Search

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

The pulse-width modulated (PWM) switching rectification that can achieve a high power factor (PF) for increasing the energy transfer efficiency between an LC resonator and a rectifier and voltage step-up and -down conversion is proposed for a wireless power transfer (WPT) receiver. The proposed method can emulate the switching rectifier as a resistive load by using an inductor and integrated phase synchronizers. Additionally, similar to a switched-inductor converter that controls the duty cycle ratio (D), the proposed PWM rectifier can control the output voltage VOUT when the input is a rectified, wirelessly coupled voltage instead of a constant voltage. Thus, unlike a conventional PWM switching rectifier for ac mains, an additional voltage conditioning circuit would not be needed after the proposed rectifier for WPT. The proposed PWM switching rectification is implemented in the AMS 0.18 μm 1.8 V/5 V CMOS process. PF = 1 is measured, indicating the most efficient energy transfer, compared to only 0.55–0.65 in a peak detection rectifier. Additionally, 88.2% of peak power conversion efficiency of the switching rectifier is achieved, and the maximum output power is 80.3 mW at 500 kHz of the WPT frequency. Moreover, the measured voltage conversion ratios ranging between 0.73× and 2× are demonstrated in this paper. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

Switch fault diagnosis is an important design aspect for pulse width modulation (PWM) dc-dc power converters. It can prevent power converters from further damage, and also make preparations for remedial actions. In this paper, a fast switch fault diagnostic method is proposed for PWM dc-dc converters operating in continuous conduction mode. The proposed method utilizes the magnetic component (inductor or transformer) voltage for fault diagnosis. Based on the real-time voltage measurement and switch gate-driver signals, characteristics of switch open-circuit faults and short-circuit faults are rapidly extracted, and thus, switch faults can be quickly detected. The magnetic component voltage can be measured by an auxiliary winding in the magnetic core, and gate-driver signals can be easily got from the control circuit. Moreover, the fault detection can be implemented by a low-cost logical hardware circuit, and this circuit can be integrated into the control circuit. The fault diagnosis principle, design considerations, and implementation are discussed in this paper. Experiments are conducted to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques. [ABSTRACT FROM AUTHOR]

Power systems for exploration rovers tend to be complex as three separate converters are necessary; in addition to a main dc–dc converter and cell equalizer for rechargeable energy storage cells, an equalizer for photovoltaic (PV) modules is desirably equipped in order to preclude negative impacts of partial shading. This paper proposes the pulse width modulation (PWM) converter integrating voltage equalizers for PV modules and energy storage cells. The proposed integrated converter comprises a switched capacitor converter, PWM buck converter, and series-resonant voltage multiplier that perform PV equalization, power conversion from the PV modules to the load, and cell equalization, respectively. Three converters can be integrated into a single unit with reducing the total switch counts, achieving not only system-level but also circuit-level simplifications. The derivation procedure of the integrated converter is explained, followed by the operation analysis. Experimental tests were performed using series-connected supercapacitor (SC) modules and solar array simulators to emulate a partial shading condition. With the integrated converter, the extractable maximum power from the PV modules significantly increased while voltage imbalance of SC modules was adequately eliminated, demonstrating the integrated performance of the proposed converter. [ABSTRACT FROM AUTHOR]

Dynamic voltage restorer (DVR) technology has become a mature power quality product. In high-power applications, DVR using a multilevel converter is commonly used. However, DVR using a multilevel direct pulse width modulation (PWM) ac–ac converter has not been well studied. This paper presents a new DVR topology using a cascaded multilevel direct PWM ac–ac converter. In the proposed scheme, the unit cell of the multilevel converter consists of a single-phase PWM ac-ac converter using switching cell structure with coupled inductors. Therefore, the multilevel converter can be short- and open-circuited without damaging the switching devices. Neither lossy RC snubber nor a dedicated soft commutation strategy is required in the proposed DVR. This improves the reliability of the DVR system. The output voltage levels of the multilevel converter increase with the number of cascaded unit cells, and a high ac output voltage is obtained by using low-voltage-rating switching devices. Furthermore, a phase-shifted PWM technique is applied to significantly reduce the size of the output filter inductor. A 1-kW prototype of single-phase DVR is developed, and its performance is experimentally verified. Finally, the simulation results are shown for a three-phase DVR system. [ABSTRACT FROM AUTHOR]

This paper proposes a current-fed isolated bidirectional dc–dc converter (CF-IBDC) that has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes of the low-voltage (LV) side switches in the proposed converter can be eliminated without additional clamp circuits. The converter adopts the pulse width modulation plus hybrid phase-shift control scheme such that the bus voltage can match the output voltage by means of the transformer. Thus, the current stresses and conduction losses of the converter become lower. In addition, the practical zero voltage switching (ZVS) of the secondary-side switches can be realized by adjusting the phase-shift angle within the secondary side when in light load or no load condition. The operating principles and characteristics including the power transfer, root-mean-square (RMS) current, and soft switching are investigated in detail. Then the design guidelines of inductors are also given. Finally an experimental prototype with 30–60 V input and 400 V/2.5 An output is built to verify the correctness of theoretical analyses. [ABSTRACT FROM PUBLISHER]

This paper focuses on the common dc-link voltage between a three-phase diode rectifier and a modular multilevel cascade inverter based on double-star chopper cells (MMCI-DSCC) for a medium-voltage motor drive. This motor drive can be operated even when no capacitor exists on the dc link. However, a nonnegligible, but predictable, amount of switching-ripple voltage occurs on the dc link. This paper achieves modeling and analysis of the switching-ripple voltage, thus making it possible to design a small-sized dc passive filter consisting of series connection of a film capacitor and a damping resistor. A 400-V, 15-kW down scaled system is used to confirm the effectiveness of the analysis and the dc filter. Experimental results show that the switching-ripple voltage can be attenuated satisfactorily by the dc filter, and that the power loss dissipated in the damping resistor is negligible, compared to the rated power of 15 kW. [ABSTRACT FROM AUTHOR]

This paper proposes a pulse-width modulation three-level converter with reduced filter size using two transformers. The proposed converter has many advantages. All switches sustain only the half of the input voltage and since the secondary rectified voltage is a three-level waveform, the output filter inductor can be reduced. Also, because of the power sharing of transformer and reduced output inductor, high efficiency can be obtained. The operational principle, analysis, and design considerations of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results from a prototype with 600 W, 500-600 V input, and 60 V output. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

A simple scheme to realize phase-disposition carrier pulse width modulation (PD PWM) for parallel two-level voltage-source converters (2L-VSCs) is presented in this paper. The proposed implementation only uses a single carrier signal and can easily be implemented using a digital signal processor. The operation of the parallel VSCs with the coupled inductor (CI) under the PD PWM is briefly discussed, and the associated dc flux injection problem is investigated. A CI saturation issue during the band transition under the PD PWM scheme is also explored, and the strategy to avoid this problem is presented. In addition, the proposed strategy also maintains a volt–second balance to synthesize desired reference space voltage vector during the band transition. As a result, a smooth transition from one modulation band to the other is ensured without causing disturbances in the line-to-line voltage. The switching losses and the harmonic performance of the proposed implementation are also compared with the commonly used phase-shifted carrier pulse width modulation. The implementation issues are discussed and the experimental results are also presented. [ABSTRACT FROM AUTHOR]

Primary-side controlled universal-line flyback converters have been widely used in low-power applications due to their simplicity, low standby power, and low cost. However, conventional OCP schemes normally cause too large a variation in output current when the input voltage varies. This paper proposes a self-compensating OCP circuit to achieve a high-precision constant current at different input voltages which can be used in flyback converters working in discontinues conduction mode. It consists of a CS S/H circuit and a dynamic OCP voltage reference circuit. Compared with conventional OCP circuits, it does not need an extra compensation circuit. To verify the feasibility and performance of the proposed circuit, an IC controller that uses the proposed OCP circuit has been designed and fabricated in 0.35 μm 5-V/40-V high-voltage CMOS technology. Experimental results show that the constant output current precision of the prototype is within ±1% when the input line voltage changes from 85 to 265 Vac. In the common line voltage range (\rm110-220\ Vac ), the output current regulation accuracy can reach a level as high as ± 0.3%. [ABSTRACT FROM AUTHOR]

Multiple output converters (MOCs) are widely applied to applications requiring various levels of output voltages due to their advantages in terms of cost, volume, and efficiency. However, most of the conventional MOCs cannot regulate multiple outputs tightly and they can barely avoid the cross-regulation problem. In this paper, the recently developed time-division multiple control (TDMC) method, which can regulate all of the outputs with a high accuracy, is used for a multiple output battery charger based on the phase-shift full-bridge topology to simultaneously charge three batteries. The proposed charger is able to charge three different kinds of batteries or three of the same kind of battery in different state of charges (SOCs) independently and accurately with the constant current/constant voltage (CC/CV) charge method. As a result, the strict ripple specification of a battery can be satisfied for multiple battery charges without difficulty. In addition, the proposed charger exhibits a high efficiency since the soft switching of all of the switches during the entire charge process can be guaranteed. The operating principle of the converter and the design of the controller, including the state-space average modeling, will be detailed, and the validity of the proposed method is verified through experiments. [ABSTRACT FROM PUBLISHER]

A family of isolated buck–boost dc/dc converter for wide input-voltage range is proposed in this paper, and the full-bridge (FB) boost converter, being one of the typical topologies, is analyzed. Due to the existence of the resonant inductor (including the leakage inductor), the FB-boost converter can only adopt the two-edge-modulation (TEM) scheme with the FB cell being leading-edge modulated and the boost cell being trailing-edge modulated to minimize the inductor current ripple over the input-voltage range, and a phase-shift-control-scheme-based TEM with the use of the market available controller IC such as UC3895 is proposed, which realizes phase-shifted control for the FB cell to achieve zero-voltage switching. In order to improve the reliability and efficiency of the FB-boost converter, a three-mode dual-frequency control scheme is proposed, in which the FB-boost converter operates in boost, FB-boost and FB modes in low, medium and high input voltage regions, respectively, and for which the expression of the inductor current ripple is derived in this paper. As the input voltage in the FB-boost mode is close to the output voltage, the inductor current ripple in this mode is much smaller than that in the other modes, and the switching frequency of the boost cell in this mode can be lowered to one-(2N+1)th of the preset switching frequency to reduce the switching loss, and hence, to improve the efficiency. A 250–500 V input, 360 V output, and 6 kW rated power prototype is fabricated to verify the effectiveness of the design and control method. The average efficiency over the input-voltage range is 96.5%, and the highest efficiency attained is 97.2%. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase power factor corrector based on a tapped-inductor buck–boost converter. This paper suggests simplified models of the power stage under current-mode control and derives small-signal transfer functions of both the current and voltage control loops. Design rules for implementation of the proposed power factor corrector (PFC) are also suggested. The proposed PFC features low dc bus voltage, arbitrary lower than the peak line voltage. The proposed PFC is suitable for applications in computers and communications, where dc isolation can be provided by the downstream dc/dc converters. Simulation and experimental results are also reported and stand in good agreement with theoretical expectations. [ABSTRACT FROM AUTHOR]

A new zero-voltage-switched bidirectional dc–dc converter with coupled inductors is proposed in the paper. The proposed converter can operate with a steep conversion ratio, soft switching, a continuous inductor current, and fixed switching frequency. It can also operate with the switch stresses of a conventional pulsewidth-modulation-tapped/coupled-inductor converter regardless of the direction of power flow and without any voltage spikes across the switches during turn-OFF. These features are due to a very simple auxiliary circuit that is operational regardless of the direction of power flow and absorbs energy from the leakage inductance of the coupled inductors during switch turn-OFF. In the paper, the operation and design of the converter are discussed and its feasibility is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a new type of ac–ac converter which can operate as traditional noninverting buck and boost converters, and inverting buck–boost converter as well. The proposed converter uses six unidirectional current flowing and bidirectional voltage blocking switches, implemented by six reverse blocking insulated-gate bipolar transistors (IGBTs) or series mosfet–diode pairs, two input and output filter capacitors, and one inductor. It has no shoot-through problem of voltage source (or capacitor) even when all switches are turned-on, and therefore, pulsewidth modulation dead-times are not needed resulting in high-quality waveforms, and solves the commutation problem without using bulky and lossy RC snubbers or dedicated soft-commutation strategies. It has smaller switching losses because only two switches out of six are switched at high frequency during each half-cycle of input voltage, and it can use power MOSFETs as body diode never conducts, making it immune from mosfet failure risk which otherwise may occur due to poor reverse recovery problem of body diode. The noninverting buck–boost mode of the proposed converter can be used in applications with both step-up and step-down demand, while the inverting buck–boost mode can also be used in its application as dynamic voltage restorer. Detailed analysis of the proposed converter is given, and experimental results are also provided. [ABSTRACT FROM AUTHOR]

Soft-start strategy is very important for boost converters to guarantee the stability of the output voltage. However, previous methods may cause large initial inrush current and long output voltage settling time. In this paper, a variable ramp-slope with predefined voltage (VRSPV) soft-start strategy is proposed. As a result, one branch of the initial inrush current is successfully eliminated and the output settling time of the boost converter is shortened by using the variable slope soft-start voltage. Also, an adaptive inrush current suppressing (AICS) technique is designed. The series resistance of the output capacitor is adaptively regulated by AICS technique to further suppress the initial inrush current. Finally, the VRSPV strategy and AICS technique are combined and implemented in a voltage-mode boost converter. The measurement results show that the peak initial inrush current and settling time are decreased by 60% and 40%, respectively. The output voltage of the boost converter increases smoothly during the soft-start period and finally achieves stability. The proposed method of combining VRSPV strategy and AICS technique is very suitable to be integrated on a chip to save the printed circuit board area and cost. [ABSTRACT FROM AUTHOR]

This paper proposes a novel single-phase ac–ac Z-source converter based on the Γ-structure. The proposed converter uses a coupled transformer to produce the required gain. The obtained gain can be tuned by varying the turn ratio $\gamma _\Gamma$ of the transformer within the narrow range of $1 < \gamma _\Gamma < 2$. Also, the gain factor increases with decrease of the transformer turns ratio, $\gamma _\Gamma$ . Small transformer turn ratio results in more practical topology in some voltage gains. It makes the transformer design easier and reduces construction cost. Also, in the proposed topology, the input and output voltages share the same ground. In order to avoid voltage and current spikes on the switches, a commutation strategy is proposed and safe commutation is achieved without using a snubber circuit. The operating principles and steady-state analyses are presented to verify the operational concept of the proposed topology. Also, experimental results are given to verify the validation of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, an analysis and calculation of the dc-link current and voltage ripples are presented for a three-phase inverter with unbalanced load. A comparison of the dc-link average and root-mean-square (rms) currents between considering and ignoring high frequency harmonics of the output current is drawn. It is shown that high frequency harmonic currents have little effect on the dc-link current, and therefore, they can be ignored. Based on the symmetrical components method, the dc-link average and harmonic rms currents are derived, and the dc-link voltage ripple is compared between the balanced and unbalanced loads. It can be found that the dc-link current and voltage ripples consist of not only high frequency harmonics but also the double fundamental frequency harmonic, and the voltage ripple is independent of the positive-sequence component and determined by the negative-sequence component, under the unbalanced load. Experimental results are shown to verify the accuracy of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a novel single-phase five-level inverter is proposed using coupled inductors. This inverter can output five-level voltage with only one dc source. No split of the dc voltage capacitor is needed, totally avoiding the voltage balancing problem in conventional multilevel inverters. The level of the output voltage is only half of the dc-link voltage in all conditions, leading to much reduced dv/dt . This inverter is based on the widely used three-arm power module and the voltage stresses on all the power switches are the same, making it very easy to construct. Operation mechanism of this inverter is analyzed and the possible switching patterns are investigated. Based on these analyses, a novel optimized modulation scheme is presented. With this modulation method, no dc components exist in the inductor currents, which is very helpful for minimization of the inductors. Simulation and experimental results show the validity of the proposed inverter together with the optimized modulation scheme. [ABSTRACT FROM AUTHOR]

This paper presents an alternative to the traditional dc-dc converter interfacing the battery with the inverter dc bus in plug-in hybrid electric vehicle (HEV) traction drives. The boost converter used in commercial HEVs meets with obstacles when it comes to upgrading the power rating and achieving high efficiency while downsizing the converter. A four-level flying-capacitor dc-dc converter is explored that can overcome these drawbacks by dramatically reducing the inductance requirement. A special case of the four-level converter, the 3X dc-dc converter, operates at three discrete output/input voltage ratios, thus further reducing the inductance requirement to a minimal value (almost zero). When further compared to its switched-capacitor dc-dc converter counterparts, the 3X dc-dc converter can be operated at variable output/input voltage ratios without sacrificing efficiency, and it lowers the capacitance requirement by utilizing the parasitic inductance. The operating principle, current ripple analysis, the transient control to limit the inrush current, and power loss analysis are introduced. Experimental results of a 55-kW prototype are provided to demonstrate the principle and analysis of this topology. [ABSTRACT FROM AUTHOR]