Search

This letter demonstrates an on-silicon integrated thin film coupled inductor using a novel cascade matrix concept to suit multiphase integrated voltage regulator (IVR) applications. The novel cascade matrix coupled (CMC) stripline inductor facilitates all-phase-coupled configuration to reduce the phase ripple current in IVRs. It also shows excellent scalability and neat floor planning. Moreover, the proposed CMC inductor uses double layer metal scheme for windings and interconnects, which significantly reduces the ac winding resistance. A four-phase CMC inductor has been successfully fabricated on-silicon substrate and characterized, which uses conventional thin film magnetic core deposition process to achieve in-plane magnetic uniaxial anisotropy. The device occupies 3.2 × 1.7 mm2 floor area and provides 19.5 nH phase inductance with 120 mΩ dc resistance. The saturation current for each phase is up to 0.4 A when the phase inductance drops by approximately 20%. The coupling coefficient between any two phases of the proposed CMC inductor is 0.27, much higher and more controllable than that of toroid core-based coupled inductors. [ABSTRACT FROM AUTHOR]

Coupled inductors offer significant advantages over their uncoupled counterparts; however, with these advantages come a number of additional design caveats. The factors affecting the design and optimization of coupled stripline microinductors for PwrSoC applications are outlined, which include device area, the number of coupled phases, duty cycle, paralleling of coupled inductors, switching frequency, as well as thermal and saturation constraints. Results of this analysis are presented and discussed along with guidelines for the design of coupled stripline microinductors, which show that paralleling coupled inductors is the best route toward higher output current. Analytical models predict a peak inductor efficiency of 86.8% and 86.3% for fabricated 3 and 5-phase coupled stripline microinductors with an Ni45Fe55 core, respectively. Models are verified by measurements on prototype 3 and 5-phase converters with parallel coupled stripline microinductors over a range of operating conditions. [ABSTRACT FROM AUTHOR]

In this paper, models that account for the duty cycle and phase shift angle of the applied phase voltages in coupled stripline microinductors are presented and are shown to have a significant impact on harmonic current amplitudes and therefore microinductor efficiency. The impact of a high coupling factor between two windings surrounded by a single core is also investigated. The models are validated using finite-element analysis and measurements. A three-phase-coupled microinductor has been fabricated with a Ni45Fe55 core and analyzed for a number of operating conditions. A prototype 1.6 W, three-phase converter utilizing this inductor has also been measured and is discussed in detail. The coupled microinductor is predicted to have a peak efficiency of 86.6% at 20 MHz in the prototype circuit. [ABSTRACT FROM AUTHOR]

Inductor-on-silicon research to date has focused on optimizing technologies for maximum power density and efficiency, with most design procedures based on computationally intensive methods. In this paper, a simple and intuitive method for designing microinductors based on a given dc–dc converter specification, which includes accurate models for all loss components, is presented. A detailed examination of variations in designs to realise the same circuit performance is presented. Finally, finite element analysis simulations demonstrating the accuracy of the models are given, along with measured results. [ABSTRACT FROM AUTHOR]

This paper presents the design of miniaturized bond wire transformers assembled with standard IC bonding wires and NiZn and MnZn ferrite toroidal cores. Several prototypes are fabricated on a printed circuit board substrate with various layouts in a 4.95\; mm \times 4.95\; mm area. The devices are modeled by analytical means and characterized with impedance measurements over a wide frequency range. Experimental results on 1:38 device show that the secondary self-inductance increases from 0.3 μH with air-core to 315 μH with ferrite core; the coupling coefficient improves from 0.1 with air-core to 0.9 with ferrite core; the effective turns ratio enhances from 0.5 with air-core to 34 with ferrite core. This approach is cost effective and enables a flexible design of efficient micromagnetics on top of ICs with dc inductance to resistance ratio of 70 μH/Ω and an inductance per unit area of 12.8 μH/mm2 up to 0.3 MHz. The design targets the development of bootstrap circuits for ultralow voltage energy harvesting. In this context, a low-voltage step-up oscillator suitable for thermoelectric generator sources is realized with a commercial IC and the proposed microtransformers. Experimental measurements on a discrete prototype report that the circuit bootstraps from voltages down to 260 mV and outputs a dc voltage of 2 V. [ABSTRACT FROM AUTHOR]

Microfabricated inductors experience increasing interest and research activity because of their high potential in buck converters for power supply in package and power supply on chip applications. This paper details the modeling and optimization of microfabricated racetrack inductors. The analytical expressions derived characterize inductance, efficiency, and power density based on geometrical parameters, inductor current, and switching frequency. An accurate analysis of the inductor current that includes the impact of losses is performed to determine the switching frequency, the ac copper losses, and the core losses. The presented model is compared to finite element method simulations and reported results of three microfabricated inductors. Finally, the optimum tradeoff between efficiency and power density is identified using the Pareto front, which results from the evaluation of a large number of microfabricated inductors in the design space defined by the application. [ABSTRACT FROM AUTHOR]

Thin-film Si-integrated inductors with closed cores have different magnetic field distributions in the winding window space compared to the inductors with unclosed cores. One-dimensional methods are no longer applicable for these inductors to calculate the ac resistance. Based on the analysis of the magnetic field distribution of the devices, a 2-D field solution was developed, which leads to an improved 2-D method to calculate the ac resistance of the device. High accuracy of this new approach has been verified by finite-element analysis, while 1-D methods can lead to significant errors. [ABSTRACT FROM AUTHOR]