Search

This study is focused on integration and operation of a single-phase bidirectional inverter with two buck/boost maximum power point trackers (MPPTs) for dc-distribution applications. In a dc-distribution system, a bidirectional inverter is required to control the power flow between dc bus and ac grid, and to regulate the dc bus to a certain range of voltages. A droop regulation mechanism according to the inverter inductor current levels to reduce capacitor size, balance power flow, and accommodate load variation is proposed. Since the photovoltaic (PV) array voltage can vary from 0 to 600 V, especially with thin-film PV panels, the MPPT topology is formed with buck and boost converters to operate at the dc-bus voltage around 380 V, reducing the voltage stress of its followed inverter. Additionally, the controller can online check the input configuration of the two MPPTs, equally distribute the PV-array output current to the two MPPTs in parallel operation, and switch control laws to smooth out mode transition. A comparison between the conventional boost MPPT and the proposed buck/boost MPPT integrated with a PV inverter is also presented. Experimental results obtained from a 5-kW system have verified the discussion and feasibility. [ABSTRACT FROM AUTHOR]

This paper presents two-phase modulated digital control for a three-phase bidirectional inverter with wide inductance variation in dc distribution systems. The bidirectional inverter can fulfill both grid connection and rectification with power factor correction. With the proposed control, the inverter can track its sinusoidal reference currents, and it is allowed to have wide inductance variation, reducing core size significantly. The control laws based on space-vector pulsewidth modulation are first derived with either an accurate approach or an approximated one, and the gate signals were then derived based on two-phase modulation for lower switching loss and switching noise spectra. Determination of control parameters and stability analysis are also presented. In the design and implementation, the inductances corresponding to various inductor currents were measured and tabulated into a single-chip microcontroller for tuning loop gain cycle by cycle, ensuring system stability. Measured results from a 10 kVA 3φ bidirectional inverter have been presented to confirm the feasibility of the discussed control approaches. [ABSTRACT FROM AUTHOR]

This paper presents dc-bus voltage control with a three-phase bidirectional inverter for dc distribution systems. The bidirectional inverter can fulfill both grid connection and rectification modes with power factor correction. The proposed control includes two approaches, one line-cycle regulation approach (OLCRA) and one-sixth line-cycle regulation approach (OSLCRA), which take into account dc-bus capacitance and control dc-bus voltage to track a linear relationship between the dc-bus voltage and inverter inductor current. Since both of the approaches require the parameter of dc-bus capacitance, this paper first presents determination of dc-bus capacitor size and an online capacitance estimation method. With the OLCRA, the inverter tunes the dc-bus voltage every line cycle, which can reduce the frequency of operation-mode change and current distortion. The OSLCRA adjusts current command every one-sixth line cycle to adapt to abrupt dc-bus voltage variation. The two approaches together can prevent dc-bus voltage from wide variation and improve the availability of the dc distribution systems without increasing dc-bus capacitance. Experimental results measured from a three-phase bidirectional inverter have verified the feasibility of the discussed control approaches. [ABSTRACT FROM AUTHOR]

This paper presents design and implementation of a 5-kW single-phase bidirectional inverter with wide inductance variation. For dc-microgrid applications, the bidirectional inverter has to fulfill grid connection and rectification with power factor correction to regulate the dc bus to a certain range of voltages. In the inverter operation, inductor current can vary from 0 to 32 A in one line cycle. This will result in wide inductance variation, around seven times for an inductor constructed with a molybdenum permalloy powder core, and thus, high current ripple and fluctuation. In this paper, we take into account this variation while designing controller and selecting key components to ensure inverter normal operation. Additionally, to adopt a cost-effective microcontroller for the inverter, the sensitivities of the control to various parameters are investigated and presented in this paper. Experimental results measured from a 5-kW single-phase prototype have verified the feasibility of the designed inverter. [ABSTRACT FROM PUBLISHER]