Search

This article exhibits an output voltage-derivative observer-based output voltage-tracking technique for dc/dc boost converters without current feedback, taking the model-plant mismatches (caused by parameter and load variations) and model nonlinearity into consideration. In contrast to extant passivity-based approaches, the proposed solution includes observers to estimate the output voltage derivative and does not require exact model information, which offers a few features: converter parameter information-free output voltage-derivative observers including the modified disturbance observation algorithm for improving the high-frequency disturbance rejection capability as a replacement of the estimation error integral actions, and the observer-based output voltage and its derivative error stabilizer with a damping adaptation mechanism assigning the desired energy function to the closed-loop system. Experimental verification is provided to demonstrate the practical advantages of the proposed solution using a 3-kW bidirectional converter. [ABSTRACT FROM AUTHOR]

Three-level neutral-point-clamped (3L-NPC) voltage source inverters are widely used in many low- and medium-power applications. However, the 3L-NPC inverter has an inheritance issue of the neutral-point (NP) voltage unbalancing due to the deviation of dc-link capacitor voltages causing distortions for the output waveform quality. Generally, discontinuous pulsewidth modulation (DPWM) is used to diminish the stress on power transistors and prolong their lifespan, however; it is not capable of solving the issue of NP voltage unbalancing. Therefore, this article proposes a simple voltage balancing control based on DPWM with a hysteresis NP voltage band. The balancing control method is only activated once the capacitance voltage error exceeds the hysteresis band by generating a momentary offset on the opposite direction of the DPWM offset. In this way, both top and bottom capacitance voltages will converge within a predefined error band. Various hysteresis error bands are investigated by analyzing the power losses, total harmonic distortions, and common mode voltage. The advantages of this proposed method are its simplicity and ease of control while maintaining the features of DPWM. The effectiveness of the proposed method is validated using simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes the predictive control with the discrete space-vector modulation (DSVM) for Vienna rectifier connecting to the permanent magnet synchronous generator (PMSG) of the wind turbine system (WTS). Since Vienna rectifier has the special operation principle, Vienna rectifier generates only the feasible eight voltage vectors, which can be a candidate vector for the predictive control, depending on the sign of the input currents. In the proposed predictive control, the feasible voltage vectors are extended from 8 to 19 consisting the 8 original voltage vectors and 11 virtual voltage vectors by using the DSVM for improving the current quality related to the torque ripple, vibration, and noise, and the neutral-point voltage balance with low voltage ripple is guaranteed by using the offset value calculated based on the model of two dc-link capacitors in Vienna rectifier. The scheme for reducing calculation burden is applied in selecting the candidate vector. In addition, the limited operation range for the maximum torque per ampere control of PMSG connected to Vienna rectifier is analyzed. The performance of the proposed predictive control with DSVM for Vienna rectifier with PMSGs is verified in simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper proposes the new clamping angle control (CAC) pulse width modulation (PWM) method to restore its maximum linear modulation range of voltage source inverters (VSIs) reduced by the duty ratio limitation in hardware implementation, which makes the VSIs to operate nonlinearly in the high modulation range. The deadtime and the bootstrap gate driver circuit mainly cause this duty ratio limitation in practice. In particular, the bootstrap gate driver circuit is used in many industrial applications by avoiding the additional power supply to apply the gate-source voltage of power switches, and therefore making the VSIs to be small size with the low cost. First, the proposed CACPWM method is theoretically analyzed. Then, it is applied in the high modulation range to overcome the limitation of the duty ratio due to the use of the bootstrap gate driver circuit. Thereafter, its practical effectiveness is verified by both simulation and experimental tests. Also, the resulting harmonic distortions are compared with those by the conventional PWM methods. [ABSTRACT FROM AUTHOR]

The nongenerative-boost type rectifier, which is called the Vienna rectifier, is advantageous in terms of efficiency and current total harmonic distortion. Therefore, the Vienna rectifier is used in grid-connected applications such as telecommunication systems and wind turbine systems. Owing to the structural characteristics of the Vienna rectifier, various switching methods exist. Among these methods, a carrier-based discontinuous pulse-width modulation (CB-DPWM) method guarantees high efficiency compared to continuous pulse-width modulation methods; moreover, it is simple compared to a DPWM method based on space vectors. In this paper, the performance of the CB-DPWM method, its applicable region depending on the power factor and modulation index (Ma ), and its efficiency are analyzed in detail. Then, based on the analysis, a neutral-point voltage balancing method for the CB-DPWM method is proposed. The effectiveness and performance of the proposed neutral-point voltage balancing method are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

A three-level converter is used as the power converters of wind turbine systems because of their advantages such as low-current total harmonic distortion, high efficiency, and low collector–emitter voltage. Interior permanent magnet synchronous generators (IPMSGs) have been chosen as the generator in wind turbine systems owing to their advantages of size and efficiency. In wind turbine systems consisting of the three-level converter and the IPMSG, fault-tolerant controls for an open-circuit fault of switches should be implemented to improve reliability. This paper focuses on the open-circuit fault of outer switches (Sx1 and Sx4) in three-level rectifiers (both neutral-point clamped and T-type) that are connected to the IPMSG. In addition, the effects of Sx1 and Sx4 open-circuit faults are analyzed, and based on this analysis, a tolerant control is proposed. The proposed tolerant control maintains normal operation with sinusoidal currents under the open-circuit fault of outer switches by adding a compensation value to the reference voltages. The effectiveness and performance of the proposed tolerant control are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper proposes a power predictive control (PPC) method for three-phase pulse width modulated rectifiers without a proportional-integral controller. The proposed PPC method calculates the optimized voltage vector by analyzing the relationship between the virtual flux, active power, converter voltage, and filter parameters. Thus, an overshoot does not occur and the fast and accurate power control becomes possible. The predictive algorithm computes the power error that would be produced by applying each vector and selects the one that contributes the minimum error. The simulation and experimental results prove that the proposed method provides an excellent steady-state performance and quick dynamic response. [ABSTRACT FROM PUBLISHER]

The purpose of neutral-point voltage balancing algorithms in the three-level neutral-point clamped (3L-NPC) topology is to eliminate the voltage unbalance of top- and bottom-side dc-link voltages (neutral-point voltage). These algorithms are divided into dc unbalance and ac unbalance compensation methods. The dc unbalance causes distortion of output currents; therefore, this problem has to be solved. The ac unbalance implies that there is an ac ripple in the top- and bottom-side dc-link voltages. In applications using 3L-NPC topology, a large dc-link capacitor value is required to mitigate this ac unbalance problem. As a result, the size and the cost of applications become large and expensive. In this paper, a compensation method for mitigating the ac unbalance of the neutral-point voltage is proposed, which causes the dc-link capacitor value to be small, when a carrier-based pulse width modulation method is applied. The proposed method compensates the ac unbalance of the neutral-point voltage by adding an optimal compensation value to the reference duty signals. This compensation value is calculated simply by currents and reference duty signals. The calculation process of the optimal compensation value is discussed, and the effectiveness of the proposed method is verified with simulations and experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes a simple and effective method to reduce torque ripples for the torque predictive control (TPC) of permanent-magnet synchronous motors (PMSMs). The conventional TPC analyzes the relationship among the electrical torque, stator flux, and stator voltage using the magnitude of the stator voltage vector of PMSMs to obtain the angle of the reference voltage vector and accurately control the torque. In addition, the stator-flux control uses the hysteresis method. However, the voltage vector that can be chosen in an inverter is limited because the conventional TPC fixes the magnitude of the reference voltage vector, and thus, a large torque ripple is generated in the low-speed region. The proposed TPC does not fix but varies the magnitude of the reference voltage vector using both the torque and flux error information. Therefore, it not only has the fast dynamic of a direct torque control but also can reduce effectively the torque ripple. The proposed method is proven by the simulation and experimental results, and the proposed algorithm provides an excellent steady-state response and fast dynamics. [ABSTRACT FROM AUTHOR]

The magnitude of hysteresis torque band has a considerable effect on the performance of two-level direct torque control (DTC) of induction machines. The conventional DTC fails at low speed due to the poor flux regulation. In this paper, two dynamic hysteresis torque band (DHTB) strategies for the conventional DTC are proposed to solve this problem by dynamically altering the amplitude of hysteresis torque band based on a flux error range. In this way, the simplicity of DTC algorithm is retained since it only requires a minor modification on its structure. The paper also presents further analysis on flux degradation, particularly the droop in between the flux sectors. In addition, the switching frequency effect of reverse voltage vectors for both DHTB schemes is investigated on the performance of the speed-sensorless DTC drive. The effectiveness of the proposed schemes is confirmed by simulation and experimental validation. Results show a significant enhancement in the flux regulation and dynamic torque response from zero motor speed. [ABSTRACT FROM AUTHOR]

This paper proposes a simple control method of induction motors (IMs) with improved dynamic response and steady-state performance by using a model-based predictive control algorithm. The predictive torque control (PTC) method analyzes the relationship between the electrical torque and stator voltage of IMs by using the stator voltage vector magnitude to obtain the reference voltage vector angle and accurately control the electrical torque. However, the conventional PTC method has a fixed reference voltage vector magnitude and thus has a large torque ripple in the steady state and slow dynamics in the transient state. The proposed PTC method is based on mathematical equations, which allow minimization of torque error and calculation of a relevant reference voltage to establish a better dynamic response in the transient state and accurate control performance in the steady state. Excellent steady-state performance and a quick dynamic response of the proposed method are proved by the simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]