Search

This paper proposes the predictive control with the discrete space-vector modulation (DSVM) for Vienna rectifier connecting to the permanent magnet synchronous generator (PMSG) of the wind turbine system (WTS). Since Vienna rectifier has the special operation principle, Vienna rectifier generates only the feasible eight voltage vectors, which can be a candidate vector for the predictive control, depending on the sign of the input currents. In the proposed predictive control, the feasible voltage vectors are extended from 8 to 19 consisting the 8 original voltage vectors and 11 virtual voltage vectors by using the DSVM for improving the current quality related to the torque ripple, vibration, and noise, and the neutral-point voltage balance with low voltage ripple is guaranteed by using the offset value calculated based on the model of two dc-link capacitors in Vienna rectifier. The scheme for reducing calculation burden is applied in selecting the candidate vector. In addition, the limited operation range for the maximum torque per ampere control of PMSG connected to Vienna rectifier is analyzed. The performance of the proposed predictive control with DSVM for Vienna rectifier with PMSGs is verified in simulation and experiment. [ABSTRACT FROM AUTHOR]

The nongenerative-boost type rectifier, which is called the Vienna rectifier, is advantageous in terms of efficiency and current total harmonic distortion. Therefore, the Vienna rectifier is used in grid-connected applications such as telecommunication systems and wind turbine systems. Owing to the structural characteristics of the Vienna rectifier, various switching methods exist. Among these methods, a carrier-based discontinuous pulse-width modulation (CB-DPWM) method guarantees high efficiency compared to continuous pulse-width modulation methods; moreover, it is simple compared to a DPWM method based on space vectors. In this paper, the performance of the CB-DPWM method, its applicable region depending on the power factor and modulation index (Ma ), and its efficiency are analyzed in detail. Then, based on the analysis, a neutral-point voltage balancing method for the CB-DPWM method is proposed. The effectiveness and performance of the proposed neutral-point voltage balancing method are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

A three-level converter is used as the power converters of wind turbine systems because of their advantages such as low-current total harmonic distortion, high efficiency, and low collector–emitter voltage. Interior permanent magnet synchronous generators (IPMSGs) have been chosen as the generator in wind turbine systems owing to their advantages of size and efficiency. In wind turbine systems consisting of the three-level converter and the IPMSG, fault-tolerant controls for an open-circuit fault of switches should be implemented to improve reliability. This paper focuses on the open-circuit fault of outer switches (Sx1 and Sx4) in three-level rectifiers (both neutral-point clamped and T-type) that are connected to the IPMSG. In addition, the effects of Sx1 and Sx4 open-circuit faults are analyzed, and based on this analysis, a tolerant control is proposed. The proposed tolerant control maintains normal operation with sinusoidal currents under the open-circuit fault of outer switches by adding a compensation value to the reference voltages. The effectiveness and performance of the proposed tolerant control are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

The purpose of neutral-point voltage balancing algorithms in the three-level neutral-point clamped (3L-NPC) topology is to eliminate the voltage unbalance of top- and bottom-side dc-link voltages (neutral-point voltage). These algorithms are divided into dc unbalance and ac unbalance compensation methods. The dc unbalance causes distortion of output currents; therefore, this problem has to be solved. The ac unbalance implies that there is an ac ripple in the top- and bottom-side dc-link voltages. In applications using 3L-NPC topology, a large dc-link capacitor value is required to mitigate this ac unbalance problem. As a result, the size and the cost of applications become large and expensive. In this paper, a compensation method for mitigating the ac unbalance of the neutral-point voltage is proposed, which causes the dc-link capacitor value to be small, when a carrier-based pulse width modulation method is applied. The proposed method compensates the ac unbalance of the neutral-point voltage by adding an optimal compensation value to the reference duty signals. This compensation value is calculated simply by currents and reference duty signals. The calculation process of the optimal compensation value is discussed, and the effectiveness of the proposed method is verified with simulations and experiments. [ABSTRACT FROM PUBLISHER]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]