Search

For current-controlled grid-connected inverters with LCL filter, the essence of grid voltage full feedback is to improve the output impedance of grid-connected inverters to infinity, which can eliminate the influences of grid voltage distortion and the non-negligible grid impedance. However, existing full feedforward strategies are complex and control delay cannot be compensated precisely, which leads to the instability of system when the full feedforward of the voltage at the point of common coupling under the weak grid is adopted. This article first proposes a simplified full feedforward strategy based on grid-side inductor volt-age differential feedback active damping (GIVD-AD). Second, repetitive prediction (RP) is used to compensate for the control delay. Then, a virtual impedance branch is added and an adaptive algorithm for modifying virtual impedance based on the difference between predicted grid voltages by Newton interpolation prediction (NIP) and RP is proposed. With the proposed method, grid-connected inverters can work stably when grid impedance changes suddenly and exhibit strong rejection ability against grid-voltage harmonics. Finally, simulative and experimental results from a 3-kW single-phase grid-connected inverter are provided to prove the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

Soft-switching technique contributes to higher conversion efficiency and switching frequency for transformerless grid-connected inverters (TLIs), which is beneficial to improve power density and reduce cost. However, existing soft-switching TLIs can only operate with unity power factor; as a consequence, they could not supply reactive power required by newly technical standards. In order to solve this issue, a novel zero-voltage-transition (ZVT) scheme has been proposed in this article, and two resonant tanks with a compact structure are applied in H6-type topology. The derived ZVT inverter enables high-frequency switches of both positive and negative power regions to be turned on and off under zero-voltage conditions, as well as all auxiliary switches can be turned on with zero-current switching. Meanwhile, unipolar differential-mode voltage and constant common-mode voltage characteristics are also maintained. Finally, comprehensive experiment results from a 100-kHz/1-kW prototype are provided to verify the correctness of the proposed inverter. [ABSTRACT FROM AUTHOR]

Transformerless grid-connected inverters (TLI) feature high efficiency, low cost, low volume, and weight due to using neither line-frequency transformers nor high-frequency transformers. Therefore, TLIs have been extensively investigated in the academic community and popularly installed in distributed photovoltaic grid-connected systems during the past decade. This article analyzes and summarizes the state of the art of TLI techniques, three rules of maintaining constant common-mode voltage (CMV) of TLIs at switching frequency have been concluded from a generic CMV analysis model at the beginning. Second, suppression methods of leakage current (LC) and dc current injection (DCCI), so-called two key challenges for first-generation TLIs, have been classified and discussed in detail, respectively. Finally, future trends and some challenges of TLIs based on wide bandgap devices named second-generation TLIs have been presented in this article. [ABSTRACT FROM AUTHOR]

The current-voltage-fed bidirectional dc-dc converter, which refers to a current-fed inverter at low voltage side and a voltage-fed inverter at high voltage side, can realize zero voltage switching (ZVS) for the switches with the use of phase-shift (PS) technology. However, the current-fed switches suffer from high voltage spike and high circulating conduction loss. In order to solve these problems, a novel phase-shift plus pulsewidth modulation (PSP) control ZVS bidirectional dc-dc converter is proposed in this paper. By adopting active clamping branch and PSP technology, the converter can realize ZVS for all switches in a wide range of load variation while input or output voltage varies. In addition, a novel control strategy with one port voltage regulation and another port current regulation is proposed to make energy bidirectional conversion freely. The operation principle is analyzed and verified by a 28V/270V conversion prototype rated at 1.5kW. [ABSTRACT FROM AUTHOR]

This letter proposes a fast current control scheme for ac drives by minimizing the latency from current sampling to the updation of a pulsewidth-modulation (PWM) command. By reconstructing the architecture of a linear controller, the minimal necessary steps to obtain the output voltage are deduced as the primary calculation, and the other computation work of the current loop is done in the postcalculation after updating the PWM command. With the proposed method, the computational delay is reduced with negligible loss in the available modulation index, and a higher stability margin or system bandwidth is realized. Also, the developed controller structure exhibits inherited antiwindup characteristics. The technique has been validated by experimental investigations on a permanent magnet synchronous motor. [ABSTRACT FROM AUTHOR]

Thermal drift-caused current measurement offset error usually results in unfavorable torque ripples of fundamental frequency, and hence a compensation method for current offset error is proposed in this article, which is initially derived based on the nonsalient-pole machines and then extended to the salient-pole machines. By filtering the difference between the predicted currents from a simple nominal model and the measured currents, the offset error is directly estimated and then compensated with minimal effects on the current dynamics. It is proved that the estimation is accurate if the filter has unity gain at the frequency of the offset error. Therefore, the proposed method is free of the current regulator type and shows strong robustness against machine parameter deviations. It can also stably work even when the output voltage is saturated. Two kinds of filters are designed in the stationary reference frame, and the low-pass filter with low bandwidth is recommended for its easy implementation. Finally, the effectiveness of the proposed method is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]