Search

This article proposes a voltage-fed zero-voltage-switched topology based on the push–pull converter. The proposed converter uses the leakage inductance of the transformer to transfer power from input to output. Phase-shift modulation strategy is used to control the flow of this power. A coupled LC regenerative snubber-based energy recovery circuit reclaims the trapped energy in the leakage inductance. The snubber circuit also ensures soft-switched operation and reduces the voltage stress across the semiconductor switches. The power-flow equation is characterized and experimentally verified for the proposed converter. The gate control signals are implemented using an field-programmable gate array (FPGA). A 240-W prototype validates the steady-state behavior and snubber design equations. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

Inductor current is an important feedback parameter in synchronous buck converters (SBCs). It is used for overcurrent protection, current sharing among interleaved modules, and current-mode feedback regulation, among others. While implementing a digital controller, inductor current is sensed and fed into the controller through a high sampling frequency analog to digital converter (ADC). As the switching frequency of the converter becomes higher, the need for an even higher sampling frequency ADC also goes up, which is a distinct disadvantage in terms of the overall cost. This paper discusses a simple current estimation technique that avoids use of any expensive current sensor and high sampling frequency ADCs. The paper shows that in a buck converter, inductor current can be estimated by tracking the width of the switch node voltage. Implementation and limitations of the proposed current estimation scheme are discussed in detail. The proposed method is validated using a 3.3 V–15 A SBC prototype and results show the estimation technique is accurate within 5% with a converter switching frequency of 800 kHz. In order to prove the effectiveness of the technique in feedback regulation, the current estimation technique is used to implement average current mode and hysteretic current mode control on a SBC. To prove the effectiveness of the proposed current estimation scheme, it is used in closed-loop control of the SBC to verify the dynamic responses, such as start-up transient, step change in load, and reference. [ABSTRACT FROM AUTHOR]

Switched boost inverter (SBI) is a single-stage power converter derived from Inverse Watkins Johnson topology. Unlike the traditional buck-type voltage source inverter (VSI), the SBI can produce an ac output voltage that is either greater or less than the available dc input voltage. Also, the SBI exhibits better electromagnetic interference noise immunity when compared to the VSI, which enables compact design of the power converter. Another advantage of SBI is that it can supply both dc and ac loads simultaneously from a single dc input. These features make the SBI suitable for dc nanogrid applications. In this paper, the SBI is proposed as a power electronic interface in dc nanogrid. The structure and advantages of the proposed SBI-based nanogrid are discussed in detail. This paper also presents a dq synchronous-reference-frame-based controller for SBI, which regulates both dc and ac bus voltages of the nanogrid to their respective reference values under steady state as well as under dynamic load variation in the nanogrid. The control system of SBI has been experimentally validated using a 0.5-kW laboratory prototype of the SBI supplying both dc and ac loads simultaneously, and the relevant experimental results are given in this paper. The low cross regulation and the dynamic performance of the control system have also been verified experimentally for a 20% step change in either dc or ac load of SBI. These experimental results confirm the suitability of the SBI and its closed-loop control strategy for dc nanogrid applications. [ABSTRACT FROM AUTHOR]