficiency of 92.1%. In addition, total harmonic distortion (THD) of 3.3% is achieved and the input current harmonics complies with IEC61000-3-2 Class D requirements. [ABSTRACT FROM AUTHOR]

Power converters and electric motor drives when tightly regulated behave as constant power loads. These loads are different from resistive loads and have destabilizing negative impedance characteristics, which impact a system's stability. A boost converter is intrinsically nonlinear and is a nonminimum phase system at the output voltage with respect to the control input. The linear approximation of this boost converter loaded with a constant power load has a zero and poles in the right half of the $s$ -plane, making the system unstable and very difficult to control. Control techniques that employ some form of system inversion cannot be implemented for a nonminimum phase system. This paper describes a technique to modify the nonminimum phase boost converter to a minimum phase for a constant power load, further implementing the input–output linearization technique to stabilize the system. This paper also provides a methodological analysis of the problem followed by the proposed solution. Furthermore, it verifies the analysis of the proposed solution through simulation and experimental results. [ABSTRACT FROM AUTHOR]

A high step-up dc–dc converter is proposed in this paper. The presented converter benefits from some advantages such as high voltage gain and continuous input current, which makes it suitable for the renewable energy applications. The presented converter is based on the SEPIC converter. However, the converter voltage gain is improved by employing a coupled inductor and two voltage multipliers. A passive clamp circuit is also added to the proposed converter that increases the voltage gain and reduces the voltage stress on the main switch. Thus, a switch with low $R_{{\text{DS(on)}}}$ will be needed that decreases the conduction loss. Besides, the voltage stress on the output diode in the proposed converter is reduced, which alleviates reverse recovery problem. The steady-state analysis of the proposed converter is discussed in this paper. The analysis is verified with experimental results under the output power of 245 W. [ABSTRACT FROM AUTHOR]

In this paper, a high step-up quasi-Z Source (QZS) dc–dc converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS dc–dc converter while keeping its main advantages, such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch is not increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based dc–dc converters is provided which confirms the superiority of the proposed converter. Simulations are done in power systems computer aided design (PSCAD) in order to investigate the maximum power point tracking (MPPT) capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype. [ABSTRACT FROM AUTHOR]

This paper introduces a new bidirectional single-phase inverter topology. The proposed topology has three ports: a dc port, an ac port, and a ripple port. The ac and dc ports are bidirectional to support rectifier or inverter operation. A small inductor, which is of alternating current, exchanges power between different ports of the single-phase system. The proposed topology is capable of accomplishing voltage step-up or step-down, suppressing the ripple power, and performing inversion or rectification operation in one stage of power conversion. The proposed configuration offers an active decoupling function, which not only eliminates the double-frequency ripple power at the dc port but also achieves minimum capacitance requirements to minimize the size of the decoupling capacitor. This facilitates the use of a very small thin-film capacitor, which offers a much longer life-cycle and higher reliability compared with a bulky electrolytic capacitor. A control approach is also developed to regulate the dc-port and ac-port currents and manage the ripple power through proper distribution of power between each port. Moreover, a very small capacitor can be placed in parallel with the inductor to reinforce the proposed configuration with soft-switching operation, which enhances the overall efficiency and minimizes the voltage stress over the semiconductor devices. This converter is capable of accommodating an arbitrary number of dc or single-phase ac sources and/or loads configuring a multiple-input multiple-output inverter without introducing any additional passive elements or sacrificing the performance of the inverter. The primary focus of this paper is dc-to-ac conversion mode of operation, in spite of the fact that it can easily be configured to serve as a rectifier. Experimental and simulation results are presented to validate the operation of the proposed topology and its control strategy. [ABSTRACT FROM AUTHOR]

Most of the two-stage converters for electric bike battery charging comprise of a boost converter for power factor correction (PFC) followed by a dc–dc converter with universal input voltage. These two-stage conversions suffer from poor efficiency and increased component count. In this paper, a single-stage switched inductor Cuk converter based PFC converter is proposed, which offers high step-down gain, low current stress, high efficiency, and reduced component count. The operational analysis and design equations for various components of the proposed converter are carried out in continuous current mode. This paper presents mathematical modeling, analysis, simulation, and experimentation on the proposed converter rated for 500 W, 48 V/10.4 A. The performance investigation of the proposed converter with respect to power quality indices like voltage total harmonic distortion (THD), current THD, and total power factor is carried out with various types of loads such as resistive load and battery load in both constant voltage (CV) and constant current (CC) mode. Furthermore, the dynamic performance of the proposed converter with battery charging is investigated in CV mode and CC mode with respect to the wide range of supply variations. [ABSTRACT FROM AUTHOR]

Constant on-time V^2 control for point-of-load buck converters has instability issues in the cases that the output capacitors' RC time constants are small. This paper intensively studies the proposed solution using capacitor current ramp compensation, which is a superior solution featuring fast response and universality. A frequency-domain small-signal model based on describing function method is proposed in this paper. The time-domain large-signal response to the load step change is analyzed. The analysis illustrates the unique transient response behaviors of the capacitor current ramp compensated V^2 control. The design optimization methodology based on frequency-domain and time-domain analysis is presented. The proposed model and the design guidelines are verified by the experimental results. [ABSTRACT FROM AUTHOR]

Class $E^2$ DC–DC converter composed of Class $E$ power amplifier (PA) and rectifier is a promising candidate for MHz wireless power transfer. It is soft-switching based and able to achieve high efficiency at MHz frequency. However, the converter implemented through traditional static design is sensitive to the variations of operation condition. Its performance gets deteriorated when DC load and coil coupling deviate from their respective optimum values. This paper demonstrates that the degradation of system efficiency is mostly due to the mismatch of PA load, and the efficiency drop can be efficiently improved by adding an L-type impedance matching network (IMN) after PA. A fixed IMN is sufficient to maintain a high efficiency, while a tunable IMN is required to ensure stable output power when operation condition dramatically changes. Key techniques, particularly system-level optimization, are discussed in this paper that ensure high efficiency over a wide range of variation in operation condition and also with reduced capacitor/inductor tuning ranges in the IMN. The 6.78-MHz Class $E^2$ DC–DC converters with and without the fixed/tunable IMN are fabricated and measured for validation purposes. The experimental results show that both high efficiency ( $>$66%) and stable output power (around 9 W) are maintained for the tunable converter when there are variations in the DC load and coil coupling. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this article, a high-power-density off-line light-emitting diode (LED) driver is proposed. The proposed ac–dc driver is the novel integrated buck and boost converter (IBBC). Besides the high-power-density, the converter shows a high power factor (PF), and a low total harmonic distortion (THD). The IBBC is a two-stage driver that features just one controlled switch, which leads to high PF and low THD operation ensuring high efficiency, and size and cost reduction. Moreover, the switch current is minimized as it conducts the higher of the buck or boost converter, but not the addition of both as in other integrated converters. Moreover, for a further increase of the power-density, a magnetic integration is made by integrating the two inductors of both the buck and boost converters in one core. Thus, the proposed converter has been named as fully integrated buck and boost converter (FIBBC). In this paper, the IBBC is analyzed, and a design methodology is proposed. Also, this article presents a magnetic analysis of the novel FIBBC. In addition, a comparison between two prototypes is presented, one for the IBBC and another for the FIBBC, both of them supplying an LED luminaire of 46 V/ 0.575 A. The FIBBC shows a high PF equal to 0.994, very small THD of 10%, output current ripple of 6%, and efficiency of 92.62%, which represents a landmark on the efficiency of integrated converters. [ABSTRACT FROM AUTHOR]

This paper introduces a non-isolated high step-up dc–dc converter with dual coupled inductors suitable for distributed generation applications. By implementing an input parallel connection, the proposed dc–dc structure inherits shared input current with low ripple, which also requires small capacitive filter at its input. Moreover, this topology can reach high voltage gain by using dual coupled inductors in series connection at the output stage. The proposed converter uses active clamp circuits with a shared clamp capacitor for the main switches. In addition to the active clamp circuit, the leakage energy is recycled to the output by using an integrated regenerative snubber. Indeed, these circuits allow soft-switching conditions, i.e., zero voltage switching and zero current switching for active and passive switching devices, respectively. The mentioned features along with a common ground connection of the input and output make the proposed topology a proper candidate for transformer-less grid-connected photovoltaic systems. The operating performance, analysis and mathematical derivations of the proposed dc–dc converter have been demonstrated in the paper. Moreover, the main features of the proposed converter have been verified through experimental results of a 1-kW laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a procedure for evaluating self-capacitances and parasitic capacitors between physically adjacent turns in multiconductor systems—with a special focus on single-layer air-core inductors. To this end, the paper proposes the use of standard cells, which correspond to a minimal and basic turn, layer, or macrolevel arrangement of a winding in reference to its patterns of stored electrostatic energy. A standard cell embraces mathematical rules derived by means of a curve fitting approach through a set of finite element analysis (FEA) simulations. Besides, it is applied in a matching routine wherein self- and stray capacitances are evaluated according to the relative position of each turn, layer, or macrolevel arrangement along the length of the winding. Finally, the analytical technique is validated by comparing frequency-domain results obtained from an implemented SPICE model and laboratory measurements. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure of nonisolated boost dc–dc converters based on voltage-lift technique is proposed. In comparison with conventional nonisolated boost dc–dc converters, the proposed converter generates higher voltage gain. In this paper, the relations between voltage and current of all elements in continuous conduction mode and discontinuous conduction mode are calculated as well as voltage gain in each mode. Then, the critical inductance and stress of switch current are extracted. Finally, the validity of given theories is examined by using the experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-phase power factor correction (PFC) rectifier to achieve high power factor, wide output voltage range, and ripple power decoupling without using electrolytic capacitors. It consists of two parts: PFC circuit and output voltage regulation circuit. The load side is involved in both parts, which is different from the regular two-stage conversion structure. The proposed rectifier can be directly applied to low voltage cases due to the wide output voltage range. And the decoupling capacitor voltage can be smaller than the peak grid voltage, which reduces the voltage stress. Besides, the low-frequency ripple power buffer is implemented without a dedicated power-buffering controller. This paper first introduces the circuit structure, operation principles, and control method. Then, the system design consideration is given. Finally, the effectiveness of the proposed topology is verified by the simulations and experimental results. [ABSTRACT FROM AUTHOR]

A switched-capacitor-based dual-switch dc–dc converter with a high-boost voltage gain is proposed in this paper. The proposed converter can obtain a high-voltage gain with a small duty cycle, which decreases the voltage stress and the conduction loss on the power switches. This paper presents the key waveforms, the operating principles at the continuous conduction mode and the discontinuous conduction mode, and the parameter design. Moreover, a comparison between the proposed converter and other nonisolated converters has been completed. To verify the operating principle, a 200 W prototype is constructed with an input voltage of 25–50 V and an output voltage of 200 V. The simulation and experimental results are shown. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid nonisolated dc–dc commutation cell, which is generated by the integration between conventional commutation cell and ladder-type passive switched capacitor (SC) cell. From the resulted hybrid cell are derived three different dc–dc converters: a buck-type, a boost-type, and a buck–boost-type. The three structures are analyzed in this paper and are presented the topological stages, static gain characteristics in continuous conduction mode and discontinuous conduction mode, steady-state analysis. The analyses are generalized in relation to the number of switched-capacitor cells employed, which allows the increase of the rated gain of the converters by adding more SC cells. In addition, the proposed hybrid nonisolated dc–dc commutation divides naturally the voltage stress among the semiconductors and capacitors of the power stage. A 1-kW prototype was developed to verify the operation of the three proposed converters and their theoretical analysis. For the buck-type topology, designed with an input voltage of 600 V and output voltage of 450 V, a peak efficiency of 99.2% and efficiency at rated power of 99% were obtained. [ABSTRACT FROM PUBLISHER]

Sheppard–Taylor power factor correction (ST-PFC) rectifier could obtain a high power factor due to its capability of overcoming the control detuning issue. However, it needs a bulky electrolytic capacitor at the load side to buffer the double-frequency ripple power (DFRP), which reduces the reliability and power density significantly. This paper proposes a control method to divert the DFRP to the small energy transfer capacitor. Consequently, the bulky electrolytic capacitor is replaced with a small film capacitor. The proposed method is carried out by introducing the freewheel state (one switch is turned on and the other is turned off) into the control. So no extra hardware is added, which makes the proposed method cost-effective. A low electromagnetic interference emission is also achieved due to the continuous input–output currents. In addition, the proposed method can be extended to other topologies easily. This paper first gives the detailed analysis of the proposed control method, and then introduces the controller design. The selection of the passive components is also briefly discussed. Finally, the simulation and experimental results verify the effectiveness of the proposed control method. [ABSTRACT FROM AUTHOR]

These days, constant on-time current mode (COTCM) control scheme is widely used in the voltage regulator (VR) controllers because it has a higher light-load efficiency and a higher BW design capability while maintaining a simpler compensation requirement. One issue plaguing the COTCM control is its slow transient response which is caused by its fixed TON operation. During the heavy-load step-up transient, the duty cycle becomes saturated and the inductor current increment becomes limited by TON and the minimum off time (TOFF$\_$ MIN) ratio, which can create a large undershoot at load step up. On the other hand, in the load step-down case, if the load step down occurs at the beginning of TON, a large overshoot can be created at the output. To solve this issue, this paper presents a method designed to increase the TON at load step up and then very quickly, decrease at load step down in order to reduce the undershoot and overshoot at output or otherwise save the output capacitor. In this proposed method, the increase or decrease of T ON is proportional to the output change which eliminates the chance of any overcorrection or ring-back problem unlike the methods presented in prior forums. This feature enables the control to work seamlessly in a high-frequency load repetitive case in VR applications. Since this TON change occurs only in the transient period when duty cycle is saturated, it does not affect the small-signal property of the COT control. Moreover, the proposed methods are very much compatible with the state-of-the-art single and multiphase COT control structures. Simulation and test results in both single and multiphase operations are also presented in the paper to verify the proposed concept. [ABSTRACT FROM PUBLISHER]

A novel soft-switching interleaved coupled-inductor boost converter is proposed in this paper. Only a single active soft-switching module is needed to simultaneously achieve the soft-switching property of the two switches in the interleaved coupled-inductor boost converter. The better efficiency is achieved with the less components and cost. The two main switches can achieve the ZVT turn-on and smaller-current turn-off simultaneously when the single active soft-switching module is active. Due to the coupling characteristic of the inductors, the voltages across the two inductors are changed at the same time; therefore, the equivalent circuit is equal to the parasitic capacitors of the two main switches in parallel to resonate with the auxiliary inductor. By coupling two input inductors, the volume and cost of the circuit can be reduced. The interleaved coupled-inductor topology can also reduce the input and output current ripples and share the input and output currents. The operating modes, analysis, and design of the proposed circuit have been discussed in this paper. Simulation and experiments are finally conducted to verify the validity of the proposed circuit. [ABSTRACT FROM PUBLISHER]

DC electric springs (DCES) are emerging technologies for the (i) regulation of mains voltage against the intermittent renewable generations and (ii) harmonic cancellation in dc microgrids. When conventional converter topologies (e.g., half-bridge or full-bridge converter) are adopted as DCES, the battery storage of the DCES has to process both the dc power and the ac harmonic power. The pulsating ac power can severely reduce the lifetime of the battery. To address this issue, a hybrid-DCES (H-DCES) is proposed in this paper to perform (i) and (ii) in a decoupled manner. With a modified topology and control method, the H-DCES can divert the ac current to the ground and retains the function of manipulating noncritical load for dc voltage regulation. The immediate benefits of this H-DCES are the reduction of storage capacity and a prolonged lifetime of the battery. Both the operating principle and the mathematical model of the proposed H-DCES are analyzed in this paper. A prototype of the H-DCES is practically tested in a 48-V dc grid. The experimental results show that the H-DCES can realize the decoupled operation of dc voltage regulation and harmonic cancellation. Simulation studies further demonstrate that the H-DCES requires less storage capacity than its counterparts. [ABSTRACT FROM AUTHOR]

This paper documents a new three-switch, isolated boost dc–dc converter. The major features of the proposed converter are as follows: 1) continuous input current; 2) reduced one active switch, one additional diode, and one additional capacitor; 3) unchanged primary and secondary voltage waveforms of the transformer when the duty cycle is changed; and 4) removal of the snubber circuit. This paper presents the operating principles, analysis, parameter design guidelines, and simulation results for the proposed converter. To verify the performance of the proposed converter, a 400 W prototype was constructed with a 40–60 V dc input. A PID controller was used to maintain the dc output voltage at 400 V. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In high-power applications, parallel operation is required to improve both efficiency and reliability. In an LLC converter, it is difficult to achieve parallel operation due to the gain sensitivity to component tolerance. This paper proposes a new structure of a common resonant capacitor for a multiphase LLC converter, which can achieve very good current-sharing performance with no additional components or control. To evaluate the current-sharing performance, a new first harmonic approximation (FHA) model is built in this paper to analyze the LLC converter with coupled resonant tanks. Both FHA analysis and powersim (PSIM) simulation results demonstrate the load-sharing improvement of the proposed common capacitor LLC resonant converter over the conventional two-phase LLC converter. The current-sharing performance from the FHA analysis and the PSIM simulation are compared, and the error of the FHA analysis is evaluated and explained. A 600 W two-phase LLC converter prototype based on the proposed method is also built to verify the feasibility. Excellent current-sharing performance (6% resonant current sharing error at a wide load range) has been achieved. [ABSTRACT FROM PUBLISHER]

This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter. [ABSTRACT FROM PUBLISHER]

Instead of bulky electrolytic capacitors, active power decoupling circuit can be introduced to a single-phase converter for diverting second harmonic ripple away from its dc source or load. One possible circuit consists of a half-bridge and two capacitors in series for forming a dc-split capacitor, instead of the usual single dc-link capacitor bank. Methods for regulating this power decoupler have earlier been developed, but almost always with equal capacitances assumed for forming the dc-split capacitor, even though it is not realistic in practice. The assumption should, hence, be evaluated more thoroughly, especially when it is shown in the paper that even a slight mismatch can render the power decoupling scheme ineffective and the IEEE 1547 standard to be breached. A more robust compensation scheme is, thus, needed for the dc-split capacitor circuit, as proposed and tested experimentally in the paper. [ABSTRACT FROM AUTHOR]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

Conventional single-phase power-factor-correction (PFC) rectifiers with active power decoupling capability typically require more than three active switches in their circuits. By exploring the concept of power-buffer cell, a new single-stage PFC rectifier with two active switches, one inductor and one small power-buffering capacitor is reported in this paper. The proposed converter can achieve high-power factor, wide output voltage range, and power decoupling function without using electrolytic capacitor. Additionally, an automatic power decoupling control scheme that is simple and easy to implement is proposed in this paper. The operating principle, control method, and design considerations of the proposed rectifier are also provided. A 100-W prototype with ac input voltage of 110 Vrms and a regulated dc output voltage ranging from 30 to 100 V has been successfully designed and practically tested. The experimental results show that with only a 15 μF power-buffering film capacitor, the proposed converter can achieve an input power factor of over 0.98, peak efficiency of 93.9%, and output voltage ripple of less than 3%, at 100-W output power. [ABSTRACT FROM PUBLISHER]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

This article is the continuation of graph sets method (GSM) proposed in the companion paper Part I for deriving equations and analyzing multicoil wireless power transfer multicoil (MC) wireless power transfer (WPT) systems. After explaining GSM, categorizing WPT coils into three different types, and proposing some approximation techniques in Part I, this article, as the second part of this work, presents numerical simulations and experimental results for a three-coil MCWPT system similar to what is explained in Part I. The simulations are conducted in MATLAB/Simulink and ANSYS environments, and for the experimental model, three ferriteless cylindrical coils are built and compensated to behave as voltage driven, current driven, and passive coils, respectively, at the specific frequency of 200 kHz. After analyzing and comparing the simulation and experimental results, it is shown that GSM can be an effective and illustrative technique that facilitates comprehensive analysis of interactions amongst the coils and their characteristics, especially when WPT systems contain multiple coils. [ABSTRACT FROM AUTHOR]

Renewable energy generations have been attracting sustained attentions in academic and industry. Current-fed-isolated-bidirectional dc/dc converters (CF-IBDCs) are widely adopted in low-voltage high-current applications such as solar photovoltaic fuel cell with energy storage. This paper gives an overview and a comprehensive comparative evaluation of CF-IBDCs. The active clamped, dual half-bridge, L-L type dual active bridge, resonant-type, naturally clamped, and other type topologies of CF-IBDCs are investigated, analyzed, and compared regarding their circuit topological structures, operation characteristics, modulation methods, and soft-switching technologies. In addition, component cost models and loss models of converters are deduced and presented. On this basis, quantitative and comprehensive performance comparison of seven typical CF-IBDC topologies selected from each type is conducted in terms of costs, losses, weight, volume, and power density for the given system specifications and design constraints. Finally, the application range of different CF-IBDCs and future trend are presented to encourage further development. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology combining reconfigurability and hybridization is presented. Reconfigurability allows the proposed converter to operate in three different operating modes, yielding a wide range of step-up conversion ratios. The combination of two charge-pump cells and an inductor allows to reduce the average inductor current if compared to a standard equivalent boost converter. A prototype with integrated MOS, drivers, and logic but external passives was built. Experimental results show that with $\mathbf {f_{s} }=\text{300}\,$ kHz, $\mathbf {V_{in} = \text{6}}\,$ V, and $\mathbf {I_o = \text{70}}\,$ mA, the converter can cover conversion ratios in the range from $\text {2.5}$ to $\text {10}$ , with a maximum output voltage equal to $\text {60}\,$ V. Peak efficiency is $\text {91}$ %. When the output current is increased to $\text {100}\,$ mA peak efficiency is $\text {92.8}$ %. [ABSTRACT FROM AUTHOR]

In this paper, a family of new step-up series–parallel dual resonant switched-capacitor converters (SP-DRSCs) is proposed to extend the conversion ratio for high step-up applications. The converters feature a wide gain range, continuously adjustable, and enhanced light-load voltage regulation. All flying capacitors operate in resonance, eliminating high transient current spikes and charge sharing losses. Thus, zero-current-switching (ZCS) turn-on for all transistors and ZCS turn-off for all diodes are achieved. A comprehensive analysis of the operation principle, voltage-gain curves, stable regulation range, and voltage and current stress is given. An analytical method to quantify the passive component volume for the group of step-up dual resonance switched-capacitor converters is presented. Further design considerations to optimize the passive component volume of the proposed SP-DRSC and the effect of bulky bypass capacitors on the volume are discussed. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

This paper presents a pulsed power modulator with a new structure that utilizes the reverse recovery characteristics of diodes to achieve an effective pull-down circuit configuration. The proposed configuration for active pull-down applicable to negative pulsed power applications with a high-voltage direct switching method is implemented by adding a diode to the pulse discharging path of the modulator, instead of using a pull-down resistor. The diode is forward-biased while an output pulse voltage is applied to the load. When the pulse voltage applied to the load is removed, the residual energy in the load is quickly discharged through the reverse recovery path of the diode so that the pull-down function of the pulsed power supply system is efficiently performed. The operating principle of the proposed system is described, and each operating mode is analyzed in detail. In addition, the feasibility of the proposed system configuration is examined through various simulation results. Finally, it is proven that the proposed system can be used effectively in pulsed power application fields through a practical experiment in plasma source ion implantation applications. [ABSTRACT FROM AUTHOR]

DC-to-DC power supplies are critical components for processors in high performance computing and datacenter servers. Conversion from an intermediate bus voltage (e.g., 12 or 48 V) to the core voltage (∼0.9 V) of processors must be efficient, compact, and cost effective. This paper proposes two versions of active-clamp forward converter (ACFC) power blocks to supply core voltage from either 12 or 48 V intermediate bus voltage. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to fit in a standard 1U server. A low loss, compact planar transformer is designed into the ACFC power block printed circuit board (PCB). A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the dc loss in the current path. Thorough analysis is performed to model the conversion loss of the proposed power block. Experimental results show a peak efficiency of 90.4% (12 V input) and 89.5% (48 V input) with 0.9-V output. [ABSTRACT FROM AUTHOR]

This paper introduces the high-frequency link concept into the modular multilevel converter (MMC) topology, which can totally reduce the individual dc-link capacitors at the high-voltage side. The proposed converter, called isolated MMC, has basic triple ports of medium-voltage ac, medium-voltage dc, and low-voltage dc. Thus, it is especially suitable for hybrid dc and ac applications in power generation and transmission, such as solid-state transformer. The fundamental principle and applied control scheme of phase-shift pulsewidth modulation are presented in detail. The design of the voltage clamping circuit and analysis of duty loss are carried out. The experimental results are given to illustrate the efficient operation characteristics. [ABSTRACT FROM AUTHOR]