Search

In this article, a high-power-density off-line light-emitting diode (LED) driver is proposed. The proposed ac–dc driver is the novel integrated buck and boost converter (IBBC). Besides the high-power-density, the converter shows a high power factor (PF), and a low total harmonic distortion (THD). The IBBC is a two-stage driver that features just one controlled switch, which leads to high PF and low THD operation ensuring high efficiency, and size and cost reduction. Moreover, the switch current is minimized as it conducts the higher of the buck or boost converter, but not the addition of both as in other integrated converters. Moreover, for a further increase of the power-density, a magnetic integration is made by integrating the two inductors of both the buck and boost converters in one core. Thus, the proposed converter has been named as fully integrated buck and boost converter (FIBBC). In this paper, the IBBC is analyzed, and a design methodology is proposed. Also, this article presents a magnetic analysis of the novel FIBBC. In addition, a comparison between two prototypes is presented, one for the IBBC and another for the FIBBC, both of them supplying an LED luminaire of 46 V/ 0.575 A. The FIBBC shows a high PF equal to 0.994, very small THD of 10%, output current ripple of 6%, and efficiency of 92.62%, which represents a landmark on the efficiency of integrated converters. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) technology is useful for electric vehicle (EV) charging because of safe, flexible, and convenient features. In this paper, an integrated IPT system design employing variable inductor control is proposed to achieve a target constant current (CC) and constant voltage (CV) battery charging profile with misalignment tolerance. The system is implemented under a fixed switching frequency in both CC and CV modes. Soft switching of the primary inverter can be achieved over the entire charging process and allowed misalignment range without additional switches or dc–dc converters. Theoretical circuit analysis and the system design process are presented. A 3.3-kW prototype is implemented with a 210-mm air gap to demonstrate the validity of the proposed method. Experimental results show that the target CC and CV charging profile can be achieved by adjusting the variable inductor with up to 120 mm of lateral and 300 mm of vertical misalignment. The maximum efficiency of the proposed system is 96.1% at full output power and stays above 95% throughout CC operation. [ABSTRACT FROM AUTHOR]

This paper proposes a dual-coupled LCC-compen-sated inductive power transfer system with a compact magnetic coupler to improve misalignment performance. In the magnetic coupler, the main coils form the first coupling, and compensation inductors are integrated with the main coils to form a second coupling. In the design presented in this paper, the main coils are unipolar and the compensation inductors are in a Double D structure. The fundamental harmonics approximation method is used to analyze the circuit, and the couplings between the main coils and compensation inductors are considered to determine the net power flow. In misalignment cases, it is shown that the coupling between the compensation inductors, and the cross couplings between the compensation inductors and main coils, contribute to increasing the system power. A 3.5 kW prototype is designed and implemented to validate the proposed dual-coupled system. The primary coil size is \text450 mm\times \text450 mm, and the secondary coil size is \text300 mm\times \text300 mm. Experimental results show that the proposed dual-coupled system can significantly improve the misalignment performance, and retains at least 56.8% and 82.6% of the well-aligned power at 150 mm misalignment in the x- and y-directions, respectively. [ABSTRACT FROM PUBLISHER]

This paper introduces a non-isolated high step-up dc–dc converter with dual coupled inductors suitable for distributed generation applications. By implementing an input parallel connection, the proposed dc–dc structure inherits shared input current with low ripple, which also requires small capacitive filter at its input. Moreover, this topology can reach high voltage gain by using dual coupled inductors in series connection at the output stage. The proposed converter uses active clamp circuits with a shared clamp capacitor for the main switches. In addition to the active clamp circuit, the leakage energy is recycled to the output by using an integrated regenerative snubber. Indeed, these circuits allow soft-switching conditions, i.e., zero voltage switching and zero current switching for active and passive switching devices, respectively. The mentioned features along with a common ground connection of the input and output make the proposed topology a proper candidate for transformer-less grid-connected photovoltaic systems. The operating performance, analysis and mathematical derivations of the proposed dc–dc converter have been demonstrated in the paper. Moreover, the main features of the proposed converter have been verified through experimental results of a 1-kW laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a procedure for evaluating self-capacitances and parasitic capacitors between physically adjacent turns in multiconductor systems—with a special focus on single-layer air-core inductors. To this end, the paper proposes the use of standard cells, which correspond to a minimal and basic turn, layer, or macrolevel arrangement of a winding in reference to its patterns of stored electrostatic energy. A standard cell embraces mathematical rules derived by means of a curve fitting approach through a set of finite element analysis (FEA) simulations. Besides, it is applied in a matching routine wherein self- and stray capacitances are evaluated according to the relative position of each turn, layer, or macrolevel arrangement along the length of the winding. Finally, the analytical technique is validated by comparing frequency-domain results obtained from an implemented SPICE model and laboratory measurements. [ABSTRACT FROM PUBLISHER]

To support the development of high-frequency ac microgrids in terms of compact design, high-voltage gain and low total harmonic distortion (THD), a buck–boost dual-leg-integrated step-up inverter is proposed in this paper. The inverter is formed by integrating a buck–boost converter into a conventional single-phase full-bridge inverter by sharing the upper switch and the body diode of the lower switch in both bridge-legs. Consequently, the component count is significantly reduced over the step-up inverter counterparts. In addition, to address the drawbacks of hybrid modulation methods adopted by existing dual-leg-integrated inverters, such as double-variable control, and high THD of output voltage/current at high input voltage and heavy load conditions, unipolar frequency doubling sinusoidal pulse width modulation scheme is adopted in this inverter. As a result, the modulation ratio M becomes the only control variable to regulate the output voltage/current and the control is simplified. The THD of the proposed inverter output can remain low throughout the entire input voltage range and load power range. This paper presents the topology derivation procedure, operation principle, and steady-state characteristics of the proposed inverter. To validate the effectiveness of theory, experimental results of a 400 W hardware prototype, where the output voltage frequency is at 500 Hz, are reported. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure of nonisolated boost dc–dc converters based on voltage-lift technique is proposed. In comparison with conventional nonisolated boost dc–dc converters, the proposed converter generates higher voltage gain. In this paper, the relations between voltage and current of all elements in continuous conduction mode and discontinuous conduction mode are calculated as well as voltage gain in each mode. Then, the critical inductance and stress of switch current are extracted. Finally, the validity of given theories is examined by using the experimental results. [ABSTRACT FROM PUBLISHER]

A new modulated carrier control (MCC) method is proposed in this paper for a power factor correction (PFC) boost converter, which provides high power factor (PF) and low total harmonic distortion (THD) in wide input voltage and load range. The proposed MCC method employs a zero current duration (ZCD) demodulator that detects ZCD in each switching cycle to estimate current conduction duration of the boost inductor. Using the estimated signal of the ZCD demodulator, the proposed controller generates a compensated duty signal with a PFC converter to properly operate in continuous conduction mode (CCM) or discontinuous conduction mode (DCM). Unlike the conventional MCC PFC converter where the line current is distorted in DCM resulting in poor PF and high THD, the proposed MCC method can provide higher PFC performance regardless of CCM and DCM while maintaining the simple control loop of conventional MCC control method that does not require inner current loop and using relatively small inductance. In this paper, the operational principle of the proposed method has been discussed. To verify the proposed method, it has been tested on a 400-W PFC boost converter. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase power factor correction (PFC) rectifier to achieve high power factor, wide output voltage range, and ripple power decoupling without using electrolytic capacitors. It consists of two parts: PFC circuit and output voltage regulation circuit. The load side is involved in both parts, which is different from the regular two-stage conversion structure. The proposed rectifier can be directly applied to low voltage cases due to the wide output voltage range. And the decoupling capacitor voltage can be smaller than the peak grid voltage, which reduces the voltage stress. Besides, the low-frequency ripple power buffer is implemented without a dedicated power-buffering controller. This paper first introduces the circuit structure, operation principles, and control method. Then, the system design consideration is given. Finally, the effectiveness of the proposed topology is verified by the simulations and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, two resistive matching networks are proposed, which can maintain the resistive transferring property under different load conditions. The high-frequency converter based on the resistive network can adequately achieve the soft-switching characteristics within a large load variation range, which helps to reduce switching losses and improve system efficiency. At the same time, a detailed design method for planar spiral inductor is described. In addition, the quality factor characteristics of different winding structures are analyzed. A 20-MHz high-frequency dc/dc converter based on the T-type matching network and circular spiral inductor is designed in this paper. The experimental results verify the advantages of the proposed resistive matching network and spiral inductor. [ABSTRACT FROM AUTHOR]

An optimal dual-phase-shift control strategy of an isolated buck–boost converter is proposed in this paper. The theoretical analysis of dual-phase-shift control strategy is complemented, and the three-dimensional graphs of the output current versus two control variables are given. The optimal operating point is determined by the peak current of a clamped inductor and is shown as control trajectories in the three-dimensional graphs. Moreover, with the optimal dual-phase-shift control strategy, low current value, soft-switching operation, wide input voltage range regulation, whole load range regulation, and high-efficiency performance can be achieved. Furthermore, parameter design method deriving from the minimum peak current of the clamped inductor is given. At the end of this paper, a 1000 W-output prototype is fabricated to verify the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

A switched-capacitor-based dual-switch dc–dc converter with a high-boost voltage gain is proposed in this paper. The proposed converter can obtain a high-voltage gain with a small duty cycle, which decreases the voltage stress and the conduction loss on the power switches. This paper presents the key waveforms, the operating principles at the continuous conduction mode and the discontinuous conduction mode, and the parameter design. Moreover, a comparison between the proposed converter and other nonisolated converters has been completed. To verify the operating principle, a 200 W prototype is constructed with an input voltage of 25–50 V and an output voltage of 200 V. The simulation and experimental results are shown. [ABSTRACT FROM PUBLISHER]

This paper proposes a decentralized current-sharing control strategy to endow fast transient response to paralleled dc–dc converters systems, such as dc microgrids or distributed power systems. The proposed controller consist of two main control loops: an external voltage droop control for current-sharing proposes and an internal current loop. The external droop control loop is designed as a voltage loop with embedded virtual impedance, which avoids the use of a slow voltage loop and a separate extra virtual impedance loop that may limit the system bandwidth. The internal current loop, thanks to the external control loop simplification, plays a major role in the system bandwidth, so that an adaptive proportional-integral (PI) controller is proposed for this matter. In the paper, two different droop control methods have been modeling, designed, simulated, and tested: The conventional virtual-impedance-loop based V–I droop and the proposed embedded-virtual-impedance based I–V droop. In order to compare the dynamic response performances between two droop controllers, their state-space models have been developed and analyzed in this paper. The results show that the dynamic response of the I–V droop control is faster than that of the conventional V–I droop control. Furthermore, by analyzing the effects from I–V droop control parameters, the errors can be reduced faster by enlarging the proportional terms, but with no fluctuations, and then completely eliminated by restoring back to small proportional values. Meanwhile, there exists a tradeoff phenomenon between the fast dynamic response and good steady-state performance; thus, an adaptive PI controller is proposed to both improve dynamic response and guarantee good steady-state performance simultaneously. Experimental results are shown to verify the accuracy of the models and the effectiveness of the proposed control framework. [ABSTRACT FROM PUBLISHER]

This paper presents a phase-shifted dual-half-bridge converter, which achieves zero-voltage switching (ZVS) for the leading-leg switches and zero-current switching (ZCS) for the lagging-leg switches. The proposed converter contains two paralleled half-bridge inverters in the primary side. The rectifier stage is composed of six diodes connected with the form of full-bridge rectification. The ZVS condition is created by the output filter inductor and leakage inductor, while the ZCS condition is created by the blocking capacitors. A wide range of soft-switching operation can be achieved with small leakage inductors. Compared with the traditional phase-shifted full-bridge converter, the proposed converter can obtain a three-level output rectified voltage, and the power is transferred from the primary side to the secondary side during the whole period, which can significantly reduce the current ripple of the output filter inductor. In this paper, the operation principle and relevant analysis are presented. A laboratory prototype is built to verify the performance of the proposed converter. [ABSTRACT FROM PUBLISHER]

This paper proposes a new bidirectional resonant dc–dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc–dc converters, and meanwhile achieves high efficiency throughout the wide range of operation voltage. It is achieved by configuring a full-bridge mode and a half-bridge mode operation during each switching cycle. A fixed-frequency phase-shift control scheme is proposed and the normalized voltage gain can be always from 0.5 to 1, regardless of the load. The transformer root-mean-square (rms) currents in both the forward and reverse power flow directions have a small variation with respect to the voltage gain, which is beneficial to the conduction losses reduction throughout a wide voltage range. Moreover, the power devices are soft-switched for minimum switching losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology and analysis are verified with experimental results obtained from a 1-kW converter prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a comprehensive analytical LCL filter design method for three-phase two-level power factor correction rectifiers (PFCs). The high-frequency converter current ripple generates the high-frequency current harmonics that need to be attenuated with respect to the grid standards. Studying the high-frequency current of each element proposes a noniterative solution for designing an LCL filter. In this paper, the converter current ripple is thoroughly analyzed to generalize the current ripple behavior and find the maximum current ripple for sinusoidal pulse width modulation (PWM) and third-harmonic injection PWM. Consequently, the current ripple is used to accurately determine the required filter capacitance based on the maximum charge of the filter capacitor. To choose the grid-side inductance, two methods are investigated. First method uses the structure of the damping to express the grid-side filter inductance as a function of the converter current ripple. Reducing the power loss in the filter and optimizing the grid-side filter inductance is the main focus of the second method which is achieved by employing line impedance stabilization network (LISN). Accordingly, two LCL filters are designed for a 5 kW silicon-carbide-based three-phase PFC. Various experimental scenarios are performed to verify the filters attenuation and performance. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid nonisolated dc–dc commutation cell, which is generated by the integration between conventional commutation cell and ladder-type passive switched capacitor (SC) cell. From the resulted hybrid cell are derived three different dc–dc converters: a buck-type, a boost-type, and a buck–boost-type. The three structures are analyzed in this paper and are presented the topological stages, static gain characteristics in continuous conduction mode and discontinuous conduction mode, steady-state analysis. The analyses are generalized in relation to the number of switched-capacitor cells employed, which allows the increase of the rated gain of the converters by adding more SC cells. In addition, the proposed hybrid nonisolated dc–dc commutation divides naturally the voltage stress among the semiconductors and capacitors of the power stage. A 1-kW prototype was developed to verify the operation of the three proposed converters and their theoretical analysis. For the buck-type topology, designed with an input voltage of 600 V and output voltage of 450 V, a peak efficiency of 99.2% and efficiency at rated power of 99% were obtained. [ABSTRACT FROM PUBLISHER]

Sheppard–Taylor power factor correction (ST-PFC) rectifier could obtain a high power factor due to its capability of overcoming the control detuning issue. However, it needs a bulky electrolytic capacitor at the load side to buffer the double-frequency ripple power (DFRP), which reduces the reliability and power density significantly. This paper proposes a control method to divert the DFRP to the small energy transfer capacitor. Consequently, the bulky electrolytic capacitor is replaced with a small film capacitor. The proposed method is carried out by introducing the freewheel state (one switch is turned on and the other is turned off) into the control. So no extra hardware is added, which makes the proposed method cost-effective. A low electromagnetic interference emission is also achieved due to the continuous input–output currents. In addition, the proposed method can be extended to other topologies easily. This paper first gives the detailed analysis of the proposed control method, and then introduces the controller design. The selection of the passive components is also briefly discussed. Finally, the simulation and experimental results verify the effectiveness of the proposed control method. [ABSTRACT FROM AUTHOR]

These days, constant on-time current mode (COTCM) control scheme is widely used in the voltage regulator (VR) controllers because it has a higher light-load efficiency and a higher BW design capability while maintaining a simpler compensation requirement. One issue plaguing the COTCM control is its slow transient response which is caused by its fixed TON operation. During the heavy-load step-up transient, the duty cycle becomes saturated and the inductor current increment becomes limited by TON and the minimum off time (TOFF$\_$ MIN) ratio, which can create a large undershoot at load step up. On the other hand, in the load step-down case, if the load step down occurs at the beginning of TON, a large overshoot can be created at the output. To solve this issue, this paper presents a method designed to increase the TON at load step up and then very quickly, decrease at load step down in order to reduce the undershoot and overshoot at output or otherwise save the output capacitor. In this proposed method, the increase or decrease of T ON is proportional to the output change which eliminates the chance of any overcorrection or ring-back problem unlike the methods presented in prior forums. This feature enables the control to work seamlessly in a high-frequency load repetitive case in VR applications. Since this TON change occurs only in the transient period when duty cycle is saturated, it does not affect the small-signal property of the COT control. Moreover, the proposed methods are very much compatible with the state-of-the-art single and multiphase COT control structures. Simulation and test results in both single and multiphase operations are also presented in the paper to verify the proposed concept. [ABSTRACT FROM PUBLISHER]

This paper presents a design method for a resonant class-DE rectifier with a shunt inductance input network. The cass-DE resonant rectifier offers numerous advantages at high operating frequencies and high output voltages. For a high-voltage design, the limiting factor has been the absence of a design process incorporating shunt inductance for low-to-high impedance matching as well as nonlinear capacitance from semiconductor devices. To design a rectifier with a specific input impedance at the fundamental frequency of operation, designers have been relying on either parametric variation in iterative simulations that often takes a long time to complete, or simple equations without considering nonlinear capacitances that renders the analysis inaccurate at high frequencies. In this paper, we propose a design procedure that begins with universal design curves that are applicable regardless of the capacitance nonlinearity. This is followed by parameter selection and a convergence check to ensure the rectifier operates at the desired output voltage. Based on the outlined procedure, we design and experimentally verify a 27-MHz 350-V current-driven rectifier, a 25-MHz 500-V voltage-driven rectifier, and a 27.12-MHz 2-kV four-stage rectifier, all of which the resonant capacitor is nonlinear and the input impedance is resistive at the switching frequency. [ABSTRACT FROM PUBLISHER]

A novel soft-switching interleaved coupled-inductor boost converter is proposed in this paper. Only a single active soft-switching module is needed to simultaneously achieve the soft-switching property of the two switches in the interleaved coupled-inductor boost converter. The better efficiency is achieved with the less components and cost. The two main switches can achieve the ZVT turn-on and smaller-current turn-off simultaneously when the single active soft-switching module is active. Due to the coupling characteristic of the inductors, the voltages across the two inductors are changed at the same time; therefore, the equivalent circuit is equal to the parasitic capacitors of the two main switches in parallel to resonate with the auxiliary inductor. By coupling two input inductors, the volume and cost of the circuit can be reduced. The interleaved coupled-inductor topology can also reduce the input and output current ripples and share the input and output currents. The operating modes, analysis, and design of the proposed circuit have been discussed in this paper. Simulation and experiments are finally conducted to verify the validity of the proposed circuit. [ABSTRACT FROM PUBLISHER]

It is mandatory to keep the total harmonic distortion in the output of most inverters below the limits prescribed by different international standards. The harmonic distortions caused due to nonlinear loads may not get corrected by typical magnitude controller, like PID controller. Repetitive controller is more effective in such situations. Often, repetitive controller is used as add-on block to the conventional magnitude controller. Design of repetitive controller can be easily implemented on digital platform. Rapid change in phase and magnitude of inverter-filter's transfer function near corner frequency causes instability problems in repetitive controller. Various techniques have been proposed by researchers to overcome this problem. Most of the reported techniques rely on digital compensation. However, it is hard to find a digital compensator, which simultaneously meets the phase and gain requirements at moderate computational effort. Here, a new output voltage feedback scheme has been proposed, which simplifies the requirement of digital compensation. The proposed scheme requires an extra hardware but at negligible added cost. In spite of this extra hardware, the proposed circuit turns out to be more energy efficient in comparison to few popular schemes, reported in literature, where some resistance is introduced in the inverter's filter for better stability of controller. In addition to the proposed modification the paper presents a simplified explanation of the various factors affecting stability of repetitive controller. The paper also discusses a novel experimental method for verifying the efficacy of repetitive controller in suppressing distortion of any particular harmonic order. [ABSTRACT FROM PUBLISHER]

DC electric springs (DCES) are emerging technologies for the (i) regulation of mains voltage against the intermittent renewable generations and (ii) harmonic cancellation in dc microgrids. When conventional converter topologies (e.g., half-bridge or full-bridge converter) are adopted as DCES, the battery storage of the DCES has to process both the dc power and the ac harmonic power. The pulsating ac power can severely reduce the lifetime of the battery. To address this issue, a hybrid-DCES (H-DCES) is proposed in this paper to perform (i) and (ii) in a decoupled manner. With a modified topology and control method, the H-DCES can divert the ac current to the ground and retains the function of manipulating noncritical load for dc voltage regulation. The immediate benefits of this H-DCES are the reduction of storage capacity and a prolonged lifetime of the battery. Both the operating principle and the mathematical model of the proposed H-DCES are analyzed in this paper. A prototype of the H-DCES is practically tested in a 48-V dc grid. The experimental results show that the H-DCES can realize the decoupled operation of dc voltage regulation and harmonic cancellation. Simulation studies further demonstrate that the H-DCES requires less storage capacity than its counterparts. [ABSTRACT FROM AUTHOR]

This paper documents a new three-switch, isolated boost dc–dc converter. The major features of the proposed converter are as follows: 1) continuous input current; 2) reduced one active switch, one additional diode, and one additional capacitor; 3) unchanged primary and secondary voltage waveforms of the transformer when the duty cycle is changed; and 4) removal of the snubber circuit. This paper presents the operating principles, analysis, parameter design guidelines, and simulation results for the proposed converter. To verify the performance of the proposed converter, a 400 W prototype was constructed with a 40–60 V dc input. A PID controller was used to maintain the dc output voltage at 400 V. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

The subject of this paper falls under the development of power electronics for more electric aircraft systems. The study concerns the design of a converter whose function is to generate a 300-V dc bus from a standard 28-V dc avionic network. Various systems, such as motor drives, need to be connected to the 28-V dc network. Their design could be simplified significantly, and standardized, by introducing this intermediate 28–300-V stage. The step-up converter in the proposed configuration is integrated as a part of the system. The power specification is 10 kW, which leads to very high-current values on the 28-V side. The choice of the converter topology, therefore, needs to match this central constraint. The proposed converter uses six boost cells, associated to constitute a series–parallel architecture. This arrangement leads to significantly more optimal sizing for high step-up ratios than conventional boost-cell configurations. Cell interconnection is implemented by means of a monolithic InterCell transformer to reduce the weight of the magnetic part. This paper describes the topology, design, and construction of the lab prototype, as well as experimental results obtained during testing. [ABSTRACT FROM PUBLISHER]

In high-power applications, parallel operation is required to improve both efficiency and reliability. In an LLC converter, it is difficult to achieve parallel operation due to the gain sensitivity to component tolerance. This paper proposes a new structure of a common resonant capacitor for a multiphase LLC converter, which can achieve very good current-sharing performance with no additional components or control. To evaluate the current-sharing performance, a new first harmonic approximation (FHA) model is built in this paper to analyze the LLC converter with coupled resonant tanks. Both FHA analysis and powersim (PSIM) simulation results demonstrate the load-sharing improvement of the proposed common capacitor LLC resonant converter over the conventional two-phase LLC converter. The current-sharing performance from the FHA analysis and the PSIM simulation are compared, and the error of the FHA analysis is evaluated and explained. A 600 W two-phase LLC converter prototype based on the proposed method is also built to verify the feasibility. Excellent current-sharing performance (6% resonant current sharing error at a wide load range) has been achieved. [ABSTRACT FROM PUBLISHER]

In this paper, a new zero voltage zero current transition (ZVZCT) boost DC–DC converter using a coupled inductor is proposed. This topology provides the main switch ZVZCT for the turn-on and zero voltage switching (ZVS) for the turn-off. Moreover, the auxiliary switch turns on at zero current switching (ZCS) and turns off at ZVS. The main diode turns on with ZVT and turns off with ZCS, and other diodes also operate under soft-switching conditions. Besides, due to the coupling effect, the proposed converter improves efficiency additionally since resonant energy in the resonance tank could be transferred to the output, and the circulating current can be limited as well. The soft-switching can be realized in almost all the load rang. In this design, there always exist energy releasing circuits to conduct magnetic flux leakage currents, such that the surge currents are eliminated and switch current stress can be accordingly reduced. All the devices resonate in a unique direction within less than half of a resonance period, so power losses with respect to the resonance can be decreased. In this paper, the converter design and operation principles of the converter are given. It also has been verified by a 1-kW experimental prototype with switching frequency of 100 kHz, and the related experimental results are presented. [ABSTRACT FROM PUBLISHER]

This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter. [ABSTRACT FROM PUBLISHER]

Instead of bulky electrolytic capacitors, active power decoupling circuit can be introduced to a single-phase converter for diverting second harmonic ripple away from its dc source or load. One possible circuit consists of a half-bridge and two capacitors in series for forming a dc-split capacitor, instead of the usual single dc-link capacitor bank. Methods for regulating this power decoupler have earlier been developed, but almost always with equal capacitances assumed for forming the dc-split capacitor, even though it is not realistic in practice. The assumption should, hence, be evaluated more thoroughly, especially when it is shown in the paper that even a slight mismatch can render the power decoupling scheme ineffective and the IEEE 1547 standard to be breached. A more robust compensation scheme is, thus, needed for the dc-split capacitor circuit, as proposed and tested experimentally in the paper. [ABSTRACT FROM AUTHOR]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

Conventional single-phase power-factor-correction (PFC) rectifiers with active power decoupling capability typically require more than three active switches in their circuits. By exploring the concept of power-buffer cell, a new single-stage PFC rectifier with two active switches, one inductor and one small power-buffering capacitor is reported in this paper. The proposed converter can achieve high-power factor, wide output voltage range, and power decoupling function without using electrolytic capacitor. Additionally, an automatic power decoupling control scheme that is simple and easy to implement is proposed in this paper. The operating principle, control method, and design considerations of the proposed rectifier are also provided. A 100-W prototype with ac input voltage of 110 Vrms and a regulated dc output voltage ranging from 30 to 100 V has been successfully designed and practically tested. The experimental results show that with only a 15 μF power-buffering film capacitor, the proposed converter can achieve an input power factor of over 0.98, peak efficiency of 93.9%, and output voltage ripple of less than 3%, at 100-W output power. [ABSTRACT FROM PUBLISHER]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

This paper proposes a new methodology to control a three-phase boost power factor correction (PFC) using a single dc output voltage sensor. Typically, a PFC control technique requires measurement from five independent sensors, i.e., two input voltages, one output dc voltage, and two input phase currents. Elimination of four sensors in the control system of a PFC converter is theoretically feasible and implementable without compromising stability and power quality of the converter, as analyzed and presented in this paper. The proposed control technique uses the ripple information of the measured dc-link voltage, converter dynamics, and switching states at a preceding sample in order to estimate the present state of four other unknown state variables and, thus, establishes the control method. A 2.2-kW experimental prototype of a three-phase boost PFC is developed and tested to verify the accuracy and applicability of the proposed control logic at different line and load conditions. According to the experimental measurements, conversion efficiency more than 98%, total harmonic distortion as low as 4.3%, and an output voltage ripple of ±2% are achieved at 2.2-kW output power. [ABSTRACT FROM AUTHOR]

This article is the continuation of graph sets method (GSM) proposed in the companion paper Part I for deriving equations and analyzing multicoil wireless power transfer multicoil (MC) wireless power transfer (WPT) systems. After explaining GSM, categorizing WPT coils into three different types, and proposing some approximation techniques in Part I, this article, as the second part of this work, presents numerical simulations and experimental results for a three-coil MCWPT system similar to what is explained in Part I. The simulations are conducted in MATLAB/Simulink and ANSYS environments, and for the experimental model, three ferriteless cylindrical coils are built and compensated to behave as voltage driven, current driven, and passive coils, respectively, at the specific frequency of 200 kHz. After analyzing and comparing the simulation and experimental results, it is shown that GSM can be an effective and illustrative technique that facilitates comprehensive analysis of interactions amongst the coils and their characteristics, especially when WPT systems contain multiple coils. [ABSTRACT FROM AUTHOR]

Water treatment is one of the most important issues for all walks of life around the world. Different from the conventional water treatment technology, the advanced power electronic pulse technology has unique features and advantages for the modern water treatment. Unfortunately, there is no literature reported to describe them in a comprehensive and systematic way. To fill this gap, an overview of modern power electronic pulse generators (PPGs) for water treatment is presented. This article, for the first time, classifies the different types of PPGs from the viewpoint of pulse formation. Each of them is discussed, and the advantages and disadvantages are compared and summarized. Aside from that, this article presents the development and trend of the pulse generators suitable for the specified water treatment processes such as electrolysis, sterilization, and discharge degradation. Finally, a list of more than 100 relevant technical papers is also appended for a quick reference. [ABSTRACT FROM AUTHOR]

Renewable energy generations have been attracting sustained attentions in academic and industry. Current-fed-isolated-bidirectional dc/dc converters (CF-IBDCs) are widely adopted in low-voltage high-current applications such as solar photovoltaic fuel cell with energy storage. This paper gives an overview and a comprehensive comparative evaluation of CF-IBDCs. The active clamped, dual half-bridge, L-L type dual active bridge, resonant-type, naturally clamped, and other type topologies of CF-IBDCs are investigated, analyzed, and compared regarding their circuit topological structures, operation characteristics, modulation methods, and soft-switching technologies. In addition, component cost models and loss models of converters are deduced and presented. On this basis, quantitative and comprehensive performance comparison of seven typical CF-IBDC topologies selected from each type is conducted in terms of costs, losses, weight, volume, and power density for the given system specifications and design constraints. Finally, the application range of different CF-IBDCs and future trend are presented to encourage further development. [ABSTRACT FROM AUTHOR]

This paper proposes a very simple analog control for quasi-square-wave zero voltage switching (QSW-ZVS) and triangular current mode bidirectional converters. The proposed circuit controls the inductance current, thanks to the use of a variable-width hysteretic current mode control. The upper and lower bounds of the hysteretic band are clamped to ensure QSW-ZVS operation with a single current command and independently from power flow direction. This enables the control to achieve a seamless transition between source and sink modes. The advantages and disadvantages of the proposed analog control are analyzed and two different power converters are built to demonstrate the validity of this solution: a 50 W, 48 to 24 V bidirectional buck converter and a 100 W, 24 to 48 V bidirectional boost converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology combining reconfigurability and hybridization is presented. Reconfigurability allows the proposed converter to operate in three different operating modes, yielding a wide range of step-up conversion ratios. The combination of two charge-pump cells and an inductor allows to reduce the average inductor current if compared to a standard equivalent boost converter. A prototype with integrated MOS, drivers, and logic but external passives was built. Experimental results show that with $\mathbf {f_{s} }=\text{300}\,$ kHz, $\mathbf {V_{in} = \text{6}}\,$ V, and $\mathbf {I_o = \text{70}}\,$ mA, the converter can cover conversion ratios in the range from $\text {2.5}$ to $\text {10}$ , with a maximum output voltage equal to $\text {60}\,$ V. Peak efficiency is $\text {91}$ %. When the output current is increased to $\text {100}\,$ mA peak efficiency is $\text {92.8}$ %. [ABSTRACT FROM AUTHOR]

This paper investigates the influence of active zero vector pulsewidth modulation (AZPWM-1) and space vector pulsewidth modulation (SVPWM) on the design of passive common-mode (CM) attenuation methods to reduce CM current and shaft voltage in inverter-fed V/f-controlled induction motor drives. The passive CM attenuation methods examined here are the CM choke, the CM electromagnetic interference (EMI) filter, and the CM transformer. The attenuation requirement of AZPWM-1 and SVPWM is identified to design the passive CM choke and EMI filter. Based on the attenuation requirement, the design guidelines are revisited for SVPWM, and design rules are proposed for AZPWM-1. However, the CM transformer is designed based on the step change in magnitude of CM voltage of both the pulsewidth modulations (PWMs). The limitations in design, regarding switching frequency and component size for each case, are also established. It is shown that to have a similar attenuation in the considered two PWM cases, AZPWM-1 requires smaller passive components compared to SVPWM. The proposed design guidelines are substantiated with experimental results on a 1.1-kW induction motor drive. [ABSTRACT FROM AUTHOR]

In this paper, a family of new step-up series–parallel dual resonant switched-capacitor converters (SP-DRSCs) is proposed to extend the conversion ratio for high step-up applications. The converters feature a wide gain range, continuously adjustable, and enhanced light-load voltage regulation. All flying capacitors operate in resonance, eliminating high transient current spikes and charge sharing losses. Thus, zero-current-switching (ZCS) turn-on for all transistors and ZCS turn-off for all diodes are achieved. A comprehensive analysis of the operation principle, voltage-gain curves, stable regulation range, and voltage and current stress is given. An analytical method to quantify the passive component volume for the group of step-up dual resonance switched-capacitor converters is presented. Further design considerations to optimize the passive component volume of the proposed SP-DRSC and the effect of bulky bypass capacitors on the volume are discussed. [ABSTRACT FROM AUTHOR]

The power efficiency and weight of present point-of-load (POL) dc–dc converters for drone applications are often compromised because they suffer from large switching losses at continuous conduction mode for heavy loads and excessive hardware overheads at discontinuous conduction mode for light loads. This paper presents a boundary conduction mode (BCM) control scheme for POL converters embodying a single operation mode. This is achieved by means of a hysteresis voltage controller to turn on/off the output power stage when necessary. The proposed BCM control scheme achieves high power efficiency (≥91.2%) over a wide load range (5 mA–1 A) by means of fully soft switching. Specifically, a hysteretic current controller is proposed to realize ZCS, and an adaptive dead time controller is proposed to realize ZVS. Further, the proposed BCM control scheme requires a small output inductor (0.82 μH) by means of designing the customizable peak inductor current. To verify the proposed BCM control scheme, we realize a BCM-based POL converter that features an input voltage range of 5–16 V, output voltage range of 2.5–8 V, switching frequency of 1.5 MHz, peak power efficiency of 96.8%, and ≤35 mV output voltage undershoot/overshoot for 1-A load step. When being benchmarked against state-of-the-art counterparts, the proposed design features the lowest voltage undershoot/overshoot, the highest switching frequency, ∼5.7× smaller inductor, and ∼11% higher power efficiency at light loads. [ABSTRACT FROM AUTHOR]

This paper proposes a ripple injection method in a two-stage intermediate bus architecture to overcome the incremental negative-impedance effect in the intermediate bus converter (IBC) induced by the constant power load, which is essentially a tightly regulated point of load (PoL) converter. The proposed method uses the voltage ripple of the intermediate bus in the feedback path for the closed-loop PoL converter while operating the IBC in open loop. The small-signal model is derived and verified using SIMPLIS simulation. The voltage ripple is shown to carry the inductor current information of the PoL converter. Thus, the proposed scheme is expected to retain the superior line regulation of current mode control for the PoL converter even without sensing the inductor current. Load current feed forward can improve the transient response for the PoL converter. Moreover, the load current information is also used to generate the appropriate duty ratio for the IBC during transient recovery. A simple PI controller is used for the PoL converter, which reduces the design complexity using the proposed control scheme. A hardware prototype is made, and the superior performance using the proposed control scheme is experimentally verified. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

With the conventional secondary phase-shifted (PS) control, a semidual-active-bridge (S-DAB) dc–dc converter suffers from low efficiency at light load in buck mode due to hard switching and high tank current. In order to avoid this phenomenon and extend soft-switching range, a hybrid control including the primary pulsewidth modulation plus secondary phase-shifted (PWM+PS) is proposed in this paper. Under the proposed hybrid control, all steady-state operation modes with distinctive features are identified and analyzed. Based on the operation range, power characteristics and switching behaviors in each mode, a minimum peak current control route is developed, which can enable the converter to work with low tank current and soft switching over the whole load range. A lab-scale S-DAB converter is implemented to validate the theoretical analysis, and experimental results reveal that the higher efficiency can be achieved using the proposed control route. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency three-level (TL) dc–dc converter with reduced circulating current and rectifier voltage stress by using coupled inductor in the rectifier circuit. Because of decreased circulating current, the conduction loss in the primary circuit is reduced. In addition, since the rectifier diodes with low forward voltage drop can be employed due to the small voltage stress, the conduction loss of rectifier diodes can be reduced. Therefore, the efficiency can be increased due to the reduction of the conduction losses in the primary circuit and rectifier diodes. The characteristics of the proposed converter are analyzed and compared with other TL converters. The validity of the proposed converter is verified by the experimental results of the prototype with 540–600 VDC input and 750 W (48 V/15.625 A) output. [ABSTRACT FROM AUTHOR]

This paper presents a pulsed power modulator with a new structure that utilizes the reverse recovery characteristics of diodes to achieve an effective pull-down circuit configuration. The proposed configuration for active pull-down applicable to negative pulsed power applications with a high-voltage direct switching method is implemented by adding a diode to the pulse discharging path of the modulator, instead of using a pull-down resistor. The diode is forward-biased while an output pulse voltage is applied to the load. When the pulse voltage applied to the load is removed, the residual energy in the load is quickly discharged through the reverse recovery path of the diode so that the pull-down function of the pulsed power supply system is efficiently performed. The operating principle of the proposed system is described, and each operating mode is analyzed in detail. In addition, the feasibility of the proposed system configuration is examined through various simulation results. Finally, it is proven that the proposed system can be used effectively in pulsed power application fields through a practical experiment in plasma source ion implantation applications. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of modular dc–dc converter has been proposed for medium voltage dc (MVdc) integration of high-penetration distributed PV. The proposed topology is featured with input-independent and output-series connected configuration and intermodule power balancing units (PBUs). A high voltage gain could be achieved with series-connected submodules (SMs), while each SM's input port is connected with PV array to realize the independent maximum power point tracking (MPPT) control function. PBUs with bidirectional power conversion ability are installed between adjacent SMs for the elimination of intermodule power mismatch. The operation principles of the proposed converter have been explained in detail along with the corresponding control strategies. The design principles of major passive components have been investigated on the basis of boundary operation conditions, while a quantitative analysis of steady-state power losses has been performed. Moreover, a comparative study is conducted from the aspects of operation range, topology complexity, component stress, and power efficiency. The theoretical results have been validated by both simulations and down-scaled experiments. [ABSTRACT FROM AUTHOR]

DC-to-DC power supplies are critical components for processors in high performance computing and datacenter servers. Conversion from an intermediate bus voltage (e.g., 12 or 48 V) to the core voltage (∼0.9 V) of processors must be efficient, compact, and cost effective. This paper proposes two versions of active-clamp forward converter (ACFC) power blocks to supply core voltage from either 12 or 48 V intermediate bus voltage. The ACFC power block can be individually tested prior to assembly and vertically soldered onto the motherboard to fit in a standard 1U server. A low loss, compact planar transformer is designed into the ACFC power block printed circuit board (PCB). A custom, standing slab inductor not only provides high inductance and high saturation current but also helps to mechanically support the power block. A one-piece copper winding connects the transformer to the inductor, thereby reducing the dc loss in the current path. Thorough analysis is performed to model the conversion loss of the proposed power block. Experimental results show a peak efficiency of 90.4% (12 V input) and 89.5% (48 V input) with 0.9-V output. [ABSTRACT FROM AUTHOR]

This paper introduces the high-frequency link concept into the modular multilevel converter (MMC) topology, which can totally reduce the individual dc-link capacitors at the high-voltage side. The proposed converter, called isolated MMC, has basic triple ports of medium-voltage ac, medium-voltage dc, and low-voltage dc. Thus, it is especially suitable for hybrid dc and ac applications in power generation and transmission, such as solid-state transformer. The fundamental principle and applied control scheme of phase-shift pulsewidth modulation are presented in detail. The design of the voltage clamping circuit and analysis of duty loss are carried out. The experimental results are given to illustrate the efficient operation characteristics. [ABSTRACT FROM AUTHOR]

The use of three-dimensional (3D) thermal simulations of magnetic components for power converters is limited to validation of final designs due to time consumption. A two-step homogenization is proposed to simplify them, while keeping good accuracy. The required equations and some guidelines are described in this paper. It can be applied to solid round wire, litz wire, or foil wound magnetic components. Considerations to extend its use to transformers, including the use of interleaving techniques and insulating tape, are explained. This method can reduce the computation time of 3-D simulations (seven times faster than usual simulations) while the convergence is assured even for complex structures or cases with litz wire. Finally, the method is experimentally validated with DC and AC excitation. [ABSTRACT FROM AUTHOR]