Search

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

In order to increase the efficiency of modern microprocessor power supplies used in data centers, 380-V dc power distribution systems have been attracting attention due to their high efficiency and high reliability. This paper presents an innovative single-stage approach for 380-V voltage regulator modules (VRMs) based on a quasi-resonant multilevel topology constant on-time operation. The proposed topology inherently integrates the multiphase approach, providing fast phase shedding and flat high-efficiency curves even at light-load conditions. This is a unique advantage, which is not possible to establish in the two-stage approach, which is very important in server architectures, and where high efficiency is required even at light-load conditions. This paper analyzes the circuit topology and proposes a control architecture for fast transient response, including current-sharing capabilities. The digital controller has been implemented in 0.16- $\mu$ m lithography together with a digital pulsewidth modulation with a 195-ps resolution and a 40-MS/s 7-bit analog-to-digital converter. Experimental results show an efficiency of 93% for a 120-A 380–1.8-V VRM power supply. [ABSTRACT FROM AUTHOR]

This paper proposes a fifth-order resonant immittance network based dual-active-bridge (DAB) converter and an optimal modulation method that will ensure high-efficiency operation of the converter under wide-range variations in voltage ratio and output power level. The proposed modulation method is based on the concept of total power loss minimization, where a loss model is developed and an optimization algorithm is formulated to compute the optimal set of internal and external phase shift parameters that will lead to the maximum efficiency for a given set of operating parameters including voltage ratio and output power level. It is found that to maintain high-efficiency operation under wide-range variations in voltage ratio and output power level, the DAB converter is required to switch between different operation modes and neither soft-switching operation nor unity-power-factor operation is able to achieve wide-range high efficiency performance when used alone. The importance of $reconfigurability$ of operation mode for achieving wide-range high efficiency performance is clearly illustrated in this paper. [ABSTRACT FROM AUTHOR]

The emergence of applications which require high-voltage switches has created a tendency to use semiconductor device series stacks. These series stacks permit operation at blocking voltages above semiconductor elements’ nominal voltage. Insulated-gate bipolar transistors (IGBT) are currently utilized for controllability and switching speed, when these topologies are employed. The main challenge therewith is guaranteeing voltage balance between IGBTs, both when blocked and when switching transistors. Most of the methods which have been proposed to mitigate static and dynamic voltage unbalances increase transistor losses. The series stack loss-less high voltage switch (LHVS) which mitigates voltage unbalances, thus reducing switching losses, is presented in this paper. LHVS consists of a circuit, which ensures soft IGBT switching, an energy recovery circuit, and a gate delay compensation circuit. Additionally, the insulation voltage level is guaranteed to be equal between control circuit and high-voltage side of each IGBT. The operating principle of the LHVS is detailed in this paper, as is experimental validation which has been performed for three series stack modules. Static unbalances are reduced to 1%, while the differences between collector–emitter voltage curves in switching “on” do not surpass 8 ns, and switching losses are reduced by 41%, as compared to the hard-switching topology. [ABSTRACT FROM AUTHOR]

Fault tolerance in wind turbines is considered crucial to increase their reliability and availability levels. This paper presents a fault-tolerant direct-drive permanent magnet synchronous generator (PMSG) using new direct control techniques, with the ability to handle power semiconductor open-circuit faults in the full-scale back-to-back converter. The fault-tolerant topology consists of a five-leg converter, with a shared leg connected to a generator phase and to its corresponding grid phase, through a triode for alternating current (TRIAC). The main contribution of this paper consists of the development of an alternative direct torque control and direct power control schemes for both machine-side converter and grid-side converter, respectively. Moreover, a reliable fault diagnostics algorithm without requiring additional sensors is also integrated, providing the information required to instantaneously trigger fault-tolerant remedial strategies. Simulation and experimental results are presented to validate the effectiveness of the proposed fault-tolerant PMSG drive. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are being used in wide range of power electronic applications. These converters have attracted a lot of attention during recent years and exist in different topologies with similar basic concepts. This paper presents five main submodules (SMs) to be used as the basic structures of MLIs. The paper reviews the common MLI topologies from the structural point of view. The topologies are divided into the different SMs to show conventional MLI configurations and future topologies that can be created from the main SMs. A comparative study between different topologies is performed in detail. The MLIs are categorized and investigated with from different perspectives such as the number of components, the ability to create inherent negative voltage, working in regeneration mode and using single dc source. [ABSTRACT FROM AUTHOR]

This paper presents a balancing algorithm for the so-called Director Switch, a controlled, reverse conducting, self-powered, high-voltage switch, using series-connected insulated gate bipolar transistors (IGBTs). This is a key component on two new voltage-source, high-voltage direct current (HVDC) converter topologies. These, which promise efficiency, cost, and size reductions, are an alternate arm converter and a series bridge converter. One of the main design challenges of the director switch is how to supply the IGBT gate drivers, and other auxiliary electronics while overcoming the high-voltage insulation barrier to ground level. In this paper, this is achieved by using the energy stored in a capacitive clamp snubber circuit, which also helps with the overvoltage mitigation during rare hard-switching events. However, the clamp capacitor and by proxy the IGBT voltages become highly unbalanced during operation, compromising the integrity of the switch. This paper presents a balancing strategy that consists in applying a controlled delay in the switching of the IGBT levels, in a way that forces a voltage balance on all the switch levels. The paper explains the unbalance. Then, the balancing strategy is explained and validated on simulation and on a high-voltage experimental rig, on switches comprising two and three series-connected IGBTs, respectively. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

Isolated, zero-voltage-switching dc–dc converter topologies represent attractive solutions in the continuous run toward higher switching frequencies, allowing more compact power supplies. Among them, the asymmetrical half-bridge flyback converter represents an interesting option, featuring simple duty-cycle control at constant switching frequency, as opposed to the popular LLC converter. The majority of papers dealing with this topology consider an approximated voltage gain similar to that of an isolated buck converter operating in continuous conduction mode, i.e., proportional to the duty cycle and, practically, load independent. On the contrary, the true voltage gain is nonmonotonic at high duty-cycle values. Anytime the converter is designed for a resonant operation, as is advisable to eliminate any reverse recovery problem of the rectifier diode, the voltage gain not only increases, but also becomes a function of the switching frequency. This article investigates the converter's voltage gain in detail, deriving a theoretical framework capable of capturing its real behavior and dependencies. The proposed analytical model has been verified through simulations as well as experimental measurements taken on a 160-W prototype working at 400 kHz. [ABSTRACT FROM AUTHOR]

This paper studies the driving of white light emitting diodes (LEDs) from very low voltages in the 1.2 to 2 V range. The proposed idea is based on replacing the standard Schottky diode used in conventional converter topologies (i.e., buck, buck–boost, and boost) with an LED while shortcutting the output of the converter. In this configuration, the LED works both as the load and the rectifier diode of the converter, hence switching the LED at high frequencies (>100 kHz). Moreover, a thorough analytical study is carried out for the two topologies proposed in this paper, emphasizing in particular their static analysis and the obtaining of the boundaries between the different conduction modes. Finally, the idea is experimentally validated by means of the boost converter variation (i.e., the DL//S ac-LED driver). The DL//S ac-LED driver was also compared with a dc–dc boost converter, showing a better luminous efficacy while disposing of the Schottky diode and the output capacitor. The analysis was carried out when connected to a Li-ion battery using a simple control and integrated circuit for its development. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dc power electronic transformer (DCPET) topology for locomotive, ac/dc hybrid grid, dc distribution grid, and other isolated medium-voltage and high-power applications. Compared with conventional PET topology, the proposed DCPET has fewer power semiconductor devices and high-frequency isolation transformers, which can improve the power density and reliability. Fault handling or redundancy design can be achieved to further improve the reliability when some dc–dc modules break down. Also, input voltage sharing control can be omitted to simplify the control system and improve the stability. Meanwhile, soft switching is guaranteed for all the switches, which is beneficial to increase switching frequency and improve power density. In this paper, the principle, evolution, and control of the proposed DCPET are respectively presented and studied in detail. Finally, a prototype of the proposed DCPET is built and the experimental results verify the validity and superiority of the proposed topology. [ABSTRACT FROM AUTHOR]

Enhancement of dc bus voltage utilization for a five-level inverter with single dc source and capacitor-fed H-bridge (CHB) units is investigated in this paper. A carrier-based modulation technique is used for boosting the dc bus utilization, which is established by providing detailed mathematical analysis. The five-level inverter used here is realized by cascading a CHB unit to each phase of a three-level neutral point clamped inverter. The increase in dc bus voltage utilization owes to the pole voltage redundancies offered by CHB units. The floating capacitors of H-bridge units are balanced within a quarter fundamental cycle using the switching state redundancies of pole voltage levels. The aforementioned modulation technique allows the inverter to enhance the dc bus utilization from 0.577 $\text{V}_{\text{dc}}$ to 0.63 $\text{V}_{\text{dc}}$ under unity power factor. This enhancement is obtained in the linear modulation range without increasing the dc bus voltage, and thus, the inverter can operate without the presence of low-order harmonics in its phase voltages. The strength of this paper lies in its detailed mathematical analysis for finding out the limiting modulation index and power factor condition in the light of floating capacitor voltage balancing issue. Simulation as well as experimental verification of the modulation scheme is carried out on an induction motor drive under various operating conditions. It is shown that this carrier-based modulation technique is suitable for any single source inverter topology with one CHB unit per phase. [ABSTRACT FROM AUTHOR]

This paper presents a new six-level flying capacitor based (FC-based) multilevel converter with one dc source and the capability of operating in all power factors and modulation indexes. Multilevel converters with one dc voltage source are attractive in many applications as they do not need rather expensive and bulky multiwinding input transformer connection at the dc side. On the other hand, not all classic multilevel converters with one dc source can produce any desirable number of output voltage levels at all power factors and/or modulation indexes. In this paper, a hybrid structure is proposed in which six voltage levels can be realized at the ac terminals. The modulation technique and the control strategy for the FC voltage balancing are presented. To show the advantages of the proposed converter, different performance criteria, such as switch count and rating, the size of capacitors, switching frequency, and power losses, are compared with other existing six-level topologies. The results indicate that the proposed structure is superior to other six-level converters from different standpoints. Simulation results are used to further evaluate the performance of the proposed converter. A laboratory-type experimental setup is used to validate the theoretical results. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper proposes a novel method for instantaneous balancing of neutral-point (NP) voltages with stacked multilevel inverters (MLIs) for variable-speed drives. The stacked MLI uses series-connected dc sources and NPs (connecting points of dc sources) to obtain the desired levels. The balancing of NP voltages are obtained by using a low-voltage-capacitor-fed cascaded H-bridge (CHB) per phase of a symmetrical six-phase induction machine (IM), which ensures zero current drawn from NPs (at any given instant). Since no current is drawn from NPs, the single dc-link operation with stacked capacitors is also possible. The scheme is suitable for applications, where low-voltage dc sources and batteries are stacked to form a dc link. A variable-speed operation is done using a seven-level inverter scheme for a symmetrical six-phase IM, which is formed by three dc-link stacked capacitors cascaded with two low-voltage-capacitor-fed CHBs per phase. Furthermore, the method is extended for an open-end IM to obtain a seven-level common-mode eliminated space vector structure using a single dc link. The generalization of this method for any stacked $n$ -level inverter without NP voltage deviation is also presented in this paper. The experimental results and analysis are included to validate the proposed method. [ABSTRACT FROM AUTHOR]

Nonregenerative pulsewidth-modulated (PWM) rectifiers are increasingly being considered for applications, where the power flow is unidirectional, such as power supplies for telecommunications, X-ray, the machine-side converter for wind energy conversion systems, etc. They use fewer active switches, which increase their power density and reduce cost. This paper proposes a novel reduced switch topology for a multilevel (five-level or higher) nonregenerative PWM rectifier. It uses only four controlled switches and eight diodes per phase for a five-level rectifier. Half of the diodes are naturally commutated (zero current switching) at the line frequency, which reduces switching losses. This topology has several other advantages compared to similar topologies reported in the literature, such as minimum voltage stress across the devices, elimination of transient voltage-balancing snubbers, no extra hardware for balancing the flying capacitors, the dc-link mid-point voltage, etc. In this paper, switching cycle average modeling and the carrier-based modulation strategy for this rectifier are also presented to maintain a balanced dc link and to regulate flying capacitor voltages, while achieving unity displacement factor at the rectifier input terminals. The overall performance of the rectifier is verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage soft-switched high-frequency-link three-phase dc–ac converter topology. The topology supports unidirectional dc to ac power flow and is targeted for applications like grid integration of photovoltaic sources, fuel cell, etc. The high frequency magnetic isolation results in reduction of system volume, weight, and cost. Sine-wave pulsewidth modulation is implemented in dc-side converter. Though high-frequency switched, dc-side converter is soft switched for most part of the line cycle. The ac-side converter active switches are line frequency switched incurring negligible switching loss. The line frequency switching of ac-side converter facilitates use of high voltage blocking inherently slow semiconductor devices to generate high voltage ac output. In addition, a cascaded multilevel structure is presented in this paper for direct medium-voltage ac grid integration. A detailed circuit analysis considering nonidealities like transformer leakage and switch capacitances, is presented in this paper. A 6-kW three-phase laboratory prototype is built. The presented simulation and experimental results verify the operation of the proposed topologies. [ABSTRACT FROM AUTHOR]

Three-level neutral-point clamped voltage source converter (3L-NPC-VSC) is widely used in high-power and medium-voltage (MV) applications and the most used multilevel VSC topology. 3L-Active-NPC-VSC (3L-ANPC-VSC) was introduced to overcome the unequal losses distribution as main structural drawback of the 3L-NPC-VSC. During the switching event of semiconductor devices, the stray inductance takes a special role in the commutation path of the switching current. Mutual coupling inductance between the components participating in the commutation path has to be considered for a theoretical assessment of the total stray inductance of each commutation path. Besides, the measurement of the commutation path stray inductance has to be carried out during the turn-on of the semiconductor device, instead of during the turn-off, to consider the reverse blocking voltage of the opposite switching semiconductor device. This paper shows how a dual 3L-ANPC-VSC phase-leg has been carefully designed and assembled to build a ±10 MVAr five-level VSC for MV-static synchronous compensator applications. The minimization of the stray inductance, the equalization of the total switching power losses for all commutation paths and power density maximization with snubberless operation are within the main technical design requisites. On the basis of the theoretical analysis, the stray inductance of all the commutation paths has been extracted, considering mutual coupling effect, by means of three-dimensional finite-element-analysis simulations. Once the design concept is theoretically validated, the estimated values have been compared with the experimental results obtained from the performance of double-pulse tests for each commutation path. This paper presents, for the first time, all the analysis details of the 3L-ANPC-VSC commutation behavior using 4.5-kV and 1.5-kA trench high-voltage insulated-gate bipolar transistor modules. [ABSTRACT FROM AUTHOR]

This paper presents the digital implementation of a boundary controller with unipolar switching characteristic for single-phase voltage source full-bridge inverters. This paper expands the application of a second-order switching surface-based control method to unipolar switching of single-phase voltage source inverters (VSIs) using a finite-state machine. The finite-state machine has been formulated considering four different states of the inverter; positive,zero1, negative, andzero2. The second-order boundary control governs the current state of the system and provides proper switching action to keep the system within the desired reference. The control law is implemented digitally in F28m35x digital control card. A full-bridge inverter topology is used to achieve the three-level voltage switching. Various simulations and experiments were performed in a 550 VA, 120 V, 60 Hz VSI with a digitally implemented controller to verify the theoretical predictions. A high-quality voltage output was obtained for various loading conditions. The transient performance of the controller was investigated using a reference and load changes. A comparison of the implementation was made with the existing classical controllers to verify the fast-dynamic response of the system. [ABSTRACT FROM AUTHOR]

Most of the two-stage converters for electric bike battery charging comprise of a boost converter for power factor correction (PFC) followed by a dc–dc converter with universal input voltage. These two-stage conversions suffer from poor efficiency and increased component count. In this paper, a single-stage switched inductor Cuk converter based PFC converter is proposed, which offers high step-down gain, low current stress, high efficiency, and reduced component count. The operational analysis and design equations for various components of the proposed converter are carried out in continuous current mode. This paper presents mathematical modeling, analysis, simulation, and experimentation on the proposed converter rated for 500 W, 48 V/10.4 A. The performance investigation of the proposed converter with respect to power quality indices like voltage total harmonic distortion (THD), current THD, and total power factor is carried out with various types of loads such as resistive load and battery load in both constant voltage (CV) and constant current (CC) mode. Furthermore, the dynamic performance of the proposed converter with battery charging is investigated in CV mode and CC mode with respect to the wide range of supply variations. [ABSTRACT FROM AUTHOR]

Dual active bridge (DAB) based converters offer the benefit of smaller volume due to high-frequency isolation and controllability of active power flow, making them attractive for various applications, such as renewable energy generation, plug-in hybrid vehicles, and distribution systems. This paper presents a novel converter topology along with a modulation strategy for a DAB-based three-phase ac to dc converter. The major benefits are single-stage conversion, no unreliable intermediate dc-link capacitor, reduced number of switches, i.e., only two active switches on the ac side, simple control scheme, open-loop unity power factor operation, bidirectional power flow, and partial soft-switching. This paper presents the analysis of all the operating modes of the converter, resulting in the analytical estimation of power transfer and rms winding current and investigation of soft-switching conditions for the power devices. Simulation and experimental results have been presented to demonstrate the advantages of the proposed technique and accuracy of the analysis.1 [ABSTRACT FROM AUTHOR]

This paper presents a unified framework for the modeling, analysis, and design of load-independent Class E and Class EF inverters and rectifiers. These circuits are able to maintain zero-voltage switching and, hence, high efficiency for a wide load range without requiring tuning or use of a feedback loop, and to simultaneously achieve a constant amplitude ac voltage or current in inversion and a constant dc output voltage or current in rectification. As switching frequencies are gradually stepping into the megahertz (MHz) region with the use of wide-bandgap (WBG) devices such as GaN and SiC, switching loss, implementing fast control loops, and current sensing become a challenge, which load-independent operation is able to address, thus allowing exploitation of the high-frequency capability of WBG devices. The traditional Class E and EF topologies are first presented, and the conditions for load-independent operation are derived mathematically; then, a thorough analytical characterization of the circuit performance is carried out in terms of voltage and current stresses and the power-output capability. From this, design contours and tables are presented to enable the rapid implementation of these converters given particular power and load requirements. Three different design examples are used to showcase the capability of these converters in typical MHz power conversion applications using the design equations and methods presented in this paper. The design examples are chosen toward enabling efficient and high-power-density MHz converters for wireless power transfer (WPT) applications and dc/dc conversion. Specifically, a 150-W 13.56-MHz Class EF inverter for WPT, a 150-W 10-MHz miniature Class E boost converter, and a lightweight wirelessly powered drone using a 20-W 13.56-MHz Class E synchronous rectifier have been designed and are presented here. [ABSTRACT FROM AUTHOR]

This paper proposes generation of a 15-level (14 concentric) dodecagonal voltage space vector structure (DVSVS) for a star connected induction motor drive. The proposed multilevel DVSVS is obtained by cascading two inverters, namely a primary and secondary inverter. The primary inverter is a five-level (5L) structure formed by stacking two three-level flying capacitors with individual reduced dc sources and the secondary inverter is also a 5L structure formed by cascading two capacitor-fed cascaded H-bridges (CHB). The active power is supplied by the primary inverter, while the secondary inverter acts as switched capacitor harmonics filter, and capacitors in the secondary inverter are balanced naturally irrespective of load power factor for entire modulation index. The high-voltage dc supply fed primary inverter is operated in quasi-square wave mode, while the high frequency switching is applied to low voltage CHBs, thus, reducing the overall switching loss. The proposed scheme gives the advantages of both DVSVS and multilevel structure, thus, making it one of the solutions for battery or stacked dc-fed applications. The paper also presents the experimental results as well as comparison study with the existing topologies to support the advantages of proposed scheme. [ABSTRACT FROM AUTHOR]

High-performance cloud computing enables many key future technologies such as artificial intelligence (AI), self-driving vehicle, big data analysis, and the Internet of things (IoT), using clustered CPU and GPU servers in the datacenter. To improve the power efficiency and the infrastructure flexibility, the computing industry is adopting 54 VDC to power the servers in the open compute racks. In this paper, a new modeling technique for a soft-switched dc–dc converter is presented and suitable to guide optimal design in different applications, for example, 54 V to point of load (PoL) for the new open compute rack. To improve the model accuracy and reduce the complexity, this paper proposes a reduced-order linear differential equation (LDE) based modeling technique to discover the following: 1) the tank resonance involving the output inductor; 2) the output current ripple and its impact on power efficiency; 3) the proper on-time control for soft switching; 4) the unique bleeding mode under the heavy load; 5) the output power capability of the converter; and 6) component tolerance analysis and impact on the performance of the converter. With the power loss estimation, design guidelines are provided for a reference design and design improvement based on this new modeling technique. Using the proposed method, great accuracy can be expected in the efficiency estimation. Simulation and experimental results are provided to verify the modeling technique in a 54–1.2 V 25 A dc–dc converter prototype. [ABSTRACT FROM PUBLISHER]

Fast-switching power converters are a key enabling technology for the more electric aircraft (MEA), but the generated electromagnetic interference (EMI) poses significant challenges to the electrification effort. To meet the stringent aerospace EMI standards, passive filters are commonly employed, despite the weight and size constraints imposed by the MEA. Alternatively, the EMI source, i.e., the high dv\text/ dt and di\text/ dt slew rates, can be addressed through waveform-shaping techniques. For example, while most soft-switching converters can reduce switching loss, they do so by switching the semiconductor devices in a slower and smoother manner, resulting in the attenuation of high-frequency harmonics. This paper examines the auxiliary commutated pole inverter (ACPI) topology, and its first contribution is the attenuation of the high-frequency content of its EMI source, that is, the output voltage, in a predictable manner, through the active control of the resonant circuit. This is achieved by first, discussing the time-domain characteristics of trapezoidal and S-shaped pulse-trains that lead to attenuated high-frequency harmonic content, and second, by analyzing the equivalent LC circuit of the ACPI. The design of the inverter is then focused on the active control of the resonant parameters, for a predetermined and enhanced output voltage high-frequency response. The second contribution of this paper is the comparison of the EMI performance of hard switching and of three soft-switching modes, fixed-timing control, variable-timing control, and capacitive turn-offs, and how this informs important metrics such as power efficiency, current stress, and implementation complexity. Finally, the third contribution is on the trade-offs that arise when the primary design goal is enhanced EMI performance as opposed to switching loss reduction. A 5-kW, 3-phase ACPI prototype is used for validating the high-frequency content attenuation at source. It is shown that the ACPI can achieve a 37 dB harmonic attenuation of its output voltage at 4 MHz, compared to a hard-switched inverter. [ABSTRACT FROM AUTHOR]

To support the development of high-frequency ac microgrids in terms of compact design, high-voltage gain and low total harmonic distortion (THD), a buck–boost dual-leg-integrated step-up inverter is proposed in this paper. The inverter is formed by integrating a buck–boost converter into a conventional single-phase full-bridge inverter by sharing the upper switch and the body diode of the lower switch in both bridge-legs. Consequently, the component count is significantly reduced over the step-up inverter counterparts. In addition, to address the drawbacks of hybrid modulation methods adopted by existing dual-leg-integrated inverters, such as double-variable control, and high THD of output voltage/current at high input voltage and heavy load conditions, unipolar frequency doubling sinusoidal pulse width modulation scheme is adopted in this inverter. As a result, the modulation ratio M becomes the only control variable to regulate the output voltage/current and the control is simplified. The THD of the proposed inverter output can remain low throughout the entire input voltage range and load power range. This paper presents the topology derivation procedure, operation principle, and steady-state characteristics of the proposed inverter. To validate the effectiveness of theory, experimental results of a 400 W hardware prototype, where the output voltage frequency is at 500 Hz, are reported. [ABSTRACT FROM PUBLISHER]

In order to increase the efficiency of modern microprocessors power supplies used in data centers, the 48-V dc distribution bus is gaining growing attention. For such applications, voltage regulation modules (VRMs) are currently obtained using two-stage conversion systems with an intermediate 12-V dc bus. This paper presents an innovative single-stage approach for the 48-V VRM based on a quasi-resonant constant on-time (COT) operation. The proposed topology inherently integrates the multiphase approach, providing fast phase shedding and flat high-efficiency curves even at light load conditions. This is a unique advantage, usually not available in the two-stage approach, that is very important in server architectures, where high efficiency is required even at light load conditions. The paper analyses the circuit topology, and proposes a control architecture for fast transient response, including the current sharing capabilities, and a solution for implementing the integrated magnetics. The digital controller has been implemented in 0.16-$\mu$ m lithography together with a digital pulse-width-modulation with a 195 ps resolution, and a 40 MS/s, 7-bit ADC. Experimental results show an efficiency of 93.1% for a 250 A, 1.8 V VRM, and of 93.2% for a 102 A, 1.2-V double data rate (DDR) power supply. [ABSTRACT FROM PUBLISHER]

This paper presents the tradeoff study of heat sink and output filter volume of a GaN HEMT based single-phase inverter. The selected topology is three-level active neutral point clamped (ANPC) inverter, and the main aim is to explore the benefits of the GaN HEMTs at 600 V blocking class on the system level efficiency, and power density under the wide range of operating conditions. The paper starts by introducing the inverter topology, selected pulse width modulation scheme and followed by the device features, static, and dynamic characterization and continues with presenting and discussing the results of extensive experimental and analytical characterization. After this, the impact of GaN HEMTs on inverter volume is discussed in terms of heat sink and output filter volume analysis under different switching frequency and heat sink temperature conditions. The calculation of heat sink volume and single stage LC output filter volume are presented with respect to experimental results of the single phase prototype. The findings from static, dynamic characterization, and single phase prototype results clearly show that GaN HEMT has excellent switching performance under wide load current and heat sink temperature conditions. The high performance of the inverter leads to reduction of the combined total volume, including output filter and heat sink volume. [ABSTRACT FROM AUTHOR]

A switched-capacitor-based dual-switch dc–dc converter with a high-boost voltage gain is proposed in this paper. The proposed converter can obtain a high-voltage gain with a small duty cycle, which decreases the voltage stress and the conduction loss on the power switches. This paper presents the key waveforms, the operating principles at the continuous conduction mode and the discontinuous conduction mode, and the parameter design. Moreover, a comparison between the proposed converter and other nonisolated converters has been completed. To verify the operating principle, a 200 W prototype is constructed with an input voltage of 25–50 V and an output voltage of 200 V. The simulation and experimental results are shown. [ABSTRACT FROM PUBLISHER]

This paper proposes a new bidirectional resonant dc–dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc–dc converters, and meanwhile achieves high efficiency throughout the wide range of operation voltage. It is achieved by configuring a full-bridge mode and a half-bridge mode operation during each switching cycle. A fixed-frequency phase-shift control scheme is proposed and the normalized voltage gain can be always from 0.5 to 1, regardless of the load. The transformer root-mean-square (rms) currents in both the forward and reverse power flow directions have a small variation with respect to the voltage gain, which is beneficial to the conduction losses reduction throughout a wide voltage range. Moreover, the power devices are soft-switched for minimum switching losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology and analysis are verified with experimental results obtained from a 1-kW converter prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid nonisolated dc–dc commutation cell, which is generated by the integration between conventional commutation cell and ladder-type passive switched capacitor (SC) cell. From the resulted hybrid cell are derived three different dc–dc converters: a buck-type, a boost-type, and a buck–boost-type. The three structures are analyzed in this paper and are presented the topological stages, static gain characteristics in continuous conduction mode and discontinuous conduction mode, steady-state analysis. The analyses are generalized in relation to the number of switched-capacitor cells employed, which allows the increase of the rated gain of the converters by adding more SC cells. In addition, the proposed hybrid nonisolated dc–dc commutation divides naturally the voltage stress among the semiconductors and capacitors of the power stage. A 1-kW prototype was developed to verify the operation of the three proposed converters and their theoretical analysis. For the buck-type topology, designed with an input voltage of 600 V and output voltage of 450 V, a peak efficiency of 99.2% and efficiency at rated power of 99% were obtained. [ABSTRACT FROM PUBLISHER]

In this paper, direct torque control (DTC) of five-phase induction motor (FPIM) is implemented using three-level neutral point clamped (TL-NPC) inverter. One of the advantages of three-level inverter over two-level one for DTC operation is the low torque ripple. Also TL-NPC inverter through space vector modulation technique gives low $ dv/dt$ transition with better voltage waveform. By applying conventional lookup table for DTC, the TL-NPC inverter does not ensures lower $dv/dt$ transition. In this paper, a novel switching scheme for DTC of FPIM using TL-NPC inverter is proposed that ensures the low $ dv/dt$ transition and balancing of dc-link capacitor voltages of TL-NPC inverter. To form the lookup table for DTC operation, instead of using voltage vectors directly, virtual vectors (VVs) are utilized. Two switching states are used in one sample time to generate a VV in $\alpha \beta$ plane, which gives zero resultant voltage in $ xy$ plane. The switching strategy ensures low number of transitions to reduce the switching losses. The switching state redundancies are used in a novel way to balance the dc-link capacitor voltages without using any additional hardware. The proposed technique to balance the dc-link capacitor voltage gives lower switching frequency. The MATLAB/Simulink environment is used for the simulation and the results are validated through experiments. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid seven-level converter based on T-type converter and H-bridge cascaded suitable for low-voltage and high-power-density applications. The operation principles and conduction paths are analyzed comprehensively. Voltage balance control of the floating capacitors is the key point of this paper. Mathematical expressions of capacitor voltage balance conditions are deduced based on sinusoidal pulse width modulation (SPWM). The results show that floating capacitor voltages are only balanced when the modulation index is below 0.82 under SPWM. In order to enlarge the modulation index ensuring the capacitor voltage balance, space vector modulation (SVM) is also applied to regulate floating capacitor voltages taking advantage of redundant switching vectors. Meanwhile, in SVM, there are no additional control requirements for the capacitor voltage. Taken both SPWM and SVM into consideration, the limit to the range of operation for this seven-level converter is presented, which is a function of the modulation index and the power factor. The merit of dc voltage utilization improvement in this topology is also analyzed based on simulation results. Simulations and experimental results under different modulation index and RL load are presented to verify the modulation strategies illustrated in this paper. [ABSTRACT FROM PUBLISHER]

In this paper, a new zero voltage zero current transition (ZVZCT) boost DC–DC converter using a coupled inductor is proposed. This topology provides the main switch ZVZCT for the turn-on and zero voltage switching (ZVS) for the turn-off. Moreover, the auxiliary switch turns on at zero current switching (ZCS) and turns off at ZVS. The main diode turns on with ZVT and turns off with ZCS, and other diodes also operate under soft-switching conditions. Besides, due to the coupling effect, the proposed converter improves efficiency additionally since resonant energy in the resonance tank could be transferred to the output, and the circulating current can be limited as well. The soft-switching can be realized in almost all the load rang. In this design, there always exist energy releasing circuits to conduct magnetic flux leakage currents, such that the surge currents are eliminated and switch current stress can be accordingly reduced. All the devices resonate in a unique direction within less than half of a resonance period, so power losses with respect to the resonance can be decreased. In this paper, the converter design and operation principles of the converter are given. It also has been verified by a 1-kW experimental prototype with switching frequency of 100 kHz, and the related experimental results are presented. [ABSTRACT FROM PUBLISHER]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

In this paper, a single-phase single-stage isolated zero current switched (ZCS) current-fed full-bridge ac/dc converter is proposed for IGBT-based high-power power factor correction (PFC) applications. By adding an additional commutation path and few resonant components, ZCS operation is realized for all IGBTs. The conduction loss is also lowered by the additional path. Furthermore, the control strategy for the proposed converter is compatible with that developed for traditional PFC converter. In this paper, the topology derivation and circuit operational analysis are given. The control strategy is introduced. A 3-kw prototype is developed and tested to verify the circuit functionality. Finally, the efficiency performance is investigated and comparison is made to show the advantages of the topology. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel five-level nested neutral point piloted (NNPP) converter and analyzes the operating principle of five-level NNPP converter. This paper presents a novel space vector pulse width modulation (SVPWM) algorithm based on gh coordinate for five-level NNPP converter. First, the common-mode voltage is reduced by choosing the appropriate redundant switching states. After that, the floating-capacitor voltage balance control strategy is presented. The appropriate switch combinations of each phase are determined by the control requirements of floating-capacitor voltages respectively and the hardware mapping method of the switching states is presented. Furthermore, the neutral-point voltage balance control strategy is presented. In order to balance the dc-link capacitor voltages, the seven-segment switching sequence is selected according to the control requirements of dc-link capacitor voltages and the neutral-point voltage regulatory factor is introduced to regulate the durations of the redundant switching states in a switching cycle. Finally, the validity of the novel SVPWM algorithm with decoupling control strategies of floating-capacitor voltages and dc-link capacitor voltages is verified by the experimental results of five-level NNPP converter under steady-state and dynamic conditions. [ABSTRACT FROM AUTHOR]

This paper analyzes three different carrier-based modulation patterns applied to a three-phase high-power-factor-corrected (PFC) five-level buck+boost-type converter acting as an interface between dc distribution systems and an ac grid. The modulation is analyzed employing the space vectors theory so that the achievable performance is demonstrated. The main advantage of the analyzed modulation strategy is its simplicity, which makes it suitable for digital signal controller (DSC) implementations. This seems straightforward for voltage source converters, but is a challenge for current-multilevel converters that typically employ field-programmable gate array devices to achieve better harmonic distortion performance. This is due to modern power electronics DSCs being typically designed for other converter topologies. The power converter is constructed with two phase-shift-modulated six-switch buck-type PFC converters, paralleled by interphase transformers, and an inverting circuit. The system features: bidirectional current carrying capability; relatively low parts count; high utilization of the semiconductors; and low current and voltage ripple at its terminals. The principle of operation, detailed description, analysis of the modulation strategy, and dimensioning equations for three different power circuit realizations are described in this paper assuming the analyzed modulation patterns. The feasibility of the presented converter is demonstrated by means of a constructed hardware prototype. [ABSTRACT FROM AUTHOR]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

An efficient power converter system plays a significant role in the design of battery charging systems for electric vehicles (EVs). In this paper, a new zero-voltage and zero-current switching (ZVZCS) full-bridge dc–dc converter is proposed to reduce the power conversion losses. The proposed converter incorporates a new asymmetrical pulse width modulation (APWM) gating technique for the dc–dc conversion stage in the battery charging system. The proposed dc–dc converter topology achieves zero-voltage switching (ZVS) for all the active switches and near zero-current switching (ZCS) for low-side active switches throughout the charging range of the battery. The proposed APWM technique can reduce the switching and conduction losses compared to the conventional phase-shift modulation (PSM) gating technique. The auxiliary inductance required to ensure ZVS with APWM can also be reduced compared to PSM. Analysis, design, and implementation of the proposed APWM ZVZCS full-bridge dc-dc converter are discussed in this paper. A 100-kHz 1.2-kW laboratory prototype is developed and the experimental results are presented. The results validate the analysis and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper proposes a new approach for the capacitor balancing of a dual three-level T-type converter based on silicon carbide discrete semiconductors. This study is performed while the converter feeds an open-end induction motor. The model predictive control (MPC) scheme is developed to balance the dc-link capacitors and to control the machine torque simultaneously. The proposed technique for MPC reduces the number of redundant switching states that are used in computations without affecting the operating voltage vectors. This reduces the computational time substantially. In addition, the proposed control strategy mitigates the weighting factor tuning problem of capacitor balancing in addition to the conventional MPC cost function. MATLAB simulation results for the proposed drive system under different case studies are presented. Hardware experimental setup for the proposed converter is built, tested, and verified. A comparison between experimental and simulation results is presented. It is observed that the theoretical as well as the experimental results are in full agreement. [ABSTRACT FROM AUTHOR]