Search

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

Inductor current is an important feedback parameter in synchronous buck converters (SBCs). It is used for overcurrent protection, current sharing among interleaved modules, and current-mode feedback regulation, among others. While implementing a digital controller, inductor current is sensed and fed into the controller through a high sampling frequency analog to digital converter (ADC). As the switching frequency of the converter becomes higher, the need for an even higher sampling frequency ADC also goes up, which is a distinct disadvantage in terms of the overall cost. This paper discusses a simple current estimation technique that avoids use of any expensive current sensor and high sampling frequency ADCs. The paper shows that in a buck converter, inductor current can be estimated by tracking the width of the switch node voltage. Implementation and limitations of the proposed current estimation scheme are discussed in detail. The proposed method is validated using a 3.3 V–15 A SBC prototype and results show the estimation technique is accurate within 5% with a converter switching frequency of 800 kHz. In order to prove the effectiveness of the technique in feedback regulation, the current estimation technique is used to implement average current mode and hysteretic current mode control on a SBC. To prove the effectiveness of the proposed current estimation scheme, it is used in closed-loop control of the SBC to verify the dynamic responses, such as start-up transient, step change in load, and reference. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

A novel PWM full bridge (FB) dc–dc converter for large power industrial applications is proposed in this paper. The soft switching mode of the primary switches can be varied under different input and output conditions to achieve optimum system efficiency. In the zero-voltage and zero-current switching (ZVZCS) mode, the turn-on and turn-off switching loss can be optimized because the soft switching conditions of the turn-on and turn-off instants are well decoupled. In the zero-voltage switching (ZVS) mode, the turn-off switching loss can also be optimized because there is no requirement for light load operation in this mode. Four mosfets with ultra-low on-state resistance are used, thus, the added conduction loss is small. The auxiliary mosfets with high switching frequency are turned on with zero-current and off with zero-voltage, hence, the added switching loss can also be neglected. Furthermore, some drawbacks of the conventional ZVS and ZVZCS converters, e.g., narrow ZVS load range, high primary circulating current, incomplete reset of the primary current, and unreasonable VA rating of the added components, have been well solved. The operation principles and soft switching characteristics are discussed. Experimental results from an 18-kW prototype are provided to verify the proposed converter. [ABSTRACT FROM AUTHOR]

The inductance is an important parameter impacting current ripple calculation, usually with the assumption that the designed inductance performs ideally in most of voltage source inverters (VSIs) applications. However, the initial permeability of magnetic material usually descends when the winding current reaches or goes beyond the saturation limit. In such region of saturation, the implemented inductor does not perform as expected in design stages and its value varies with the bias current. In this paper, analysis and calculation of the current ripple are presented for a three-phase VSI with powder cores-based inductors, which reveals the calculation error of current ripple caused by the soft saturation nature of powder cores. Based on the equivalent single-phase model, the influence of inductance saturation on current ripple can be quantitatively evaluated. Then, a comparison of the current ripple calculation between considering and ignoring inductance saturation of implemented inductors is drawn in detail. Furthermore, under the condition of inductance saturation, the output current ripple peak-to-peak value of three phases is used as the constraint for variable switching frequency pulsewidth modulation (VSFPWM) design. A comprehensive method is developed to compensate the effect of inductance saturation in VSFPWM. At last, the effectiveness of the proposed strategy is verified by the detailed simulation and experiment. [ABSTRACT FROM AUTHOR]

The pulse-width modulated (PWM) switching rectification that can achieve a high power factor (PF) for increasing the energy transfer efficiency between an LC resonator and a rectifier and voltage step-up and -down conversion is proposed for a wireless power transfer (WPT) receiver. The proposed method can emulate the switching rectifier as a resistive load by using an inductor and integrated phase synchronizers. Additionally, similar to a switched-inductor converter that controls the duty cycle ratio (D), the proposed PWM rectifier can control the output voltage VOUT when the input is a rectified, wirelessly coupled voltage instead of a constant voltage. Thus, unlike a conventional PWM switching rectifier for ac mains, an additional voltage conditioning circuit would not be needed after the proposed rectifier for WPT. The proposed PWM switching rectification is implemented in the AMS 0.18 μm 1.8 V/5 V CMOS process. PF = 1 is measured, indicating the most efficient energy transfer, compared to only 0.55–0.65 in a peak detection rectifier. Additionally, 88.2% of peak power conversion efficiency of the switching rectifier is achieved, and the maximum output power is 80.3 mW at 500 kHz of the WPT frequency. Moreover, the measured voltage conversion ratios ranging between 0.73× and 2× are demonstrated in this paper. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

In several electrical dc–ac power conversions, the ac output voltage is higher than the input voltage. If a voltage-source inverter (VSI) is used, then an additional dc–dc boosting stage is required to overcome the step-down VSI limitations. Recently, several impedance source converters are gaining higher attentions [1], [2], as they are able to provide buck-boost capability in a single conversion stage. This paper proposes the merging of the boost stage and the VSI stage in a single stage dc–ac power conversion, denoted as split-source inverter (SSI). The proposed topology requires the same number of active switches of the VSI, three additional diodes, and the same eight states of a conventional space-vector modulation. It also shows some merits compared to Z-source inverters, especially in terms of reduced switch voltage stress for voltage gains higher than 1.15. This paper presents the analysis of the SSI and compares different modulation schemes. Moreover, it presents a modified modulation scheme to eliminate the low frequency ripple in the input current and the voltage across the inverter bridge. The proposed analysis has been verified by simulation and experimental results on a 2.0-kW prototype. [ABSTRACT FROM PUBLISHER]

Pulse-width-modulated (PWM) converters have been widely applied for power processing, and they are typically the stems of other types of converters, such as quasi-resonant, Z-source, and switched-inductor hybrid converters. Development of PWM converters has been spanning over a century, starting from the buck converter. The well-known PWM converters include buck, boost, buck–boost, Ćuk, single ended primary inductive converter (SEPIC), zeta, Z-source, quasi-Z source, etc. Many attempts have been proposed to develop these converters based mostly on canonical cell concepts and by introducing extra LC filters to the cells. This paper presents an enhancement to the layer and graft schemes by introducing the ideas of dc voltage/current offsetting, capacitor/inductor component splitting, diode grafting, and inverse operation of PWM converters. The PWM converters, which can be operated in continuous conduction mode (CCM) or discontinuous conduction mode (DCM), therefore can be synthesized systematically according to decoded transfer gains. Decoding and synthesizing PWM converters uniquely bridge transfer gains to converter topologies and provide readers a comprehensive understanding of PWM-converter evolution from the original converter, the buck converter. Additionally, in this paper, the Ćuk, SEPIC, and zeta converters all with the same transfer gain of $D/(1 - D)$ are proved to be equivalent to the buck–boost converter with an extra LC filter. For further illustrating the proposed approaches, various types of Z-source converters, switched-capacitor/switched-inductor hybrid converters, and a single-stage interleaved converter are reviewed, and new PWM converters are developed. [ABSTRACT FROM AUTHOR]

This paper proposed a novel family of pulsewidth modulation (PWM) strategies for single-phase quasi-switched boost inverter (qSBI). By combining shoot-through (ST) mode in the inverter's switches and the turning-on state of an additional switch, the qSBI produced a high voltage gain without adding any passive components. Compared to the conventional PWM strategy for the same input and output voltage gain, the introduced PWM strategies for qSBI could reduce voltage stress across semiconductors and capacitor with the following additional merits: having smaller high-frequency inductor current and capacitor voltage ripples, using high modulation index with low ST duty cycle, and having higher efficiency. Circuit analysis, operating theories, and simulation results of the single-phase qSBI with the introduced PWM5 strategy are shown. A 500-W laboratory prototype was constructed and the effectiveness of the introduced PWM strategy was validated. The qSBI with the proposed PWM strategies is suitable for applications where the required voltage gain lies between 2 and 3. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems containing a rechargeable battery as an energy buffer require multiple dc–dc converters for PV panel control and battery regulation, and hence, they are prone to be complex and costly. To simplify the system by reducing the number of converters, this paper proposes the nonisolated switched capacitor converter (SCC)-based multiport converter (SC-MPC) for standalone PV systems. The proposed SC-MPC can be derived by integrating a bidirectional pulsewidth modulation (PWM) converter, series-resonant converter (SRC), and an SCC with sharing switches. PWM and pulse frequency modulation (PFM) controls are employed for the PWM converter and SRC, respectively, to regulate either a battery voltage, output voltage, or input power from a PV panel, depending on power balance among the input, battery, and load. The 150-W prototype was built for an experimental verification, and the results demonstrated the output voltage could be regulated independently on the battery voltage or input port of PV panels. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

In this paper, a novel direct ac–ac converter based on the coupled inductor Z-source networks is proposed that offers a wide range of buck–boost operation. A total of two Z-source networks, called the coupled switched inductor and the modified switched coupled inductor, are employed that enable the ac–ac converter to deliver a wide voltage range. The proposed converter with both networks provides free-wheeling current paths for the inductors currents during the state transitions, which results in solving the commutation problems and the need for snubber circuits. A simple switching strategy is then proposed that helps to share a common magnetic core between the coupled inductors. For any particular voltage gain, the proposed structures require a smaller duty cycle compared to the conventional ones; therefore, a smaller inductance is required. Simulation and experimental results are provided to confirm the theoretical achievements. [ABSTRACT FROM AUTHOR]

Recent power systems, such as renewable energy systems consisting of solar panels and rechargeable batteries, contain multiple power sources and need multiple converters in proportion to the number of power sources, resulting in increased system complexity and cost. This paper proposes a multiport converter (MPC) integrating a bidirectional PWM converter and series-resonant converter. Not only is the switch count halved with the proposed MPC, but also magnetic components can be integrated, reducing the circuit complexity and volume. A 150-W prototype of the proposed MPC was built for the experimental verification. The measured voltage conversion characteristics and transient responses demonstrated that the proposed MPC could control load and battery voltages independently by pulse width modulation and pulse frequency modulation controls, respectively. [ABSTRACT FROM AUTHOR]

In order to incorporate the advantage of the $V^{2}$ control scheme and the benefits of digital implementation, this paper proposes a digital $V^{2}$ control with hybrid capacitor current ramp compensation, which includes the estimated output capacitor current ramp and the external ramp. Since capacitor current responds to the load change immediately, the proposed method has faster transient response than either digital inductor current compensation or external ramp compensation. The proposed estimator does not require high sampling rate and avoids the current ramp distortion due to the parasitic resistance and inductance. The small-signal model is derived by describing function to understand the dynamic characteristics of the proposed control scheme. The model provides design criteria of the current feedback gain and the external ramp slope. The effectiveness of the proposed control architecture and the current ramp estimator is verified by simulation and experimental results. Compared with the benchmark, the proposed control has 70% reduction on settling time and 20% reduction on undershoot deviation. [ABSTRACT FROM AUTHOR]

This paper proposes a new bidirectional three-phase push–pull converter that has a simple structure and achieves zero-voltage switching turn-on of switches. Also, due to use of a single inductor, an imbalance among phase currents on the low-voltage high-current side is trivial in the proposed converter although no current sharing control is employed. In this paper, a new dual asymmetrical pulse width modulation (PWM) switching method is proposed for bidirectional power flow control with seamless mode change. The proposed switching method offers reduced circulating current and makes the converter easier to implement compared to the PWM plus phase shift-based control method since it is a general PWM method having two independent duty cycle controls on each side. Experimental results from a 3-kW prototype are provided to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

Switch fault diagnosis is an important design aspect for pulse width modulation (PWM) dc-dc power converters. It can prevent power converters from further damage, and also make preparations for remedial actions. In this paper, a fast switch fault diagnostic method is proposed for PWM dc-dc converters operating in continuous conduction mode. The proposed method utilizes the magnetic component (inductor or transformer) voltage for fault diagnosis. Based on the real-time voltage measurement and switch gate-driver signals, characteristics of switch open-circuit faults and short-circuit faults are rapidly extracted, and thus, switch faults can be quickly detected. The magnetic component voltage can be measured by an auxiliary winding in the magnetic core, and gate-driver signals can be easily got from the control circuit. Moreover, the fault detection can be implemented by a low-cost logical hardware circuit, and this circuit can be integrated into the control circuit. The fault diagnosis principle, design considerations, and implementation are discussed in this paper. Experiments are conducted to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

Soft switching pulse-width modulation (PWM) dc–dc full-bridge converter with controlled rectifier on the secondary side of the high-frequency power transformer is presented in this paper. An active secondary switch, including new nondissipative passive energy recovery turn-off snubber on the secondary side and modified PWM control algorithm, provide conditions for zero-voltage and zero-current turn-on and zero-current turn-off of IGBT transistors on the primary side of the high-frequency dc–dc converter. The simple passive energy recovery snubber ensures also zero-voltage turn-off of the transistor on the secondary side of the power transformer. The principle of operation is explained and analyzed and consequently verified on a 2 kW, 50 kHz laboratory model of the converter. [ABSTRACT FROM PUBLISHER]

This paper proposes a pulse width modulation plus phase-shift (PPS) control for nonisolated high gain soft-switching bidirectional dc–dc converter (HSBDC). The phase-shift angle is used to control the direction and amount of power flow of the bidirectional dc–dc converter, while the duty cycle is used to balance the voltage between two high voltage side (HVS) capacitors. The HSBDC with PPS control has the advantages of simple control structure and symmetrical switching patterns, ensured soft-switching in both forward and backward modes at all load under wide voltage range, and reduced voltage ratings of the HVS capacitors and switches. The operation principle of the HSBDC with PPS control is analyzed in detail. Based on the analysis the passive component is designed to achieve higher efficiency. A 3-kW prototype is implemented and tested to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

This paper introduces series work of common-mode (CM) voltage reduction for the paralleled inverters. The paralleled inverters’ phase-legs are connected through coupling inductors and the combined three-phase currents are provided to the load. Interleaving is an approach to reduce the CM voltage for the paralleled inverters but it cannot eliminate CM voltage. A novel pulse-width-modulation (PWM) method for paralleled inverters which can theoretically achieve zero CM voltage is developed. Considering the basic voltage vectors in each inverter, novel paralleled voltage vectors which have zero CM voltage are proposed to combine the reference voltage vector. The action time's distribution and voltage vectors’ sending sequence for each inverter are also introduced. The proposed PWM method can make sure the voltage of the two inverters are balanced in each switching cycle and limits the circulating current through small coupling inductors. Similar to interleaving space vector PWM, the proposed zero CM PWM also has the ability to reduce the output current ripple and electromagnetic interference (EMI). Simulation and experimental results are provided to show the advantage of paralleled inverters in CM voltage reduction and validate the proposed method has good performance to reduce CM current and CM EMI noise. [ABSTRACT FROM PUBLISHER]

A dual-buck inverter (DBI) possesses no shoot-through worries and can boost efficiency by using power mosfet s. The main drawback of a DBI is the use of more inductors than in a traditional full-bridge inverter. This greater number of inductors decreases the power density and increases system cost. In this paper, a modified cascaded full-bridge DBI is proposed. It retains all the advantages of the conventional cascaded full-bridge DBI, possesses no shoot-through issues, and can be operated with no pulse-width-modulation dead-times. It can be implemented with power mosfet without reverse recovery issues of a body diode to boost efficiency. The cascaded modules in the proposed inverter share current limiting inductors. Therefore, the number of inductors and inductor footprints, the complexity of the circuit layout, required inductance, and magnetic volume can all be decreased. To show the advantages of the proposed inverter, detailed theoretical analysis and experimental results are provided. [ABSTRACT FROM PUBLISHER]

ZSVM1, ZSVM2, and ZSVM6 are three traditional space vector modulation (SVM) strategies for three-phase Z-source inverter. The shoot-through times of ZSVM1, ZSVM2, and ZSVM6 are divided into two equal parts, four equal parts, and six equal parts, respectively. Although these control strategies are easy to be implemented in program, their inductor current ripples are not optimized, causing large current ripple. This paper proposes new SVM strategies, named ZSVMD6 and ZSVMD1, for reducing inductor current ripples of Z-source inverter. The principle of volt–second balance is used in the proposed strategies to divide shoot-through times in real time. So every divided shoot-through time is not equal, and changing in real time. The divided shoot-through time can ensure that the sum of the inductor charging current ripple and discharging current ripple is zero at each time, therefore reducing the inductor current ripples. The derivation details of the proposed strategies are given. The inductor current ripples of the proposed strategies and traditional ones are compared and analyzed. Simulation and experiment results show that the inductor current ripples of the proposed strategies are much lower than that of the traditional ones, verifying the effectiveness of the proposed strategies. [ABSTRACT FROM PUBLISHER]

To prevent partial-shading issues in photovoltaic (PV) systems, various kinds of voltage equalizers that virtually unify characteristics of shaded and unshaded modules have been proposed. Although PV string utilization can be dramatically improved, PV systems tend to be complex and costly because, in addition to the main converter for string control, voltage equalizers are separately necessary. This paper proposes the single-switch single-magnetic pulse width modulation (PWM) converter integrating the voltage equalizer using the series-resonant voltage multiplier (SRVM) for standalone PV systems. By utilizing a square wave voltage generated across a filter inductor in a PWM buck converter for driving the SRVM, the main PWM converter and voltage equalizer can be integrated into a single unit with reducing the total switch and magnetic component counts, achieving not only system-level but also circuit-level simplifications. The experimental test using the prototype for three PV modules connected in series was performed emulating a partial-shading condition. The integrated converter effectively precluded the partial-shading issues and significantly improved the power available at a load, demonstrating its efficacy. [ABSTRACT FROM AUTHOR]

This paper first starts with reviewing several commonly practiced PWM schemes for the three-phase isolated buck matrix-type rectifier. Then, an optimal six-segment PWM scheme (“Type A”) is proposed. The analysis shows “Type A” PWM scheme has lower duty-cycle loss, maximum output inductor current ripple, and minimum switching loss comparing with other PWM schemes when the mosfet devices are employed. In addition, a low input current total harmonic distortion (THD) can be achieved with duty-cycle compensation. Finally, the steady-state analysis of duty-cycle loss, inductor current ripple, and THD are all compared and verified by the experimental results for “Type A” PWM and eight-segment PWM (“Type E”). [ABSTRACT FROM PUBLISHER]

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques. [ABSTRACT FROM AUTHOR]

Power systems for exploration rovers tend to be complex as three separate converters are necessary; in addition to a main dc–dc converter and cell equalizer for rechargeable energy storage cells, an equalizer for photovoltaic (PV) modules is desirably equipped in order to preclude negative impacts of partial shading. This paper proposes the pulse width modulation (PWM) converter integrating voltage equalizers for PV modules and energy storage cells. The proposed integrated converter comprises a switched capacitor converter, PWM buck converter, and series-resonant voltage multiplier that perform PV equalization, power conversion from the PV modules to the load, and cell equalization, respectively. Three converters can be integrated into a single unit with reducing the total switch counts, achieving not only system-level but also circuit-level simplifications. The derivation procedure of the integrated converter is explained, followed by the operation analysis. Experimental tests were performed using series-connected supercapacitor (SC) modules and solar array simulators to emulate a partial shading condition. With the integrated converter, the extractable maximum power from the PV modules significantly increased while voltage imbalance of SC modules was adequately eliminated, demonstrating the integrated performance of the proposed converter. [ABSTRACT FROM AUTHOR]

Dynamic voltage restorer (DVR) technology has become a mature power quality product. In high-power applications, DVR using a multilevel converter is commonly used. However, DVR using a multilevel direct pulse width modulation (PWM) ac–ac converter has not been well studied. This paper presents a new DVR topology using a cascaded multilevel direct PWM ac–ac converter. In the proposed scheme, the unit cell of the multilevel converter consists of a single-phase PWM ac-ac converter using switching cell structure with coupled inductors. Therefore, the multilevel converter can be short- and open-circuited without damaging the switching devices. Neither lossy RC snubber nor a dedicated soft commutation strategy is required in the proposed DVR. This improves the reliability of the DVR system. The output voltage levels of the multilevel converter increase with the number of cascaded unit cells, and a high ac output voltage is obtained by using low-voltage-rating switching devices. Furthermore, a phase-shifted PWM technique is applied to significantly reduce the size of the output filter inductor. A 1-kW prototype of single-phase DVR is developed, and its performance is experimentally verified. Finally, the simulation results are shown for a three-phase DVR system. [ABSTRACT FROM AUTHOR]

This paper proposes a current-fed isolated bidirectional dc–dc converter (CF-IBDC) that has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes of the low-voltage (LV) side switches in the proposed converter can be eliminated without additional clamp circuits. The converter adopts the pulse width modulation plus hybrid phase-shift control scheme such that the bus voltage can match the output voltage by means of the transformer. Thus, the current stresses and conduction losses of the converter become lower. In addition, the practical zero voltage switching (ZVS) of the secondary-side switches can be realized by adjusting the phase-shift angle within the secondary side when in light load or no load condition. The operating principles and characteristics including the power transfer, root-mean-square (RMS) current, and soft switching are investigated in detail. Then the design guidelines of inductors are also given. Finally an experimental prototype with 30–60 V input and 400 V/2.5 An output is built to verify the correctness of theoretical analyses. [ABSTRACT FROM PUBLISHER]

A new soft-switching pulse-width-modulated (PWM) full-bridge converter is proposed in this paper. The proposed converter has zero voltage switching (ZVS) in all its switches with fewer conduction losses than other ZVS-PWM full-bridge converters, due to a novel auxiliary circuit scheme. In this paper, the operation of the new converter is explained and analyzed, a design procedure is presented and demonstrated with an example, and experimental results that confirm the feasibility of the converter are also presented. [ABSTRACT FROM AUTHOR]

This paper focuses on the common dc-link voltage between a three-phase diode rectifier and a modular multilevel cascade inverter based on double-star chopper cells (MMCI-DSCC) for a medium-voltage motor drive. This motor drive can be operated even when no capacitor exists on the dc link. However, a nonnegligible, but predictable, amount of switching-ripple voltage occurs on the dc link. This paper achieves modeling and analysis of the switching-ripple voltage, thus making it possible to design a small-sized dc passive filter consisting of series connection of a film capacitor and a damping resistor. A 400-V, 15-kW down scaled system is used to confirm the effectiveness of the analysis and the dc filter. Experimental results show that the switching-ripple voltage can be attenuated satisfactorily by the dc filter, and that the power loss dissipated in the damping resistor is negligible, compared to the rated power of 15 kW. [ABSTRACT FROM AUTHOR]

This paper proposes a pulse-width modulation three-level converter with reduced filter size using two transformers. The proposed converter has many advantages. All switches sustain only the half of the input voltage and since the secondary rectified voltage is a three-level waveform, the output filter inductor can be reduced. Also, because of the power sharing of transformer and reduced output inductor, high efficiency can be obtained. The operational principle, analysis, and design considerations of the proposed converter are presented in this paper. The validity of this study is confirmed by the experimental results from a prototype with 600 W, 500-600 V input, and 60 V output. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

This paper presents a single-inductor multiple-output (SIMO) LED driver with precise dimming and full dimming range. Based on the coordination of a string-level scheme and a system-level dimming scheme, the proposed SIMO LED driver can overcome practical constraints of existing SIMO LED drivers such as limited dimming range and needs for high-current switches. The proposal can achieve dimming precision up to an accuracy of 0.8% and also full dimming range. It has the flexibility of using either phase-shift or synchronous pulsewidth-modulated (PWM) switching for dimming control. The proposed circuit and control operations have been practically verified with a 25-W off-line SIMO-driven LED system. Practical evaluations of its power quality and energy efficiency are also provided. [ABSTRACT FROM AUTHOR]

A simple scheme to realize phase-disposition carrier pulse width modulation (PD PWM) for parallel two-level voltage-source converters (2L-VSCs) is presented in this paper. The proposed implementation only uses a single carrier signal and can easily be implemented using a digital signal processor. The operation of the parallel VSCs with the coupled inductor (CI) under the PD PWM is briefly discussed, and the associated dc flux injection problem is investigated. A CI saturation issue during the band transition under the PD PWM scheme is also explored, and the strategy to avoid this problem is presented. In addition, the proposed strategy also maintains a volt–second balance to synthesize desired reference space voltage vector during the band transition. As a result, a smooth transition from one modulation band to the other is ensured without causing disturbances in the line-to-line voltage. The switching losses and the harmonic performance of the proposed implementation are also compared with the commonly used phase-shifted carrier pulse width modulation. The implementation issues are discussed and the experimental results are also presented. [ABSTRACT FROM AUTHOR]

Primary-side controlled universal-line flyback converters have been widely used in low-power applications due to their simplicity, low standby power, and low cost. However, conventional OCP schemes normally cause too large a variation in output current when the input voltage varies. This paper proposes a self-compensating OCP circuit to achieve a high-precision constant current at different input voltages which can be used in flyback converters working in discontinues conduction mode. It consists of a CS S/H circuit and a dynamic OCP voltage reference circuit. Compared with conventional OCP circuits, it does not need an extra compensation circuit. To verify the feasibility and performance of the proposed circuit, an IC controller that uses the proposed OCP circuit has been designed and fabricated in 0.35 μm 5-V/40-V high-voltage CMOS technology. Experimental results show that the constant output current precision of the prototype is within ±1% when the input line voltage changes from 85 to 265 Vac. In the common line voltage range (\rm110-220\ Vac ), the output current regulation accuracy can reach a level as high as ± 0.3%. [ABSTRACT FROM AUTHOR]

A nonlinear pulse width modulation-controlled single-phase boost mode photovoltaic grid-connected inverter with limited storage inductance current is proposed in this paper. The circuit topology, control strategy, steady-state principle characteristic, and design criterion for the key circuit parameters of this kind of inverter are investigated in depth, and important conclusions are obtained. The inverter's regenerating energy duty ratio 1–D which decreases with the decline of the grid-connected voltage is real time adapted by sampling and feeding back the inverting bridge modulation current, and the average value of the modulation current in each switching cycle tracks the reference sinusoidal signal to get high-quality grid-connected current. The active control of the energy storage inductance current and the balance of the voltage step-up ratio are realized by adding a bypass switch connected in parallel with the energy storage inductance and using two kinds of switching pattern namely boost pattern and freewheeling pattern. The theoretical analysis and experimental results of the 1 kVA 110 VDC/220 V50 Hz photovoltaic grid-connected inverter prototype show that it has the advantages such as single-stage boost conversion, high conversion efficiency, high quality of grid-connected current waveform, low value of energy storage inductance, simple control, etc. [ABSTRACT FROM AUTHOR]

Multiple output converters (MOCs) are widely applied to applications requiring various levels of output voltages due to their advantages in terms of cost, volume, and efficiency. However, most of the conventional MOCs cannot regulate multiple outputs tightly and they can barely avoid the cross-regulation problem. In this paper, the recently developed time-division multiple control (TDMC) method, which can regulate all of the outputs with a high accuracy, is used for a multiple output battery charger based on the phase-shift full-bridge topology to simultaneously charge three batteries. The proposed charger is able to charge three different kinds of batteries or three of the same kind of battery in different state of charges (SOCs) independently and accurately with the constant current/constant voltage (CC/CV) charge method. As a result, the strict ripple specification of a battery can be satisfied for multiple battery charges without difficulty. In addition, the proposed charger exhibits a high efficiency since the soft switching of all of the switches during the entire charge process can be guaranteed. The operating principle of the converter and the design of the controller, including the state-space average modeling, will be detailed, and the validity of the proposed method is verified through experiments. [ABSTRACT FROM PUBLISHER]

This paper presents the design, modeling, and control of an isolated dc-dc three-port converter (TPC) based on an interleaved-boost full-bridge converter with pulsewidth modulation (PWM) and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven by phase-shifted PWM signals, where both phase angle and duty cycle are the controlled variables. The power flow between the two inputs is controlled through the duty cycle, whereas the output voltage can be regulated effectively through the phase shift. The primary-side MOSFETs can achieve zero-voltage-switching (ZVS) operation without additional circuitry. Additionally, due to the ac output inductor, the secondary-side diodes can operate under zero-current-switching (ZCS) conditions. In this study, the operation principles of the converter are analyzed and the critical design considerations are discussed. The dynamic behavior of the proposed ac-inductor-based TPC is investigated by performing state-space modeling. Moreover, the derived mathematical models are validated by simulation and measurements. In order to verify the validity of the theoretical analysis, design, and power decoupling control scheme, a prototype is constructed and tested under the various modes, depending on the availability of the renewable energy source and the load consumption. The experimental results show that the two decoupled control variables achieve effective regulation of the power flow among the three ports. [ABSTRACT FROM PUBLISHER]

For high-power applications, paralleling converters is a popular approach to increase the power capacity of the system. Circulating current has been a major concern for the implementation of paralleled converters. This paper proposes a three-level space vector modulation (SVM) scheme for a system with two paralleled voltage-source converters (VSCs) with common-mode inductor (CMI) or single-phase inductors. The proposed scheme aims to reduce the zero-sequence circulating current (ZSCC) and the magnitude of common-mode voltage (CMV) of the system simultaneously. The ZSCC patterns with respect to modulation schemes are first analyzed to provide a clear understanding of the generation of ZSCC. Based on the analysis, the proposed three-level modulation scheme is introduced. Furthermore, performance regarding the ZSCC peak value, impact on the common-mode current (CMC), CMI scaling analysis, and switching losses are analyzed and compared with the existing methods. The proposed method has been verified in both simulation and experiment. [ABSTRACT FROM AUTHOR]

The switching cell (SC) direct pulse width modulation ac–ac converters have several advantages; in particular, they do not experience commutation issues, are not susceptible to reverse-recovery losses of body diode of switching devices, produce output waveforms of good quality, are more immune to EMI noise, and have smaller input/output current ripples. The magnetic components of the SC ac–ac converters consist of coupled inductors and a filter inductor. This paper proposes an integrated inductor which integrates all magnetic components of the SC ac–ac converters into one magnetic assembly. The leakage inductance of the proposed integrated inductor is utilized to eliminate the filter inductor in buck, boost, and buck—boost-type SC ac–ac converters. The proposed integrated inductor improves the power density and reduces cost and losses because it requires fewer magnetic cores, coils, and soldering connections. The proposed integrated inductor is especially suitable for high-current applications because it can avoid the magnetic core saturation caused by current, and can eliminate the air gap in the core. The proposed integrated inductor can realize high leakage inductance; therefore, the input and output current ripples can be reduced significantly. To verify the proposed integrated inductor, a 2.3-kW prototype inductor was built and tested. [ABSTRACT FROM AUTHOR]

This paper presents an average current mode buck dimmable light-emitting diode (LED) driver for large-scale single-string LED backlighting applications. The proposed integrated current control technique can provide exact current control signals by using an autozeroed integrator to enhance the accuracy of the average current of LEDs while driving a large number of LEDs. Adoption of discontinuous low-side current sensing leads to power loss reduction. Adoption of a fast-settling technique allows the LED driver to enter into the steady state within three switching cycles after the dimming signal is triggered. Implemented in a 0.35-μm HV CMOS process, the proposed LED driver achieves 1.7% LED current error and 98.16% peak efficiency over an input voltage range of 110 to 200 V while driving 30 to 50 LEDs. [ABSTRACT FROM AUTHOR]

This paper proposes single-phase direct pulsewidth modulation (PWM) buck-, boost-, and buck–boost-type ac–ac converters. The proposed converters are implemented with a series-connected freewheeling diode and MOSFET pair, which allows to minimize the switching and conduction losses of the semiconductor devices and resolves the reverse-recovery problem of body diode of MOSFET. The proposed converters are highly reliable because they can solve the shoot-through and dead-time problems of traditional ac–ac converters without voltage/current sensing module, lossy resistor–capacitor (RC) snubbers, or bulky coupled inductors. In addition, they can achieve high obtainable voltage gain and also produce output voltage waveforms of good quality because they do not use lossy snubbers. Unlike the recently developed switching cell (SC) ac–ac converters, the proposed ac–ac converters have no circulating current and do not require bulky coupled inductors; therefore, the total losses, current stresses, and magnetic volume are reduced and efficiency is improved. Detailed analysis and experimental results are provided to validate the novelty and merit of the proposed converters. [ABSTRACT FROM AUTHOR]

A family of isolated buck–boost dc/dc converter for wide input-voltage range is proposed in this paper, and the full-bridge (FB) boost converter, being one of the typical topologies, is analyzed. Due to the existence of the resonant inductor (including the leakage inductor), the FB-boost converter can only adopt the two-edge-modulation (TEM) scheme with the FB cell being leading-edge modulated and the boost cell being trailing-edge modulated to minimize the inductor current ripple over the input-voltage range, and a phase-shift-control-scheme-based TEM with the use of the market available controller IC such as UC3895 is proposed, which realizes phase-shifted control for the FB cell to achieve zero-voltage switching. In order to improve the reliability and efficiency of the FB-boost converter, a three-mode dual-frequency control scheme is proposed, in which the FB-boost converter operates in boost, FB-boost and FB modes in low, medium and high input voltage regions, respectively, and for which the expression of the inductor current ripple is derived in this paper. As the input voltage in the FB-boost mode is close to the output voltage, the inductor current ripple in this mode is much smaller than that in the other modes, and the switching frequency of the boost cell in this mode can be lowered to one-(2N+1)th of the preset switching frequency to reduce the switching loss, and hence, to improve the efficiency. A 250–500 V input, 360 V output, and 6 kW rated power prototype is fabricated to verify the effectiveness of the design and control method. The average efficiency over the input-voltage range is 96.5%, and the highest efficiency attained is 97.2%. [ABSTRACT FROM AUTHOR]

This paper presents a single-phase power factor corrector based on a tapped-inductor buck–boost converter. This paper suggests simplified models of the power stage under current-mode control and derives small-signal transfer functions of both the current and voltage control loops. Design rules for implementation of the proposed power factor corrector (PFC) are also suggested. The proposed PFC features low dc bus voltage, arbitrary lower than the peak line voltage. The proposed PFC is suitable for applications in computers and communications, where dc isolation can be provided by the downstream dc/dc converters. Simulation and experimental results are also reported and stand in good agreement with theoretical expectations. [ABSTRACT FROM AUTHOR]

A new zero-voltage-switched bidirectional dc–dc converter with coupled inductors is proposed in the paper. The proposed converter can operate with a steep conversion ratio, soft switching, a continuous inductor current, and fixed switching frequency. It can also operate with the switch stresses of a conventional pulsewidth-modulation-tapped/coupled-inductor converter regardless of the direction of power flow and without any voltage spikes across the switches during turn-OFF. These features are due to a very simple auxiliary circuit that is operational regardless of the direction of power flow and absorbs energy from the leakage inductance of the coupled inductors during switch turn-OFF. In the paper, the operation and design of the converter are discussed and its feasibility is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a new type of ac–ac converter which can operate as traditional noninverting buck and boost converters, and inverting buck–boost converter as well. The proposed converter uses six unidirectional current flowing and bidirectional voltage blocking switches, implemented by six reverse blocking insulated-gate bipolar transistors (IGBTs) or series mosfet–diode pairs, two input and output filter capacitors, and one inductor. It has no shoot-through problem of voltage source (or capacitor) even when all switches are turned-on, and therefore, pulsewidth modulation dead-times are not needed resulting in high-quality waveforms, and solves the commutation problem without using bulky and lossy RC snubbers or dedicated soft-commutation strategies. It has smaller switching losses because only two switches out of six are switched at high frequency during each half-cycle of input voltage, and it can use power MOSFETs as body diode never conducts, making it immune from mosfet failure risk which otherwise may occur due to poor reverse recovery problem of body diode. The noninverting buck–boost mode of the proposed converter can be used in applications with both step-up and step-down demand, while the inverting buck–boost mode can also be used in its application as dynamic voltage restorer. Detailed analysis of the proposed converter is given, and experimental results are also provided. [ABSTRACT FROM AUTHOR]