Search

This paper summarizes simulation based technical feasibility and cost benefit analyses of a range of off-the-shelf electrical losses reduction intervention solutions in the Isle of Wight (IoW) 11 kV distribution network in the United Kingdom (UK), assessed over a period of 45 years. Based on presented results, the paper provides a brief commentary on the merits, drawbacks, risks and recommendations associated with each considered network intervention. Among considered network interventions, the transformer auto stop-start scheme, where one of the transformers among a pair at a primary substation would be switched depending on the substation's varying load, was found to be the optimal solution, i.e., in reducing technical losses significantly and may also have a reasonable Net Present Value (NPV) with a good rate of Return on Investment (RoI) when fully implemented. [ABSTRACT FROM PUBLISHER]

Smart inverters provide additional control capability to help optimize the operation of distribution systems. This paper proposes a framework for exact optimal active and reactive power dispatch of distributed photovoltaic (PV) generation, switched capacitors, and voltage regulators in large multi-phase unbalanced distribution systems. The objectives of the optimal dispatch are minimization of the energy loss, PV active power curtailment, and operations of capacitors and voltage regulators, in addition to elimination of voltage violations and reverse power flow. The optimization problem is formulated in rectangular coordinates as a nonlinear, nonconvex problem. Effective computational strategies are proposed to allow the application of predictor-corrector primal-dual interior point method to solve optimization problems in real-time with a large number of constraints and variables, including discrete variables corresponding to switched capacitors and voltage regulators. The accuracy of the numerical solution and the ability to implement the proposed framework are validated using the unbalanced multi-phase IEEE 34-bus and EPRI 2,998-bus distribution systems with 15-minute load and PV data. The results show a significant loss reduction and elimination of both voltage violations and reverse power flow. [ABSTRACT FROM AUTHOR]

The discrete coordinate-descent algorithm is a practical approach that is currently used in centralized Volt/VAr Control (VVC) implementations, mainly due to its good performance and speed for real-time applications. Its viability is however challenged by the increasing number of distributed generation that contribute to the VVC solution, in addition to the conventional transformer taps and switched capacitors. This paper presents the exact computation of sensitivity factors that speed up the discrete coordinate-descent implementation, by significantly reducing the number of forward/backward substitutions in the current injection power flow method; the speed up is achieved without affecting the control setting quality of the original implementation. The optimality of the discrete coordinate-descent solutions is investigated by computing the gaps relative to mixed-integer linear programming set-points, derived from a polyhedral reformulation of the VVC problem. The sensitivity-based discrete coordinate-descent algorithm is tested starting from two initial points, the default one given by the current control set-points, and a continuous solution obtained from a linear approximation of the VVC problem. Numerical results on networks with up to 3145 nodes show that the sensitivity-based approach significantly improves the runtime of the discrete coordinate-descent algorithm, and that the linear programming initialization leads to VVC solutions with gaps relative to the mixed-integer set-points that are less than 0.5%. [ABSTRACT FROM PUBLISHER]

This paper proposes a two-level voltage controller for large-scale power systems. The aim of the controller is to maintain a near-optimal voltage profile in the transmission network by coordinating discrete reactive power (var) control devices in the system. The controller is targeted for implementation in electric power transmission utility companies where most of the voltage controls are coordinated by switching of discrete var devices such as shunt capacitor and reactor banks and transformer banks load tap changers (LTCs). By effectively dividing the controller responsibilities between local substation controls and a central coordinator at control center level, the design is aimed at voltage control of large-scale power systems. At local level, the substation controllers maintain their respective substation bus voltages by local power-flow-like computations using mostly local PMU measurements. The central coordinator computes and provides the voltage set-points to the substation controllers and also coordinates by enabling or disabling the local controllers as needed. The controller is being designed towards prototype implementation in Southern California Edison (SCE), starting with local controllers at specific substations in the first stage. It is tested on real-time dynamic models and large-scale power-flow simulations of SCE transmission network. [ABSTRACT FROM AUTHOR]

This paper deals with the management of voltage constraints in active distribution systems that host a significant amount of distributed generation (DG) units. To this end we propose a centralized optimization approach which aims at minimizing the amount of MW curtailment of non-firm DG to remove voltage constraints. The salient feature of this approach is that it comprehensively and properly models the full variety of possible control means (i.e., DG active/reactive power including DG shut-down, on load tap changing transformer ratio, shunt capacitor, and remotely controlled switches or breakers), most of which having a discrete behavior. We develop and compare the performances of two optimization models on a snapshot basis for various distribution systems up to 1089 buses. In particular we show that the use of remotely controlled switches so as to transfer DG between feeders in case of voltage constraints may lead to significant reduction of the DG curtailment. [ABSTRACT FROM AUTHOR]

The uptake of variable megawatts from photovoltaics (PV) challenges distribution system operation. The primary problem is significant voltage rise in the feeder that forces existing voltage control devices such as on-load tap-changers and line voltage regulators to operate continuously. The consequence is the deterioration of the operating life of the voltage control mechanism. Also, conventional non-coordinated reactive power control can result in the operation of the line regulator at its control limit (runaway condition). This paper proposes an optimal reactive power coordination strategy based on the load and irradiance forecast. The objective is to minimize the number of tap operations so as not to reduce the operating life of the tap control mechanism and avoid runaway. The proposed objective is achieved by coordinating various reactive power control options in the distribution network while satisfying constraints such as maximum power point tracking of PV and voltage limits of the feeder. The option of voltage support from PV plant is also considered. The problem is formulated as constrained optimization and solved through the interior point technique. The effectiveness of the approach is demonstrated in a realistic distribution network model. [ABSTRACT FROM PUBLISHER]

Deploying shunt capacitor banks in distribution systems can effectively reduce the power loss and provide additional benefits for system operation. In practice, the power loss on distribution transformers can account for a considerable portion of the overall loss. This paper proposes a method for optimal placement of capacitor banks to the distribution transformers to reduce power loss. The capacitor bank locations are considered at the low-side of transformers. The net present value (NPV) criterion is adopted to evaluate the cost benefit of the capacitor installation project. First, an explicit formula for directly calculating the power loss of radial distribution systems is derived. Then, the optimal capacitor bank placement is formulated as a mixed-integer programming (MIP) model maximizing the NPV of the project subject to certain constraints. The model is suitable for being solved by commercial MIP packages, and the operational control of the capacitor banks to maximize the power loss reduction can be simply achieved by local automatic switching according to VAR measurements. The proposed method has been practically applied in the Macau distribution system, and the simulation results show that the proposed method is computationally efficient, and a considerable positive NPV can be obtained from the optimal capacitor bank placement. [ABSTRACT FROM PUBLISHER]