Search

This paper focuses on the development of multilevel hysteresis current regulation strategies. Two such strategies have been discussed and some modifications in their control tasks have been proposed to achieve more reliable and improved performance. In general, the multiband concept has been used while making the proposals. The hysteresis band size considerations have also been presented by taking into account the desired and existing system conditions. The proposed modulation schemes have been applied to a five-level flying-capacitor inverter, whose operation under hysteresis current control mode is much less established. A new method of flying-capacitor voltage balancing is proposed which ensures balanced flying-capacitor voltages and, at the same time, maintains the desired current profile. It uses a time-based approach for controlling the capacitor voltages and achieves appreciable voltage spectrum under wide range of load power factor conditions. The performance of the proposed strategies is confirmed through both simulation and experimental investigations. Index Terms--Flying-capacitor multilevel inverters (FCMLI), flying-capacitor voltage, hysteresis, multilevel inverter, time-based control.

This article proposes a systematic synthesis method to identify the optimum converter topology for a specified voltage conversion ratio. This gain-oriented converter synthesis is formulated as an inverse problem around the inductor flux balance equations. The proposed synthesis method consists of two processes. A set of distinct converter topologies is first synthesized from the specified voltage conversion ratio by obtaining the solutions for a set of six inverse equations in twelve unknowns. The optimal topology for any intended application can be identified based on the desired performance metrics. The complete synthesis method is illustrated with quadratic buck–boost gain as an example. In total, 25 distinct topologies are synthesized using the first process, and their feasibility is validated by PLECS simulation. In total, three case studies are reported to explain the second process. Ground-referenced output and the minimum number of switches are used as the first two selection criteria in all the case studies. Minimum peak inductor current, minimum component stress factor, and minimum voltage and current stress are the third selection criterion in Case Studies-1, 2, and 3, respectively. The steady-state operations of two optimal converters selected in Case Study-1 were verified experimentally. [ABSTRACT FROM AUTHOR]

The inverse problem for the dc–dc converters refers to synthesizing converter topologies from a specified voltage gain expression. Though the flux balance principle is widely used in the analysis of dc–dc converters, its application as a synthesis tool has not been explored. This letter describes a mathematical approach to synthesize converter topologies from a required voltage gain expression by utilizing the principle of inductor flux balance. At first, the general form of gain expression for second-order converters is derived. From the general form of gain expression, the inverse problem is formulated by identifying the governing equations. The mathematical formulation of the inverse problem and highlighting challenges involved in solving it are the primary subjects of this article. To outline these challenges, a probable solution strategy of this inverse problem is presented. In order to derive a converter topology, at first, the appropriate flux balance equations are determined, and then the circuit topology is derived to establish the required flux balance. In contrast to the forward problem, the solution to the inverse problem is neither direct nor unique. Hence, getting the optimum closed-form solution to this inverse problem is an open-ended challenge with many possible approaches. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

Switched boost inverter (SBI) is a single-stage power converter derived from Inverse Watkins Johnson topology. Unlike the traditional buck-type voltage source inverter (VSI), the SBI can produce an ac output voltage that is either greater or less than the available dc input voltage. Also, the SBI exhibits better electromagnetic interference noise immunity when compared to the VSI, which enables compact design of the power converter. Another advantage of SBI is that it can supply both dc and ac loads simultaneously from a single dc input. These features make the SBI suitable for dc nanogrid applications. In this paper, the SBI is proposed as a power electronic interface in dc nanogrid. The structure and advantages of the proposed SBI-based nanogrid are discussed in detail. This paper also presents a dq synchronous-reference-frame-based controller for SBI, which regulates both dc and ac bus voltages of the nanogrid to their respective reference values under steady state as well as under dynamic load variation in the nanogrid. The control system of SBI has been experimentally validated using a 0.5-kW laboratory prototype of the SBI supplying both dc and ac loads simultaneously, and the relevant experimental results are given in this paper. The low cross regulation and the dynamic performance of the control system have also been verified experimentally for a 20% step change in either dc or ac load of SBI. These experimental results confirm the suitability of the SBI and its closed-loop control strategy for dc nanogrid applications. [ABSTRACT FROM AUTHOR]

The flying capacitor multicell inverter (FCMI) possesses natural balancing property. With the phase-shifted carrier-based scheme, natural balancing can be achieved in a straightforward manner. However, to achieve natural balancing with the harmonically optimal phase-disposition (PD) carrier-based scheme, the conventional approaches require (n − 1) × (n − 1) trapezoidal carrier signals for an n-level inverter, which is ( n − 1) × (n − 2) times more than that in the standard PD scheme. This paper proposes two improved natural balancing strategies for FCMI under PD scheme, which use the same (n − 1) carrier signals as used in the standard PD scheme. In the first scheme, the on-line detections are performed of (i) the band in which the modulation signal is located, (ii) corresponding period number of the carrier, and (iii) rising or falling half cycle of the carrier waveform to generate the switching signals based on certain rules. In the second strategy, the output voltage level selection is first processed and the switching signals are then generated according to a rule based on preferential cell selection algorithm. These methods are easy to use and can be simply implemented as compared to the other available methods. Simulation and experimental results are presented for a five-level inverter to verify these proposed schemes. [ABSTRACT FROM AUTHOR]

The hysteresis modulation for power electronic converters is attractive in many different applications because of its unmatched dynamic response and wide command-tracking bandwidth. Its application and benefits for two-level converters are well understood, but the extension of this strategy to multilevel converters is still under development. This paper summarizes and reviews the various hysteresis modulation approaches available in the literature for multilevel converters. The pros and cons of various techniques are described and compared for tracking the reference signal in order to attain an adequate switching optimization, excellent dynamic responses and high accuracy in steady-state operation. By using the recently developed multilevel hysteresis modulation approaches, the advantages of using several accessible dc potentials in a multilevel inverter have been fully exploited. All of these hysteresis modulation approaches are tested for tracking a current reference when applied to a five-level inverter. The relevant simulation and experimental results are also presented. This study will provide a useful framework and point of reference for the future development of hysteresis modulation for multilevel converters. [ABSTRACT FROM AUTHOR]

This paper focuses on the development of multilevel hysteresis current regulation strategies. Two such strategies have been discussed and some modifications in their control tasks have been proposed to achieve more reliable and improved performance. In general, the multiband concept has been used while making the proposals. The hysteresis band size considerations have also been presented by taking into account the desired and existing system conditions. The proposed modulation schemes have been applied to a five-level flying-capacitor inverter, whose operation under hysteresis current control mode is much less established. A new method of flying-capacitor voltage balancing is proposed which ensures balanced flying-capacitor voltages and, at the same time, maintains the desired current profile. It uses a time-based approach for controlling the capacitor voltages and achieves appreciable voltage spectrum under wide range of load power factor conditions. The performance of the proposed strategies is confirmed through both simulation and experimental investigations. [ABSTRACT FROM AUTHOR]