Search

The fault-tolerant control method of dual three-phase permanent-magnet synchronous motor (PMSM) drives has gained more and more attention in some applications, such as aircraft system and offshore wind energy system. In this letter, the reason for the torque ripple caused by the standard control method has been investigated in view of the frequency domain after the occurrence of a single open-phase fault. Based on the theoretical analysis, a universal control scheme has been proposed for the dual three-phase PMSM drives with two isolated neutral points, which can be implemented under either healthy condition or fault condition. The key is to modify with a closed-loop controller on harmonic subspace with the notch filter. The proposed method not only realizes the seamless transition between two operation conditions without fault diagnosis but also avoids the reconfiguration of the control structure. Moreover, the system optimization of the minimum copper loss under postfault condition has been integrated into the proposed method. The experimental results are presented to illustrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In this article, a fault diagnosis method is proposed to detect current sensor faults for the studied primary permanent-magnet linear motor (PPMLM) traction system, in which only two current sensors are required, and the gain fault and zero-offset fault can be distinguished. In this proposed fault diagnosis method, synchronous currents are estimated by the PPMLM model. By comparing the estimated and measured synchronous currents, estimation errors are calculated, and ac components can be extracted by corresponding filters. In the synchronous frame, the zero-offset fault and the gain fault can be detected by the single-frequency and double-frequency components, respectively. Furthermore, the fault phase also can be located. Compared with conventional fault diagnosis methods, the proposed one can distinguish gain fault and zero-offset fault but only two current sensors are required. Simulation and experimental results verify the effectiveness of the proposed fault diagnosis method. [ABSTRACT FROM AUTHOR]

Aiming at tolerating common electric faults of multiphase motor drives comprehensively and minimizing the adverse impacts from the remedial scheme itself, a diagnosis-free self-healing scheme is put forward for the open-circuit faults of dual three-phase permanent-magnet synchronous motor (PMSM) drives. First, the self-healing mechanisms of dual three-phase PMSM drives are analyzed in detail. On the basis of theoretical analysis, the repressed self-healing capability of the dual three-phase PMSM drives is fully released by optimizing the current references on harmonic subspace. Since the diagnosis process is not required in the proposed self-healing scheme, the misdiagnosis problem and the prolonged damage caused by the additional time cost of diagnosis can be fundamentally avoided. The proposed self-healing scheme can be generally applied to open-switch faults, single open-phase faults, and multiple open-phase faults in the multiphase motor drives. No change is required for the machine model, modulation strategy, or control framework under different open-circuit faults. Thus, the complex transition strategies among different fault-tolerant control methods for different faults can be avoided, and the adverse impacts from the remedial scheme itself can be minimized. Experimental verification is presented to prove the validity of the proposed self-healing scheme. [ABSTRACT FROM AUTHOR]

In this paper, diagnosis and tolerant control schemes have been studied for common electrical faults in T-type three-level inverter fed dual-three phase permanent magnet synchronous motor (PMSM) drives for safety-critical applications. Based on vector space decomposition and double three-phase space vector modulation, diagnostic and tolerant control methods have been developed comprehensively for open-phase faults, open-switch faults, and short-switch faults in T-type three-level inverter fed dual-three-phase PMSM drives, in such way that misdiagnosis of different faults sharing similar faulty features can be avoided. In particular, a two-step diagnostic scheme is proposed in order to simplify the diagnostic process. The first step is to identify the faulty phase and fault category by analyzing current trajectories on harmonic subspace, and the second step is to determine the specific fault type in a small fault-searching area obtained from the first step. In the aspect of fault-tolerant control, a novel current compensation method is proposed for open-phase fault without changing the machine model, space vector diagram, and control framework. Open-switch faults and short-switch faults are tolerated by making full use of the remaining vectors after faults. The validity of the proposed fault diagnosis and tolerance schemes has been verified by experiments. [ABSTRACT FROM AUTHOR]

In this paper, fault diagnosis and fault-tolerant control strategies have been studied comprehensively for dual three-phase permanent-magnet synchronous motor (PMSM) drives to improve the reliability. Based on direct torque control (DTC) with space vector modulation, a series of diagnostic and tolerant control methods have been proposed for five types of faults, namely, speed-sensor fault, dc-link voltage-sensor fault, current-sensor fault, open-phase fault, and open-switch fault. First, diagnosis and tolerant schemes are proposed for speed-sensor fault by estimating the rotor angle speed with the rotating speed of stator flux. Second, diagnosis and tolerant schemes are proposed for dc-link voltage-sensor fault by combining the current model based stator flux observer with the voltage model based stator flux observer. Third, a three-step method is designed to diagnose three types of faults related to current signals, namely, current-sensor fault, open-phase fault, and open-switch fault simultaneously. A vector space decomposition based current estimation method is proposed to achieve fault-tolerant control for the current-sensor fault, and the voltage compensation based fault-tolerant control is presented for both open-phase and open-switch faults. The experiments have been taken on a laboratory prototype to verify the effectiveness of the proposed fault diagnosis and fault-tolerant schemes. [ABSTRACT FROM AUTHOR]