Search

In this paper, we analyze the existence and stability of equilibrium of dc micro-grids under the master-slave control (where some distributed generations (DGs) are under droop control with dual-loop (Droop-DGs) and some DGs are under MPPT control (MPPT-DGs)). Firstly, the power-flow equation of the dc micro-grids under master-slave control with CPLs is obtained. Then, we transform the solvability of the power-flow equation into the existence of a fixed point for a contraction mapping. Based on Banach's fixed point theorem, a sufficient condition to guarantee the existence of the power-flow solution in dc micro-grids is derived. The condition derived in this paper is not only useful for master-slave control but also for droop control. Besides, to calculate the power-flow solution, an iterative algorithm with exponential convergence rate is proposed. Secondly, we use a singular perturbation model to predict the qualitative behavior of the system near the equilibrium point. By analyzing eigenvalues of the boundary layer system and reduced-order system Jacobian matrix, the robust stable analytic conditions of the system are obtained. The effect of the sampling delay on the system stability is analyzed, the robust stability condition is obtained by using linear matrix inequality. The simulation results verify the correctness of the proposed conditions. The obtained conditions provide a reference for establishing a reliable dc micro-grid. [ABSTRACT FROM AUTHOR]

The paper proposes a control scheme to improve the dynamic response of power systems through the automatic regulators of converter-based Distributed Energy Resources (DERs). In this scheme, both active and reactive power control of DERs are varied to regulate both frequency and voltage, as opposed to current practice where frequency and voltage controllers are decoupled. To assess the proposed control against the current state-of-art, the paper also defines a metric that captures the combined effect of frequency/voltage response at any given bus of the network. Results indicate that the proposed control strategy leads to a significant improvement in the stability and performance of the overall power system. These results are based on a comprehensive case study carried out by employing a modified version of the IEEE 39-bus benchmark system, where a portion of the synchronous machines is substituted by converter-interfaced DERs. The impact on the proposed control of load models, the $R/X$ ratio of network lines, as well as the level of DER penetration to the grid, are properly evaluated and conclusions are duly drawn. [ABSTRACT FROM AUTHOR]

A Hybrid AC/DC microgrid (MG) can integrate distributed generation sources and distributed loads on the AC and DC side of the MG by eliminating many unnecessary power conversion devices, which is more flexible and efficient. However, to achieve reliable and economic operation of a hybrid AC/DC MG is challenging due to its complex structure. In this paper, a novel distributed event-triggered hierarchical control strategy is proposed to improve the economic operation of a hybrid AC/DC MG. For the primary control, distributed local controls of AC DGs, DC DGs, and interlinking converters (ICs) are realized by adopting the droop control method. For the secondary control, the distributed economic dispatch, distributed average bus voltage discovery, and distributed proportional power-sharing algorithms are first proposed; then, control objectives of voltage and frequency restoration and economic operation of the hybrid AC/DC MG are realized based upon the developed algorithms. Furthermore, the distributed secondary control is built upon an event-triggered mechanism developed in this paper, which can reduce the communication burden. The simulation results demonstrate the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Droop control is a viable method for the operation of island DC microgrids in a decentralized architecture. This paper presents a mixed-integer conic optimization formulation for the design of generator droop control, comprising the parameters of a piecewise linear droop curve. The mixed-integer formulation originates from a stochastic optimization framework that considers several operating scenarios for finding the optimal design. The convexity of the mixed-integer problem continuous relaxation gives global optimality guarantees for the design problem. The paper presents computational results using a tight polyhedral approximation of the conic program, leading to a mixed-integer linear programming (MILP) problem that is solved using a state-of-the-art commercial solver. The results from the proposed approach are contrasted with both a classic linear droop control design and a recent piecewise linear formulation. The Monte-Carlo simulation results quantify the extent to which the MILP solution is superior in reducing voltage violations and power loss, and the degree to which the loss is close to that from a conic optimal power flow solution. [ABSTRACT FROM AUTHOR]

This paper proposes a market framework to approach economic dispatch as a subproblem in smart distribution systems. Four subproblems are associated with four different submarkets (SMs) in the presented framework. Market participants are eligible to bid in different submarkets based on the type of their distributed generation (DG) unit. To effectively tackle the conflicts among objective functions of different submarkets, the corresponding formulated subproblems are assigned to two different agents, namely distribution system operator (DSO) and a green bank agent (GBA). A communication mechanism is designed within the proposed framework such that DSO and GBA compromise their solutions and find a tradeoff to reasonably address the concerns of the four subproblems within SMs 1-4. The effectiveness of the proposed market framework is validated on a well-known 136-bus distribution system, which is modified to contain wind turbine DG aggregators, photovoltaic DG aggregators, and diesel-engine DG aggregators. [ABSTRACT FROM AUTHOR]

Voltage regulation and proper load-sharing are two main control objectives of DC microgrids which the consensus-based secondary control can be regarded as a feasible approach to achieve them. Using this approach, in addition to the stable voltage regulation, the load is shared according to the nominal potential of the distributed generation units. Nevertheless, the conventional consensus-based secondary control uses the time-triggered communication paradigm that leads to a high communication burden due to transmitting and receiving unnecessary data. In this paper, to prevent excessive data-exchanging, the mentioned approach is upgraded with a novel event-triggered scheme. The system stability analysis under the suggested event-triggered secondary controller is assessed using the Lyapunov theorem. Furthermore, the Zeno-freeness feature of the proposed solution is mathematically proved after assessing uniformly ultimately bounded stability and extracting the current per-unit and voltage derivatives dynamic as the consensus algorithm’s external inputs. The proposed approach is applied to a DC microgrid, and its performance is validated under different scenarios using Simulink/MATLAB environment. Moreover, the experimental tests prove the merits of the suggested method. [ABSTRACT FROM AUTHOR]

Volt/VAr Optimization (VVO) is becoming increasingly crucial in distribution management systems with renewable sources that require setting their reactive power in coordination with legacy voltage and reactive power control devices. This paper presents a VVO method that operates in complex variables based on the Wirtinger calculus; it employs a penalty method that keeps voltage magnitudes and controller parameters within limits together with a probabilistic rounding technique for handling switched device variables. The complex variable implementation permits using the compensation technique when solving the Karush-Kuhn Tucker (KKT) system, thus achieving a significant speedup due to limiting the number of linear system factorizations. The proposed method is contrasted with a classical VVO implementation employing discrete coordinate search from the current operating point and an enhanced version that uses sensitivity information. Numerical results on distribution networks having up to 3147 nodes show that the proposed method is significantly faster than classical methods and gives operating points free of voltage magnitude violations and lower power loss. [ABSTRACT FROM AUTHOR]

The high-precision parameters in distribution networks are difficult to obtain, which brings difficulties to the model-based methods and analysis. With the widespread deployment of high-precision measurement units, data-driven methods have greater advantages in practice. In addition, with massive integration of distributed renewable generation and fast electric vehicle chargers, the fluctuations of net load increase significantly. The data-driven power flow calculation method based on the linear model becomes difficult to obtain accurate results for the low nonlinear adaptability. To improve the data-driven power flow calculation accuracy under high penetration of renewable distribution generation, this paper proposed an approach with high adaptability to the nonlinearity of power flow. Based on the thought of Koopman operator theory, the nonlinear relationship in power flow calculation is converted into a linear mapping in a higher dimension state space, which can significantly improve the calculation accuracy. Case studies on different IEEE cases have demonstrated that the proposed method can realize higher accuracy in power flow calculation with large-scale power fluctuations, compared to the existing data-driven method, in both mesh and radial networks. Finally, measurement data of a practical 10kV distribution network has been further used to verify the effectiveness of the proposed method in practical applications. [ABSTRACT FROM AUTHOR]

This paper proposes a distributed coordinated voltage control scheme for distribution networks with distributed generation (DG) and on-load tap changer (OLTC). In this scheme, static synchronous compensators (STATCOMs), DG units and OLTC are coordinated to regulate voltages of all buses to be close to the nominal value in the distribution network, mitigate voltage fluctuations, and minimize the number of operations of OLTC while considering different temporal characteristics of voltage regulation devices. The optimization problem of coordinating DG units and STATCOMs is decomposed by the gradient projection (GP) method. The local controller optimizes the reactive power outputs of DGs and STATCOMs according to local voltage and reactive power measurements, and still achieves the optimal coordination of DG units and STATCOMS in a decentralized manner without a central controller or communication between local controllers. The OLTC control scheme is designed to correct the long-term voltage deviations based on model predictive control (MPC) while minimizing the number of operations. The local controllers send the calculated reactive power references of DG and STATCOMs to the OLTC controller, which achieves distributed coordinated voltage control and mitigates the computation burden. A distribution network with two 20 kV feeders and 8 DG units was used to validate the control performance of the proposed coordinated voltage control scheme. [ABSTRACT FROM AUTHOR]

The occurrence of large-scale outages in power distribution systems (PDSs) caused, for instance, by extreme weather events has raised concerns on the cascading impact of the power outages on the resilience of other critical infrastructures, including water distribution systems (WDSs), whose healthy operation highly relies on the availability of power from PDSs. This paper proposes an analytics model for quantifying the interdependence between the resilience of power and water distribution systems. The proposed model first performs spatio-temporal outage analysis on the PDS and WDS to determine the PDS power serving capability and the resulting cascading impact on the WDS water serving capability during the occurrence of disruptions. The resilience interdependence is then determined by a proposed set of six metrics calculated using the power and water serving capability profiles, which trace and quantify the cascading impacts of power outages in the operation of WDSs during the degradation and recovery stages. The proposed analytics model is implemented on the IEEE 33-bus power distribution system supplying power for pumping stations of a 15-node test WDS, considering multiple cases of water storage capacity, single and multiple outage scenarios, and availability of distributed generation. The numerical results demonstrate that the proposed metrics track the temporal and spatial interdependence between the resilience of power and water distribution systems, providing a mechanism to identify weak spots, and assess options to enhance the resilience of the critical water infrastructure. [ABSTRACT FROM AUTHOR]

Power system planning is essential for ensuring development of a safe and stable power system. Articles on power system planning have been published in recent decades. In this paper, bibliometric analysis is applied to power system planning to identify its basic characteristics, and to summarize the research hotspots and trends. A total of 4562 publications were obtained from the Web of Science during 1971–2020. The 4562 publications cover 8136 keywords, 1526 journals, 107 countries/territories, and 2519 institutions. IEEE Transactions on Power Systems is the key journal in power system planning; USA, China, and England are the countries that dominate publication production. Research hotspots and trends were analyzed using author-keyword co-occurrence analysis and keyword burst detection. Four clusters were identified and topics from Cluster I (central nodes as power system stability and transient stability) and Cluster IV (central nodes as power system simulation and economics) are important for power system planning research. However, their relative popularities have declined over the past two decades. This indicates that Cluster II (central nodes as renewable energy, wind power, and energy storage) and Cluster III (central nodes as distributed generation and smart grids) will be the focus of future research. [ABSTRACT FROM AUTHOR]

Soft open points (SOPs) are power electronic devices which provide interconnection between two feeders in place of normally open points in electricity distribution networks. SOPs can continuously control active power flow between feeders and inject reactive power controllably at both nodes, which can be used to provide substantial capacity support to the system. This paper provides a reliability-based method to quantify the capacity value (the additional load which can be accommodated without reducing reliability) of SOPs using the Effective Load Carrying Capability method within a Monte Carlo Simulation (MCS). Optimization of post-fault active/reactive power injections by SOPs to minimize energy not supplied is formulated (directly in matrix form) as a second-order cone programming problem. This results in very low computational times which enables embedding of the optimization problem within the MCS. The proposed methodology is applied to a modified real-world distribution network considering three different SOP sizes (5 SOPs totalling 2.5, 5, 10 MVA) across three redundancy levels (N-1, N-0.75, N-0.5), and on an unbalanced network with distributed generation. Results demonstrate capacity values ranging from 2.4–12.84 MVA. When operating under a relaxed redundancy level, the capacity value of a given SOP capacity can more than double relative to N-1. [ABSTRACT FROM AUTHOR]

The Virtual Power Plant (VPP) has been proposed to aggregate Distributed Generations (DGs) to act like a single power plant, thus, also has functions on the frequency and voltage support. The previous models of the VPP are static and focus on the energy trading and management. For the system transient response analysis, a dynamic VPP model must be needed. The paper proposes a reduced-order yet accurate aggregated model to represent VPP transients for the stability analysis of power systems. The goal is to provide a model that is adequate for system studies and can serve to the Transmission System Operator (TSO) to evaluate the impact of VPPs on the overall grid. The proposed model can accommodate the transient response of the most relevant controllers included in the distributed generators that compose the VPP. Using a comparison with a real-time detailed Electro-Magnetic Transients (EMT) models of the VPP confirms the validity of the proposed aggregated model. The case studies based on the IEEE 39-bus system verifies the accuracy of the proposed aggregated model on the system stability analysis. [ABSTRACT FROM AUTHOR]

To analyze the grid integration effect of a virtual synchronous generator (VSG), this paper proposes a simple power system modeling method. It is shown that for a specific disturbance, by simplifying the original network to a radical n generators single-load model, its state-space small-signal model can be obtained using a unified formula, as long as the single generator infinite bus model of each generator is given. Case studies based on the IEEE 9-bus test system as well as the New York New England test system show high efficiency of the proposed modeling to represent slow power and frequency deviations. Modal analyses give insight into how system poles are synthesized by individual generator poles, and how different designs of VSGs affect the system oscillation modes. Potential errors due to the topology simplification and the measures to avoid them are discussed. The time-domain results and modal analyses highlight some important features of VSG, which are overlooked in previous studies. [ABSTRACT FROM AUTHOR]

This work proposes a strategy that estimates the maximum distributed generation (DG) capacity that can be connected to the electric distribution system (EDS), when EDS upgrading actions are implemented. The problem is viewed from the distribution system operator (DSO) perspective and is formulated as a multiobjective optimization model that maximizes the DG capacity and minimizes the upgrading cost. Upgrading options include allocation of voltage regulators (VRs) and conductor replacement, which are coordinated with the application of generation curtailment, DG reactive power support, and voltage control using VRs. The uncertainty and variability of demand and DG power production are accounted for resorting to a multi-period robust formulation. The problem solution generates a set of upgrading plans, from which the DSO can select the one that meets its economic expectation and provides the EDS with the necessary capacity to accommodate the expected new DG. A post-optimization analysis is proposed to evaluate the impact of EDS upgrading on the DSO profit. Simulations are performed on a 135-bus EDS, and results show that the proposed strategy reveals an upgrading plan that increases the DG capacity up to 64.39% with a gain in the DSO profit of 5.43%, compared to the case without EDS upgrading. [ABSTRACT FROM AUTHOR]

In this letter, a simplified voltage sensitivity analysis technique that can provide accurate estimates of voltage change across the network for a given change in bus power injections in a three-phase unbalanced distribution network is proposed. This technique is derived from the first-order approximation of the Neumann series, which allows maintaining the accuracy of the solution while the computational effort is reduced. The proposed technique is tested on a 559-bus unbalanced distribution system with multiple distributed generation resources. The results show that the average error in the voltage estimates with the proposed method is not more than 0.3% with the execution time of similar order relative to the state-of-the-art sensitivity analysis methods. [ABSTRACT FROM AUTHOR]

Real-time detection of the microgrid stability is crucial for determining and adjusting the power-sharing droop control's gains to maintain a sufficient stability margin. Maintaining minimum relative stability should be ensured at different operating conditions to accommodate sudden system changes. This article develops a novel subspace-based identification technique to assess microgrid stability in real-time without relying on offline analytical small or large-signal models. Unlike conventional system identification techniques that require the introduction of external excitation (signal probing, load switching, or contingency event), the proposed method employs a simple internal routine through small and short-duration perturbations in the active power droop gain of inverter-based distributed generation (IBDG). The use of subspace identification does not require pre-defining the system's order, avoids the exhaustive computations associated with iterative identification methods and can handle a change of microgrid's network configuration. The proposed stability assessment method has been tested on an IBDG microgrid considering different operating conditions in MATLAB/Simulink. The accuracy of the proposed real-time stability assessment tool is determined by comparing the results to the analytically-derived small-signal model as well as the Matrix pencil and Prony methods. [ABSTRACT FROM AUTHOR]

Dispatching a fleet of distributed energy resources (DERs) in response to wholesale energy market or regional grid signals requires solving a challenging disaggregation problem when the DERs are coupled within a distribution network. This manuscript presents a computationally tractable convex inner approximation for the optimal power flow (OPF) problem that quantifies a feeder’s aggregate DERs hosting capacity and enables a realtime, grid-aware control policy for DERs in radial distribution networks. The inner approximation is derived by considering convex envelopes on the nonlinear terms in the AC power flow equations. The resulting convex formulation is then used to derive provable nodal injection limits, such that any combination of DER dispatches within their respective nodal limits is guaranteed to be AC admissible. These nodal injection limits are then used to construct a realtime, open-loop control policy for dispatching DERs at each location in the network to deliver fast grid services in aggregate. The IEEE-37 distribution network is used to validate the technical results and illustrate use cases. [ABSTRACT FROM AUTHOR]