Search

This letter proposes an indirect power dissipation level short circuit protection (IPDL-SCP) method for silicon carbide (SiC) metal-oxide semiconductor field-effect transistors (mosfets). Due to differences between normal conducting and short-circuit (SC) conditions, this method is triggered by the voltage oscillation vss at the parasitic inductance (Lss) of the source and directly monitoring vds of SiC mosfet. For verification, the short circuit protection circuit is tested and proved functional on the SC test bench. Experimental results show that the protection circuit can respond to both hard switching fault (HSF) and fault under load (FUL), while the fastest response delays are 75 ns for HSF and 170 ns for FUL. Comparisons with other commonly used SC protection methods have also been made, which show that the proposed IPDL-SCP method has better performance in shorter protection delays. [ABSTRACT FROM AUTHOR]

Gate-oxide degradation has been one of the critical reliability concerns of silicon carbide (SiC) metal–oxide–semiconductor-field-effect transistors (mosfets), which could be monitored through aging-sensitive parameters. In this article, an online gate-oxide degradation monitoring method for planar SiC mosfets is proposed by extracting gate charge time at a specific range of gate voltage. It is based on the findings that the input capacitances of planar SiC mosfets change significantly over gate-oxide degradation, which is theoretically analyzed and experimentally verified. The capacitance variations are converted into the gate charge time as the new aging-sensitive parameter. The new parameter measurement circuit is proposed and integrated into the gate driver module. The article results indicate that the new parameter varies noticeably with gate-oxide degradation and the difference of this parameter caused by junction temperature is much smaller than that caused by degradation. Besides, the parameter is immune to package degradation and load current. The condition monitoring method can be implemented online since the parameter is extracted during the off-state of SiC mosfet devices, which does not affect normal operation. The confirmatory experiment is carried out to verify the correctness of the proposed method. [ABSTRACT FROM AUTHOR]

In this article, an efficiency-oriented hybrid duty modulation (HDM) scheme is proposed for the dual active bridge (DAB) converter that can reduce the inductor root-mean-square (rms) current and extend the switch soft-switching range. First, a complete description of the combination forms of different modulation schemes is presented considering the allocation of the zero-voltage portion. A unified description for these combination forms is obtained in the frequency domain. Second, the symmetric–symmetric duty modulation (SSDM) scheme and asymmetric–symmetric duty modulation (A2SDM) scheme are established to minimize the inductor rms current by considering its fundamental component. Third, the characteristics of SSDM, A2SDM, and the traditional phase shift modulation schemes are compared from several aspects, mainly including the inductor rms current and the soft-switching performance. Furthermore, the loss breakdown analysis results for the three modulation schemes are presented and compared. According to these results, the HDM scheme is proposed to improve the overall efficiency of the DAB converter. Finally, an experimental prototype was built with a peak efficiency of 97%, which validates the effectiveness of the proposed modulation scheme. [ABSTRACT FROM AUTHOR]

Monitoring the defective multichip insulated gate bipolar transistor (IGBT) module is a cost-effective approach to improve the quality of customer service. A method using time duration of the gate charge is proposed to monitor bond wires fatigue of the multichip IGBT modules when the modules are in the off-state. It is based on the fact that failure of the chip branch due to bond wires fatigue changes the gate input capacitance of the multichip IGBT module. The health state of bond wires can be converted into the change of time duration of gate charge under the constant gate current. A driver containing the constant current source is proposed. The study results indicate that the time duration of the gate charge decreases significantly when the failure of the chip branch occurs, and the effect of junction temperature can be ignored within the special range of gate voltage. Condition monitoring can be implemented during the off-state of the multichip module and without considering the effects of junction temperature. The confirmatory experiment is carried out to verify the correctness of the proposed method. [ABSTRACT FROM AUTHOR]

Wide bandgap (WBG) devices offer the advantages of high frequency, high efficiency, and high power density to power converters due to their excellent performance. However, their low parasitic capacitance and fast switching speed also make them more susceptible to switching oscillations. The switching oscillations can cause voltage and current overshoots, shoot-through, electromagnetic interference, additional power loss, and even device damage, which can seriously affect the performance of power converters and systems. However, a comprehensive and in-depth overview is lacking on this topic. This article reviews the types, the causes and negative effects, the effects of parasitic parameters and suppression methods of these switching oscillations, which is helpful for practical engineering. First, the switching oscillations are divided into different types, and their causes and negative effects are reviewed. Then, the effects of different parasitic parameters on the switching oscillations are overviewed. It is found that due to the different physical structures of silicon carbide metal-oxide-semiconductor field-effect transistors, enhancement-mode gallium nitride high-electron mobility transistors (eGaN HEMTs), and cascode GaN HEMTs, the effects are also different. Finally, the main methods of suppressing the switching oscillations are summarized, and the advantages and disadvantages of these methods are presented. Furthermore, future research works on this topic and the conclusion of this paper are drawn, which will help readers deepen their understanding of the switching oscillations of WBG devices, and inspire readers to better use WBG devices for high-frequency and high-efficient power conversion. [ABSTRACT FROM AUTHOR]

In order to realize power flow control among photovoltaic (PV) panel port, battery port, and load port in the distributed photovoltaic power generation system, integrated three-port dc–dc converters (TPCs) are widely adopted. The objective of this article is to provide a comprehensive, comparative, and insightful analysis and overview of these TPCs. First, based on the power transmission and control requirements of the system, five topological structures of three-port dc–dc conversion system (TPCS) composed of two or three two-port dc–dc converters are presented. And the five structures are comparatively analyzed. Second, based on these topological structures, and combing with the basic two-port dc–dc converters, three groups of typical TPCs with different galvanic isolation requirements are derived, respectively, by sharing switches, combining branches, etc., And comprehensive analysis, comparisons, and reviews of these TPCs with different structures of each isolation type are presented with tables and figures. Finally, the comparison results of the three isolation groups are summarized, which leads to a guidance for the selection of TPCs in different applications, and then some suggestions for the future research on TPCs are given. [ABSTRACT FROM AUTHOR]

Grid-connected current quality is seriously affected by the low-order background harmonics in the gird-inverter dynamic system. The point of common coupling voltage feedforward impedance reshaping method of the grid-connected inverter is generally applied to solve this problem, however about 90° phase lag of the inverter output impedance is brought in, which would deteriorate the adaptability of the inverter to the weak grid. To solve this problem, this article proposes a novel frequency-division virtual impedance shaping method, which shapes the output impedance of the grid-connected inverter with different coefficients in different frequency bands, respectively. The basic principles, parameters design, and application analysis are studied in detail. With the proposed scheme, the grid-connected inverter can be equipped with strong adaptability to a wide range of grid impedance and suppression ability to the background voltage harmonics simultaneously. Theoretical analysis and experimental results confirm the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Wide bandgap devices such as gallium nitride (GaN) devices are being widely used due to their low on-resistance and parasitic parameters that can improve system performance compared to Si mosfets. However, these advantages mentioned above can sometimes lead to unexpected behavior in practical systems, such as false triggering oscillation. False triggering oscillation may cause overshoot, electromagnetic interference, shoot-through, and even device damage, which seriously affects the performance of the system. In this paper, an RC snubber circuit is proposed to suppress false triggering oscillation in a half-bridge circuit, and the design method of the RC parameters is proposed. The proposed oscillation suppression method is simpler, easier to implement, and more effective than the active gate driver. In addition, it can provide guidance for oscillation suppression design in high-order systems. First, the double pulse circuit is used as an example to analyze false triggering oscillation and its high-frequency equivalent circuit is obtained. Then, the RC region is established by scrutinizing the characteristic equations via a root locus method. The RC snubber circuit has better oscillation suppression effect when the RC parameters are within the region rather than outside the region. Finally, the RC region designed by the proposed method is verified by simulation and experiment results, and the proposed method indicates a substantial improvement of the switching characteristics of the controlled device at turn-off. [ABSTRACT FROM AUTHOR]

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]

In this paper, we propose to monitor the thermal parameters of insulated gate bipolar transistor (IGBT) module using the case temperature. This method works during the shutoff period of IGBT module where the case temperature is in the cooling phase By establishing the relationship between the Cauer-type thermal RC parameters and the time constants of case temperature cooling curves, thermal parameters of the IGBT module can be identified. The proposed method is able to eliminate the influence of thermal interface material (TIM) degradation on the monitored results, which is quite challenging for the current case temperature monitoring methods. Moreover, it enables the detection of thermal resistance and thermal capacitance of the TIM and that of the IGBT module at the same time. Experimental tests are performed to validate the accuracy and feasibility of the proposed method. Moreover, impacts of the junction temperature, case temperature sensing position, and thermal coupling on the monitored results are analyzed. [ABSTRACT FROM AUTHOR]

A single-stage high-frequency resonant ac/ac converter converts the ac-line input voltage into the high-frequency sinusoidal output voltage, which consists of two power conversion units, i.e., a power factor correction (PFC) unit and a high-frequency resonant dc/ac unit, and it can be used to derive a modular multichannel constant current LED driver. By adopting a totem-pole bridgeless PFC boost rectifier to reduce conduction losses, a single-stage bridgeless high-frequency resonant ac/ac converter is proposed in this paper. The operating principle is described, and the performance analysis is presented in detail. Moreover, the quantitative parameter design method of the main circuit is presented, which is suitable for other single-stage ac input converters, such as a single-stage PFC rectifier. Finally, a 130-W prototype has been built and tested to verify the correction of related theoretical analysis and parameter design. [ABSTRACT FROM AUTHOR]

The junction temperature fluctuation of an insulated-gate bipolar transistor (IGBT) is the most important factor of its aging failure, and smoothing the fluctuation is an effective way to improve the life of an IGBT. The existing methods for smoothing the fluctuation by active junction temperature control are not yet ready wide application, and exploring the different approaches to active junction temperature control is a hot topic. This paper presents a method of active junction temperature control that shifts the turn-off trajectory of an IGBT to adjust the IGBT turn-off loss for smoothing the junction temperature. The relationship between parameters of the adjusting circuit and turn-off loss is analyzed. On the basis of this analysis, a method of estimating the smoothing ability for the proposed active junction temperature control is deduced. Using an IGBT installed in a 1.2-MW direct-drive wind power converter as an example, the evaluation result shows that the proposed method can completely smooth the junction temperature fluctuation caused by a 40% rated load fluctuation. Finally, a low-power experiment is carried out. [ABSTRACT FROM PUBLISHER]

Finding and replacing the defective insulated-gate bipolar transistor (IGBT) module timely by monitoring the ageing state of IGBT can improve the reliability of a power converter and reduce the loss caused by IGBT failure. A method for detecting the condition of bond wires in IGBT module by identifying the short-circuit current of IGBT module is presented in this paper. It is based on the fact that parasitic parameters of IGBT module are affected by the local damage induced by ageing over time, and these changes can be easily detected by monitoring the difference of short-circuit current. The study results indicate that short-circuit current of IGBT module decreases with module ageing over time, and the difference of short-circuit current caused by junction temperature is much smaller than that caused by bond wires fatigue on a specific gate driving voltage. Therefore, the IGBT module in the power converter can be diagnosed by detecting the difference of short-circuit current without considering the effects of junction temperature. Finally, a confirmatory experiment is carried out, and the correctness of the method proposed in this paper is verified. [ABSTRACT FROM AUTHOR]

Potential defects inside an insulated gate bipolar transistor (IGBT) module can be seen as precursors of being about to wear out, and are important for health monitoring of the IGBT module which is used to enhance reliability. A method for detecting defects in the IGBT module by identifying dynamic changes of the gate current is presented in this paper. It is based on the fact that parasitic elements inside the IGBT module are affected by local damage induced by aging over time, and subsequently, these influences are easily distinguished by dynamic changes of the gate current. The proposed prognostic approach is based on relevance vector machine framework, which can give accurate predictions and allow operators to observe unhealthy IGBT modules inside a power converter, and then take appropriate measures timely to avoid breakdown. The parasitic elements involved in the gate circuit are extracted, and their contributions to dynamic changes of the gate current are also discussed. Finally, a confirmatory experiment is carried out, and the correctness of the proposed method is verified. [ABSTRACT FROM AUTHOR]

This paper presents a reconfigurable structure dc–dc converter with wide output range and constant peak power (RS-WOCP). This converter is an extension of the traditional isolated dc–dc converter with two output channels by adding an active switch and two diodes. Theoretical analysis indicates that the proposed RS-WOCP converter is able to smoothly reconfigure the output channels in parallel or series to realize wide output voltage range. With this approach, the output voltage is shared equally in the series operating mode and so is the output current in the parallel operating mode. Therefore, the power rating of devices is significantly reduced and the output rectifiers and filters can distribute power losses and thermal stresses. Operating principle, control strategy, modeling, and stability analysis are illustrated in this paper. An experimental prototype of a 200-W DSP-based RS-WOCP converter was built. The experimental results have verified the steady-state performance and fast dynamic response in the whole output voltage range. Comparisons with two close relatives of wide output converters show that the proposed RS-WOCP converter is advantageous for wide output range constant peak power applications. [ABSTRACT FROM AUTHOR]