Search

With the increasing penetration of renewable energy, accurate and efficient probabilistic optimal power flow (POPF) calculation becomes more and more important to provide decision support for secure and economic operation of power systems. This paper develops a novel nonparametric probabilistic optimal power flow (N-POPF) model describing the probabilistic information by quantiles, which avoids any parametric probability distribution assumptions of random variables. A novel critical region integral method (CRIM) which combines the multiparametric programming theory and discrete integral is proposed to efficiently solve the N-POPF problem. In the CRIM, the critical region partitioning algorithm is firstly introduced into the POPF model to directly establish the mapping relationship from wind power to optimal solutions of the POPF problem. Besides, a discrete integral method is developed in the CRIM to achieve the probability convolution calculation based on quantiles. Comprehensive numerical experiments verify the superior performance of the proposed CRIM in estimation accuracy and computational efficiency, and demonstrate that N-POPF model significantly improves the accuracy of uncertainty analysis. In general, the proposed N-POPF model and CRIM form a new framework of POPF problem for power system analysis and operation. [ABSTRACT FROM AUTHOR]

The reduced inertia levels in low-carbon power grids necessitate explicit constraints to limit frequency’s nadir and rate of change during scheduling. This can result in significant curtailment of renewable energy due to the minimum generation of thermal plants that are needed to provide frequency response (FR) and inertia. Additional consideration of fast FR, a dynamically reduced largest loss and under frequency load shedding (UFLS) allows frequency security to be achieved more cost effectively. This paper derives a novel constraint from the swing equation to contain the frequency nadir using all of these services. The expected cost of UFLS is found probabilistically to facilitate its comparison to the other frequency services. We demonstrate that this constraint can be accurately and conservatively approximated for moderate UFLS levels with a second order cone (SOC), resulting in highly tractable convex problems. Case studies performed on a Great Britain 2030 system demonstrate that UFLS as an option to contain single plant outages can reduce annual operational costs by up to $\pounds $ 559 m, 52% of frequency security costs. The sensitivity of this value to wind penetration, abundance of alternative frequency services, UFLS amount and cost is explored. [ABSTRACT FROM AUTHOR]

Power systems are facing the challenges of integrating massive electric vehicles (EVs) and lacking operational flexibility. An optimal and efficient coordination strategy is needed to coordinate the operations among EV charging stations (CSs) and the distribution system operator (DSO) and to make full use of the EVs’ charging flexibility for improving the operational flexibility of power systems. To this end, this paper proposes a CSs-DSO distributed coordination strategy. The proposed strategy integrates a supply-curve-based quantification method to quantify the EVs’ flexibility contribution and a Nash bargaining game-theory-based peer-to-peer (P2P) transactions model for maximizing the profits of entities participating in the coordination. To tackle the CSs-DSO coordination problem that has a bi-level-parallel coupling structure, an analytical target cascading (ATC) and alternating direction method of multipliers (ADMM) jointly-based distributed solution approach is proposed. First, the CSs-DSO bi-level model is decoupled by ATC with tie-line power being the only exchanged information; then, the model is further decomposed for each CS by ADMM for protecting the CSs’ privacy and autonomy. The effect of coordination and the computational efficiency of the proposed strategy is verified by numerical simulations on a modified IEEE 33-bus distribution system connecting multiple CSs. [ABSTRACT FROM AUTHOR]

In this paper, a novel distributed control strategy addressing a (feasible) psycho-social-physical welfare problem in islanded Direct Current (DC) smart grids is proposed. Firstly, we formulate a (convex) optimization problem that allows prosumers to share current with each other, taking into account the technical and physical aspects and constraints of the grid (e.g., stability, safety), as well as psycho-social factors (i.e., prosumers’ personal values). Secondly, we design a controller whose (unforced) dynamics represent the continuous time primal-dual dynamics of the considered optimization problem. Thirdly, a passive interconnection between the physical grid and the controller is presented. Global asymptotic convergence of the closed-loop system to the desired steady-state is proved and simulations based on collected data on psycho-social aspects illustrate and confirm the theoretical results. [ABSTRACT FROM AUTHOR]

In order to reduce the dependence on accumulated experience that is difficult to replicate for the human dispatchers to make power generation scheduling more automatically, quickly, and intelligently, higher requirements are placed on the level of the auxiliary decision-making system. In this paper, a short-term scheduling problem was treated as a regression task that concentrates on how to learn a reliable statistic model that concludes the intrinsic logic of the dispatching policy from extensive historical dispatching experience. In this way, since Kullback-Leibler distance can better measure the distance between two distributions, we designed a novel GAN-based learning method for the scheduling task. Also, we proposed a feasible framework that combines the stage of learning, decision-making, and deployment to support the practical implementation of the proposed algorithm. In the experiment, a real case that takes short-term scheduling tasks on a regional large-scale power system is considered in our experiments. As a result, the comparison of several methods further shows the superiority of the proposed GAN-based method under our implementations. [ABSTRACT FROM AUTHOR]

This paper proposes a novel modeling framework and decomposition-based solution strategy combining stochastic programming (SP) and robust optimization (RO) to deal with multiplex uncertainties in coordinated mid- and long-term power system planning. The problem is formulated as a multi-year generation and transmission planning problem from an independent system operator (ISO)’s perspective to minimize both expansion and operational costs under binary and continuous uncertainties, ${\bf i.e.}$ , system component contingency and load/generation variation. N- $\bf {k}$ contingencies are captured in RO using the reformulated contingency criteria, while the load/generation uncertainty is considered in SP embedded with RO using operating scenarios generated from the historical data with spatiotemporal correlations. The original hybrid model is highly intractable, but the intractability can be relieved by the proposed decomposition strategy based on the column-and-constraint generation and L-shaped algorithms. We apply our model to perform long-term system planning under extremely high renewable penetration and investigate the case of 100% renewables in long-term planning. Numerical experiments on multi-scale test systems verify the efficacy of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper presents a methodology for the design of over-frequency containment schemes in low inertia, high renewable systems. This methodology is demonstrated through the comprehensive redesign of the containment scheme for significant over-frequency events (e.g., the loss of an exporting HVDC interconnector) in the Ireland and Northern Ireland power system (All-Island System). The new scheme allows an existing synchronous generator runback system integrity protection scheme to be replaced with fixed wind tripping and dynamic response from wind. This exploits the capabilities of renewable generation to create effective protection and control resources. The methodology provides the steps required to determine the key parameters of the scheme (e.g., maximum allowable frequency, required volume of tripping, lowest trip frequency). A key consideration of the methodology is the volume of dynamic response from wind that can be deployed before frequency limits are violated (e.g., inertia and wind penetration). Dynamic simulations are performed in DSE Tools for the All-Island system considering a 2020 operational scenario. These simulations support the application of the methodology and demonstrate the effectiveness of the scheme designed for the All-Island system. [ABSTRACT FROM AUTHOR]

The fast development of renewable energies leads to an increase in the power electronics penetration in transmission systems. This is particularly true if one considers a 100% renewable energies power system, where wind and solar photovoltaic energies, which make most of the renewable energies connections today, are connected to the grid through power electronics converters. Because power electronics-based generators and synchronous machines-based generators have very different dynamic behaviours, some approximations usually used to run transient simulations of transmission systems might not be optimal for future grids. The systematic use of the phasor approximation applied to the power lines, implemented in most of the Transient Simulation Programs, is indeed not relevant any more. To avoid the use of Electromagnetic Transient simulations, that are resource-demanding and time-consuming, this paper presents a novel Model Order Reduction technique for large grids with a high penetration of power electronic devices. Compared to the classical phasor approximation, this event-based state residualization approximation allows accurate transient simulations and at the same time an optimal reduction of the number of the system’s state variables depending on the observed variables, the considered events and the tolerated approximation error. [ABSTRACT FROM AUTHOR]

Short-term load forecasts are needed for the efficient management of power systems. Although weather-based modeling is common, univariate models can be useful when the lead time of interest is less than one day. A class of univariate methods that has performed well with intraday data is exponential smoothing. This paper considers five recently developed exponentially weighted methods that have not previously been used for load forecasting. These methods include several exponential smoothing formulations, as well as methods using discount weighted regression, cubic splines, and singular value decomposition (SVD). In addition, this paper presents a new SVD-based exponential smoothing formulation. Using British and French half-hourly load data, these methods are compared for point forecasting up to one day ahead. Although the new SVD-based approach showed some potential, the best performing method was a previously developed exponential smoothing method. A second empirical study showed the better of the univariate methods outperforming a weather-based method up to about five hours ahead, with a combination of these methods producing the best results overall. [ABSTRACT FROM PUBLISHER]

There is a growing need for new optimization methods to facilitate the reliable and cost-effective operation of power systems with intermittent renewable energy resources. In this paper, we formulate the robust AC optimal power flow (RAC-OPF) problem as a two-stage robust optimization problem with recourse. This problem amounts to a nonconvex infinite-dimensional optimization problem that is computationally intractable, in general. Under the assumption that there is adjustable generation or load at every bus in the power transmission network, we develop a technique to approximate RAC-OPF from within by a finite-dimensional semidefinite program by restricting the space of recourse policies to be affine in the uncertain problem data. We establish a sufficient condition under which the semidefinite program returns an affine recourse policy that is guaranteed to be feasible for the original RAC-OPF problem. We illustrate the effectiveness of the proposed optimization method on the WSCC 9-bus and IEEE 14-bus test systems with different levels of renewable resource penetration and uncertainty. [ABSTRACT FROM AUTHOR]

In this paper, a new systematic method is proposed to analyze the system frequency in power systems under uncertain variability (UV). UV gradually increases in power systems, which originates from the renewable energy generation, random loads, frequency measurement, and communication channels, exerting noteworthy impacts on dynamic system frequency. The UV is modeled as a stochastic process in this paper. Then, the stochastic differential equations are used to describe the dynamic system frequency response (SFR) of a power system under UV, which is based on the SFR model. To assess system frequency dynamics under UV, an index of intra-range probability is put forward. Based on stochastic analysis theory, an analytic method is proposed to analyze the system frequency under UV, by which the intra-range probability can be analytically solved. Compared with Monte Carlo simulation in a typical SFR case and the Iceland electricity transmission network, the proposed method shows almost the same results using much less computation resource. Finally, insights for improving the SFR under UV are provided. The proposed method can be used to quickly verify whether the system frequency could withstand the UV and stay in the security range. [ABSTRACT FROM AUTHOR]

Time-domain simulation is the basis of dynamic security assessment for power systems. Traditionally, numerical integration methods are adopted by simulation software to solve nonlinear power system dynamics for any given contingency under a specific operating condition. An alternative simulation approach promising for online applications is to offline derive a semi-analytical solution (SAS) for power system differential equations and then online evaluate the SAS over consecutive time windows regarding the operating condition and contingency until the simulation result over a desired period is obtained. This paper proposes a general semi-analytical approach that derives and evaluates an SAS in the form of a power series in time to approximate the true solution. This paper provides an error-rate upper bound of the SAS for reliable use of adaptive time windows in evaluation of the SAS. To extend the semi-analytical approach for solving general power system differential-algebraic equations, this paper also proposes a dynamic bus method to efficiently link the SAS for dynamic components with the numerical solution of the network algebraic equations. Case studies on the New England 39-bus system and the Polish 2383-bus system test the performance of the proposed approach, compare it with other methods, and show the potentials of the proposed semi-analytical approach for online simulation. [ABSTRACT FROM AUTHOR]

This paper studies the impact of realistic wide-area measurement system (WAMS) time-varying delays on the dynamic behavior of power systems. A detailed model of WAMS delays including quasi-periodic, stochastic, and constant components is presented. Then, this paper discusses numerical methods to evaluate the small-signal stability as well as the time-domain simulation of power systems with inclusion of such delays. The small-signal stability analysis is shown to be able to capture the dominant modes through the combination of a characteristic matrix approximation and a Newton correction technique. A case study based on the IEEE 14-bus system compares the accuracy of the small-signal stability analysis with Monte Carlo time-domain simulations. Finally, the numerical efficiency of the proposed technique is tested through a real-world dynamic model of the all-island Irish system. [ABSTRACT FROM AUTHOR]

This paper investigates the torsional subsynchronous oscillations (SSOs) of synchronous generators caused by the grid-connected wind farms. The investigation does not rely on the representation of a wind farm by an aggregated wind generator and is based on a multi-input and multi-output closed-loop model. The model is comprised of the wind farm subsystem, which includes all the wind farms, and the subsystem of rest of power system (ROPS). Theoretical analysis proves that the open-loop SSO modal coupling of wind farm subsystem and ROPS subsystem results in the closed-loop SSO modal repulsion on the complex plane. Subsequently, damping of torsional SSOs decreases and growing SSOs may occur when the closed-loop modal repulsion is strong. Hence, closed-loop modal repulsion explains and reveals the mechanism about why the wind farms may cause the torsional SSOs in the power system. In addition, a method of open-loop modal analysis is proposed to detect the SSO instability risk brought about by the wind farms. The detection is based on the estimation of degree of closed-loop modal repulsion and only needs the modal information of open-loop subsystems. An example power system with wind farms is presented to demonstrate analysis and conclusions made in the paper. [ABSTRACT FROM AUTHOR]

A phasor measurement unit (PMU) only state estimator is intrinsically superior to its SCADA analogue with respect to speed, performance, and reliability. However, ensuring the quality of the data stream which enters the linear estimator is crucial before establishing it as the front end of an EMS or other network applications. One approach is to pre-process the phasor data before it arrives at the linear estimator. This paper presents an algorithm for synchrophasor data conditioning and repair that fits neatly as a prefix into the existing linear state estimation formulation. The methodology has been tested using field data obtained from PMUs installed in Dominion Virginia Power's (DVP's) EHV network. The results indicate that the proposed technique provides a computationally simple, elegant solution to the synchrophasor data quality problem. [ABSTRACT FROM PUBLISHER]

The paper addresses the problem of determining the maximum distributed energy resource (DER) capacity that can be connected to low-voltage (LV) networks without creating voltage-rise problems. That maximum capacity depends on the network characteristics and on the candidate sites for DER connection. When sites are multiple and LV networks are poorly characterized, such maximum capacity cannot be determined with power-flow or other admittance-matrix-based approaches. This paper proposes an approach to estimate voltage rise caused by DER under reduced network characterization. Such approach is built upon customary voltage and impedance measurements to be made at the sites of DER injection and gives sufficiently accurate results under most practical situations. The paper validates the accuracy of the proposed approach against exact power-flow results for well-characterized networks and load situations and provides guidelines for DER connection based on maximum capacity nodal allocation. [ABSTRACT FROM PUBLISHER]

The novel cascade-mitigation scheme developed in Part I of this paper is implemented within a receding-horizon model predictive control (MPC) scheme with a linear controller model. This present paper illustrates the MPC strategy with a case-study that is based on the IEEE RTS-96 network, though with energy storage and renewable generation added. It is shown that the MPC strategy alleviates temperature overloads on transmission lines by rescheduling generation, energy storage, and other network elements, while taking into account ramp-rate limits and network limitations. Resilient performance is achieved despite the use of a simplified linear controller model. The MPC scheme is compared against a base-case that seeks to emulate human operator behavior. [ABSTRACT FROM PUBLISHER]

This paper is concerned with the optimal power flow (OPF) problem. We have recently shown that a convex relaxation based on semidefinite programming (SDP) is able to find a global solution of OPF for IEEE benchmark systems, and moreover this technique is guaranteed to work over acyclic (distribution) networks. The present work studies the potential of the SDP relaxation for OPF over mesh (transmission) networks. First, we consider a simple class of cyclic systems, namely weakly-cyclic networks with cycles of size 3. We show that the success of the SDP relaxation depends on how the line capacities are modeled mathematically. More precisely, the SDP relaxation is proven to succeed if the capacity of each line is modeled in terms of bus voltage difference, as opposed to line active power, apparent power or angle difference. This result elucidates the role of the problem formulation. Our second contribution is to relate the rank of the minimum-rank solution of the SDP relaxation to the network topology. The goal is to understand how the computational complexity of OPF is related to the underlying topology of the power network. To this end, an upper bound is derived on the rank of the SDP solution, which is expected to be small in practice. A penalization method is then applied to the SDP relaxation to enforce the rank of its solution to become 1, leading to a near-optimal solution for OPF with a guaranteed optimality degree. The remarkable performance of this technique is demonstrated on IEEE systems with more than 7000 different cost functions. [ABSTRACT FROM PUBLISHER]

This paper develops a self-coherence method for detecting sustained oscillations using phasor measurement unit (PMU) data. Sustained oscillations decrease system performance and introduce potential reliability issues. Timely detection of the oscillations at an early stage provides the opportunity for taking remedial reaction. Using high-speed time-synchronized PMU data, this paper details a self-coherence method for detecting sustained oscillation, even when the oscillation amplitude is lower than ambient noise. Simulation and field measurement data are used to evaluate the proposed method's performance. It is shown that the proposed method can detect sustained oscillations and estimate oscillation frequencies with a low signal-to-noise ratio. Comparison with a power spectral density method also shows that the proposed self-coherence method performs better. [ABSTRACT FROM PUBLISHER]

To uncover the mechanism by which voltage-dependent loads (VDLs) influence electromechanical dynamics, this paper mathematically deduces the damping torque induced by VDLs based on a single machine infinite bus system. Moreover, by continuously regulating the terminal voltage of a typical large-scale VDL, i.e., the aluminum electrolysis load, this paper proposes a novel load damping control architecture to dynamically modulate the power consumption of controlled loads so as to eliminate interarea oscillations in power systems. Specifically, the decentralized load damping controllers (LDCs) used in this architecture are designed by a proposed multistage mixed ${{{H}}_{2}} / {{{H}}_\infty }$ control approach to guarantee robustness against uncertainties (e.g., tie-line outages and wind generation fluctuations) as well as to ensure reasonable control efforts of controlled VDLs. Simulation results on the modified New England and New York interconnected system validate the method for analysis of VDLs’ effects on interarea oscillations and show the proposed load damping control strategy can satisfactorily damp interarea oscillations over multiple operating points. [ABSTRACT FROM AUTHOR]

The control of reactive power exchange between grids of different voltage levels has always been a concern for system operators. With production moving from the transmission to the distribution level, its importance increases. This paper proposes a novel approach to estimate reactive power capability of the grid as a whole. A linearized analytical model for an estimation of available reactive power exchange at the interface between two grids has been developed. The maximum estimation error for the scenarios we tested was only 2%. The model gives the relation between important grid parameters and the supported reactive power. The conclusions drawn from the model are confirmed on typical Swedish distribution network with scattered wind power and small industry consumers. Common scenarios in development of distribution grids are applied to show relevant parameters influence. One studied scenario is replacement of overhead lines with cables. It is shown that this particular change enhances the reactive power capability of the grid which is directly seen from the analytical analysis without running any optimal power flow. The analytical model proposed in this paper gives fundamental understanding of the reactive power capability of radial distribution grids. [ABSTRACT FROM AUTHOR]

This paper presents a nonlinear dynamic model of grid-connected combined heat and power (CHP) system that can effectively simulate the thermoelectric interactions and examine the impact of the CHP on the power grid. Based on the theorems of mass balance and energy balance, this paper studies and analyses the principles and dynamic characteristics of the main CHP components, including gas internal combustion engine, synchronous generator, waste heat exchanger, water storage tank, exhaust-heat boiler, and gas fired boiler. Then, the nonlinear time-domain models for each component are built against input and output parameters in order to facilitate the study of CHP operation under various conditions. Subsequently, a simulation method that can deal with the coupling of all models with different time constants is proposed. Finally, dynamic simulation analysis of the developed CHP model is carried out on the MATLAB/Simulink. Extensive demonstration results show that the developed models are accurate to represent the thermoelectric interactions in the gird-connected CHP and capture the impact of these gird-connected CHPs on the power grid. This study is particularly beneficial to the design of new control strategies for CHPs to maximise its efficiency and stability value to the grid. [ABSTRACT FROM AUTHOR]

This paper presents a new security-constrained multiobjective optimal dispatch (SC-MOOD) framework for an economic and reliable operation of microgrids. The framework is developed based on a computationally effective multiobjective optimization technique, Pareto concavity elimination transformation (PaCcET). The new method considers grid steady-state and dynamic constraints while solving the optimal dispatch in both grid-connected and islanded modes. The constraints consist of power balance, voltage magnitude, line flows, power generation, frequency, and voltage transients. The proposed framework finds the most economic operating solutions to not only minimize the generation cost but also minimize the reliability cost. In this paper, the PaCcET is utilized to solve the SC-MOOD. The PaCcET uses an extraordinary transformation to first transfer all the points from a multiobjective space to a transformed objective space. It then solves a linear combination of transformed objectives using a single-objective optimizer to find all the nondominated points of the original multiobjective space. The performance of the new framework is verified using the simulation results in a microgrid with several distributed energy resources in both grid-connected and islanded modes. The results are then compared with two multiobjective optimization techniques, nondominated sorting genetic algorithm II and multiobjective particle swarm optimization, as two well-known benchmarks. [ABSTRACT FROM AUTHOR]

This paper analyzes different models for evaluating investments in energy storage systems (ESS) in power systems with high penetration of renewable energy sources. First of all, two methodologies proposed in the literature are extended to consider ESS investment: a unit commitment model that uses the “system states” (SS) method of representing time; and another one that uses a “representative periods” (RP) method. Besides, this paper proposes two new models that improve the previous ones without a significant increase of computation time. The enhanced models are the “system states reduced frequency matrix” model which addresses short-term energy storage more approximately than the SS method to reduce the number of constraints in the problem, and the “representative periods with transition matrix and cluster indices” (RP-TM&CI) model which guarantees some continuity between representative periods, e.g., days, and introduces long-term storage into a model originally designed only for the short term. All these models are compared using an hourly unit commitment model as benchmark. While both system state models provide an excellent representation of long-term storage, their representation of short-term storage is frequently unrealistic. The RP-TM&CI model, on the other hand, succeeds in approximating both short- and long-term storage, which leads to almost 10 times lower error in storage investment results in comparison to the other models analyzed. [ABSTRACT FROM AUTHOR]

Merchant transmission planning is considered as a further step toward the full liberalization of the electricity industry. However, previous modeling approaches do not comprehensively explore its social efficiency as they cannot effectively deal with a large number of merchant companies. This paper addresses this fundamental challenge by adopting a novel non-cooperative game-theoretic approach. Specifically, the number of merchant companies is assumed sufficiently large to be approximated as a continuum. This allows the derivation of mathematical conditions for the existence of a Nash equilibrium solution of the merchant planning game. By analytically and numerically comparing this solution against the one obtained through the traditional centralized planning approach, the paper demonstrates that merchant planning can maximize social welfare only when the following conditions are satisfied: a) fixed investment costs are neglected and b) the network is radial and does not include any loops. Given that these conditions do not generally hold in reality, these findings suggest that even a fully competitive merchant transmission planning framework, involving the participation of a very large number of competing merchant companies, is not generally capable of maximizing social welfare. [ABSTRACT FROM AUTHOR]

This paper proposes a novel comprehensive model of a rectifier-controlled induction motor drive for use in positive-sequence transient stability simulation (PSTSS) programs. The model is implemented to approximately capture the behavior of the point-on-wave drive model, and applied to investigate the dynamic performance of the advanced drive loads in system-level simulations. This positive-sequence drive model is systematically developed by reducing the detailed three-phase electrical and control representations into $dq$ axes positive-sequence formulations. For the positive-sequence model, the line-side rectifier is interfaced to the grid through a voltage source with separate $dq$ axes controls to regulate the active and reactive power of the drive. The machine-side inverter control system is represented based on rotor flux oriented control. The dc-link of the drive converter is implemented by employing the average model of the pulse width modulated converter, and is utilized to integrate the line-side rectifier and machine-side inverter. The proposed motor drive model is validated by comparing the performance with the electromagnetic transient point-on-wave drive model. The VAr support capability of the drive load model is investigated by incorporating the developed model into a composite load structure in PSTSS programs. Multiple units of the developed drive models are represented in large-scale transmission systems to examine the system-level responses of drive loads. [ABSTRACT FROM AUTHOR]

This paper presents an optimization approach for the placement of geomagnetically induced current (GIC) blocking devices (BDs) on power system transformers to mitigate the adverse effects of a geomagnetic disturbance (GMD). Solar storms lead to GMDs which, in turn, drive GICs along transmission lines and through transformer windings. GICs cause half-cycle saturation in power transformers, increase their shunt reactive power loss, lead to a significant lack of power system reactive power support, and, as a result, create voltage instability and, potentially, large-scale voltage collapse. To mitigate these detrimental effects, a long-term remedy is to install GIC BDs at the neutral point of transformers. Since these devices are fairly costly, their placement should be performed in an optimal manner. The optimization problem proposed in this paper minimizes the cost of BD placement while satisfying power system voltage and generator maximum reactive power limits. The numerical results demonstrate the effectiveness of the proposed method in maintaining an acceptable voltage profile for the power system in case of GMDs with any degree of severity. [ABSTRACT FROM AUTHOR]

This paper studies the feasibility of utilizing the reactive power of grid-connected variable-speed wind generators to enhance the steady-state voltage stability margin of the system. Allowing wind generators to work at maximum reactive power limit may cause the system to operate near the steady-state stability limit, which is undesirable. This necessitates proper coordination of reactive power output of wind generators with other reactive power controllers in the grid. This paper presents a trust region framework for coordinating reactive output of wind generators with other reactive sources for voltage stability enhancement. Case studies on 418-bus equivalent system of Indian southern grid indicates the effectiveness of proposed methodology in enhancing the steady-state voltage stability margin. [ABSTRACT FROM PUBLISHER]

This paper presents a methodology and set of validation criteria for the systematic creation of synthetic power system test cases. The synthesized grids do not correspond to any real grid and are, thus, free from confidentiality requirements. The cases are built to match statistical characteristics found in actual power grids. First, substations are geographically placed on a selected territory, synthesized from public information about the underlying population and generation plants. A clustering technique is employed, which ensures the synthetic substations meet realistic proportions of load and generation, among other constraints. Next, a network of transmission lines is added. This paper describes several structural statistics to be used in characterizing real power system networks, including connectivity, Delaunay triangulation overlap, dc power flow analysis, and line intersection rate. The paper presents a methodology to generate synthetic line topologies with realistic parameters that satisfy these criteria. Then, the test cases can be augmented with additional complexities to build large, realistic cases. The methodology is illustrated in building a 2000 bus public test case that meets the criteria specified. [ABSTRACT FROM AUTHOR]

Optimal power flow (OPF) programs must be able to provide sound operating points for power systems under different conditions while meeting a large number of constraints. These constraints, however, either due to the operating conditions at hand or by construction, can have linearly dependent gradients, thus defining ill-behaved feasible sets. This paper analyzes the use of an alternative set of optimality conditions, derived from the Fritz-John (FJ) conditions, to represent OPF solutions in such critical cases. Results are presented for realistic test systems. [ABSTRACT FROM PUBLISHER]

This paper presents a new method for studying electromechanical transients in power systems using three phase, combined transmission and distribution models (hybrid models). The methodology models individual phases of an electric network and associated unbalance in load and generation. Therefore, the impacts of load unbalance, single phase distributed generation and line impedance unbalance on electromechanical transients can be studied without using electromagnetic transient simulation (EMTP) programs. The implementation of this methodology in software is called the Three Phase Dynamics Analyzer (TPDA). Case studies included in the paper demonstrate the accuracy of TPDA and its ability to simulate electromechanical transients in hybrid models. TPDA has the potential for providing electric utilities and power system planners with more accurate assessment of system stability than traditional dynamic simulation software that assume balanced network topology. [ABSTRACT FROM PUBLISHER]

This paper introduces a framework of transient stability assessment for future distribution systems that are comprised of multiple microgrids. Enabled by the advances in power electronics and synchrophasor technologies, an angle droop method is introduced for autonomous real power sharing among coupling-operated microgrids. In our previous work, the small-signal stability criterion are derived. It is well-known that only regional transient stability can be established for conventional multi-machine systems interfaced with synchronous generators. In contrast, we show in this paper that asymptotical stability in the large can be achieved if angle droop method is adopted for real power sharing among coupled microgrids. Transient stability criterion is derived by formulating the linear matrix inequality (LMI) version of the Kalman-Yakubovich-Popov (KYP) conditions corresponding to the multi-variable Popov criterion. Numerical studies show the effectiveness of the proposed transient stability assessment framework for future power electronic-interfaced distribution systems. [ABSTRACT FROM PUBLISHER]

The method of symmetrical components is not effective for fault location in the case of untransposed lines, due to potential couplings between the sequence circuits. This paper proposes a non-iterative algorithm in the phase-coordinates for wide-area fault location on untransposed transmission networks. In doing so, first, an improved two-terminal method is suggested to accurately locate faults on untransposed lines. Next, an algorithm is proposed to infer voltage and current phasors at the faulted line ends without direct measurements, by taking advantage of the data provided by phasor measurement units (PMUs). Accordingly, the adverse effect of close instrument transformers transients on the estimation accuracy is minimized. Being highly nonlinear in terms of fault distance and impedance, the fault equations are derived and made linear in this paper by defining six suitable auxiliary variables. The resulting system of equations is solved using the least-squares method to obtain three-phase voltages and currents at the faulted line ends. A main feature of the proposed algorithm is that it only requires a limited number of current and voltage synchrophasors. An additional advantage of the proposed algorithm is that the faulted line is not required to be known a-priori. The proposed algorithm is validated using extensive simulation studies on the New England 39-bus test system, accounting for different fault locations, types and resistances. [ABSTRACT FROM PUBLISHER]

Multi-terminal High Voltage Direct Current (HVDC) using Voltage Source Converters (VSC-HVDC) is a promising technology which provides flexible control of active and reactive power and facilitates remote renewable energy integration, above all using long cables. This paper analyses an active power control strategy for multi-terminal VSC-HVDC systems tailored to enhance transient stability of hybrid AC/DC grids. The proposed strategy controls each VSC using frequency measurements of all terminals. Its performance is compared to a strategy in which each VSC is controlled using only local frequency measurements of the AC side, proving that the proposed strategy shows better performance, even taking into account reasonable communication delays. The paper also shows that the proposed strategy generally gives similar results to those obtained when each VSC is controlled using the speed of the centre of inertia (COI). The speed of the COI is a more comprehensive and richer figure than the one proposed in this paper but it is also much more complex to obtain. Simulation results with PSS/E of a test system have been used to illustrate the comparisons and the main contributions of the proposal. [ABSTRACT FROM PUBLISHER]

This paper presents a general framework for the doubly fed induction generator connected to a complex power system in order to facilitate the dynamic estimation of its states using noisy PMU measurements. State estimation considering the whole power system with the occurrence of electric faults is performed using the Unscented Kalman Filter (UKF) with a bad data detection scheme. Such a state estimation scheme for a DFIG is important because not all dynamic states of a DFIG are easily measurable. Furthermore, the proposed state estimation technique is decentralized and the network topology of the entire power system is taken into consideration in the estimation process. In order to enhance the error tolerance and self-correction of the power system, bad data detection technique is implemented. A performance comparison with Extended Kalman Filter (EKF) is also discussed. [ABSTRACT FROM PUBLISHER]

The paper proposes a semi-implicit formulation of the differential-algebraic equations (DAEs) describing power system models for transient stability analysis. This formulation, if coupled to an implicit integration scheme, shows two relevant advantages with respect to the conventional explicit formulation: (i) reduce the computational burden; and (ii) increase the sparsity of the Jacobian matrix of the system. The proposed model also allows using null time constants and thus simplifies the computer implementation of the DAEs. The properties and the performance of the proposed semi-implicit formulation and the conventional explicit one are compared through a dynamic 21,177-bus model of the European transmission system. [ABSTRACT FROM PUBLISHER]

This paper summarizes simulation based technical feasibility and cost benefit analyses of a range of off-the-shelf electrical losses reduction intervention solutions in the Isle of Wight (IoW) 11 kV distribution network in the United Kingdom (UK), assessed over a period of 45 years. Based on presented results, the paper provides a brief commentary on the merits, drawbacks, risks and recommendations associated with each considered network intervention. Among considered network interventions, the transformer auto stop-start scheme, where one of the transformers among a pair at a primary substation would be switched depending on the substation's varying load, was found to be the optimal solution, i.e., in reducing technical losses significantly and may also have a reasonable Net Present Value (NPV) with a good rate of Return on Investment (RoI) when fully implemented. [ABSTRACT FROM PUBLISHER]

The reliable operation of a power distribution system relies on a good prior knowledge of its topology and its system state. Although crucial, due to the lack of direct monitoring devices on the switch statuses, the topology information is often unavailable or outdated for the distribution system operators for real-time applications. Apart from the limited observability of the power distribution system, other challenges are the nonlinearity of the model, the complicated, unbalanced structure of the distribution system, and the scale of the system. To overcome the above challenges, this paper proposes a Bayesian-inference framework that allows us to simultaneously estimate the topology and the state of a three-phase, unbalanced power distribution system. Specifically, by using the very limited number of measurements available that are associated with the forecast load data, we efficiently recover the full Bayesian posterior distributions of the system topology under both normal and outage operation conditions. This is performed through an adaptive importance sampling procedure that greatly alleviates the computational burden of the traditional Monte-Carlo (MC)-sampling-based approach while maintaining a good estimation accuracy. The simulations conducted on the IEEE 123-bus test system and an unbalanced 1282-bus system reveal the excellent performances of the proposed method. [ABSTRACT FROM AUTHOR]

This paper develops a computationally efficient algorithm which speeds up the probabilistic power flow (PPF) problem by exploiting the inherently low-rank nature of the voltage profile in electrical power distribution networks. The algorithm is accordingly termed the Accelerated-PPF (APPF), since it can accelerate “any” sampling-based PPF solver. As the APPF runs, it concurrently generates a low-dimensional subspace of orthonormalized solution vectors. This subspace is used to construct and update a reduced order model (ROM) of the full nonlinear system, resulting in a highly efficient simulation for future voltage profiles. When constructing and updating the subspace, the power flow problem must still be solved on the full nonlinear system. In order to accelerate the computation of these solutions, a Neumann expansion of a modified power flow Jacobian is implemented. Applicable when load bus injections are small, this Neumann expansion allows for a considerable speed up of Jacobian system solves during the standard Newton iterations. APPF test results, from experiments run on the full IEEE 8500-node test feeder, are finally presented. [ABSTRACT FROM AUTHOR]

Volt/VAr Optimization (VVO) is becoming increasingly crucial in distribution management systems with renewable sources that require setting their reactive power in coordination with legacy voltage and reactive power control devices. This paper presents a VVO method that operates in complex variables based on the Wirtinger calculus; it employs a penalty method that keeps voltage magnitudes and controller parameters within limits together with a probabilistic rounding technique for handling switched device variables. The complex variable implementation permits using the compensation technique when solving the Karush-Kuhn Tucker (KKT) system, thus achieving a significant speedup due to limiting the number of linear system factorizations. The proposed method is contrasted with a classical VVO implementation employing discrete coordinate search from the current operating point and an enhanced version that uses sensitivity information. Numerical results on distribution networks having up to 3147 nodes show that the proposed method is significantly faster than classical methods and gives operating points free of voltage magnitude violations and lower power loss. [ABSTRACT FROM AUTHOR]

This paper proposes a cascading failure simulation (CFS) method and a hybrid machine learning method for vulnerability analysis of integrated power-gas systems (IPGSs). The CFS method is designed to study the propagating process of cascading failures between the two systems, generating data for machine learning with initial states randomly sampled. The proposed method considers generator and gas well ramping, transmission line and gas pipeline tripping, island issue handling and load shedding strategies. Then, a hybrid machine learning model with a combined random forest (RF) classification and regression algorithms is proposed to investigate the impact of random initial states on the vulnerability metrics of IPGSs. Extensive case studies are carried out on three test IPGSs to verify the proposed models and algorithms. Simulation results show that the proposed models and algorithms can achieve high accuracy for the vulnerability analysis of IPGSs. [ABSTRACT FROM AUTHOR]

Over the past 20 years, the rapid integration of renewable energy has resulted in electricity markets that are increasingly complex, interconnected, and uncertain. Similar to the banking system's financial crisis in 2008 due to chained reactions, severe financial losses due to uncertainty at a large renewable farm could induce significant financial losses at other market participants. The spread of such financial shocks can be worsened by centralized market clearing, and systemic risks consequently germinate in electricity market operations. Therefore, our previous work has compared systemic risk with systematic risk in the electricity market with uncertainties. However, the scope of our previous work has been limited to risk indices. This paper aims to broaden the study by proposing the theoretical foundation of systemic risk analysis in electricity markets with uncertainties. First, an electricity market financial network is defined to describe the cash inflow/outflow of all participants, and the financial contagion is employed to model the interlinks between different entities. Then, two financial properties, financial resilience and financial reliability, are proposed to evaluate the systemic risk in market settlements with uncertainties. Finally, the proposed theoretical foundation of systemic risk is demonstrated on the Texas synthetic 2000-bus system with 70% renewable penetration. [ABSTRACT FROM AUTHOR]

The foreseen development of large-scale Offshore Windfarms (OWFs) further from the shore dictates that the OWF transmission system must be optimally designed based on Dynamic Thermal Rating (DTR) in order to fully utilize the intermittent nature of the wind and to keep the offshore wind cost-competitive. In this paper, a comprehensive, DTR-based, two-stage stochastic model is presented, which has been developed for investment decision support for OWF size and HVAC transmission systems. Complex DTR models for all the critical HV components are made fit for the mixed-integer linear programming problem, while accounting for the stochasticity in wind generation and component availability. The main decisions incorporate the discrete size of OWFs, HV subsea export cable cross-sections and ratings for transformers and shunt reactors. For validation, an actual testcase OWF off the east coast of U.K. has been used. Results indicate that DTR-based iterative design of OWF and its transmission components can significantly improve the business case, even though transmission efficiency and energy delivered are not maximum for the optimal design [ABSTRACT FROM AUTHOR]

Uncertainties in renewable generation make accurate load forecast essential for reliable power system operation. This paper considers energy imbalance market (EIM), where market players are allowed to procure energy ahead of time and trade the mismatch due to forecast error and strategic behaviors. The ISO sets the trading prices according to the market conditions, and pursues various system-level objectives. We first identify the power-law relationship between data volume and forecast accuracy, which enables the formulation of forecast cost model. Then, we cast the interactions in the EIM in the Stackelberg game framework with the ISO acting as the leader. We offer explicit subgame perfect equilibrium among the players in EIM, and derive the sufficient condition for the existence of unique equilibrium. Then, we show that this equilibrium, if exists, supports the maximal social welfare and under certain conditions, minimizes the total mismatch. We further examine the local and global impacts of the forecast errors under mild conditions, together with robustness analysis. Such analysis provides mechanism design guidelines for the ISO to enable the data sharing and forecast method sharing among market players in the EIM. Numerical studies further examine the effectiveness, robustness and sensitivity of the subgame. [ABSTRACT FROM AUTHOR]

Due to the increasing penetration of large-scale renewable energy generation at transmission level, hybrid AC/DC transmission expansion is becoming more relevant by the day, especially if the considered renewable generation is far away from existing AC grid infrastructure. This paper presents a multi-period hybrid AC/DC network expansion planning model that incorporates node voltages, reactive power and network losses. Since the operation of a high voltage DC link is influenced considerably by the converter stations, converter transformer, filter, and phase reactor are modeled in each converter station. Since the AC power flow equations render a non-convex problem whose solution algorithms do not always guarantee convergence or optimality, a second-order conic relaxation is utilized. The resulting model is a mixed-integer convex problem with a convergence guarantee that embodies a better approximation of system operation than its DC linear counterpart. Three case studies are considered to illustrate the proposed model. [ABSTRACT FROM AUTHOR]

This paper presents a new formulation for the preventive security-constrained unit commitment problem modeling N-k line outages and transmission losses. The pre- and post-contingency transmission constraints, representing N-k line outages, are explicitly included by using generalized generation distribution factors. To account for security, a contingency selection procedure based on line outage distribution factors finds a list of worst-case contingencies. Transmission losses are incorporated using piecewise linear expressions. The proposed model is formulated as an instance of mixed-integer linear programming. The effectiveness of the proposed approach is illustrated with the IEEE 57-bus system and the 1,354-bus portion of the European transmission system. As empirically evidenced, the explicit consideration of N-k line outages and transmission losses leads to different decisions in the generation scheduling and dispatch, ensuring secure power system operation. [ABSTRACT FROM AUTHOR]

State estimation plays a key role in the transition from the passive to the active operation of distribution systems, as it allows to monitor the networks and provides the necessary information to perform control actions. However, designing state estimators for distribution systems is challenging, due to the characteristics of the networks, such as limited measurement availability. Furthermore, the features of the distribution system present significant local variations, e.g., voltage level and number and type of customers, which makes it hard to design a “one-size-fits-all” state estimator. This paper introduces a unifying framework that allows to easily implement and compare diverse unbalanced static state estimation models. This is achieved by formulating state estimation as a general constrained optimization problem. The advantages of this approach are described and supported by numerical illustration on a large set of real distribution feeders. The framework is also implemented in software and made available open-source. [ABSTRACT FROM AUTHOR]

The stability of power systems can largely limit the power transfer capability limit of transmission lines. The PV generator control is different from synchronous generator control. The impact of PV generator dynamics on the power transfer limit constrained by stability is not well explored in the literature. This paper focuses on improving the stability constrained power transfer capability limit of transmission lines emanating from PV generators. The PV generator is provided with dc link voltage and reactive power control and is equipped with low voltage ride through capability, voltage and frequency support functionalities. In this paper, Lyapunov function analysis based adaptive tuning laws are proposed for PV control parameters to improve the power transfer capability limit (constrained by stability) of transmission lines connecting PV generators to grid. The tuning laws are proposed for Phase Locked Loop (PLL), outer and inner control loop parameters. The proposed tuning laws have inherent robustness towards faults, changes in solar irradiation, changes in grid topology, network impedances, generation and loads in the system. The effectiveness of the proposed method is validated on a Single PV-Synchronous Machine system, modified IEEE-39 and IEEE-118 bus system. The performance of the proposed method is investigated considering various disturbances such as symmetrical and asymmetrical faults on transmission line, switching of a transmission line and change in solar irradiation of PV. Comparison with existing method shows that the proposed tuning method can achieve higher power transfer capability limit considering stability. [ABSTRACT FROM AUTHOR]

This paper proposes a dynamic valuation framework to determine the opportunity value of battery capacity degradation in grid applications based on the internal degradation mechanism and utilization scenarios. The proposed framework follows a dynamic programming approach and includes a piecewise linear value function approximation solution that solves the optimization problem over a long planning horizon. The paper provides two case studies on price arbitrage and frequency regulation using real market and system data to demonstrate the broad applicability of the proposed framework. Results show that the battery lifetime value is critically dependent on both the external market environment and its internal state of health. On the grid service side, results show that second-life batteries can provide more than 50% of the value compared to new batteries, and frequency regulation provides two times more revenue than price arbitrage throughout the battery lifetime. [ABSTRACT FROM AUTHOR]

Construction of the linearized state-space model is the key step of eigenvalue analysis for SSO study of power systems with large-scale renewable power generation (RPG) integrated. This paper proposes a novel method to construct the state matrix of the AC/DC hybrid power system with RPG within the discrete-time domain. The continuous-time state-space model of each AC/DC component as well as RPG units in the power system, is discretized together with their corresponding control. The discretized equation of each component is then represented by an equivalent circuit consisting of parallel historical current and conductance. According to the power system configuration, the discrete-time equivalent circuit of the whole AC/DC hybrid system is established, and the nodal analysis method is applied for the construction of the discrete-time state-space model of the power system. In this way, the state matrix can be acquired much more conveniently than that of continuous-time state-space method, which needs topology analysis to find independent state variables of the network from the proper tree. The proposed method has been applied in the eigenvalue analysis for the SSO study of a case system adapted from the AC/DC hybrid transmission system in northwest China. Eigenvalue results are in high accordance with time-domain simulation results in PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]