Search

A three-level converter is used as the power converters of wind turbine systems because of their advantages such as low-current total harmonic distortion, high efficiency, and low collector–emitter voltage. Interior permanent magnet synchronous generators (IPMSGs) have been chosen as the generator in wind turbine systems owing to their advantages of size and efficiency. In wind turbine systems consisting of the three-level converter and the IPMSG, fault-tolerant controls for an open-circuit fault of switches should be implemented to improve reliability. This paper focuses on the open-circuit fault of outer switches (Sx1 and Sx4) in three-level rectifiers (both neutral-point clamped and T-type) that are connected to the IPMSG. In addition, the effects of Sx1 and Sx4 open-circuit faults are analyzed, and based on this analysis, a tolerant control is proposed. The proposed tolerant control maintains normal operation with sinusoidal currents under the open-circuit fault of outer switches by adding a compensation value to the reference voltages. The effectiveness and performance of the proposed tolerant control are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

Open- and short-circuit faults are the most severe issues that affect the stability and reliability of power conversion systems. The space vector modulation (SVM) technique is widely used to control power converters. However, conventional SVM is incapable of controlling the system effectively when such faults occur. Considering these, this article proposes a modified SVM that is capable of tolerating the extreme cases of faults (including multi open-/short-circuit faults) simultaneously. An innovative fault tolerance method is proposed to tolerate multifaults in hybrid active neutral point converters (HANPCs). Furthermore, new voltage reference signals are created in addition to calculating voltage offset and inserting modified switching sequences. A descriptive performance analysis of the modified SVM technique is applied under healthy and faulty conditions. Correspondingly, the effects of the total harmonic distortion of the system performance are also highlighted and explained. The results reveal that the proposed control strategy can effectively maintain healthy and safe operation under faulty conditions without the need for additional parts or alteration of the topology configuration. In addition, the proposed method can be applied to HANPCs without special requirements to withstand high voltage levels. The effectiveness of the proposed method is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

Multilevel rectifier topologies are commonly used in wide-power range applications. The T-type rectifier topology, which is a three-level topology, has an advantage in terms of efficiency compared to a neutral-point clamped (NPC)-type topology. In applications using the T-type rectifier topology, improving reliability has gained increased attention recently. A tolerance control for T-type rectifiers is necessary to improve the reliability of applications. When an open fault of switches connected to the neutral-point occurs, the NPC-type rectifier cannot restore distorted input currents, on the other hand, the T-type rectifier can eliminate the input current distortion completely. In this paper, we report two studies: 1) a three-level switching-oriented tolerance control, which is advantageous in terms of efficiency, for the Sx2 and Sx3 open-switch faults of the T-type rectifier and 2) comparison of the proposed tolerance control with two existing tolerance controls. In particular, the current total harmonic distortion, dc-link voltage ripple, and switch losses of these tolerance controls are analyzed by using simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents an open-circuit fault detection method for a grid-connected neutral-point clamped (NPC) inverter system. Further, a fault-tolerant control method under an open-circuit fault in clamping diodes is proposed. Under the grid-connected condition, it is impossible to identify the location of a faulty switch by the conventional methods which usually use the distortion of outputs because the distortion of the outputs is the same in some fault cases. The proposed fault detection method identifies the location of the faulty switch and the faulty clamping diode of the NPC inverter without any additional hardware or complex calculations. In the case of the clamping diode faults, the NPC inverter can transfer full rated power with sinusoidal currents by the proposed fault-tolerant control. The feasibility of the proposed fault detection and the fault-tolerant control methods for the grid-connected NPC inverter are verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]