Search

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper presents a novel six-pulse low-frequency (LF) fluctuating high-voltage dc-bus-based power system architecture for fuel cell vehicles (FCVs) application. A novel hybrid modulation scheme consisting of six-pulse modulation at LF scale and modified secondary modulation and 33% pulse width modulation at high-frequency (HF) scale is proposed. Three-phase ac waveforms for the propulsion system of FCVs are generated from LF fluctuating high-voltage dc bus. The proposed modulation technique significantly reduces the switching losses of the bidirectional dual-stage inverter: 1) soft-switching of both sides of the front-end current-fed full-bridge converter is realized; and 2) at any moment, only one leg of back-end three-phase inverter is switched at HF, while the other two legs are kept in on or off states. This tremendously reduces the bidirectional inverter's switching losses and improves the system efficiency. The LF fluctuating high-voltage dc bus allows the elimination of large electrolytic dc-link capacitor, which contributes to a more reliable and compact design. This paper presents the operation, analysis, and design of a bidirectional inverter implementing the proposed hybrid modulation technique. Simulation results obtained from power electronics simulation software PSIM and experimental results from the lab prototype clearly validate the effectiveness of the proposed modulation technique. [ABSTRACT FROM PUBLISHER]

This paper presents a voltage multiplier topology that is a hybrid between a Cockcroft–Walton multiplier and a Dickson charge pump. The Cockcroft–Walton structure exhibits significant output voltage drop under load as the number of multiplier stage increases. This is because all coupling capacitors are connected in series. Dickson charge pump mitigates this issue by connecting all capacitors in parallel. But this solution comes at the expense of large capacitor voltage stress at the last multiplier stage. The proposed hybrid structure arranges some capacitors in parallel and others in series, thereby achieving low output voltage drop and low capacitor voltage stress at the same time. We develop a model that predicts hybrid multiplier's performance and validates it experimentally. We also demonstrate a 60–2.25 kV dc–dc converter based on a 16-stage hybrid voltage multiplier which achieves a voltage gain of 12.8 while keeping the highest capacitor voltage stress to 660 V. [ABSTRACT FROM AUTHOR]

The Cuk dual resonance core (DRC) realizes overlapped dual resonance to regulate its output voltage. However, the DRC configuration was only applied to the Fibonacci switched-capacitor converter (SCC), series–parallel SCC, and voltage doubler. In this paper, the Cuk DRC is modified and then is extended to the Dickson SCC to form a multi-resonance-core-based (MRC) Dickson resonant switched-capacitor converter. All charging and discharging loops achieve soft charging, and so the inherent capacitor charge sharing loss and the high current transient spikes are eliminated. The modular configuration makes the MRC Dickson easy to be extended to a higher voltage level. The on-time fixed frequency modulation is adopted, all transistors being turned on with zero-current-switching (ZCS) operation and all diodes being turned off with ZCS operation. Most importantly, the conversion ratio of the MRC Dickson can be regulated continuously, widely, and efficiently even at light load condition, which is a huge advantage over the traditional Dickson SCC with limited control headroom. A comprehensive analysis of the operation principle, voltage-gain curve, component stress analysis, and output characteristic is provided. The converter operation principle and regulation capability were verified by both simulation and experiment. [ABSTRACT FROM AUTHOR]

The low-frequency fluctuation over the capacitor voltages seriously limits the development of medium-voltage variable-speed drives with a modular multilevel converter (MMC). Therefore, this paper presents an effective strategy of the low-speed and start-up operation for an MMC-based motor drive. The proposed strategy properly coordinates the improved injection and the reduced average capacitor voltage with high applicability. The specific interactions between the control parameters and the system metrics are analyzed to give the detailed steps of the parameters designing. Hence, based on the derivations, the proposed method enables the low-frequency operation under the nominal load torque with decreased injected components and reduced peak capacitor voltages. What is more, two start-up strategies that, respectively, aim at different objectives for the coordinated strategy are proposed, indicating satisfying control performances for the practical applications. The injected common-mode voltage and circulating current in the proposed method are designed to have a great reduction. Thus, the unfavorable risks for the motor are evidently decreased for better stability. The reduced peak current also lessens the high stress on switching devices with desirable reliability. The simulation and experiment results of an MMC-based motor drive prototype prove the effectiveness and superiority of the proposed method. [ABSTRACT FROM AUTHOR]

This paper proposes a new family of multilevel inverter topology that is able to generate seven voltage levels by utilizing one or two floating capacitors and 10 power switches. This novel boost switched-capacitor seven-level inverter possesses voltage boosting capability with an achievable maximum voltage level 1.5 times the input direct current (dc) voltage. The generation of higher output voltage does not incur high-voltage stress on any power switch in this topology, as the peak inverse voltages of all power switches do not exceed the input source voltage. In addition, capacitor voltage balancing is not essential since the floating capacitors are effectively balanced during the charging and discharging processes. Furthermore, the proposed topology eliminates the need for multiple isolated dc sources, and a single dc source is sufficient in both its single-phase and three-phase topologies. The operating principle and steady-state analysis of the proposed topology are elaborated. Experimental results from a single-phase prototype are then presented to verify the validity of the proposed topology. [ABSTRACT FROM AUTHOR]

Active pulsating power buffering (PPB) is an effective technique to reduce the energy storage requirement of a single-phase power-factor-correction (PFC) rectifier. Existing single-phase solutions with active PPB, however, generally suffer from high voltage stresses, leading to increased power losses as well as the need for high-voltage-rating semiconductor switches. Previous works have been focusing on two-level switching converter configurations, and thus have failed to address the high-voltage-stress problem. In this paper, a single-phase three-level flying-capacitor PFC rectifier with PPB-embedded switching is proposed. The flying capacitor not only clamps the voltage stresses of all power devices but also functions as a PPB capacitor. The operating principles, control methods, and design guidelines are detailed and the feasibility of the proposed converter is verified through a 48-W (48-V/1-A) hardware prototype. The proposed rectifier is shown to achieve nearly 50% reduction of the voltage stresses, 72% reduction of the buffering capacitor's volume, and 23.8% reduction of the magnetic core size, as compared to a state-of-the-art two-level solution recently proposed. This new approach of formulating single-phase PFC rectifiers with active PPB could dramatically boost the system's efficiency and power density whilst reducing cost. [ABSTRACT FROM AUTHOR]

A novel high step-down dc–dc converter with voltage demultiplier cell is proposed in this paper, which is widely used in the high step-down applications such as electric vehicle and digital circuits. The combination of switched-capacitor and coupled-inductor is employed to build extended voltage demultiplier in the proposed converter, which makes a quite higher voltage conversion ratio than that of the existing counterparts. Thus, the proposed converter can achieve extremely low output voltage with an appropriate duty ratio, and the extreme duty cycle is avoided. Accordingly, voltage stress on power switches is greatly reduced. Then, mosfets with low conduction resistance could be utilized to reduce conduction loss. Importantly, zero-voltage switching could be achieved for the main switch, which promotes the conversion efficiency further. In addition, the coupled inductor operates not only as a filter inductor, but also as a transformer when the main switch is in the off state, which reduces the volume of the magnetic core and improves the power density of the converter. The operation principle, performance analysis, design considerations of the proposed converter and performance comparison with recent counterparts are discussed in detail, and finally, an experimental prototype is built to verify the theoretical analysis and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

In high gain voltage conversion applications, the low-side switches usually suffer large current stress, resulting in dominate switching loss. In this paper, a general soft-switching method based on an advanced interleaved high-step-up converter, which features excellent performance but works in hard-switching, is presented to combat this issue by using a plug-play resonant circuit. Under this soft-switching method, the main switches reach zero-voltage switching (ZVS) turn-on and ZVS turn-off, and the soft-switching condition is derived. Meanwhile, the added auxiliary switches could be turned off under ZVS condition and turned on under zero-current switching condition as well. More importantly, due to its location out of the energy transferring path, the auxiliary circuit will never lead gain lost to the converter and maintain its other existing merits, such as current auto-balancing and diode inverse-recovery well. A 1-kW prototype is built and tested to verify the significant efficiency improvement and merits maintenance for the proposed converter considering active resonant soft switching. [ABSTRACT FROM AUTHOR]

This paper presents a digital control technique to achieve valley switching in a bidirectional flyback converter used to drive a dielectric electroactive polymer-based capacitive incremental actuator. This paper also provides the design of a low input voltage (24 V) and variable high output voltage (0–2.5 kV) bidirectional dc–dc flyback converter for driving a capacitive incremental actuator. The incremental actuator consists of three electrically isolated mechanically connected capacitive actuators. It requires three high-voltage (HV) (2–2.5 kV) bidirectional dc–dc converters to accomplish the incremental motion by charging and discharging the capacitive actuators. The bidirectional flyback converter employs a digital controller to improve the efficiency and charge/discharge speed using the valley switching technique during both charge and discharge processes, without the need to sense signals on the output HV side. Experimental results verifying the bidirectional operation of a HV flyback converter are presented using a 3-kV polypropylene-film capacitor as the load. The energy-loss distributions of the converter are presented when 4- and 4.5-kV HV mosfets are used on HV side. The flyback prototype with a 4 kV mosfet demonstrated 89% charge energy efficiency to charge the capacitive load from 0 V to 2.5 kV, and 84% discharge energy efficiency to discharge it from 2.5 kV to 0 V. [ABSTRACT FROM AUTHOR]

This paper proposes a new interleaved high step-up converter with coupled inductors. Interleaving configuration is employed at the input side to reduce the input current ripple and increase the power level. The series structure at the output side helps achieve a very high step-up voltage gain. Also, the proposed converter has very low switch voltage stress; thus, switching loss can be reduced and low-voltage-rating mosfets with small on resistance are allowed to lower the conduction loss. Due to the passive clamp performance, the leakage energy of the coupled inductors can be recycled and large voltage spikes across the switches are alleviated. Furthermore, with the aid of the leakage inductances, zero-current switching of the active switches can be achieved and the reverse recovery problem of the diodes is alleviated. The operating principles, performance analysis, and design considerations of the proposed converter are discussed. A prototype with 20-V input and 400-V output is built, and experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

Impedance-source inverters using coupled inductors have been investigated as alternatives for providing high step-up voltages. However, leakage inductances of the coupled inductors have commonly led to lower overall effectiveness, in addition to generating high dc-link voltage spikes. The latter raises voltage stresses of switches, which in turn, may reduce the power levels of the inverters. A high step-up Y-source inverter has therefore been proposed in this paper to provide a high boost with a smooth dc-link voltage ensured by proper recycling of the leakage energy. These features have been verified by comparing simulation and experimental results of an existing Y-source and the proposed inverters. Factors compared are their respective boost ratios, voltage stresses, current stresses, and dc-link voltage spikes. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

This paper explores the use of the flying-capacitor multilevel (FCML) topology in high step-up conversion. Compared to the conventional two-level boost converter, the FCML topology utilizes high energy density capacitors to facilitate inductors with storing and transferring energy during the conversion process, which brings features, such as lower voltage stress on the switches, reduced voltage stress on the inductor, and high effective switching frequency at the switching node. As a result, the total volume of the passive components in the converter is greatly reduced while maintaining high efficiency at high voltage gain. To demonstrate the potential high power density and high efficiency, a hardware prototype that converts 100 V to 1 kV with 820-W maximum output power is built. Such specifications require careful optimizations in many aspects of the converter to ensure a high power density and efficiency design. The implemented solutions and associate design process are presented in detail, with comparison with other state-of-the-art solutions. The hardware prototype has successfully demonstrated a peak efficiency of 94.1%, and 329 W/in $^3$ (20 W/cm $^3$) overall power density. [ABSTRACT FROM AUTHOR]

This paper proposes an indirect input-series output-parallel (I2SOP) dc–dc full-bridge converter system based on asymmetric pulsewidth modulation (APWM) control strategy for high input voltage applications. When a short-circuit fault occurs in a high input voltage dc bus, the proposed I2SOP system can disconnect from the dc bus effectively and avoid the input filter capacitors of constituent modules discharge compared with the traditional ISOP system, facilitating fault handling and protecting the input filter capacitors. Moreover, with the proposed I2SOP structure, it is easy to achieve redundancy design when one or a few constituent modules fail. The APWM control strategy is introduced to the I2SOP system rather than the classical phase-shifted control strategy for the basic full-bridge module to reduce the voltage stress of power switch and the filter requirement. The characteristics of input voltage sharing and output current sharing of the I2SOP system are also analyzed. A three-module I2SOP system prototype was built, and the experimental results verify the correctness and effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents three nonisolated high voltage gain dc–dc converters with ripple-free input current. The proposed converters combine coupled inductors and voltage-doubler structure (VDS) to achieve high step-up of input voltage. An active clamp circuit is used to suppress voltage spike of the switch caused by of the leakage inductor of the coupled inductor. VDS is placed in the secondary winding of the coupled inductor that clamps the diodes voltage stress. Working principle and design methodology of the proposed converters are presented in detail. Experimental results for a 300 W laboratory prototype, 48 V input voltage, and regulated output voltage of 400 V, are shown to validate the operation of proposed converters. [ABSTRACT FROM AUTHOR]

The ultra-high voltage gain dc–dc converters are extremely required because of the low voltage level of many nonpolluting power resources. This paper proposes an ultra-high voltage gain converter based on an interleave technique and using three-winding coupled inductor and voltage multiplier cell. The interleave technique is useful for reducing the size of the filter components. In the proposed converter, high voltage gain is achieved without extreme duty cycle of solid-state switches. The voltage stress across the semiconductor devices can be reduced by increasing the turn ratio of the secondary of the coupled inductors. In addition, because of the implementation of the interleave structure, peak-to-peak variation of the main input current and switching losses are substantially reduced. The steady-state principles of the proposed converter in continuous conduction mode operation are given. Also, design equations are presented. Validity and performance of the proposed converter are surveyed by simulation and experimental results of a 120 W prototype. [ABSTRACT FROM AUTHOR]

The five-level active neutral-point-clamped (5L-ANPC) converter is becoming an attractive topology of multilevel converter family. A novel SVPWM algorithm based on line voltage coordinate was studied in this paper to overcome shortcomings of the traditional algorithm. Through coordinate transformation, steps of determining the basic vectors and the solution about the basic vector corresponding action time are simplified. Combining with the characteristics of 5L-ANPC converter and the new control algorithm, a method of controlling the voltage balancing of dc-link capacitors and floating-capacitors is proposed. According to the voltage of dc-link capacitors, the suitable switching sequence which can balance the voltage of dc-link capacitors is chosen. The high common-mode voltage will affect the service life of motor and reduce the reliability of the system especially in high-voltage converter. The common-mode voltage is also reduced by choosing the right switching state in this paper. The validity of the proposed method was proved by the experimental results. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become increasingly interesting in dc-dc applications, as there is a growing demand for dc-dc converters in high-voltage applications. Power electronics transformers can be used for high step-down ratio dc-dc power conversion, with high power rating and efficiency achieved. However, this arrangement requires a large number of high isolation voltage transformers and a complicated balancing control scheme. To provide a simple solution with inherent voltage balancing, this paper presents a new resonant MMC topology for dc-dc conversion. The proposed converter achieves high-voltage step-down ratio depending on the number of submodules. The converter also exhibits simplicity and scalability with no necessary requirement of high-voltage isolation transformers. By using phase-shift control, a much higher converter operating frequency is achieved compared to the switching frequency. Resonant conversion is achieved between the series inductor and submodule capacitors. The operation principle and theoretical analysis are presented in this paper, which have been verified by experimental results based on a bench-scale prototype. [ABSTRACT FROM AUTHOR]

A capacitor voltage balancing method for a modular multilevel dc (MMDC) converter is proposed. The MMDC inherits the desirable features of both a modular multilevel converter (MMC) and a dual active bridge, namely high voltage capability, fault tolerance, zero-voltage switching-on of all the power devices, and a wide operating range. These features are ideal for a dc transformer in any dc distribution system. One key MMDC control issue is balancing of submodule capacitor voltages. Conventional MMC balancing techniques cannot be used as arm currents of an MMDC change direction within each switching cycle. This paper establishes that the average capacitor voltage of each arm is self-balanced and proposes a method to balance voltages within an arm by assigning the gate signals with higher charge difference to the submodules with lower voltages and vice versa. Charge difference is obtained by the voltage difference, hence only the SM capacitor voltages are required for balancing control. Different from the existed methods, the proposed technique is not limited by voltage gain or load conditions. Simulation and experimental results show that capacitor voltages are balanced under different voltage gains, different output power, and also when the MMDC starts up, hence ensuring the stable MMDC operation. [ABSTRACT FROM PUBLISHER]

The modular multilevel converter (MMC) is attractive for medium- or high-power applications because of the advantages of its high modularity, availability, and high power quality. Reliability is one of the most important challenges for the MMC consisting of a large number of power electronic devices. The diode open-circuit fault in the submodule (SM) is an important issue for the MMC, which would affect the performance of the MMC and disrupt the operation of the MMC. This paper analyzes the impact of diode open-circuit failures in the SMs on the performance of the MMC and proposes a protection scheme for the MMC under diode open-circuit faults. The proposed protection scheme not only can effectively eliminate the possible caused high voltage due to the diode open-circuit fault but also can quickly detect the faulty SMs, which effectively avoids the destruction and protects the MMC. The proposed protection scheme is verified with a downscale MMC prototype in the laboratory. The results confirm the effectiveness of the proposed protection scheme for the MMC under diode open-circuit faults. [ABSTRACT FROM PUBLISHER]

This paper presents a dc–dc boost converter topology for low input and high output voltage applications, such as photovoltaic systems, fuel cell systems, high-intensity discharge lamp, and electric vehicles. The suggested configuration consists of a three-winding coupled-inductor, a single switch and two hybrid voltage multiplier cells. Furthermore, two independent hybrid voltage multiplier cells are in parallel when the single switch S is turned on, and they are in series when the switch S is turned off. So, the advantages of the proposed converter structure are summarized as follows: 1) A coupled inductor with three windings is introduced in the presented converter structure. The two secondary windings of the coupled inductor are, respectively, used to form a hybrid multiplier cell on the one hand, on the other hand, it increases the control freedom of the voltage gain, enhances the utility rate of magnetic core and power density, and reduces the stress of power components to provide a stable constant dc output voltage. 2) The two hybrid multiplier cells can absorb synchronously the energy of stray inductance, which not only reduces the current stress of corresponding diodes, but also greatly alleviates the spike voltage of the main switch, which improves the efficiency. 3) The two hybrid multiplier cells are connected in series to supply power energy for the load, so the voltage gain is extended greatly due to this particular structure. Thus, low-voltage low-conduction-loss devices can be selected and the reverse-recovery currents within the diodes are inhibited. The operating principles and the steady state analyses of the proposed converter are discussed in detail. Finally, a test prototype has been implemented in the laboratory, and the simulated and experimental results show satisfactory agreement with the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper deals with a new family of high boost voltage inverters that improve upon the conventional trans-Z-source and trans-quasi-Z-source inverters. The improved trans-Z-source inverter provides continuous input current and a higher boost voltage inversion capability. In addition, the improved inverter can suppress resonant current at startup, which might destroy the device. In comparison to the conventional trans-Z-source/-trans-quasi-Z-source inverters, for the same transformer turn ratio and input and output voltages, the improved inverter has a higher modulation index with reduced voltage stress on the dc link, lower current stress flow on the transformer windings and diode, and lower input current ripple. In order to produce the same input and output voltage with the same modulation index, the improved inverter uses a lower transformer turn ratio compared to the conventional inverters. Thus, the size and weight of the transformer in the improved inverter can be reduced. This paper presents the operating principles, analysis and simulation results, and compares them with those of the conventional trans-Z-source/-quasi-Z-source inverters. To verify the performance of the improved converter, a laboratory prototype was constructed based on a TMS320F2812 digital signal processor with 100 V dc input and 115 Vrms output voltage. [ABSTRACT FROM AUTHOR]

In the integrated reconfigurable converter (IRC) topology for high-voltage series-connected battery module systems, the converter can be reconfigured into a range of operating modes: “feeding a load” mode, “battery modules balancing” mode, “regenerative” mode, “charging” mode, and “backup” mode. In most battery applications, a battery-balancing system operates while another converter is used as a controllable power interface between the battery system and a load. However, during the conventional IRC operation, the “battery modules balancing” and “feeding a load” modes cannot be operated simultaneously. In this paper, a new balancing scheme is proposed that allows balancing the battery modules while they are powering the load. The proposed balancing strategy is able to distribute different amount of load between the battery modules based on their state of charge (SOC). When the load is disconnected, the battery modules can be still balanced using the conventional “battery modules balancing” mode. A scaled down prototype of the IRC is implemented with three series-connected battery modules. Experimental results are provided to verify the viability of the proposed balancing method. [ABSTRACT FROM AUTHOR]

This paper proposes a controlled transition full-bridge (CTFB) hybrid multilevel converter (HMC) for medium and high voltage applications. It employs a full-bridge cell chain-link (FB-CL) between the two legs in each phase to generate multilevel bipolar output voltage. The CTFB-HMC has twice dc voltage utilization or power density of conventional converters due to the bipolar capability of its full-bridge configuration. Hence, for the same power rating and same voltage level number, its total cells per phase are quarter that in modular multilevel converter (MMC), which reduces the hardware installation volume. Also, in the proposed converter, the total device number in the conduction paths is the same as in the half-bridge MMC, leading to low conduction losses. The FB-CL current of the CTFB converter has no dc component, which offers the potential to enhance the transient response. Comparative studies between the CTFB and other multilevel topologies are carried out to clarify its main features. The modulation strategies and parameter sizing of the proposed converter are investigated using a generic case. Simulation and experimental results are used to verify the effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]

High-voltage-gain and wide-input-range dc–dc converters are widely used in various electronics and industrial products such as portable devices, telecommunication, automotive, and aerospace systems. The two-stage converter is a widely adopted architecture for such applications, and it is proven to have a higher efficiency as compared with that of the single-stage converter. This paper presents a modular-cell-based morphing switched-capacitor (SC) converter for application as a front-end converter of the two-stage converter. The conversion ratio of this converter is flexible and variable and can be freely extended by increasing more SC modules. The varying conversion ratio is achieved through the morphing of the converter's structure corresponding to the amplitude of the input voltage. This converter is light and compact, and is highly efficient over a very wide range of input voltage and load conditions. Experimental work on a 25-W, 6–30-V input, 3.5–8.5-V output prototype, is performed. For a single SC module, the efficiency over the entire input voltage range is higher than 98%. Applied into the two-stage converter, the overall efficiency achievable over the entire operating range is 80% including the driver's loss. [ABSTRACT FROM AUTHOR]

In this paper, a three-phase multilevel power factor correction rectifier using the hybrid switched-capacitor concept is proposed. The converter is suitable for high-voltage-gain applications from conventional three-phase low-voltage sources. The three-level voltage operation reduces the weight and bulk of the magnetic devices. The main advantages of the proposed converter are low number of active switches, high voltage gain, sinusoidal currents, low voltage stress across all components, and simple control. Both steady-state and dynamic analyses are investigated. Experimental results for a 7500-W/220-V-to-1600-V laboratory prototype with maximum efficiency of 97.78% are presented and discussed. [ABSTRACT FROM AUTHOR]

An advanced hybrid LLC series resonant converter with integrated flying-capacitor cell is proposed in this paper to enable the high step-down conversion in the high input voltage applications. The inherent flying-capacitor branch in the primary side can effectively halve the primary switch voltage stress compared with the half-bridge LLC converters. And the input voltage can be shared equally and automatically between the two series half-bridge modules without additional balance circuit or control strategies due to the built-in flying-capacitor cell. Moreover, the inherent soft switching performance during wide load range that exists in the LLC converters is still kept to reduce the switching losses, which ensures the high efficiency. Besides, the proposed converter can be extended to further decrease the switch voltage stress by employing stacked connection. Finally, a 500 ∼ 640 V-input 48 V-output 1 kW prototype is built and tested to verify the effectiveness of the proposed converter. The results prove that the proposed converter is an excellent candidate for the high input voltage and high step-down dc/dc conversion systems. [ABSTRACT FROM PUBLISHER]

Featuring high efficiency, low harmonic distortion, high modularity and scalability, the modular multilevel converter (MMC) is particularly suitable for high voltage direct current transmission applications. As an advanced control strategy, model predictive control (MPC) has the advantage of direct modeling and fast dynamic response. It can simultaneously control multiple variables through an appropriate cost function. The conventional MPC can achieve an optimal control objective by evaluating all the candidate switching states for the MMC; however, with increasing number of submodules, there is an increasing number of candidate switching states that place an enormous burden on the control. In this paper, a grouping-sorting-optimized MPC (GSOMPC) strategy is proposed for the MMC with the number of submodules for each arm increases to hundreds. It divides all submodules of each arm into M groups, with each containing X submodules. By the implementation of the first level and second level optimized MPC between groups and submodules, respectively, the computational load of each phase decreases from C2N^N to $2X + M + 3(N = M \times X)$. In addition, to reduce the strict requirements of control hardware for sorting and calculation, the proposed strategy is able to simultaneously control the submodule voltage, ac current, circulating current, and switching frequency. Applied to a 2.7-kV/60-kW MMC back-to-back dynamic test system, experimental results verify the feasibility and effectiveness of the proposed GSOMPC strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a soft-switched single switch isolated converter. The proposed converter is able to offer low cost and high power density in step-up application due to the following features: zero-current switching (ZCS) turn-on and zero-voltage switching (ZVS) turn-off of switch and ZCS turn-off of diodes regardless of voltage and load variation; low rated lossless snubber; reduced transformer volume compared to flyback-based converters due to low magnetizing current. Experimental results on a 100 kHz, 250 W prototype are provided to validate the proposed concept. [ABSTRACT FROM AUTHOR]

High step-up voltage gain dc–dc converters are widely applied in fuel cell stacks, photovoltaic arrays, battery sources, and high intensity discharge lamps power systems. Active-network converters with coupled inductors (CL-ANC) are derived from switched inductor active-network converters (SL-ANC). The proposed converter contains two coupled inductors which can be integrated into one magnetic core and two power switches. The converter can provide a relatively high voltage conversion ratio with a small duty cycle; the voltage and current stress of power switches are low which is helpful to reduce the losses. This paper shows the key waveforms of the CL-ANC and detailed derivation of the steady-state operation principle. The voltage conversion ratio and the effect of the leakage inductance on voltage gain are discussed. The voltage stress and current stress on the power devices are illustrated and the comparison between the proposed converter and SL-ANC are given. Finally, the prototype has been established in the lab with 200 V and 400 V output under different turn ratios. Experimental results are given to verify the correctness of the analysis. [ABSTRACT FROM AUTHOR]

For low-cost isolated ac/dc power converters adopting high-voltage dc-link, research efforts focus on single-stage multilevel topologies. This paper proposes a new single-stage three-level isolated ac/dc PFC converter for high dc-link voltage low-power applications, achieved through an effective integration of ac/dc and dc/dc stages, where all of the switches are shared between two operations. With the proposed converter and switching scheme, input current shaping and output voltage regulation can be achieved simultaneously without introducing additional switches or switching actions. In addition, the middle two switches are turned on under zero current in discontinuous conduction mode operation, and the upper and bottom switches are turned on under zero voltage. Due to the flexible dc-link voltage structure, high power factor can be achieved at high line voltage. A 500 W/48 V prototype is designed to serve as the proof of concept, which exhibits 90.8% peak efficiency at low input line voltage. [ABSTRACT FROM AUTHOR]

In this paper, by investigating the topology derivation principle of the phase-shift-controlled three-level dc/dc converters, the modular multilevel dc/dc converters, by integrating the full-bridge converters and three-level flying capacitor circuit, are proposed for the high step-down and high power dc-based systems. The high switch voltage stress in the primary side is effectively reduced by the full-bridge modules in series. Therefore, the low-voltage-rated power devices can be employed to obtain the benefits of low conduction losses. More importantly, the voltage autobalance ability among the cascaded modules is achieved by the inherent flying capacitor, which removes the additional possible active components or control loops. In addition, zero-voltage-switching performance for all the active switches can be provided due to the phase-shift control scheme, which can reduce the switching losses. The circuit operation and converter performance are analyzed in detail. Finally, the performance of the presented converter is verified by the simulation and experimental results from a 2-kW prototype. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (M2Cs) are increasingly used in high-voltage direct current (HVDC) systems. The efficiency of M2Cs is influenced by the modulation and cell selecting methods, which determines the switching frequency and capacitor voltage ripple in the converter station. A new approach to modulation of the M2C is presented in this paper. Tolerance band methods are employed to obtain the switching instants, and also cell selection. The proposed methods overcome the modulation problem for converters with few cells on one hand and also reduce the sorting efforts for cell balancing purposes of many cells converter on the other hand. Three different algorithms are also proposed to balance the cell capacitor voltages. The evaluation is done in time-domain simulation by which the performance of each method is studied in both the steady-state and transient cases. It is observed that using tolerance band methods not only reduces the switching frequency but also allows for handling severe fault cases in a grid-connected system. Eventually, the most promising tolerance band method has been implemented and verified in a real-time digital simulator, RTDS®. The average switching frequency of 70 Hz has been achieved for the system under study, while the capacitor voltage ripple is limited to 10% of the nominal cell voltage. [ABSTRACT FROM AUTHOR]

Electrostatic actuators are being widely investigated to convert electrical energy into mechanical deformation in a broad variety of microrobotic applications. Both electrostatic gap closing and comb drive actuators require high excitation voltages for high performance operation. In the majority of applications, external bulky and heavy power supplies are used to provide such high voltages, which inevitably bring limitations on autonomous operation. One of the major challenges toward enabling operation of these systems without a bulky external power source is the development of ultralight and high power density power electronic interfaces (PEIs) with large step-up gains. In this paper, a special circuit topology, controlled by a pulse frequency modulation scheme, is introduced to meet stringent electrical and drive voltage requirements of electrostatic actuators. An ultracompact 63 mg (excluding PCB mass), 31.5 mm 2, and 500 mW PEI has been designed and fabricated. Experimental validations have been carried out to verify the circuit's ability to drive an 110-V-input electrostatic inchworm motor at 1-kHz actuating frequency. [ABSTRACT FROM AUTHOR]

The voltage gain of traditional boost converter is limited due to the high current ripple, high voltage stress across active switch and diode, and low efficiency associated with large duty ratio operation. High voltage gain is required in applications, such as the renewable energy power systems with low input voltage. A high step-up voltage gain active-network converter with switched-capacitor technique is proposed in this paper. The proposed converter can achieve high voltage gain without extremely high duty ratio. In addition, the voltage stress of the active switches and output diodes is low. Therefore, low voltage components can be adopted to reduce the conduction loss and cost. The operating principle and steady-state analysis are discussed in detail. A prototype with 20-40-V input voltage, 200-V output voltage, and 200-W output power has been established in the laboratory. Experimental results are given to verify the analysis and advantages of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, an isolated series asymmetrical half-bridge converter (SA-HBC) is proposed to satisfy the high power and high input-voltage requirements. In the proposed converter, two half-bridge modules with series configuration are adopted in the primary side to reduce the switch voltage stress to half of the input voltage. Moreover, the series half-bridge cells share the same transformer and leakage inductance, which simplifies the circuit structure. Zero-voltage-switching transition is achieved for all the active switches by employing the asymmetrical control scheme to reduce the switching losses. Furthermore, the voltages of the input capacitors are automatically balanced without any additional components or complex control methods. In addition, a family of dc–dc converters with series half-bridge structure is explored to give a universal discussion and extensive applications of the proposed contributions for the high input-voltage systems. Finally, a 500–600-V input 48-V output 1-kW prototype operating with 100 kHz switching frequency is built and tested to demonstrate the effectiveness of the proposed SA-HBC converter. The efficiency of 95% at full load is realized. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMC) are considered a top converter alternative for voltage-source converter (VSC) high-voltage, direct current (HVDC) applications. Main circuit design and converter performance evaluation are always important issues to consider before installing a VSC-HVDC system. Investigation into a steady-state analysis method for an MMC-based VSC-HVDC system is necessary. This paper finds a circular interaction among the electrical quantities in an MMC. Through this circular interaction, a key equation can be established to solve the unknown circulating current. A new steady-state model is developed to simply and accurately describe the explicit analytical expressions for various voltage and current quantities in an MMC. The accuracy of the expressions is improved by the consideration of the circulating current when deriving all the analytical expressions. The model's simplicity is demonstrated by having only one key equation to solve. Based on the analytical expressions for the arm voltages, the equivalent circuits for MMC are proposed to improve the current understanding of the operation of MMC. The feasibility and accuracy of the proposed method are verified by comparing its results with the simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, a novel high voltage gain single-stage dc/ac converter is proposed for distributed energy resources. A flyback-type auxiliary circuit is integrated with an isolated Ćuk-derived voltage source inverter to achieve a much higher voltage gain. It is seen that through this integration, the capacitors of the flyback and the Ćuk circuits are paralleled for charging and in series for discharging automatically. Due to the capacitive voltage dividing, the dc-side switch voltage stress can be reduced and the losses can be reduced as well. Besides, the low influence of coupling coefficient of flyback-type auxiliary circuit on the inverter characteristic renders the proposed inverter design rather flexible and easy. Steady-state characteristics, performance analysis, simulation and experimental results are given to show the merits of the proposed integrated inverter. Finally, based on the same integration concept, a family of different topologies is also presented for reference. [ABSTRACT FROM AUTHOR]

Within the photovoltaic (PV) power-generation market, the ac PV module has shown obvious growth. However, a high voltage gain converter is essential for the module's grid connection through a dc-ac inverter. This paper proposes a converter that employs a floating active switch to isolate energy from the PV panel when the ac module is off; this particular design protects installers and users from electrical hazards. Without extreme duty ratios and the numerous turns-ratios of a coupled inductor, this converter achieves a high step-up voltage-conversion ratio; the leakage inductor energy of the coupled inductor is efficiently recycled to the load. These features explain the module's high-efficiency performance. The detailed operating principles and steady-state analyses of continuous, discontinuous, and boundary conduction modes are described. A 15 V input voltage, 200 V output voltage, and 100 W output power prototype circuit of the proposed converter has been implemented; its maximum efficiency is up to 95.3% and full-load efficiency is 92.3%. [ABSTRACT FROM AUTHOR]

This paper proposes a center-tapped energy-recovery scheme used in the interleaved four-phase buck-based current source in continuous-conduction mode for electrical discharge machining (EDM). A pulse-machining current with high-slew rate is required for the EDM. Using the interleaving technique, the output-current slew rate of the buck-based current source can be improved because of the paralleled inductors at the start of discharge. The proposed center-tapped energy-recovery scheme provides a major path for the inductor to release its stored energy to avoid high-voltage stress in the output terminal when the gap is in the high-impedance state. The energy stored in the inductor is recovered to the input capacitor, and can be reused for machining. The experimental results are provided as the verification of the high-output-current slew rate and the energy recovery when the gap is in high-impedance state. [ABSTRACT FROM PUBLISHER]