Search

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

This paper proposes a high-power-density and reliable inverter topology, which transfers the maximum power of a PV array to the load in one power conversion stage. The single-stage power conversion, along with the soft-switching capability of the proposed three-phase PV inverter promises high efficiency at all operating points. Instead of a capacitive dc link that decouples the dc–dc converter and the voltage source inverter in traditional two-stage PV inverters, a high-frequency capacitive ac link is employed in the proposed inverter, which enables exploiting a very small film capacitor, rather than a bulky electrolytic capacitor, for transferring power. Eliminating electrolytic capacitors prolongs the lifetime of this inverter. Considering the long lifetime of PV modules, this feature is of high importance in PV applications. The high-frequency ac link also allows using high-frequency transformers for providing galvanic isolation. Therefore, this inverter is expected to have a very high power density. This paper presents principles of the operation and control, design, and analysis of this inverter, and verifies the performance of the inverter through two prototypes: a 2-kW Si-based prototype and a 2-kW SiC-based prototype operating at different switching frequencies. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper introduces a new bidirectional single-phase inverter topology. The proposed topology has three ports: a dc port, an ac port, and a ripple port. The ac and dc ports are bidirectional to support rectifier or inverter operation. A small inductor, which is of alternating current, exchanges power between different ports of the single-phase system. The proposed topology is capable of accomplishing voltage step-up or step-down, suppressing the ripple power, and performing inversion or rectification operation in one stage of power conversion. The proposed configuration offers an active decoupling function, which not only eliminates the double-frequency ripple power at the dc port but also achieves minimum capacitance requirements to minimize the size of the decoupling capacitor. This facilitates the use of a very small thin-film capacitor, which offers a much longer life-cycle and higher reliability compared with a bulky electrolytic capacitor. A control approach is also developed to regulate the dc-port and ac-port currents and manage the ripple power through proper distribution of power between each port. Moreover, a very small capacitor can be placed in parallel with the inductor to reinforce the proposed configuration with soft-switching operation, which enhances the overall efficiency and minimizes the voltage stress over the semiconductor devices. This converter is capable of accommodating an arbitrary number of dc or single-phase ac sources and/or loads configuring a multiple-input multiple-output inverter without introducing any additional passive elements or sacrificing the performance of the inverter. The primary focus of this paper is dc-to-ac conversion mode of operation, in spite of the fact that it can easily be configured to serve as a rectifier. Experimental and simulation results are presented to validate the operation of the proposed topology and its control strategy. [ABSTRACT FROM AUTHOR]

Most of the two-stage converters for electric bike battery charging comprise of a boost converter for power factor correction (PFC) followed by a dc–dc converter with universal input voltage. These two-stage conversions suffer from poor efficiency and increased component count. In this paper, a single-stage switched inductor Cuk converter based PFC converter is proposed, which offers high step-down gain, low current stress, high efficiency, and reduced component count. The operational analysis and design equations for various components of the proposed converter are carried out in continuous current mode. This paper presents mathematical modeling, analysis, simulation, and experimentation on the proposed converter rated for 500 W, 48 V/10.4 A. The performance investigation of the proposed converter with respect to power quality indices like voltage total harmonic distortion (THD), current THD, and total power factor is carried out with various types of loads such as resistive load and battery load in both constant voltage (CV) and constant current (CC) mode. Furthermore, the dynamic performance of the proposed converter with battery charging is investigated in CV mode and CC mode with respect to the wide range of supply variations. [ABSTRACT FROM AUTHOR]

A switched-capacitor-based dual-switch dc–dc converter with a high-boost voltage gain is proposed in this paper. The proposed converter can obtain a high-voltage gain with a small duty cycle, which decreases the voltage stress and the conduction loss on the power switches. This paper presents the key waveforms, the operating principles at the continuous conduction mode and the discontinuous conduction mode, and the parameter design. Moreover, a comparison between the proposed converter and other nonisolated converters has been completed. To verify the operating principle, a 200 W prototype is constructed with an input voltage of 25–50 V and an output voltage of 200 V. The simulation and experimental results are shown. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid nonisolated dc–dc commutation cell, which is generated by the integration between conventional commutation cell and ladder-type passive switched capacitor (SC) cell. From the resulted hybrid cell are derived three different dc–dc converters: a buck-type, a boost-type, and a buck–boost-type. The three structures are analyzed in this paper and are presented the topological stages, static gain characteristics in continuous conduction mode and discontinuous conduction mode, steady-state analysis. The analyses are generalized in relation to the number of switched-capacitor cells employed, which allows the increase of the rated gain of the converters by adding more SC cells. In addition, the proposed hybrid nonisolated dc–dc commutation divides naturally the voltage stress among the semiconductors and capacitors of the power stage. A 1-kW prototype was developed to verify the operation of the three proposed converters and their theoretical analysis. For the buck-type topology, designed with an input voltage of 600 V and output voltage of 450 V, a peak efficiency of 99.2% and efficiency at rated power of 99% were obtained. [ABSTRACT FROM PUBLISHER]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

Renewable energy generations have been attracting sustained attentions in academic and industry. Current-fed-isolated-bidirectional dc/dc converters (CF-IBDCs) are widely adopted in low-voltage high-current applications such as solar photovoltaic fuel cell with energy storage. This paper gives an overview and a comprehensive comparative evaluation of CF-IBDCs. The active clamped, dual half-bridge, L-L type dual active bridge, resonant-type, naturally clamped, and other type topologies of CF-IBDCs are investigated, analyzed, and compared regarding their circuit topological structures, operation characteristics, modulation methods, and soft-switching technologies. In addition, component cost models and loss models of converters are deduced and presented. On this basis, quantitative and comprehensive performance comparison of seven typical CF-IBDC topologies selected from each type is conducted in terms of costs, losses, weight, volume, and power density for the given system specifications and design constraints. Finally, the application range of different CF-IBDCs and future trend are presented to encourage further development. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology combining reconfigurability and hybridization is presented. Reconfigurability allows the proposed converter to operate in three different operating modes, yielding a wide range of step-up conversion ratios. The combination of two charge-pump cells and an inductor allows to reduce the average inductor current if compared to a standard equivalent boost converter. A prototype with integrated MOS, drivers, and logic but external passives was built. Experimental results show that with $\mathbf {f_{s} }=\text{300}\,$ kHz, $\mathbf {V_{in} = \text{6}}\,$ V, and $\mathbf {I_o = \text{70}}\,$ mA, the converter can cover conversion ratios in the range from $\text {2.5}$ to $\text {10}$ , with a maximum output voltage equal to $\text {60}\,$ V. Peak efficiency is $\text {91}$ %. When the output current is increased to $\text {100}\,$ mA peak efficiency is $\text {92.8}$ %. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

This paper introduces the high-frequency link concept into the modular multilevel converter (MMC) topology, which can totally reduce the individual dc-link capacitors at the high-voltage side. The proposed converter, called isolated MMC, has basic triple ports of medium-voltage ac, medium-voltage dc, and low-voltage dc. Thus, it is especially suitable for hybrid dc and ac applications in power generation and transmission, such as solid-state transformer. The fundamental principle and applied control scheme of phase-shift pulsewidth modulation are presented in detail. The design of the voltage clamping circuit and analysis of duty loss are carried out. The experimental results are given to illustrate the efficient operation characteristics. [ABSTRACT FROM AUTHOR]

In this paper, a dual half-bridge LLC resonant converter with magnetic control is proposed for the battery charger application. The primary switches are shared by two LLC resonant networks, and their outputs are connected in series. One of the LLC resonant converters is designed to operate at the series resonant frequency, which is also the highest efficiency operating point, and the constant output voltage characteristic is achieved at this operating point. The second LLC resonant converter adopts magnetic control to regulate the total output current and voltage during both constant current charge mode and constant voltage charge mode. Meanwhile, the function decoupling idea is adopted to further improve the system efficiency. The significant amount of the power is handled by the LLC resonant converter operating at the series resonant frequency, whereas the second LLC resonant converter fulfills the responsibility to achieve closed-loop control. By carefully designing the resonant networks, the zero-voltage switching for primary switches and zero-current switching for secondary diodes can be achieved for whole operation range. A 320-W experimental prototype is built to verify the theoretical analysis, and the maximum efficiency is measured about 95.5%. [ABSTRACT FROM AUTHOR]

The Cuk dual resonance core (DRC) realizes overlapped dual resonance to regulate its output voltage. However, the DRC configuration was only applied to the Fibonacci switched-capacitor converter (SCC), series–parallel SCC, and voltage doubler. In this paper, the Cuk DRC is modified and then is extended to the Dickson SCC to form a multi-resonance-core-based (MRC) Dickson resonant switched-capacitor converter. All charging and discharging loops achieve soft charging, and so the inherent capacitor charge sharing loss and the high current transient spikes are eliminated. The modular configuration makes the MRC Dickson easy to be extended to a higher voltage level. The on-time fixed frequency modulation is adopted, all transistors being turned on with zero-current-switching (ZCS) operation and all diodes being turned off with ZCS operation. Most importantly, the conversion ratio of the MRC Dickson can be regulated continuously, widely, and efficiently even at light load condition, which is a huge advantage over the traditional Dickson SCC with limited control headroom. A comprehensive analysis of the operation principle, voltage-gain curve, component stress analysis, and output characteristic is provided. The converter operation principle and regulation capability were verified by both simulation and experiment. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

This paper presents a new bridgeless buck–boost power factor corrector with the use of the active virtual ground technique, which is named as the Manitoba Rectifier. The proposed topology can convert the grid ac voltage into a wide range of voltage outputs within a single-stage circuit. It is in a bridgeless structure and simple in design. During the operation, an LC filter is generated at the system input, where continuous grid current is guaranteed in a buck–boost characteristic topology. In addition, the filter capacitor helps to clamp the voltage ripple between the grid and the output bus terminal. Both leakage current and common mode noise are kept in a relatively small value. Thus, a single-stage and low common-mode buck–boost converter system is built. The proposed topology is successfully implemented on an 800 W prototype, and the performance is experimentally verified, which shows good agreement with the theoretical findings. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Due to its simplicity, the hard-switching boost converter is widely used in many applications, such as renewable energy and power factor correction. The power density of the converter can be increased with smaller magnetics; however, this requires an increase in the switching frequency. Therefore, it is necessary to provide soft-switching conditions to minimize the switching losses. In this paper, a new resonant step-up converter and the associated analysis are presented. The proposed interleaved LC resonant boost converter provides soft switching for all of the semiconductor elements even under light loading conditions. Small inductors with discontinuous conduction mode (DCM) currents can be used because the interleaving behavior ensures a continuous input current with low ripples. The interleaving also reduces the output capacitor ripple current. Burst mode operation has been applied to improve the efficiency of the converter during light loading conditions. Detailed design methodology and the control strategies are provided. To show the validity of the theoretical analysis, experimental results are provided for a 400-W prototype, and are compared to a benchmark conventional interleaved boost converter with the same components. Substantial efficiency improvements are achieved for different loads and voltage gains, particularly under light loading conditions. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage single-switch soft-switching (S6) power factor correction (PFC) converter to enhance the current shaping performance and reduce the total harmonic distortion. This improvement is achieved by the aid of an auxiliary winding which is used to lower the input current harmonics and also achieve soft-switching condition. As a result, the switching losses are reduced and harmonic content of the input current is improved noticeably in comparison to the conventional S6 PFC converter. Also, the total number of semiconductor elements is reduced in the proposed topology which results in lower cost and higher efficiency. The operating modes of the proposed converter are discussed in detail and the design procedure is presented. A 200-kHz prototype of the proposed converter is implemented and the obtained results are provided to verify the converter theoretical analysis and operation. [ABSTRACT FROM AUTHOR]

Modules with series and parallel connectivity add new features and operation modes to modular multilevel converters (MMCs). Compared to full- and half-bridges, the series/parallel modules allow sensorless module balancing and reduce conduction loss with the same semiconductor area. However, in high-voltage applications with limited switching rates, the sensorless operation of the series/parallel modules suffers from large charge-balancing currents. This paper introduces a series/parallel module variant with a small port inductor. The port inductor suppresses the charge-balancing current despite low switching rates. We also propose a carrier-based modulation framework and show the importance of the carrier assignment in terms of efficiency and balancing. The proposed module and the modulation method are verified on a lab setup with module switching rates down to 200 Hz. The module voltages are kept within a narrow band with the charge-balancing currents below 5% of the arm current. The experimental results show practicality and advantages of the new series/parallel modules in high-voltage MMC applications. [ABSTRACT FROM AUTHOR]

There have been several advanced topologies proposed by the community for micro-inverter applications. However, many such applications suffer from unwanted second-order harmonic current ripple at dc input. Moreover, in the absence of suitable passive filter or ripple compensator, the second-order harmonics ripple may propagate into the dc source. This results in several problems to the system, related to system efficiency, life, cost, size, reliability, and stability. This paper proposes an adaptive sliding-mode controller to shape the output impedance of the boost-circuit of quasi-switched boost inverter such that the propagation of the ripple from dc link to the dc-input source is resisted. The quasi-switched boost inverter is one of the advanced and suitable topologies for the micro-inverter applications. The adaptive nature of the proposed controller improves the transient performance of the system at the line–load transients unlike some existing solutions, which affects dynamics adversely to achieve ripple mitigation objective. The controller ensures voltage regulation within ${5\%}$ at dc link. The proposed control technique is verified using a lab-prototype of 500 W quasi-switched boost inverter. [ABSTRACT FROM AUTHOR]

In the context of reducing total CO $_2$ emissions as well as reducing the total copper cable length and weight on cars, automotive manufacturers propose to derive all the supply voltages from a single $\text{48 V}$ bus through high step-down ratio dc–dc converters. The series capacitor tapped inductor (SCTI) converter is a promising topology for efficient single-stage step-down conversion from the $\text{48 V}$ bus. In the synchronous version of the SCTI, however, turn-off of the synchronous rectifier at positive drain-to-source current leads to a voltage spike and to a potential catastrophic failure of the converter. In this paper, a simple control technique is proposed, which prevents the foregoing condition to occur. The approach enables a reliable operation of the synchronous SCTI topology without disrupting its main features and advantages, and eliminating the need for additional snubbers, voltage clamps or auxiliary windings. The approach is validated via computer simulations and experimental tests on a $\text{48}$ -to- $\text{1.5}\;\text{V}$ , $\text{4 A}$ SCTI converter prototype. [ABSTRACT FROM AUTHOR]

This paper investigates basic stability properties of the three-level flying-capacitor Buck converter when operated under current-mode control (CMC). The proposed analysis is developed for both peak CMC (P-CMC) and valley CMC (V-CMC), and addresses both the static instability of the inductor current and the flying capacitor (FC) voltage runaway phenomenon. Conditions for avoiding current subharmonic oscillations are derived first, along with the expressions of the minimal compensation ramp, which guarantee current stability throughout the entire operating range. As for the stability of the FC voltage, P-CMC results to be inherently unstable unless the converter operates with a relatively large peak-to-peak inductor-current ripple, a feature not yet recognized in the literature. However, V-CMC results to be inherently stable once the static instability of the current is eliminated with an external compensating ramp—a property that has been highlighted in the literature but never formally proven. The proposed analysis is verified both using a simulation model and experimentally using a 3.3-V, 500-mA, 500-kHz prototype. [ABSTRACT FROM AUTHOR]

Impedance-source networks are an increasingly popular solution in power converter applications, especially in single-stage buck–boost power conversion to avoid additional front-end dc–dc power converters. In the survey papers published, no analytical comparisons of different topologies have been described, which makes it difficult to choose the best option. Thus, the aim of this paper is to present a comprehensive analytical comparison of the impedance-source-based buck–boost inverters in terms of passive component count and semiconductor stress. Based on the waveform of the input current, i.e., with or without a transformer, and with or without inductor coupling, the impedance-source converters are classified. The main criterion in our comprehensive comparison is the energy stored in the passive elements, which is considered both under constant and predefined high frequency current ripple in the inductors and the voltage ripple across the capacitors. Two-level and multilevel solutions are described. The conclusions provide a “one-stop” information source and a selection guide of impedance-source-based buck–boost inverters for different applications. [ABSTRACT FROM PUBLISHER]

In this paper, the Z-source converter is introduced to power factor correction (PFC) applications. The concept is demonstrated through a wireless power transfer (WPT) system for electric vehicle battery charging, namely Z-source resonant converter (ZSRC). Due to the Z-source network (ZSN), the ZSRC inherently performs PFC and regulate the system output voltage simultaneously, without adding extra semiconductor devices and control circuitry to the conventional WPT system such as conventional PFC converters do. In other words, the ZSN can be categorized as a family of the single-stage PFC converters. In addition, the ZSN is suitable for high-power applications since it is immune to shoot-through states, which increases reliability and adds a boost feature to the system. The ZSRC-based WPT system operating principle is described and analyzed in this paper. Simulations and experimental results based on a 1-kW prototype with 20-cm air gap between the system primary and secondary sides are presented to validate the analysis and demonstrate the effectiveness of the ZSN in the PFC of the WPT system. [ABSTRACT FROM PUBLISHER]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

This paper presents a novel interleaved high-conversion-ratio bidirectional dc–dc converter based on switched capacitors and coupled inductors. Series-connected switched capacitor and inductor cells were used to increase the voltage conversion ratio, reduce voltage stresses on power switches, realize soft-charging/discharging of switched capacitors, and achieve autocurrent-sharing in parallel inductors. The interleaved structure combined with switched capacitors was adopted to reduce current ripple at the side having lower voltage, thus enabling applications that require high power levels. In this paper, we first review the status of high-voltage-ratio bidirectional dc–dc converters. Then, the evolution of the proposed extensible topologies and the steady-state operating principle under the inductor current continuous conduction mode is presented. Finally, the performance and features such as voltage gain, voltage and current stress, and the autocurrent-sharing mechanism that are realized by switched capacitors are verified; the optimal design of coupled-inductors, switched-capacitors, and the chip size of switches are given. A specific design of the driving circuit that facilitates actual applications is described. A 1-kW prototype converter, employing a hybrid configuration of SiC and Si mosfets, was constructed to verify the theoretical analysis, and achieved an optimal compromise between conversion efficiency and low cost. [ABSTRACT FROM AUTHOR]

High step-down dc/dc converters are widely utilized in telecom and modern industrial applications. Due to the high step-down ratio, conventional Buck converter cannot provide satisfactory performance. To solve this problem, quite a few new topologies have been proposed to improve the performance of high step-down dc/dc converters, such as series-capacitor Buck (SC-Buck) converter, 3-level Buck converters, tapped inductor Buck converters, and LLC resonant converters. In this paper, the twice step-down benefit of SC-Buck converter and the zero-voltage switching benefit of series-capacitor tapped Buck (SC-TaB) converter are combined together to propose a new topology: interleaved series-capacitor tapped Buck (ISC-TaB) converter. To analyze the performance of the proposed ISC-TaB converter, the operation principles are discussed and the voltage conversion ratio is derived. In addition, to guide the design procedure and optimization, the current waveforms and voltage waveforms of the proposed ISC-TaB are derived. In order to verify the performance of the proposed ISC-TaB, hardware prototype of the proposed ISC-TaB converter and conventional two-phase series-capacitor tapped Buck converter (2ph-TaB) are designed and tested. The application is targeted at telecom with 48-V input and 3.3 V/20 A output. The test results are compared between these two converters. A peak efficiency of 95.6% is achieved on the proposed ISC-TaB and the efficiency of the ISC-TaB over all load range is at least 1% higher than that of 2ph-TaB. [ABSTRACT FROM AUTHOR]

This paper presents a new class of switched tank converters (abbreviated as STCs) for high-efficiency high-density nonisolated dc–dc applications where large voltage step down (up) ratios are required. Distinguished from switched capacitor converters, the STCs uniquely employ LC resonant tanks to partially replace the flying capacitors for energy transfer. Full soft charging, soft switching, and minimal device voltage stresses are achieved under all operating conditions. The STCs feature very high efficiency, power density, and robustness against component nonidealities over a wide range of operating conditions. Furthermore, thanks to the full resonant operation, multiple STCs can operate in parallel with inherent droop current sharing, offering the best scalability and control simplicity. These attributes make STC a disruptive and robust technology viable for industry's high volume adoption. A novel equivalent DCX building block principle is introduced to simplify the analysis of STC. A 98.9% efficiency STC product evaluation board (4-to-1, 650 W) has been developed and demonstrated for the next-generation of 48-V bus conversion for data center servers. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a modular multilevel series/parallel converter (MMSPC) with intermodule switched-inductor power transfer. The switched-inductor voltage conversion feature allows controllable and efficient transfer of energy between modules with nonnegligible voltage difference, providing both step-down and step-up functionalities. Thus, this converter can accurately control and rapidly adjust the voltage of each module to generate an ac output voltage waveform with a controllable number of levels, increasing the quality of the output. Moreover, the intrinsic dc–dc conversion feature can generate a dc controllable output voltage and enable new applications. In this text, we specifically demonstrate how the flexibility of obtaining both ac and dc output with the same setup renders the topology promising for battery energy storage systems and dc microgrid applications. Experimental results validate the topology and concept of an MMSPC with intrinsic switched-inductor conversion. [ABSTRACT FROM AUTHOR]

This paper explores the use of the flying-capacitor multilevel (FCML) topology in high step-up conversion. Compared to the conventional two-level boost converter, the FCML topology utilizes high energy density capacitors to facilitate inductors with storing and transferring energy during the conversion process, which brings features, such as lower voltage stress on the switches, reduced voltage stress on the inductor, and high effective switching frequency at the switching node. As a result, the total volume of the passive components in the converter is greatly reduced while maintaining high efficiency at high voltage gain. To demonstrate the potential high power density and high efficiency, a hardware prototype that converts 100 V to 1 kV with 820-W maximum output power is built. Such specifications require careful optimizations in many aspects of the converter to ensure a high power density and efficiency design. The implemented solutions and associate design process are presented in detail, with comparison with other state-of-the-art solutions. The hardware prototype has successfully demonstrated a peak efficiency of 94.1%, and 329 W/in $^3$ (20 W/cm $^3$) overall power density. [ABSTRACT FROM AUTHOR]

Energy balancing of the alternate arm converter (AAC) is a major challenge and overlap period-based circulating current control methods are commonly used. Component parameter variation occurs due to tolerances, component aging, and internal faults leading to stored energy imbalances of modular voltage source converter (VSC) topologies. If not controlled, such variations can severely impact the operation of the AAC. Hence, component parameter variation is a key consideration for energy balancing of all sorts of modular VSC topologies, but has not been addressed in the existing literature for the AAC. This paper investigates the energy balancing capability of the AAC in high-voltage direct current (HVDC) applications under component parameter variations and proposes a compensation method to further improve its energy balancing performance. The effectiveness of the proposed method is verified in a real-time model of an AAC-HVDC transmission system from widely accepted existing CIGRE benchmark models. [ABSTRACT FROM AUTHOR]

The paper presents a new transformerless single-phase single-stage buck–boost grid-connected voltage source inverter (VSI) topology. The topology can achieve efficient power conversion with a wide input voltage range, number of magnetic devices reduction and low leakage current. The proposed VSI topology consists of high frequency semiconductors for shaping inductor currents, and low frequency semiconductors to form grid CL filter structure for different conditions. This CL filter uses the same buck–boost inductor, thus no additional line frequency inductor is required. Besides, common mode voltage, a main problem of transformerless grid-connected VSI, is mitigated, since the capacitor in the CL filter clamps the voltage between the grid and the bus terminal. The performance of the proposed VSI is experimentally verified. The results show that the proposed VSI guarantees sinusoidal output current and wide input voltage range, and has a good agreement with the theoretical findings. [ABSTRACT FROM AUTHOR]

This paper presents three nonisolated high voltage gain dc–dc converters with ripple-free input current. The proposed converters combine coupled inductors and voltage-doubler structure (VDS) to achieve high step-up of input voltage. An active clamp circuit is used to suppress voltage spike of the switch caused by of the leakage inductor of the coupled inductor. VDS is placed in the secondary winding of the coupled inductor that clamps the diodes voltage stress. Working principle and design methodology of the proposed converters are presented in detail. Experimental results for a 300 W laboratory prototype, 48 V input voltage, and regulated output voltage of 400 V, are shown to validate the operation of proposed converters. [ABSTRACT FROM AUTHOR]

Applications such as renewable energy generation, electric vehicles, and low-power UPS require single-phase ac/dc conversion. However, this conversion introduces a considerable amount of second-harmonic ripple on the dc link. If not filtered, this distortion hinders the converter's performance as well as the energy quality on both the ac and dc side. To mitigate this problem, a large electrolytic capacitor is usually the solution of choice, which mitigates the voltage ripple, but has drawbacks of its own, including the increased size and cost associated with the large capacitance and the limited lifespan of electrolytic capacitors. Alternative solutions to the problem include integration of an active filter circuit to the converter, which can utilize a storage element with the objective of mitigating power ripple. Such solutions have often been proposed alongside a control system, which is either highly complex or relies on open-loop feedforward techniques. This paper presents a control system, which adapts the single-input space vector concept for a single-phase application and leverages its simplicity and closed-loop architecture, allowing the controller to perform well in the presence of disturbances and parameter uncertainty. Experimental results are provided to elucidate the controller's performance on a single-phase grid-connected photovoltaic array application. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

Cascaded multilevel inverter (CMI) is one of the most popular multilevel inverter topologies. This topology is synthesized with some series-connected identical H-bridge cells. CMI requires several isolated dc sources which brings about some difficulties when dealing with this type of inverter. This paper addresses the problem by proposing a switched-capacitor (SC)-based CMI. The proposed topology, which is referred to as switched-capacitor single-source CMI (SCSS-CMI), makes use of some capacitors instead of the dc sources. Hence, it requires only one dc source to charge the employed capacitors. Usually, the capacitor charging process in a SC cell is companied by some current spikes which extremely harm the charging switch and the capacitor. The capacitors in SCSS-CMI are charged through a simple auxiliary circuit which eradicates the mentioned current spikes and provides zero-current switching condition for the charging switch. A computer-aid simulated model along with a laboratory-built prototype is adopted to assess the performances of SCSS-CMI, under different conditions. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

This paper presents an overview of resonant and hybrid switched-capacitor converters with a particular focus on multimode operation. The multimode approach is discussed as a tool to affect high efficiency and power density across a wide load range, provide variable regulation, and, as a general framework, to conceptualize the advantages and opportunities of the approach compared to more traditional dc–dc converters. A general analysis is provided to quantify the advantage of hybrid and resonant converters that factors in the tradeoffs between size and loss in the magnetic component and voltage stress on the active devices. A broader set of operating modes is presented that spans continuous and discontinuous conduction and includes resonant, quasi-resonant, and more traditional buck- or boost-like operation. A prototype flying-capacitor multilevel converter is presented to demonstrate the variety of operating modes and motivate important considerations such as voltage balance on the flying capacitors. [ABSTRACT FROM AUTHOR]

The double-sided LCC topology provides a highly efficient compensation method for electric vehicle (EV) wireless charging systems. However, the two compensated coils occupy a large volume. In order to address the volume increase as well as to be compatible with unipolar coil structures, which are widely applied in EV wireless charging systems, an integration method is introduced in this paper. Aspect ratios of the compensated coils are studied to minimize the respective coupling effect. With the proposed integration method, the extra coupling coefficients are either eliminated or decreased to a negligible level. A wireless charging system with the proposed integration method is built and the experimental results show that the system resonates at 85 kHz and delivers 3.09 kW with a dc–dc efficiency of 95.49% at an air gap of 150 mm. Furthermore, a comparison with the integration method into bipolar coil structures is presented and the results demonstrate that the system with the proposed integration method is more immune to front-to-rear and vertical misalignments. [ABSTRACT FROM AUTHOR]

A quasi-Z-source inverter (qZSI) could achieve buck/boost conversion as well as dc to ac inversion in a single-stage topology, which reduces the structure cost when compared to a traditional two-stage inverter. Specifically, the buck/boost conversion was accomplished via shoot-through state which took place across all phase legs of the inverter. In this paper, instead of using traditional dual-loop-based proportional integral (PI)-P controller, a type 2 based closed-loop voltage controller with novel dc-link voltage reference algorithm was proposed to fulfill the dc-link voltage tracking control of a single-phase qZSI regardless of any loading conditions, without the need of inner inductor current loop. A dc–ac boost inverter with similar circuit parameters as a qZSI was used to verify the flexibility of the proposed controller. The dynamic and transient performances of the proposed controller were investigated to evaluate its superiority against the aforementioned conventional controller. The integrated proposed controller and qZSI topology was then employed in static synchronous compensator application to perform reactive power compensation at the point of common coupling. The effectiveness of the proposed approach was verified through both simulation and experimental studies. [ABSTRACT FROM AUTHOR]