Search

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a fifth-order resonant immittance network based dual-active-bridge (DAB) converter and an optimal modulation method that will ensure high-efficiency operation of the converter under wide-range variations in voltage ratio and output power level. The proposed modulation method is based on the concept of total power loss minimization, where a loss model is developed and an optimization algorithm is formulated to compute the optimal set of internal and external phase shift parameters that will lead to the maximum efficiency for a given set of operating parameters including voltage ratio and output power level. It is found that to maintain high-efficiency operation under wide-range variations in voltage ratio and output power level, the DAB converter is required to switch between different operation modes and neither soft-switching operation nor unity-power-factor operation is able to achieve wide-range high efficiency performance when used alone. The importance of $reconfigurability$ of operation mode for achieving wide-range high efficiency performance is clearly illustrated in this paper. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dc power electronic transformer (DCPET) topology for locomotive, ac/dc hybrid grid, dc distribution grid, and other isolated medium-voltage and high-power applications. Compared with conventional PET topology, the proposed DCPET has fewer power semiconductor devices and high-frequency isolation transformers, which can improve the power density and reliability. Fault handling or redundancy design can be achieved to further improve the reliability when some dc–dc modules break down. Also, input voltage sharing control can be omitted to simplify the control system and improve the stability. Meanwhile, soft switching is guaranteed for all the switches, which is beneficial to increase switching frequency and improve power density. In this paper, the principle, evolution, and control of the proposed DCPET are respectively presented and studied in detail. Finally, a prototype of the proposed DCPET is built and the experimental results verify the validity and superiority of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a novel method for instantaneous balancing of neutral-point (NP) voltages with stacked multilevel inverters (MLIs) for variable-speed drives. The stacked MLI uses series-connected dc sources and NPs (connecting points of dc sources) to obtain the desired levels. The balancing of NP voltages are obtained by using a low-voltage-capacitor-fed cascaded H-bridge (CHB) per phase of a symmetrical six-phase induction machine (IM), which ensures zero current drawn from NPs (at any given instant). Since no current is drawn from NPs, the single dc-link operation with stacked capacitors is also possible. The scheme is suitable for applications, where low-voltage dc sources and batteries are stacked to form a dc link. A variable-speed operation is done using a seven-level inverter scheme for a symmetrical six-phase IM, which is formed by three dc-link stacked capacitors cascaded with two low-voltage-capacitor-fed CHBs per phase. Furthermore, the method is extended for an open-end IM to obtain a seven-level common-mode eliminated space vector structure using a single dc link. The generalization of this method for any stacked $n$ -level inverter without NP voltage deviation is also presented in this paper. The experimental results and analysis are included to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the digital implementation of a boundary controller with unipolar switching characteristic for single-phase voltage source full-bridge inverters. This paper expands the application of a second-order switching surface-based control method to unipolar switching of single-phase voltage source inverters (VSIs) using a finite-state machine. The finite-state machine has been formulated considering four different states of the inverter; positive,zero1, negative, andzero2. The second-order boundary control governs the current state of the system and provides proper switching action to keep the system within the desired reference. The control law is implemented digitally in F28m35x digital control card. A full-bridge inverter topology is used to achieve the three-level voltage switching. Various simulations and experiments were performed in a 550 VA, 120 V, 60 Hz VSI with a digitally implemented controller to verify the theoretical predictions. A high-quality voltage output was obtained for various loading conditions. The transient performance of the controller was investigated using a reference and load changes. A comparison of the implementation was made with the existing classical controllers to verify the fast-dynamic response of the system. [ABSTRACT FROM AUTHOR]

Dual active bridge (DAB) based converters offer the benefit of smaller volume due to high-frequency isolation and controllability of active power flow, making them attractive for various applications, such as renewable energy generation, plug-in hybrid vehicles, and distribution systems. This paper presents a novel converter topology along with a modulation strategy for a DAB-based three-phase ac to dc converter. The major benefits are single-stage conversion, no unreliable intermediate dc-link capacitor, reduced number of switches, i.e., only two active switches on the ac side, simple control scheme, open-loop unity power factor operation, bidirectional power flow, and partial soft-switching. This paper presents the analysis of all the operating modes of the converter, resulting in the analytical estimation of power transfer and rms winding current and investigation of soft-switching conditions for the power devices. Simulation and experimental results have been presented to demonstrate the advantages of the proposed technique and accuracy of the analysis.1 [ABSTRACT FROM AUTHOR]

This paper proposes a new bidirectional resonant dc–dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc–dc converters, and meanwhile achieves high efficiency throughout the wide range of operation voltage. It is achieved by configuring a full-bridge mode and a half-bridge mode operation during each switching cycle. A fixed-frequency phase-shift control scheme is proposed and the normalized voltage gain can be always from 0.5 to 1, regardless of the load. The transformer root-mean-square (rms) currents in both the forward and reverse power flow directions have a small variation with respect to the voltage gain, which is beneficial to the conduction losses reduction throughout a wide voltage range. Moreover, the power devices are soft-switched for minimum switching losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology and analysis are verified with experimental results obtained from a 1-kW converter prototype. [ABSTRACT FROM PUBLISHER]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

The three-phase buck rectifier (3ph-BR) is suitable for applications where a voltage step-down function is required. In this paper, an improved 3ph-BR topology is proposed to reduce the voltage stress on the transistors. The freewheeling diode in the conventional topology is split into two diodes in series and the input neutral point is connected to the common point of the two diodes. With the proposed topology and the corresponding modified modulation scheme, the transistors only need to withstand the input phase voltage instead of the line-to-line voltage, bringing about the significant reduction of voltage stress. The proposed topology enables a more cost-efficient and flexible selection of the transistors. Experimental results have verified the validity of the modified topology and associated modulation scheme. [ABSTRACT FROM AUTHOR]

Multilevel converters are widely applied in medium voltage (MV) drive systems due to the attractive features, such as the ability to use devices with lower voltage ratings, high equivalent switching frequency, etc. Recently, a multilevel topology, named seven-level hybrid clamped (7L-HC), is proposed for MV drives. It has a competitive number of devices, showing the potential to build low-cost 7L converters. However, to ensure the wide frequency range operation and power quality of MV drives, its dc-link capacitors and floating capacitors must be controlled properly with balanced voltages. In this paper, an active voltage balancing method is proposed for the 7L-HC converter. This method can effectively balance all the capacitor voltages under a wide frequency range. The method is embedded in the PWM procedure without modifying the control strategies. Simulation and experimental results are provided to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a voltage multiplier topology that is a hybrid between a Cockcroft–Walton multiplier and a Dickson charge pump. The Cockcroft–Walton structure exhibits significant output voltage drop under load as the number of multiplier stage increases. This is because all coupling capacitors are connected in series. Dickson charge pump mitigates this issue by connecting all capacitors in parallel. But this solution comes at the expense of large capacitor voltage stress at the last multiplier stage. The proposed hybrid structure arranges some capacitors in parallel and others in series, thereby achieving low output voltage drop and low capacitor voltage stress at the same time. We develop a model that predicts hybrid multiplier's performance and validates it experimentally. We also demonstrate a 60–2.25 kV dc–dc converter based on a 16-stage hybrid voltage multiplier which achieves a voltage gain of 12.8 while keeping the highest capacitor voltage stress to 660 V. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]

A systematic method for developing ultra-wide output voltage range power supply based on modular switched-converter principle is proposed in this paper. The basic symmetric switched-converter (SSC) module is composed of two dc–dc modules, two diodes, and one active switch. Multi-stage SSC modules are generated by symmetric cascaded connection method. By controlling the active switches in multi-stage SSC modules, the connections of all the dc–dc modules’ output ports can be changed flexibly among series, parallel, and partial–parallel–partial-series connections. Then segmented regulation can be realized and system output voltage range can be widely extended. Meanwhile, the voltage range of each dc–dc module can be narrowed and the voltage/current stress can be reduced to simplify the design, increase device utilization ratio, and improve overall efficiency. A full-bridge isolated buck–boost converter with a semiactive rectifier, which features soft-switching and wide voltage adjustment range, is adopted as the dc–dc module to realize the proposed system. Input current sharing control strategy is adopted to ensure proper power balancing in all possible operating modes. The stability of the proposed system is also explored. Simulation and experimental results are provided to verify the effectiveness and advantages of the proposed system configuration, the switched-converter principle, and the control strategies. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a three-phase, five-level, non-regenerative pulsewidth modulated rectifier using only two active switches (minimum required) per phase, which drastically reduces gate driver requirement and hardware complexity. It draws sinusoidal input current at close to unity power factor. All the semiconductor devices are rated at only one fourth of the dc-link voltage, and none of them requires any transient voltage balancing snubber. A total of 8 out of the 14 diodes per phase undergo soft switching transition under all operating conditions, which increases its efficiency. No extra hardware circuitry for balancing the flying capacitors (FCs) or the dc-link mid-point voltage are required, which further reduces hardware complexity and increases the conversion efficiency. The proposed topology does not need any sophisticated startup procedure for charging the FCs either, which solves the problem of semiconductor overvoltage during starting. A 3-kW laboratory prototype is built to experimentally verify the proposed topology. The maximum efficiency obtained from the prototype is 98.7%, and it is always more than 96% for the load range from 15% to its rated. [ABSTRACT FROM AUTHOR]

In order to provide high and extendable power levels for inductive power transfer (IPT) system, a parallel multi-inverter system based on modular inverter is presented. Various power requirements can be implemented by an adjustment of the number of paralleled inverters, which provides a high modularity. A master−slave scheme is employed for the switching-driver signals of parallel inverters, where one acts as a leader while others act as followers. Despite the master−slave scheme, the proposed circuit topology has natural robustness because of the equality in terms of the hardware configuration of each modular inverter. For proper parameters, the output phase (current lagging corresponding voltage) of an inverter is lower than the average of output phase of all inverters, when its output voltage lags behind others, and vice versa. Based on this approach, PI controllers are designed to implement phase synchronization for output voltages of all inverters. An IPT prototype supplied by the proposed parallel multi-inverter with three inverters was designed, built, and tested. Experiments show that the proposed parallel multi-inverter system has not only good circulating current suppression capacity but also excellent performance of phase synchronization. The maximum dc−dc efficiency was 94% at a 35.1 kW receiving power. This paper is accompanied by a Matlab/Simulink file demonstrating phase synchronization control. [ABSTRACT FROM AUTHOR]

In this paper, a systematic and analytical study of non-isolated topologies belonging to the family of reduced redundant power processing (R2P2) converters is presented. Based on this study, all the non-isolated R2P2 topologies that can be implemented in reality are derived. Detailed examples clarify all possible cases of this analysis. In addition to this, the voltage ratio and the efficiency for each one of the R2P2 configurations are calculated, being further illustrated with examples. A comparison among configurations is also discussed with criteria the high step-up voltage gain and efficiency, aiming for high-power applications. One of these R2P2 converters is selected for further examination, as the most suitable for such applications. The theoretical analysis, as well as the calculations of the step-up voltage ratio and efficiency of the selected converter, is compared to experimental results conducted on a 2-kW laboratory prototype designed to operate in various step-up voltage ratios and in a high-power range, proving the effectiveness of the proposed investigation. [ABSTRACT FROM AUTHOR]

A three-phase three-level (TPTL) converter is an optimal alternative for high-input and high-power dc/dc conversion system. The voltage stress on the primary switch is only half of the input voltage due to its three-level (TL) structure, and the current rating of power devices can be reduced by the three-phase configuration. To achieve soft switching and improve efficiency, the resonant tank can be introduced to optimize the performance of the converter. In this paper, a novel TPTL LC-type series resonant converter with few switches and simple configuration is proposed. The voltage stress on all switches can be reduced to the half of the input voltage, and the voltage across output rectifiers is clamped to the output voltage; as a result, the proposed converter is suitable for high-input/output applications. Meanwhile, the ripple frequency of the output current can be increased significantly, resulting in a reduced filter requirement. Variable frequency control strategy is adopted in order to obtain zero-voltage switching for all switches and zero-current switching for all rectifier diodes in wide input voltage and load range. In this paper, the comprehensive analysis on the proposed converter is carried out, including the operation mode classification, the operating mechanism under different operation mode, along with the circuit model, and gain characteristics of the converter by the fundamental harmonic analysis. Experimental results from a 440–590 V input and 400 V/5 A output are presented to verify the theoretical analysis and the performance of the converter. [ABSTRACT FROM AUTHOR]

This paper extends the voltage-doubler concept to the single-phase SEPIC rectifier in discontinuous conduction mode and, as a consequence, novel rectifiers are proposed. A comparison with the classic SEPIC rectifier shows that the proposed converters can either provide reduced voltage stress on the semiconductors for the same output voltage level or supply double the gain of the output voltage with the same voltage stress. The proposed voltage-doubler SEPIC rectifiers provide a high power factor with no current control and they can be applied in order to improve the static gain of the structure, which can make the SEPIC rectifier suitable for applications that require a high voltage level. In this paper, the generic structure based on a three-state switch, four different implementations of the proposed concept (including bridgeless structures), steady-state analysis, a dynamic model, system control, and experimental results are presented. The proposed rectifiers were verified by experimental results obtained with a prototype built with the following specifications: 1000 W output power, 220 V input voltage, 400 V output voltage, and 50 kHz switching frequency. Peak efficiency of 95.84%, THD of 2%, and power factor of 0.9997 were obtained and, most importantly, double the gain of the output voltage was verified. [ABSTRACT FROM AUTHOR]

For the conventional PFC rectifiers, the high efficiency cannot be achieved over a wide input range, and the efficiency will be greatly decreased at low-input voltages. In order to overcome the efficiency bottleneck under low-line input, a flexible mode bridgeless boost power factor correction (PFC) rectifier is proposed in this paper. According to the input voltage, the proposed rectifier can be flexibly adapted to the suitable operating mode to obtain the maximum efficiency. Meanwhile, the circuit components can be reused by different operating modes, so the extra cost is low. In the proposed rectifier, a back-to-back bridgeless boost PFC topology is adopted at high-line conditions and a three-level bridgeless boost PFC topology is rebuilt to reduce the switching losses at low-line conditions. Compared with the traditional bridgeless boost PFC rectifier, an extra low-voltage bidirectional switch (usually composed of two switches) is added, so the increased cost is low. In addition, the low common-mode noise can be achieved at both high- and low-line conditions due to the direct connection between the input mains and the output electrolytic capacitor. The detailed principle analysis about the proposed rectifier is presented in this paper. Finally, an experimental prototype is built to verify the feasibility and the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

This paper presents a novel family of single-switch resonant dc–dc converters with low switch voltage stress. The single-switch resonant converter which has a ground-referenced switch is advantageous for implementing the gate drive circuit and operating at several-MHz switching frequency. However, the conventional ones mostly have high voltage stress on the switch, roughly 4–5 times the input voltage. In this paper, we propose the single-switch converter topologies derived from the drain-source impedance networks consisting of two inductors and two capacitors. The switch voltage of the proposed converters is shaped into a near trapezoid by designing the resonant networks to have the desired drain-source impedance. Furthermore, a simple and specific design scheme is presented here so that the peak switch voltage is lowered to 2.2–2.5 times the input voltage while zero voltage switching is achieved. Experimental results from a 20-W GaN-based prototype operating at 10 MHz demonstrate the feasibility of the proposed converter topologies and the design method. [ABSTRACT FROM AUTHOR]

This paper proposes a dual-space vector control scheme for the open-end winding permanent magnet synchronous motor (OEW-PMSM) drive fed by the dual inverter with a single dc supply. Potential zero-sequence current in the open-end winding drive system has to be considered since it causes circulating current in the winding and leads to high current stress of power semiconductor devices and high losses. Zero-sequence current in open-end winding ac motor drives is usually caused by the zero-sequence voltage, and therefore switching combinations which do not produce zero-sequence voltage are used to synthesize the reference voltage in existing methods. But even so, the zero-sequence voltage can also be produced by the dead time of the inverter. In order to suppress zero-sequence current in the OEW-PMSM drive, a dual-space vector control scheme is proposed and a novel dual-inverter space vector pulse width modulation (PWM) with the zero-sequence voltage reference is employed to regulate system zero-sequence voltage in this paper. Compared with existing dual inverter PWM strategies, the novel algorithm build a regulation mechanism for the zero-sequence voltage. The proposed method is compared with the conventional vector control by simulations and experiments, and the results shown that the proposed scheme can suppress zero-sequence current effectively. [ABSTRACT FROM AUTHOR]

In this paper, the Z-source converter is introduced to power factor correction (PFC) applications. The concept is demonstrated through a wireless power transfer (WPT) system for electric vehicle battery charging, namely Z-source resonant converter (ZSRC). Due to the Z-source network (ZSN), the ZSRC inherently performs PFC and regulate the system output voltage simultaneously, without adding extra semiconductor devices and control circuitry to the conventional WPT system such as conventional PFC converters do. In other words, the ZSN can be categorized as a family of the single-stage PFC converters. In addition, the ZSN is suitable for high-power applications since it is immune to shoot-through states, which increases reliability and adds a boost feature to the system. The ZSRC-based WPT system operating principle is described and analyzed in this paper. Simulations and experimental results based on a 1-kW prototype with 20-cm air gap between the system primary and secondary sides are presented to validate the analysis and demonstrate the effectiveness of the ZSN in the PFC of the WPT system. [ABSTRACT FROM PUBLISHER]

Various magnetically coupled impedance source (MCIS) networks have been proposed in the literature for increasing voltage gain and modulation index simultaneously while reducing the number of passive components used in the converter. However, applications of such networks have been limited by their discontinuous currents drawn from the sources and/or high stresses experienced by their components. This paper thus proposes three new MCIS networks named, respectively, as quasi-Y-source, quasi-Γ-Z-source, and quasi-T-source or quasi-trans-Z-source networks. These new networks inherit all advantages of the existing MCIS networks. In addition, they demonstrate advantages like continuous input currents, reduced source stresses, and lower component ratings that are not achievable by other existing networks. Further, dc-current-blocking capacitors used in the networks help to avoid saturation of magnetic core. Derivations of all two-winding MCIS networks, including existing and new networks, from the generalized three-winding MCIS networks are then systematically illustrated, before comparing them. Operational principles, mathematical derivations, simulation, and experimental results of all studied networks have been presented in the paper. [ABSTRACT FROM PUBLISHER]

Modular multilevel converters (MMCs) are being developed for the grid connection of offshore wind or tidal farms. In order to reduce the construction and maintenance costs, it is desirable to reduce the weight and volume of the system. In current MMC submodule designs, the reservoir capacitor usually accounts for over 50% of the total volume and 80% of weight. This paper presents a new design concept and control principle for a submodule using the stacked switched capacitor (SSC) architecture that can significantly reduce the capacitor size in an MMC. Practical considerations for a high-voltage high-power SSC-based MMC submodule are presented in this paper, through the design of a 21-level, 40-kV (pole-pole dc), 19.1-MW, grid-connected system, and the concept is demonstrated experimenttally on a scaled-down 400-V, 12.3-Apeak laboratory prototype submodule. It is shown that with the proposed SSC architecture, the total volume of capacitors in each submodule can be reduced by more than 40% without significantly increasing the power loss. [ABSTRACT FROM AUTHOR]

The increasing interest in multiphase drive systems has led to the extension of inverter topologies and pulse width modulation (PWM) methods from three-phase to multiphase occasions. Carrier-based PWM (CPWM) dominates space vector PWM when the phase number increases, because of its simple computation and modular implementation. Although intensive work has been done on modifying PWM methods to reduce the common-mode voltage (CMV), not enough work has been done on CPWM methods with CMV reduction for multiphase drives. This paper extends the phase-shifted sinusoidal PWM (PS-SPWM) method for five-phase and six-phase two-level voltage-source inverters (VSI) and employs the intersection-plotting method and Fourier analysis to reveal the nature of the CMV. Both experiment and simulation results comply with theoretical analysis that compared with the conventional SPWM, the PS-SPWM can effectively reduce the CMV in peak-to-peak value and RMS value, though it leads to a higher phase current distortion. In addition, the hardware realization of PS-SPWM for multiphase inverters by a distributed control system is presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a novel modular equalization architecture for series-connected electric double-layer capacitor (EDLC) modules, each consisting of multiple cells connected in series. Cell voltages in a module are equalized by an inductive voltage divider (IVD)-voltage multiplier (VM)-based cell equalizer, while module voltages are unified by switched capacitor converters (SCCs). Square wave voltages generated at switching nodes of the IVD-VM-based cell equalizers are utilized to drive the SCC-based module equalizers, realizing the switchless topology of SCC-based module equalizers. The required switch count of the proposed system can be halved compared to conventional systems, allowing simplified circuit. An experimental equalization test for three EDLC modules, each consisting of six cells in series, was performed from an initially voltage-imbalanced condition. Module and cell voltages were equalized at different rates, and the equalization performance of the proposed modular equalization system was successfully demonstrated. [ABSTRACT FROM AUTHOR]

This paper presents an improved H8 power converter for common-mode voltage (CMV) reduction and electromagnetic interference suppression. The proposed H8 converter can realize zero CMV variation when entering and leaving the zero state, which is mainly achieved by both the improvement of the structure and the control strategy. For the system structure, two switches are added on the dc bus to float the ac part of the three-phase converter in the zero state. Besides, additional capacitors are used to realize controllable CMV. For the control strategy, a simple control strategy is proposed for the H8 converter. It can automatically adapt to the flowing orientation of the load current to realize synchronous switching of the power switches, which effectively eliminates the impact of the dead time. Through analysis, simulations, and experiment, a comparison between the proposed H8 converter and the conventional H6 converter is performed. Results validate the effectiveness of the H8 topology. [ABSTRACT FROM AUTHOR]

Due to the zero-sequence currents in the four-wire systems, the three-phase currents become more complex on both amplitudes and phases in the unbalanced load conditions, so that the existing open-circuit (OC) fault diagnosis methods of the switching devices cannot be directly used. In this paper, an OC fault diagnosis strategy applied to four-wire T-type converter systems is proposed, which is implemented by decomposing the circuit model into a positive- and negative-sequence model and a zero-sequence model, and locating the OC fault based on the law of positive- and negative-sequence voltage error offsets and zero-sequence voltage error offsets. The proposed diagnosis method is suitable for both unbalanced load and unbalanced input voltage conditions. Meanwhile, the differences of fault-tolerant control between four-wire and three-wire systems are analyzed and compared. An effective fault tolerance strategy for inner OC faults applied to four-wire T-type converter systems is presented, which owns the ability to suppress dc bus imbalance. Simulation and experimental results are presented to verify the correctness of the proposed strategy. [ABSTRACT FROM AUTHOR]

Several applications need a high power, high output voltage ac/dc converter. The structure includes a dc/dc resonant stage, which is fed from a three-phase line. Due to standards, rectified dc input voltage varies largely from 400 to 750 V affecting the adversely overall design and current levels. In fact, losses in the inverter become unbearable if both switching frequency and transferred power are desired beyond a certain level. In those cases, it is necessary to connect several switches in parallel. As an alternative, the new switches can configure a new modular structure instead, adding more flexibility in the control to compensate input voltage variations. As a result, the required circulating current is reduced to a half, with benefits in total power losses. Moreover, the nature of the topology allows a reconfiguration of the resonant net (LCC) for low power, reducing even further the minimum circulating current under those conditions (fluoroscopy, for instance). In this paper, the new multilevel resonant topology is mathematically modeled and proposed for radiography and fluoroscopy. An example illustrates the design procedure for a given application at 100 kW, 50–150 kV. [ABSTRACT FROM AUTHOR]

In this paper, a developed structure is proposed for high step-up nonisolated noncoupled inductor based multiport dc–dc converters. The voltage gain per number of devices of the proposed topology is higher than that of similar topologies. This means that, by using the same number of devices, the proposed topology can generate higher gains than other structures. In other words, the proposed topology utilizes less number of devices for producing the same voltage gain, which leads to less total cost, size, weight, and complexity. Despite high voltage gain, the normalized peak inverse voltage (NPIV) on switches/diodes is low. Higher number of input ports leads to higher gains and lower NPIVs on devices. The load energy can be absorbed and stored in first input unit. Modularity, simple structure, continuous input currents, and low input current ripple are the other profits of proposed topology. Low/medium power applications are suggested for the proposed structure. Proposed topology has been explained and operational modes along with steady-state analysis have been discussed. For better verification, the proposed topology has been compared with several multiport high gain converters. Comparison results confirm the advantages of the proposed topology. Finally, the proper performance of the proposed topology has been validated by experimental results. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

In this paper, a family of step-up resonant switched-capacitor converters (RSCs) with a continuously adjustable conversion ratio is proposed based on the Cuk dual-resonance core (DRC) featuring two resonant paths. By adopting the on-time fixed frequency modulation, the two resonant paths can conduct simultaneously and satisfy the charge balance of the flying capacitor during the overlapping period. As a result, the conversion ratio—upper bounded by two determined by the circuit configuration—can vary continuously and efficiently even at the light load condition (1/10 of the rated power). A comprehensive analysis—the operation principle, voltage-gain curve, and voltage/current stresses—about the DRC is given. In addition, the Cuk DRC was extended to the series–parallel switched-capacitor converter (SCC), Fibonacci SCC, and voltage doubler to form a family of step-up RSCs, whose voltage-gain curves of different topologies are derived. Moreover, a characteristic comparison between the Cuk DRC and the traditional “direct” and “indirect” resonant core is given. Then, a 48 to 62–94.6 V resonant core with peak efficiency 97.8% and maximum power 120 W under the open loop condition was built. The analyses were verified by both experimental and simulation results. [ABSTRACT FROM AUTHOR]

The five-level nested neutral-point-clamped (5L-NNPC) converter is one of the most promising topologies for medium-voltage (2.3–7.2 kV) high-power applications such as medium-voltage drives, wind energy conversion systems, and grid-connected systems. The 5L-NNPC requires a fewer number of switching devices, freewheeling and clamping diodes, and flying capacitors compared to the existing five-level multilevel converters. In the 5L-NNPC topology, each flying capacitor voltage is regulated at one-fourth of the dc-bus voltage to obtain the five-level operation. Due to the lack of redundant switching states, it is difficult to control the flying capacitor voltages by using the pulse-width-modulation-based classical control methods. This paper proposes a model-predictive current control (MPCC) approach to control the flying capacitor voltages along with the output currents of the 5L-NNPC converter. The discrete-time model of 5L-NNPC is developed to implement the MPCC scheme. The simulation and experimental studies are conducted to verify the dynamic and steady-state performance of 5L-NNPC with the MPCC scheme. The performance of the proposed MPCC approach is compared with the conventional space-vector-modulation-based voltage-balancing approach. Furthermore, the flying capacitor voltage control capability of MPCC is verified at different load power factors. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

This paper presents an overview of resonant and hybrid switched-capacitor converters with a particular focus on multimode operation. The multimode approach is discussed as a tool to affect high efficiency and power density across a wide load range, provide variable regulation, and, as a general framework, to conceptualize the advantages and opportunities of the approach compared to more traditional dc–dc converters. A general analysis is provided to quantify the advantage of hybrid and resonant converters that factors in the tradeoffs between size and loss in the magnetic component and voltage stress on the active devices. A broader set of operating modes is presented that spans continuous and discontinuous conduction and includes resonant, quasi-resonant, and more traditional buck- or boost-like operation. A prototype flying-capacitor multilevel converter is presented to demonstrate the variety of operating modes and motivate important considerations such as voltage balance on the flying capacitors. [ABSTRACT FROM AUTHOR]

The trend toward higher switching frequencies and higher power densities in dc–dc conversion led the designers to rediscover resonant topologies. However, the analysis of these converters is often limited to a particular operating mode and/or topology. This paper wants to fill the gap by presenting a state-space-based analysis for a broad class of series-resonant converters including voltage-fed as well as current-fed topologies, either unidirectional or bidirectional. The proposed solution consists of a mathematical framework that solves the trajectory of state variables in the resonant tank, as well as the main characteristic functions such as voltage conversion ratio and transferred power. The matrix approach permits a flexible and compact formulation and easy implementation in computational tools such as MATLAB. The theoretical framework is applied to both voltage-fed and current-fed resonant topologies: the first is used to show the advantages of the proposed model respect to the first harmonic approximation, while a detailed analysis in terms of operating mode boundaries, delivered power, and voltage gain is provided for the second. Simulations and measurements on a 300-W prototype of the current-fed topology are used to validate the correctness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents a dynamic power flow management system for a solar photovoltaic (PV) system employing a single-stage single-inductor-based dual-input/output dc–dc converter feeding standalone dc loads backed up by a rechargeable battery. A time-sharing voltage-mode control scheme has been proposed for power flow management between solar PV, a battery, and a standalone dc load, and it also maintains a constant dc load voltage and performs maximum power point tracking operation of solar PV. The implementation of the control scheme has been described in detail. The steady-state performance of the single-stage converter has been explained with the relevant analytical expressions derived along with the characteristics. A state-space average model was developed for simulating the transient behavior and validating the working of the system for step changes in the input solar PV power and the dc loads. A hardware prototype of the proposed system has been fabricated, and the proposed controller has been implemented using the dSPACE DS1103 real-time interface board. The working of the proposed scheme for different levels of input solar insolation and dc load power demand has been satisfactorily demonstrated, and the corresponding results are also provided. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) for battery charging applications has significant advantages over the traditional plug-in system. Since misalignment between the primary and secondary windings is inevitable, it is of significance to improve the misalignment tolerance of IPT systems with constant-current (CC) and constant-voltage (CV) outputs for battery charging. In this paper, the load-independent output characteristic of the hybrid topology and the function switching between CC and CV of the reconfigurable topology are analyzed. Besides, a hybrid and reconfigurable IPT system with 3-D misalignment tolerance for CC and CV outputs is proposed, simplifying or even canceling control schemes. Moreover, a novel parametric design method is given for the IPT system, which can suppress the fluctuation of the output voltage/current within a certain range of misalignment. In order to validate the performance of the proposed topology, a 1-kW prototype is built, and the corresponding experiments are carried out. In the CC/CV mode, the system can operate with the longitudinal misalignment to 50% when the load varies from 36 to 480 Ω, and the fluctuation of the output current/voltage is within 5%. Similarly, the misalignment in Y- and Z-axis is 12.5% and 33.3%, respectively. [ABSTRACT FROM AUTHOR]

This paper presents a novel three-phase DC-link multilevel inverter topology with reduced number of input DC power supplies. The proposed inverter consists of series-connected half-bridge modules to generate the multilevel waveform and a simple H-bridge module, acting as a polarity generator. The inverter output voltage is transferred to the load through a three-phase transformer, which facilitates a galvanic isolation between the inverter and the load. The proposed topology features many advantages when compared with the conventional multilevel inverters proposed in the literatures. These features include scalability, simple control, reduced number of DC voltage sources, and less devices count. A simple sinusoidal pulse-width modulation technique is employed to control the proposed inverter. The performance of the inverter is evaluated under different loading conditions and a comparison with some existing topologies is also presented. The feasibility and effectiveness of the proposed inverter are confirmed through simulation and experimental studies using a scaled down low-voltage laboratory prototype. [ABSTRACT FROM AUTHOR]

This paper presents a new predictive power-factor-correction (PFC) controller for series-interleaved three-level boost (TLB) converters. Compared to the state-of-the-art TLB PFC controllers, where a two-cycle prediction and a detection of an operating region are necessary, the proposed controller achieves a low total harmonic distortion of the input current by using a single equation to predict the input current in all operating regions of the converter, in just one operating cycle. The average current control is achieved by sampling at the peak of the triangular carrier. The proposed PFC controller significantly reduces the distortion of the input ac current near the zero-crossing points, resulting in a low total harmonic distortion of the input current. The operation of the proposed controller was evaluated, and its stability and robustness to parameter changes was confirmed analytically. The controller operating principles were verified in simulations and validated by experiments on a medium-voltage 50-kW converter prototype. [ABSTRACT FROM AUTHOR]

A family of dimmable ac light-emitting-diode (LED) drivers fed from dc voltages, is presented in this paper based on zero-current-switching quasi-resonant converters. The proposed family of drivers is based on replacing the diode in the conventional converter topologies (i.e., buck, boost, or buck–boost) by a string of high-brightness LEDs (HB-LEDs). Hence, the HB-LED string will be working as the rectifier diode and the load, switching at the same frequency of the main switch. In this case, the output current, which is experimentally validated, shows a negative current peak due to the reverse-recovery effect of the HB-LEDs. In order to reduce the reverse-recovery effect on the HB-LEDs, the main switch of the proposed topologies is replaced with a full-wave resonant switch, which makes possible to reduce the di/dt during the turn-off of the HB-LED string, therefore the reverse-recovery effect is eliminated. Moreover, the dimming of the HB-LEDs is done by means of changing the switching frequency of the converter by varying the turn-off, while keeping a constant turn-on time. The proposed converters are suggested to be used in a postregulator stage of an ac–dc converter or as the interface between the low-voltage bus and the HB-LED string in a dc nanogrid. In order to validate the analysis, the proposed topologies have been experimentally tested on a constructed prototype with an output power of 7.5 W, that is able to achieve an electrical efficiency of 94.5% and a luminous efficacy of 110 lm/W at full load. Moreover, the analysis has been extended to a comparison in terms of reliability with the conventional topologies on a 700-h test. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

This paper presents the active capacitor voltage-balancing (ACVB) methods based on the dynamic model for a five-level nested neutral-point piloted (NNPP) converter using hybrid carrier modulation. The traditional hybrid carrier modulation provides natural voltage balancing of floating capacitors and dc-link capacitors. First, the natural voltage-balancing ability under steady-state and ideal conditions is theoretically proved. However, there are accumulated errors and deviations of capacitor voltages in practical applications, especially under dynamic conditions. In order to address the accumulated errors and deviations of capacitor voltages, the dynamic models of floating-capacitor voltages and neutral-point voltage are established. Moreover, the ACVB method based on the dynamic model of the neutral-point voltage is proposed by injecting the zero-sequence voltage. And the ACVB method based on the dynamic model of floating-capacitor voltages is proposed by introducing the adjustment variables. The proposed ACVB methods have the advantages of simple formula, definite physical meaning, and high accuracy. Furthermore, the output voltage quality and current quality are evaluated in term of total harmonic distortion and the effect of model parameter mismatch on the proposed ACVB methods is presented. Finally, the comparative simulation and experimental results verify the correctness of the proposed ACVB methods based on the dynamic model under different conditions. [ABSTRACT FROM AUTHOR]

In this paper, a novel platform for the single phase switched-capacitor multilevel inverters (SCMLIs) is presented. It has several advantages over the classical topologies, such as an appropriate boosting property, higher efficiency, lower number of required dc voltage sources, and other accompanying components with less complexity and lower cost. The basic structure of the proposed converter is capable of making nine-level of the output voltage under different kinds of loading conditions. Hereby, by using the same two capacitors paralleled to a single dc source, a switched-capacitor (SC) cell is made that contributes to boosting the value of the input voltage. In this case, the balanced voltage of the capacitors can be precisely provided on the basis of the series–parallel technique and the redundant switching states. Afterward, to reach the higher number of output voltage levels, two suggested SC cells are connected to each other with a new extended configuration. Therefore, by the use of a reasonable number of required power electronic devices, and also by utilizing only two isolated dc voltage sources, which their magnitudes can be designed based on either symmetric or asymmetric types, a 17- and 49-level of the output voltage are obtained. Based on the proposed extended configuration, a new generalized version of SCMLIs is also derived. To confirm the precise performance of the proposed topologies, apart from the theoretical analysis and a complete comparison, several simulation and experimental results are also given. [ABSTRACT FROM AUTHOR]